Search Results (267)

Maintaining the required relative humidity values in the vehicle cabin is an important HVAC task, along with considerations related to the temperature, velocity, air pressure and noise. Deviation from the optimal values worsens the psycho-physiological state of the driver and affects the energy efficiency of the train. In this study, a model of liquid film formation on and removal from various cabin surfaces was constructed using the fundamental Navier–Stokes hydrodynamic equations. A special transport model based on the liquid vapor diffusion equation was used to simulate the air environment inside the cabin. The evaporation and condensation of surface films were simulated using the Euler film model, which directly considers liquid–gas and gas–liquid transitions. Numerical results were obtained using the RANS equations and a turbulence model by means of the finite volume method in Ansys CFD. Conjugate fields of temperature, velocity and moisture concentration were constructed for various time intervals, and the dependence values for the film thicknesses on various surfaces relative to time were determined. The verification was conducted in comparison with the experimental data, based on the protocol for measuring the microclimate indicators in workplaces, as applied to the train cabin: the average ranges encompassed temperature changes from 11% to 18%, and relative humidity ranges from 16% to 26%. Comparison with the results of other studies, without considering the phase transition and condensation, shows that, for the warm mode, the average air temperature in the cabin with condensation is 12.5% lower than without condensation, which is related to the process of liquid evaporation from the heated walls. The difference in temperature values for the model with and without condensation ranged from −12.5% to +4.9%. We demonstrate that, with an effective mode of removing condensate film from the window surface, including recirculation modes, the energy consumption of the climate control system improves significantly, but this requires a more accurate consideration of thermodynamic parameters and relative humidity. Thus, considering the moisture condensation model reveals that this variable can significantly affect other parameters of the microclimate in cabins: in particular, the temperature. This means that it should be considered in the numerical modeling, along with the basic heat transfer equations. Full article

Rammed earth (RE), a traditional material aligned with circular economy (CE) principles, has been gaining renewed interest in contemporary construction due to its low environmental impact and compatibility with sustainable building strategies. Though not a modern invention, it is being reintroduced in response to the increasingly strict European Union (EU) regulations on carbon footprint, life cycle performance, and thermal efficiency. RE walls offer multiple benefits, including humidity regulation, thermal mass, plasticity, and structural strength. This study also draws attention to their often-overlooked ability to mitigate indoor overheating. To preserve these advantages while enhancing thermal performance, this study explores insulation strategies that maintain the vapor-permeable nature of RE walls. A parametric analysis using Delphin 6.1 software was conducted to simulate heat and moisture transfer in two main configurations: (a) a ventilated system insulated with mineral wool (MW), wood wool (WW), hemp shives (HS), and cellulose fiber (CF), protected by a jute mat wind barrier and finished with wooden cladding; (b) a closed system using MW and WW panels finished with lime plaster. In both cases, clay plaster was applied on the interior side. The results reveal distinct hygrothermal behavior among the insulation types and confirm the potential of natural, low-processed materials to support thermal comfort, moisture buffering, and the alignment with CE objectives in energy-efficient construction. Full article

A fully coupling nonlinear finite element algorithm for moisture and heat transfer is developed and implemented. The finite element model starts from a suitable formulation of the constitutive and equilibrium equations. The nonlinearity arises due to the strong moisture and temperature dependence of the material properties. Four examples are presented to check the validity and precision of the finite element model. Two of the examples compare the numerical results with simplified, one-dimensional analytical solutions. Perfect agreement is obtained between the analytical and numerical solutions. The results show that the dependency of the material coefficients on the moisture and temperature is important, even for one-dimensional cases. The other two examples, without direct analytical solution due to the material nonlinearity, show that the fully coupling between the moisture and heat conduction is essential. The formulation can be used for the transient analysis of moisture and heat conduction with arbitrary geometrical dimensions and time-dependent loading conditions. Full article

