Search Results (60)

Emerging sustainability demands and calls for lowering materials’ environmental impact have directed authors to examine a class of polymers characterised as covalent adaptable networks and referred to as vitrimers. In this study, composite plates were made using vitrimer resin as the matrix material and continuous unidirectional flax fibre fabrics as the reinforcement. A specific early-stage composite part production method is proposed to make the multi-ply flax/vitrimer composite plate. The development of natural fibre–reinforced vitrimer composites is of clear research interest as a promising approach towards sustainable and recyclable novel material systems. Specimens prepared with all the plies oriented 0° exhibited a 129.4 MPa tensile strength and a 12.4 GPa tensile modulus, indicating a 334% increase in tensile strength when compared to the average value of 29.8 MPa obtained for neat vitrimer specimens and a 1140% improvement in the tensile modulus compared to the 1.0 GPa reached for neat vitrimer. The specimens whose plies were oriented 90° are found to deliver a tensile strength of 12.2 MPa and a 1.3 GPa tensile modulus. Applying the classical composite material micromechanics equation to calculate the 0°-direction tensile modulus demonstrated a good agreement with the experimentally obtained value—a 9.6% difference was discovered. Proper fibre/matrix interfacial adhesion was detected when the flax/vitrimer specimens’ surfaces after fracture were examined under scanning electron microscope. The research findings on tensile mechanical properties reveal that the observed flax/vitrimer composites may be potential candidates for replacing typical synthetic fibre–reinforced materials rated for automotive applications and intended for in-plane loaded parts, particularly some inner-body vehicle elements. Full article

This study investigates the mechanical, structural, and thermal performance of bio-based composite laminates reinforced with nonwoven fibrous materials derived from polylactic acid (PLA), poly(butylene succinate) (PBS), and polyamide 1010 (PA1010). The fibrous reinforcements, produced using melt-blown and electrospinning techniques, were characterized in terms of morphology, fibre diameter distribution, and wettability, and subsequently incorporated into bio-resin laminates to strengthen them. The curing behaviour of the composites was evaluated using differential scanning calorimetry (DSC). The results demonstrate that fibre structure and morphology strongly influence resin impregnation and interfacial interactions. Mechanical properties varied significantly depending on the reinforcement type. PA1010-based laminates exhibited the highest strength and stiffness due to their compact and uniform fibrous structure. PBS-based systems showed intermediate behaviour, while PLA-based composites displayed lower strength but higher deformability. DSC results indicated that fibre type affected crosslinking efficiency. Thermogravimetric analysis (TGA) revealed similar initial thermal stability of laminates (T₅% ≈ 299–313 °C), governed by the resin matrix, while differences at higher temperatures reflected the type of reinforcement used. These findings highlight the importance of fibre morphology and interfacial compatibility in designing sustainable composite laminates reinforced with recycled fibrous materials. Full article

Recycled carbon fibres frequently exhibit degraded surface functionality owing to prior matrix removal processes, limiting their compatibility with contemporary epoxy resin systems. This study proposes a nanobubble-based surface treatment route designed to restore and enhance the surface characteristics of recycled carbon fibres without aggressive chemical oxidation. The study generated ozone and carbon dioxide nanobubbles in aqueous media and experimentally investigated the effects of nanobubble treatment on the surface properties and adhesive behaviour of recycled carbon fibres. Surface chemical changes were examined using X-ray photoelectron spectroscopy, which revealed an increase in oxygen-containing functional groups due to the nanobubble treatment, indicating improved surface polarity and potential for chemical interaction with epoxy networks. The practical effectiveness of the treatment was assessed via a pinhole pull-out test that served as an indirect measure of interfacial adhesion with epoxy resin, especially the combination of ozone nanobubbles and recycled carbon fibres. Notably, the nanobubble-treated recycled carbon fibres exhibited an increase in the adhesion compared with untreated recycled carbon fibres, rising from 84.5 ± 11.5 MPa to 138.5 ± 14.8 MPa, reflecting enhanced wetting behaviour and stronger fibre–matrix interfacial bonding. Overall, the proposed nanobubble processing route offers a mild, scalable, and environmentally favourable method for restoring surface reactivity in recycled carbon fibres, supporting their reintegration into high-performance composite applications. Full article

This research investigates the effects of corona plasma treatment on the mechanical properties of jute/epoxy-reinforced composites, particularly within biomedical application contexts. Plant Fibre Composites (PFCs) are attractive for medical devices and scaffolds due to their environmental friendliness, renewability, cost-effectiveness, low density, and high specific strength. However, their applications are often constrained by inferior mechanical performance arising from poor bonding between the plant fibre used as the reinforcement and the synthetic resin or polymer serving as the matrix. This study addresses the challenge of improving the weak interfacial bonding between plant fibre and synthetic resin in a 2/2 twill-weave-woven jute/epoxy composite material. The surface of the jute fibre is modified for better adhesion with the epoxy resin through plasma treatment, which exposes the jute fibre to controlled plasma energy and utilises dry air (plasma only), argon (Ar) (argon gas with plasma), and nitrogen (N₂) (nitrogen gas with plasma) at two different distances (25 mm and 35 mm) between the plasma nozzle and the fibre surface. In this context, “equilibrium” refers to the optimal combination of plasma power, treatment distance, and gas environment that collectively determines the degree of fibre surface modification. The results indicate that all plasma treatments improve the interlaminar shear strength in comparison to untreated samples, with treatments at 35 mm using N₂ gas showing a 35.4% increase in shear strength. Conversely, plasma treatment using dry air at 25 mm yields an 18.3% increase in tensile strength and a 35.7% increase in Young’s modulus. These findings highlight the importance of achieving an appropriate equilibrium among plasma intensity, treatment distance, and fibre–plasma interaction conditions to maximise the effectiveness of plasma treatment for jute/epoxy composites. This research advances sustainable innovation in biomedical materials, underscoring the potential for improved mechanical properties in environmentally friendly fibre-reinforced composites. Full article

