Search Results (94)

Limited recovery of the viscoelastic properties of aged asphalt on RAP surfaces at ambient temperature reduces interface fusion and bonding with new emulsified asphalt, degrading pavement performance and limiting large-scale promotion and high-value applications of the emulsified asphalt cold recycled mixture (EACRM). Therefore, a cold regenerant was independently prepared to rapidly penetrate, soften, and activate aged asphalt at ambient temperature in this paper, and its effects on the volumetric composition, mechanical strength, and pavement performance of EACRM were systematically investigated. The results showed that as the cold regenerant content increased, the air voids, indirect tensile strength (ITS), and high-temperature deformation resistance of EACRM decreased, while the dry–wet ITS ratio, cracking resistance, and fatigue resistance increased. Considering the comprehensive pavement performance requirements of cold recycled pavements, the optimal content of the activated cold regenerant for EACRM was determined to be approximately 0.6%. Full article

In actual service, asphalt pavement is subjected to freeze–thaw cycles and ultraviolet radiation (UV) over the long term, which can easily lead to mixture aging, enhanced brittleness, and structural damage, thereby reducing pavement durability. This study focuses on the influence of freeze–thaw cycles and ultraviolet aging on the performance of recycled asphalt mixtures. Systematic indoor road performance tests were carried out, and a fatigue prediction model was established to explore the comprehensive effects of recycled asphalt pavement (RAP) content, environmental action (ultraviolet radiation + freeze–thaw cycle), and other factors on the performance of recycled asphalt mixtures. The results show that the high-temperature stability of recycled asphalt mixtures decreases with the increase in environmental action days, while higher RAP content contributes to better high-temperature stability. The higher the proportion of old materials, the more significant the environmental impact on the mixture; both the flexural tensile strain and flexural tensile strength decrease with the increase in environmental action time. When the RAP content increased from 30% to 50%, the bending strain continued to decline. With the extension of environmental action days, the decrease in the immersion Marshall residual stability and the freeze–thaw splitting strength became more pronounced. Although the increase in RAP content can improve the forming stability, the residual stability decreases, and the freeze–thaw splitting strength is lower than that before the freeze–thaw. Based on the fatigue test results, a fatigue life prediction model with RAP content and freeze–thaw cycles as independent variables was constructed using the multiple nonlinear regression method. Verification shows that the established prediction model is basically consistent with the change trend of the test data. The research results provide a theoretical basis and optimization strategy for the performance improvement and engineering application of recycled asphalt materials. Full article

This study proposes a method for separating asphalt and aggregates in recycled asphalt pavement (RAP) materials using surfactants as solvents. This method utilizes surfactants to soften the asphalt by reducing its surface tension, separating the RAP clusters, and washing away the asphalt from the RAP. The wastewater is recycled during the emulsification–separation process without discharge. Factors affecting the separation effect of RAP, including the type of anionic surfactants, the surfactant concentration, the emulsion-to-RAP ratio, temperature, the rotation rate and time, and the RAP’s particle size, were investigated in depth, and the separation effect and its influence on the aggregate properties were evaluated. The experimental results indicate that when using the optimal process to mix and treat 13.2 mm and 9.5 mm RAP clusters, it is possible to achieve 100% separation of the coarse RAP above 4.75 mm, with a 64.58% reduction in the asphalt content. The angularity of the aggregate remained unchanged after separation. It was observed from scanning electron microscopy (SEM) images that the asphalt on the surface of the coarse aggregate had been eluted, and the morphology of the aggregate surface was completely exposed. This environmentally friendly separation method provides new possibilities for high-content RAP recycling in pavement engineering. Full article

To improve the recycling content of Reclaimed Asphalt Pavement (RAP), this paper utilizes the characteristic of aged and hardened asphalt in RAP materials by adopting the High-modulus Asphalt Mixture design method for high-RAP-content recycling. First, the basic technical performance, fatigue properties, rheological characteristics, and chemical functional groups of reclaimed asphalt, 30# hard asphalt, and Styrene-Butadiene-Styrene (SBS)-modified asphalt were analyzed. The results revealed significant similarities in various metrics between reclaimed and hard asphalt, demonstrating the feasibility of replacing hard asphalt with reclaimed asphalt in a High-modulus Asphalt Mixture design. Next, High-modulus Asphalt Mixtures, EME13, with different RAP contents (0%, 20%, 40%, 60%) were designed and compared with SBS-modified Sup13 mixtures. The results indicated that (1) as the RAP content increased, the high-temperature performance of EME13 improved by 20~60%, while its low-temperature and intermediate-temperature crack resistance slightly declined by 10~20%. The dynamic modulus in the low-frequency region increased by 3~6 times, whereas the high-frequency dynamic modulus decreased by 20~30%. RAP enabled EME13 to meet the modulus design requirements more readily for High-modulus Asphalt Mixtures. (2) Although the SBS-modified Sup13 exhibited superior pavement performance compared to EME13, its cost was significantly higher. EME13 with high RAP content demonstrated notable economic advantages despite slightly lower pavement performance than Sup13. This research provides a new technical approach for the high-content recycling of RAP materials. Full article