Prefabricated components inevitably generate numerous assembly joints during installation, with each 1 mm increase in joint width correlating to a 15–20% elevation in the annual occurrence frequency of the frost formation risk. In the Inner Mongolia Region, the water migration at wall connection interfaces during winter significantly exacerbates freeze–thaw damage due to persistent thermal gradients. A coupled heat–moisture transfer model incorporating gas–liquid–solid phase transitions was developed, with the liquid moisture content and temperature gradient as dual driving forces. A validation against internationally recognized BS EN 15026:2007 benchmark cases confirmed the model robustness. The prefabricated sandwich insulation walls reconstructed with region-specific volcanic ash materials underwent a comparative evaluation of temperature and relative humidity distributions under varied winter conditions. Furthermore, we analyze and assess the potential for freezing at connection points and identify the specific areas at risk. Synergistic effects between assembly gaps and indoor–outdoor environmental interactions on wall performance degradation were systematically assessed. The results indicated that, across all working conditions, both the temperature and relative humidity at each wall measurement point underwent periodic variations influenced by the outdoor environment. These fluctuations decreased in amplitude from the exterior to the interior, accompanied by a noticeable delay effect. Specifically, at Section 2, the wall temperatures at points B2–B8 were higher compared to those at A2–A8 of Section 1. The relative humidity gradient remained relatively stable at each measurement point, while the temperature fluctuation amplitude was smaller by 2.58 ± 0.3 °C compared to Section 1. Under subfreezing conditions, Section 1 demonstrates a marked reduction in relative humidity (Cases 1-3 and 2-3) compared to reference cases, which is indicative of internal ice crystallization. Conversely, Section 2 maintains higher relative humidity values under identical therma. These findings suggest that prefabricated building joints significantly impact indoor and outdoor wall temperatures, potentially increasing the indoor heat loss and accelerating temperature transfer during winter. Full article

This study explores how production technology influences spray-applied rigid polyurethane (PUR) foam insulation’s cryogenic performance. In cryogenic applications such as liquid gas storage, insulation must minimise heat transfer and resist moisture ingress under severe thermal gradients. Experimental aluminium vessels were insulated with PUR foam of varying thicknesses and surface conditions—rough, machined smooth, and with a urea-based protective coating—and then tested using dynamic boil-off of liquid nitrogen (LN₂). Foam properties, including adhesion, mechanical strength, thermal expansion, thermal conductivity, and closed-cell content, were evaluated. The results revealed that thicker insulation reduced both effective thermal conductivity and moisture uptake. Although the urea-coated vessel showed minimal water absorption, the coating increased overall thermal conductivity due to its heat conduction and condensation behaviour. Moisture was primarily absorbed near the foam surface, and no cumulative effects were observed during repeated tests. The effective thermal conductivity was determined by interpolating boil-off data, confirming that insulation performance strongly depends on thickness, surface condition, and environmental humidity. These findings provide valuable guidance for the design and application of PUR foam insulation in cryogenic environments. Full article

As global mineral resources at shallow depths continue to deplete, thermal hazards have emerged as a critical challenge in deep mining operations. Conventional localized cooling systems suffer from a fundamental inefficiency where their cooling capacity is rapidly dissipated by the main ventilation airstream. This study introduces the innovative concept of a “microclimatic circulation zone” implemented through a convection–radiation cooling system. The design incorporates a synergistic arrangement of dual fans and flow-guiding baffles that creates a semi-enclosed air circulation field surrounding the modular convection–radiation cooling apparatus, effectively preventing cooling capacity loss to the primary ventilation flow. The research develops comprehensive theoretical models characterizing both internal and external heat transfer mechanisms of the modular convection–radiation cooling system. Using Fluent computational fluid dynamics software, we constructed an integrated heat–moisture–flow coupled numerical model that identified optimal operating parameters: refrigerant velocity of 0.2 m/s, inlet airflow velocity of 0.45 m/s, and outlet aperture height of 70 mm. Performance evaluation conducted at a mining operation in Yunnan Province utilized the Wet Bulb Globe Temperature (WBGT) index as the assessment criterion. Results demonstrate that the enhanced microclimatic circulation system exhibits superior cooling retention capabilities, with a 19.83% increase in refrigeration power and merely 3% cooling capacity dissipation at a 7 m distance, compared to 19.23% in the conventional system. Thermal field analysis confirms that the improved configuration successfully establishes a stable microclimatic circulation zone with significantly more concentrated low-temperature regions. This effectively addresses the principal limitation of conventional systems where conditioned air is readily dispersed by the main ventilation current. The approach presented offers a novel technological pathway for localized thermal environment management in deep mining operations affected by heat stress conditions. Full article

Freeze–thaw (F/T) technology is an environmentally friendly and efficient method for residual sludge treatment. This study investigates the enhancement of sludge dewatering performance through the addition of straw during F/T cycles. A mathematical model was established using the Box–Behnken central composite design and validated via COMSOL Multiphysics simulations. The optimal conditions were identified as freezing at −16 °C for 24 h, with 12.5 freeze–thaw cycles and a straw mixing ratio of 20%, reducing the sludge moisture content from 62.7% to 35.9%. The specific resistance to filtration (SRF) and cake moisture content decreased significantly with increasing straw addition, reaching a minimum SRF of 1.30 × 10¹² m/kg at the optimal straw ratio. Straw conditioning also intensified the combustion stage of the sludge by increasing the maximum weight loss rate and elevating the thermal decomposition temperature. Numerical simulations confirmed the experimental results, demonstrating that straw addition significantly improves sludge dewaterability by modifying heat and mass transfer mechanisms. Full article

Heat storage in compacted soil embankments is a promising technology in energy geotechnics, but its impact on the thermo-hydraulic behavior of unsaturated soils remains insufficiently understood. This paper investigates coupled heat and moisture transfer in unsaturated soil under different thermal conditions using a new bottom-heating method. The thermo-hydraulic response is monitored along the soil column and compared to an isothermal drying test. Variations in suction and water content were analyzed to determine water retention curve and to derive unsaturated hydraulic conductivity using the instantaneous profile method. The water retention curve exhibited deviations under thermal conditions, with reduced water contents observed only at intermediate suctions. Unsaturated hydraulic conductivity decreased significantly at moderate suctions but increased by up to one order of magnitude at high suctions. Heat-driven moisture redistribution was examined through flux calculations, highlighting that vapor-phase transport contributed significantly, up to 88%, to the upward water migration. These findings contribute to a better understanding of thermo-hydraulic interactions in unsaturated soils, which is essential for optimizing thermal storage applications in compacted embankments. Full article

A vital procedure for eliminating moisture from the air, dehumidification is necessary for processes like desalination and air conditioning. The Peltier dehumidifier, sometimes referred to as a thermoelectric dehumidifier, removes moisture using the Peltier effect to generate a temperature differential across a Peltier module. Nevertheless, inadequate heat removal from the hot side of the module and a low coefficient of performance (COP) are common problems with Peltier-based dehumidifiers. By combining baffles or turbulators with Peltier plates to increase heat transfer rates, this study overcomes these drawbacks and raises the dehumidifier’s COP and thermal enhancement factor (TEF). On the hot side of the Peltier module, airfoil-shaped baffles are used in the experimental setup to enhance heat dissipation and speed up turbulence. Performance significantly improved, as evidenced by the findings, with the TEF rising to 3.2. Furthermore, the COP improved from 0.06 to 0.45, and the water condensation rate rose to a high of 35 mL per hour. These improvements are ascribed to the higher heat transfer rates made possible by the baffles, which enable the more effective cooling of the Peltier module’s cold side. This study demonstrates how turbulators can increase Peltier-based dehumidifiers’ effectiveness and make them more practical for industrial settings, especially in areas with limited water supplies. According to the results, thermoelectric dehumidification systems can function much better overall if heat transmission on the Peltier module’s hot side is optimized. Full article