Stone mastic asphalt (SMA) is the most widely adopted asphalt mixture on highway pavement in China. However, the cost of SMA is rising continually due to the increasing shortage of high-quality basalt aggregate. On the other hand, China’s steel slag and reclaimed asphalt pavement (RAP) stock is abundant, and steel slag has excellent strength and wear-resistant performance, which can fully or partially replace part of the basalt aggregate. The content of asphalt may be increased due to the porosity of the steel slag. If fine RAP rich in asphalt is also used for SMA, it can partially fill the voids of steel slag and reduce the amount of new asphalt and fine aggregate. For this objective, SMA 13 was designed with two particle sizes of coarse steel slag aggregate (5–10 mm, 10–15 mm) and one fine RAP (0–5 mm), named SR-SMA. The fundamental pavement performance of SR-SMA was evaluated through a wheel-tracking test, low-temperature beam bending test, freeze–thaw indirect tensile test, and four-point bending fatigue test. For comparison, the mix design and performance tests of two SMAs involving coarse steel slag and fine basalt aggregate (named SB-SMA), and coarse and fine basalt aggregates (named B-SMA), respectively, were conducted. The results indicated that SR-SMA (dynamic stability of 4865 passes/mm) shows the best rutting resistance, followed by SB-SMA (dynamic stability of 4312 passes/mm), and B-SMA (dynamic stability of 4135 passes/mm) comes in last. Additionally, the dynamic stability values of three SMAs have significant differences. SR-SMA has better low-temperature cracking resistance with a failure strain of 3150 με, between SB-SMA and B-SMA (failure strain values are 4436, 2608 με). Compared to B-SMA and SB-SMA, the moisture stability of SR-SMA is relatively poor but meets Chinese specification. While the fatigue resistance of SR-SMA is the worst among three SMAs, their differences are insignificant. Furthermore, SR-SMA reduces material cost by approximately 35% per ton compared to conventional B-SMA. Overall, SR-SMA is cost-effective and can be used as an alternative material to traditional B-SMA. Full article

In south China, suffering from the rainiest climate, porous asphalt mixtures have been receiving increasing attention. However, with the increase in the application of pavement and the growth of service life, the importance of the recycling application of old reclaimed porous asphalt pavement (RPAP) has gradually become prominent. Based on this, this paper established RPAP content ranging from 0% to 30% in increments of 5% and designed experimental groups with and without regenerating agent to investigate the effects of RAP content and regenerating agent addition on the high-temperature stability, low- and normal-temperature crack resistance, moisture susceptibility, drainage capacity, and mechanical properties of PAC-13 reclaimed porous asphalt mixtures. Subsequently, the practical performance of PAC-13 RPAP was verified through a pavement test. The results indicate that, as the RPAP content increases, the high-temperature stability and mechanical properties of the recycled mixture improve. Specifically, as the planer content is increased to 30%, the dynamic stability of the regenerated porous asphalt increases by 61.1%, and the dynamic modulus at 25 Hz also shows an increase of 25.3%. However, the crack resistance, moisture susceptibility, and drainage capacity at both low temperatures and room temperature exhibited accelerated weakening. When the RPAP content increases to 30%, the reduction in failure strain of regenerated PAC-13 reaches 41.8%, and the reduction in submergence stability reaches 21%. Simultaneously, the water permeability coefficient, void ratio, and interconnected void ratio all demonstrate significant reductions of 23.5%, 6.5%, and 10.0%, respectively, indicating a diminished drainage capacity in the recycled porous pavement mixture. Then again, with the addition of the regenerant, the high-temperature stability of the regenerated porous mixture is reduced by 10.8%, and the mechanical properties are reduced by 6.48%, while the crack resistance at low temperature and room temperature, moisture susceptibility, and drainage ability are enhanced. The verification results of the test section demonstrate the feasibility of utilizing reclaimed asphalt pavement (RAP) material in the porous asphalt mixture. Additionally, it is recommended to select RAP material with a particle size of 4.75 mm or larger while ensuring that the proportion of RAP does not exceed 20%. The research findings of this paper are anticipated to offer guidance for the preparation of PAC-13 reclaimed porous asphalt mixtures while facilitating the recycling and large-scale utilization of old porous pavement materials. Full article