This study investigates the coupled hygrothermal behavior of mycelium-based composites (MBCs) as a function of their microstructural organization, governed by fungal species, substrate type, additive incorporation, and treatment method. Eleven composite formulations were selected and characterized using a multi-scale experimental approach, combining scanning electron microscopy, dynamic vapor sorption, vapor permeability tests, capillary uptake measurements, and transient thermal conductivity analysis. SEM analysis revealed that Ganoderma lucidum forms dense and interconnected hyphal networks, whereas Trametes versicolor generates looser, localized structures. These morphological differences directly influence water vapor transport and heat conduction. Additive-enriched composites exhibited up to 21.8% higher moisture uptake at 90% RH, while straw-based composites demonstrated higher capillary uptake and free water saturation (up to 704 kg/m³), indicating enhanced moisture sensitivity. In contrast, hemp-based formulations with Ganoderma lucidum showed reduced sorption and vapor permeability due to limited pore interconnectivity. Thermal conductivity varied nonlinearly with temperature and moisture content. Fitting the experimental data with an exponential model revealed a moisture sensitivity coefficient thirty times lower for GHOP compared to VHOP, highlighting the stabilizing effect of a compact microstructure. The distinction between total and effective porosity emerged as a key factor in explaining discrepancies between apparent and functional moisture behavior. These findings demonstrate that hygric and thermal properties in MBCs are governed not by porosity alone, but by the geometry and connectivity of the internal fungal network. Optimizing these structural features enables fine control overheat and mass transfer, laying the groundwork for the development of high-performance, bio-based insulation materials. Full article

Energy recovery ventilators are essential for reducing building energy consumption, with the dynamic variation in their efficiency being a significant area of current research. To quickly analyze the parameters affecting the dynamic changes in energy recovery efficiency, this study develops a mathematical model for heat and moisture transfer. The model was validated through computational fluid dynamics (CFD) simulations and experimental data. The validation results showed that the discrepancies between the model’s sensible heat and enthalpy efficiencies and the experimental data were approximately 4%, while the error range for sensible heat efficiency compared to CFD simulations was between 3% and 7%. This model was used to evaluate various factors affecting energy recovery efficiency. The findings show that outdoor temperature and relative humidity have little effect on sensible heat efficiency, whereas latent heat efficiency increases with rising outdoor temperature and humidity. Both sensible and latent heat efficiency improve as airflow decreases, with latent heat efficiency being more sensitive to changes in airflow. Additionally, due to the very thin heat exchanger membrane, the mass diffusion coefficient has a more significant effect on efficiency than the thermal conductivity coefficient. In conclusion, energy recovery efficiency is dynamic, and the proposed model provides rapid predictions of how influencing factors affect the efficiency. Full article

Moisture phase change (MPC), a key process in bread baking, significantly impacts heat and mass transfer, as confirmed by experiments. However, existing models poorly characterize this phenomenon, and its quantitative impact on baking needs systematic study. This research develops a coupled multiphase model for heat and mass transfer with large deformation, employing both equilibrium and nonequilibrium approaches to describe MPC in closed and open pores, respectively. Experimentally calibrated pore-opening functions and viscosity variations revealed that pore-opening primarily occurs at 71–81 °C, whereas dough solidification occurs at 50–110 °C. Model-based analysis indicates that in closed pores, evaporation–diffusion–condensation is the primary mode of moisture transport and heat transfer with contributing approximately 60% of the total effective thermal conductivity, and when pores open, water vapor evaporates or condenses on pore walls, forming an ‘evaporation front’ and ‘condensation front’. The content of liquid water increases at the ‘condensation front’ and decreases at the ‘evaporation front’. Bread deformation is predominantly governed by pressure differentials between closed pores and the ambient environment, with the partial pressure of water vapor emerging as the principal driver because its average content exceeds 70% within closed pores. These findings demonstrate that MPC governs heat and mass transfer and deformation during bread baking. Full article