This study investigates the effects of two separation processes: traditional separation technology (TST) and refined separation technology (RST), on the characteristics of recycled asphalt pavement (RAP) and the performance of cold patching asphalt mixtures (CPAM). The research evaluates the RAP separation efficiency, focusing on asphalt content and agglomeration degree, and examines the mechanical, high- and low-temperature, moisture susceptibility, anti-stripping, and fatigue performance of CPAM with varying RAP content (0–75%). A key innovation of this study is the exploration of using RST-RAP for CPAM production in comparison to TST-RAP. The findings reveal that the RST process significantly enhances the separation of coarse aggregates from asphalt mortar, leading to improved gradation, reduced agglomeration, and better overall RAP quality compared to TST. Incorporating RAP into CPAM improved the Marshall stability, with RST-RAP showing higher performance gains than TST-RAP, particularly at higher RAP content. Additionally, the dynamic stability, low-temperature cracking resistance, moisture resistance, and fatigue life of CPAM were positively influenced by RST-RAP, with optimal performance achieved at 25–50% RAP content. In contrast, excessive RAP content, especially with TST-RAP, negatively impacted the mixture’s properties, leading to higher brittleness and reduced stability. This study highlights the novelty of using RST-RAP to enhance CPAM performance, suggesting that the RST process is more effective in improving CPAM performance. However, RAP content should be carefully controlled (25–50% for RST-RAP and ≤25% for TST-RAP) to meet technical standards and ensure optimal durability. These findings provide valuable insights for optimizing RAP utilization in sustainable pavement maintenance practices. Full article

The increasing demand for sustainable road construction materials necessitates innovative solutions to overcome the challenges of Recycled Asphalt Pavement (RAP), including aged binder brittleness, reduced flexibility, and durability concerns. Waste Plastic Aggregates (WPA) offer a promising alternative; however, their thermal aging behavior and interactions with RAP remain insufficiently understood. This study evaluates the performance of RAP-based asphalt mixtures, incorporating three types of WPA—Low-Density Polyethylene (LDPE), High-Density Polyethylene (HDPE), and Polypropylene (PP)—under three thermal aging conditions: mild (60 °C for 7 days), moderate (80 °C for 14 days), and severe (100 °C for 30 days). The mixtures were designed with 30% RAP content, 10% and 20% WPA by aggregate weight, and SBS-modified binder rejuvenated with 2% and 4% sewage sludge bio-oil by binder weight. It is considered that thermal aging may impact the performance of WPA in RAP mixtures; therefore, this study evaluates the durability and mechanical properties of RAP mixtures incorporating LDPE, HDPE, and PP under varying thermal aging conditions to address these challenges. The results showed that incorporating WPA and bio-oil significantly enhanced the mechanical performance, durability, and sustainability of asphalt mixtures. Marshall Stability increased by 12–23%, with values ranging from 12.6 to 13.2 kN for WPA-enhanced mixtures compared to 12.7 kN for the control. ITS improved by 15–20% in dry conditions (1.34–1.44 MPa) and 12–18% in wet conditions (1.15–1.19 MPa), with TSR values reaching up to 82.64%. Fatigue life was extended by 28–43%, with load cycles increasing from 295,600 for the control to 352,310 for PP mixtures. High-temperature performance showed a 12–18% improvement in softening point (57.3 °C to 61.2 °C) and a 23% increase in rutting resistance, with rut depths decreasing from 7.1 mm for the control to 5.45 mm for PP mixtures after 20,000 passes. These results demonstrate that combining RAP, WPA, and bio-oil produces sustainable asphalt mixtures with superior performance under aging and environmental stressors, offering robust solutions for high-demand applications in modern infrastructure. Full article

The granular bases commonly used in the construction of road infrastructure projects often require a high consumption of raw materials. The potential utilization of recycled materials, specifically Reclaimed Asphalt Pavement (RAP) derived from road asphalt pavement demolition, emerges as a promising sustainable advantage for infrastructure projects, considering its potential environmental and cost benefits in other layers of the structure. In this context, this research proposes a feasibility study on the use of RAP as a granular base layer, supported by an advanced laboratory analysis that includes a range of tests simulating the in-service conditions as well as a full-scale demonstration of the material behavior under static and dynamic loads. Various design variables, such as different gradations and binder content, are considered. The results demonstrate that, despite having discontinuous gradation and smaller aggregate sizes than those commonly applied in natural base layers, the evaluated recycled materials exhibit a higher load-bearing capacity and resistance to permanent deformation than the reference materials commonly used as granular bases. Notable enhancements of up to 30% in elastic modulus, coupled with reductions of around 20% in permanent deformations, have been documented using the asphalt cement potential in the old pavement. Full article

High-quality oocyte production strategies play an important role in animal-assisted reproductive biotechnologies, and rapamycin (Rap) has been commonly used to increase the development potential of mammalian oocytes. The purpose of this study is to evaluate the effects and possible molecular mechanisms of rap on the maturation of yak oocytes. Different concentrations of Rap were supplemented during in vitro maturation (IVM) of yak oocytes. The maturation rates of oocytes and development rates of parthenogenetically activated embryos were assessed. The levels of 17β-estradiol (E2) were detected via ELISA, and the expression of autophagy-related factors, steroidogenic enzymes, and HIF-1α was detected via qRT-PCR, western blotting, and fluorescence microscopy, respectively. In addition, the impacts of E2 and HIF-1α on Rap-mediated oocyte autophagy were investigated by investigating the activities of E2 and HIF-1α. Our results showed that 0.1 nM Rap substantially enhanced the developmental ability of yak oocytes. In this group, the levels of E2, CYP19A1, CYP17A1, and autophagy-related factors were also significantly increased, and the expression of ATG5 and BECN1 in subsequent embryos was also increased. Further analysis revealed that Rap tends to enhance the development competence of yak oocytes and that the levels of autophagy-related factors are reduced when the activity of E2 or HIF-1α is inhibited. Furthermore, the levels of E2, CYP19A1, and CYP17A1 were downregulated when the activity of HIF-1α was inhibited, and the levels of HIF-1α were also significantly reduced by the estrogen receptor antagonist G15. Nevertheless, the levels of CYP11A1 mRNA in mature yak COCs were not significantly different among these groups, a phenomenon which implies that the levels of E2 were not correlated with the CYP11A1 content in yak COCs. There was an increasing tendency for the development competence of yak oocytes at the optimum concentration of Rap during IVM. The potential underlying mechanism is that Rap can activate autophagy and upregulate the levels of E2 and HIF-1α in mature oocytes. Additionally, the levels of both E2 and HIF-1α are regulated by each other and involve Rap-regulated autophagy in oocytes. Full article

Hot in-place recycling (HIR) is a sustainable pavement rehabilitation method. However, it is susceptible to aging processes that can compromise its mechanical properties and long-term performance. This study investigates the effects of thermo-oxidative (TO) and ultraviolet (UV) aging on HIR mixtures. Basic performance tests were conducted on the aggregate gradation, moisture content, and asphalt content of the reclaimed asphalt pavement (RAP) to assess the aging level. Simulations of long-term and short-term oxidative aging of the HIR mixture, along with 12 months of UV irradiation, were performed to evaluate its high-temperature stability, low-temperature crack resistance, and water stability. The Verhulst model was employed to establish a predictive equation for performance attenuation under UV aging. To quantify the photoaging effect, indicators for UV aging degree were proposed to characterize the road performance of the HIR mixture, including the aging rate and the aging residual index. Results indicate that the improvement in high-temperature performance after aging is limited, but cracking resistance decreases substantially. Notably, the flexural tensile strain was reduced by 129.25 με for 10 years of TO aging compared to 12 months of UV exposure, underscoring the importance of considering environmental factors in performance predictions. This study emphasizes the need for enhanced aging mitigation strategies to improve the sustainability and reliability of HIR mixtures in practical applications. Full article

Great efforts have been made in recent years by the scientific community and the asphalt industry in developing sustainable technologies for the production of asphalt mixtures for road paving applications, pursuing the use of ever higher quantities of recycled materials. In this regard, the challenge is to define the optimal formulation of the mixture which allows the various component materials to be synergistically combined without compromising the performance and durability of the asphalt pavement. In such a context, the experimental study described in this paper aimed to provide a contribution to research by investigating sustainable asphalt mixtures containing 50% reclaimed asphalt pavement (RAP) and polymeric compound composed of 100% recycled plastics. A wide set of mixtures was prepared in a laboratory by employing different dosages of polymeric compound added via the hybrid method at various binder contents. For comparison purposes, an additional set of reference asphalt mixtures containing standard polymer-modified binder (PmB) and virgin aggregate without RAP was prepared and tested. The experimentation focused on the main engineering properties of the asphalt mixtures, including their workability, volumetric properties, and mechanical characteristics. The experimental study involved a preliminary trial phase to establish an appropriate laboratory mixing procedure. The results obtained from the experimentation indicated that recycled waste plastics have good potential for use in asphalt mixtures with high contents of RAP, provided that the quantity of added plastics is adequately balanced. Full article