In a plant factory, maintaining proper and uniform air/moisture movement above the crop canopy is crucial for aiding plant growth. This research has utilized a three-dimensional computation model to investigate airflow and heat transfer in a plant factory, where airflow, heat, and humidity distributions above plant crops were calculated concerning five categories of crop planting density (P_d) and air change rate (ACH) in the crop area. Spatial uniformities of airflow velocity, temperature, and relative humidity immediately above the crops are evaluated using the objective uniformity parameter (OU), relative standard deviation of temperature (RSD_T) and relative standard deviation of relative humidity (RSD_RH), respectively. Furthermore, a factor of effectiveness (θ) is defined, depending on the uniformity of velocity, temperature, and relative humidity distribution, to comprehensively evaluate the impact of various ACH with P_d on overall effectiveness. Full numerical results show that air velocity, temperature, and relative humidity above the crops are notably influenced by P_d and ACH. As ACH increases, the OU of the air above the indoor crop also expands. Moreover, higher OU values are observed for smaller crop P_d. However, excessively small crop area planting densities and excessively large ACH do not result in a higher OU for the air above the crop. As ACH increases, both RSD_T and RSD_RH decay for the whole range of crop P_d. Moreover, smaller P_d values could achieve the uniformity of thermal fields, while having minimal effects on the relative humidity distributions. Generally, increasing ACH and decreasing P_d could enhance overall value of θ. However, excessively increasing ACH and decreasing P_d does not have a significant effect on θ, which is jointly influenced by OU, RSD_T, and RSD_RH. Therefore, a more suitable combination of ACH and P_d is urgently required to improve the design of agricultural system to enhance crop microclimate uniformity for optimal plant growth and productivity. Full article

Soil gravel–sand mulching—an ancient farming method in arid areas—is used to cope with drought by conserving water and improving soil temperature, the latter being a key factor affecting agricultural production. The objective of this study is to ascertain the influence of soil water content and meteorological elements on soil temperature under gravel–sand mulching conditions. Field experiments, analysis of variance, Pearson correlation analysis, and other statistical methods were used to study the effects of varying soil moisture content on soil temperature at 0–25 cm depth under gravel–sand mulching conditions, and to analyze the relationships between meteorological factors and soil temperature during the temperature measurement period. In the 0–20 cm soil layer, the soil accumulated temperature decreased with an increase in soil moisture content, while the change rate of temperature increased. In the test range, the temperature conductivity of 10–15 cm soil increased with the increase in soil water content in the 20–40 cm layer. Under gravel–sand mulching conditions, soil temperature was not only related to air temperature but also positively related to water vapor pressure. When the soil moisture content was high, the soil temperature decreased with an increase in atmospheric evaporation capacity. When the soil moisture conditions were poor, the meteorological factors had an effect of increasing the soil temperature. Under gravel–sand mulching conditions, soil moisture content exhibits a significant negative correlation with both soil temperature and accumulated temperature. Higher soil moisture enhances vertical heat conduction, facilitating heat transfer from the surface to deeper layers. The 10–15 cm soil layer acts as a thermal buffer zone, regulating temperature fluctuations and mitigating extreme heat variations. However, higher air temperature leads to greater heat accumulation, while, in wetter soils, enhanced heat conduction and evaporative cooling lower soil temperature. Full article

Due to moisture migration effects, thermal and moisture bridges tend to form at building joints, thereby increasing the thermal conductivity coefficient of construction materials. To examine the influence of moisture transfer on the thermal performance of ‘one-line’ vertical joint walls, this study establishes a thermal–humidity coupling numerical model at the vertical joint of sandwich insulation composite walls. This model is employed to analyze the effects of various joint filling materials (aerated blocks, glass wool, concrete), insulation layer thicknesses, and environmental conditions on the thermal transfer properties of the wall joint. The results indicate that when filled with aerated blocks, the joint is most significantly affected by moisture transfer, exhibiting a heat flow loss rate of 8.08%. In high-temperature environments, the thermal transfer performance at the connection of the composite wall is particularly susceptible to humidity, with heat flow loss rates ranging from 6.17% to 8.74%. Furthermore, an increase in the thickness of the insulation layer leads to a reduction in the “heterogeneity” of the sandwich insulation wall, which reduces the wall’s effects to moisture transfer; however, this is accompanied by a rise in the heat loss rate at the connection. After accounting for the effects of hygrothermal bridging, the mean heat transfer corrected coefficient of the wall in areas with hot summers and cold winters ranges from 1.10 to 1.18 during the summer and from 1.12 to 1.16 during the winter. This finding holds significant relevance for aiding researchers in predicting thermal transfer analysis in scenarios involving wall moisture transfer. Full article