To investigate the feasibility of composite modification techniques in improving the performance of recycled asphalt mixtures, in this study, the high-viscosity agent (HVA) and crumb-rubber materials (CRM) were used to modify asphalt with a styrene-butadiene-styrene block copolymer (SBS), in order to prepare SBS-HVA and SBS-CRM composite-modified asphalts. The virgin asphalt mixtures, as well as three asphalt types of recycled asphalt mixtures with 50% reclaimed asphalt pavement (RAP) content, were designed. The optimal asphalt content of the four types of asphalt mixtures was analyzed, and the rutting test, the asphalt bond strength test, the moisture-induced sensitivity test, and the low-temperature cracking resistance test were conducted to investigate the performance of the four types of asphalt mixtures. The results showed that the higher the asphalt kinematic viscosity, the higher the optimum asphalt content of the asphalt mixtures under the same air voids. HVA significantly improves the adhesion between SBS-modified asphalt and aggregate under dry conditions, while SBS-CRM composite-modified asphalt performs similarly to SBS-modified asphalt. Before and after water immersion, the degree of pull-out strength decay between the asphalts and aggregates follows the sequence of SBS-CRM- > SBS- > SBS-HVA-modified asphalts. Additionally, the residual pull-out work follows the sequence of SBS-HVA- > SBS-CRM- > SBS-modified asphalt. SBS-CRM composite-modified asphalt can significantly improve the moisture sensitivity of recycled asphalt mixtures, as well as low-temperature cracking resistance, while SBS-CRM composite-modified asphalt only improves the low-temperature cracking resistance of recycled asphalt mixtures, and does not improve the moisture sensitivity. Based on the results, it is recommended to select the appropriate composite modification method based on the climate and loading conditions, to maximize the value of asphalt, and to achieve sustainable and durable pavement. Full article

The substitution of virgin asphalt binder with reclaimed asphalt pavement (RAP) has environmental and economic merits, however, cracking susceptibility arises due to the aged asphalt binder within RAP. The objectives of this study are to (1) enhance the cracking resistance of asphalt mixtures containing 50% RAP utilizing recycling agents (RAs) derived from six petroleum-based and bio-based materials, (2) conduct an environmental impact assessment (represented by global warming potential “GWP”) for high-RAP mixtures including RAs, and (3) estimate the cost effectiveness of including high-RAP content in asphalt mixtures. Based on the RAP asphalt binder performance grade (PG), base asphalt binder PG, and RAP content, the RA contents were determined to achieve a target asphalt binder of PG 76-22. A control mixture was benchmarked for comparison, specified for high-traffic volume roads, and contained PG 76-22 polymer-modified asphalt binder. The engineering performance of studied asphalt mixtures was evaluated using the Hamburg wheel-tracking (HWT), semi-circular bend, Illinois flexibility index, Ideal cracking tolerance, and thermal stress-restrained specimen tensile strength tests. It was found that petroleum-derived aromatic oil, soy-based oil, and tall oil fatty acid-based RAs demonstrated a successful restoration of aged RAP asphalt binder without compromising the permanent deformation resistance. The 50% RAP mixtures emitted less GWP by 41% and 42.9% using petroleum- and bio-oil RAs, respectively, and achieved a 31% cost reduction compared to the control mixtures. Full article

Waste Cooking Oil (WCO), Soy Oil (SO), and Wastewater Sludge (WWS) have great potential to increase reclaimed asphalt pavement (RAP) content for economic and environmental benefits. This study explored the effects of SO and WCO on rutting, fatigue cracking, and low-temperature cracking performance of binders and Hot Mix Asphalt (HMA) with high RAP content. The potential effect of WWS on the performance and compaction efforts of high RAP content mixes at a 10 °C (50 °F) lower compaction temperature than the control compaction temperature was also investigated. The results indicated that 85% of the RAP binders can be incorporated while maintaining similar performance compared to the control by using 15% SO or 12.5% WCO as a rejuvenator with 2.5% virgin binder. Adding 1% WWS by weight of the total binder improved the binder’s rheological properties, the mix’s cracking performance, and the mix’s density at lower compaction temperatures. Full article