Oxidation can lead to intrinsic degradation and loss in the load-bearing capacity of ceramic matrix composites (CMCs) in high-temperature service, thereby compromising structural integrity and operational safety. To elucidate the mechanism of its oxidation effects, this study predicted the oxygen diffusion coefficient within 2.5D woven C/SiC fibre bundles based on gas diffusion and oxidation kinetics theory, and subsequently constructed a meso-scale constitutive model incorporating oxidation damage and fibre defect distribution. Furthermore, a micro-scale framework for yarns was established by integrating interfacial slip behaviour, and an RVE model for 2.5D woven C/SiC was constructed based on X-ray computed tomography reconstruction of the actual microstructure. Building upon this foundation, an oxidation constitutive model applicable to loading–unloading cycles was proposed and validated through high-temperature oxidation tests at 700 °C, 900 °C, and 1100 °C. Results demonstrate that this model effectively characterizes the strength degradation and stiffness reduction caused by oxidation, enabling prediction of CMCs’ mechanical properties under oxidizing conditions and providing a physics-based foundation for the reliable design and life assessment of C/SiC components operating in oxidizing environments. Full article

Composite materials are increasingly required to operate in cryogenic environments, including liquid hydrogen and oxygen storage, deep-space structures, and polar infrastructures, where long-term strength, toughness, and reliability are essential. This review provides a unique contribution by systematically integrating recent advances in understanding cryogenic behaviour into a unified multi-scale framework. This framework synthesises four critical and interconnected aspects: constituent response, composite performance, enhancement mechanisms, and modelling strategies. At the constituent level, fibres retain stiffness, polymer matrices stiffen but embrittle, and nanoparticles offer tunable thermal and mechanical functions, which collectively define the system-level performance where thermal expansion mismatch, matrix embrittlement, and interfacial degradation dominate failure. The review further details toughening strategies achieved through nano-addition, hybrid fibre architectures, and thin-ply laminates. Modelling strategies, from molecular dynamics to multiscale finite element analysis, are discussed as predictive tools that link these scales, supported by the critical need for in situ experimental validation. The primary objective of this synthesis is to establish a coherent perspective that bridges fundamental material behaviour to structural reliability. Despite these advances, remaining challenges include consistent property characterisation at low temperature, physics-informed interface and damage models, and standardised testing protocols. Future progress will depend on integrated frameworks linking high-fidelity data, cross-scale modelling, and validation to enable safe deployment of next-generation cryogenic composites. Full article

Short fibre-reinforced adhesives (SFRAs) are increasingly used in wind turbine blades to enhance stiffness and fatigue resistance, yet their heterogeneous microstructure poses significant challenges for predictive modelling. This study presents a fully automated digital workflow that integrates micro-computed tomography (µCT), image processing, and finite element modelling (FEM) to investigate the mechanical response of SFRAs. Our aim is also to establish a computational foundation for data-driven modelling and future AI surrogates of adhesive joints in wind turbine blades. High-resolution µCT scans were denoised and segmented using a hybrid non-local means and Gaussian filtering pipeline combined with Otsu thresholding and convex hull separation, enabling robust fibre identification and orientation analysis. Two complementary modelling strategies were employed: (i) 2D slice-based FEM models to rapidly assess microstructural effects on stress localisation and (ii) 3D voxel-based FEM models to capture the full anisotropic fibre network. Linear elastic simulations were conducted under inhomogeneous uniaxial extension and torsional loading, revealing interfacial stress hotspots at fibre tips and narrow ligaments. Fibre clustering and alignment strongly influenced stress partitioning between fibres and the matrix, while isotropic regions exhibited diffuse, matrix-dominated load transfer. The results demonstrate that image-based FEM provides a powerful route for structure–property modelling of SFRAs and establish a scalable foundation for digital twin development, reliability assessment, and integration with physics-informed surrogate modelling frameworks. Full article

This study evaluates the effect of chemical treatments on the short-beam shear strength, vibrational, and acoustic performance of banana-fibre-reinforced carbon–Kevlar hybrid composites. Banana fibres were treated with 5% NaOH and 0.5% KMnO₄ to improve fibre surface characteristics and interfacial bonding within a sandwich laminate of carbon–Kevlar intraply skins and banana fibre core fabricated by hand lay-up and compression moulding. Short-beam shear strength (SBSS) increased from 14.27 MPa in untreated composites to 17.65 MPa and 19.52 MPa with KMnO₄ and NaOH treatments, respectively, due to enhanced fibrematrix adhesion and removal of surface impurities. Vibrational analysis showed untreated composites had low stiffness (7780.23 N/m) and damping ratio (0.00716), whereas NaOH treatment increased stiffness (9480.51 N/m) and natural frequency (28.68 Hz), improving rigidity and moderate damping. KMnO₄ treatment yielded the highest damping ratio (0.0557) with reduced stiffness, favouring vibration energy dissipation. Acoustic tests revealed KMnO₄-treated composites have superior sound transmission loss across low to middle frequencies, peaking at 15.6 dB at 63 Hz, indicating effective acoustic insulation linked to better mechanical damping. Scanning electron microscopy confirmed enhanced fibre impregnation and fewer defects after treatments. These findings highlight the significant role of chemical surface modification in optimising structural integrity, vibration control, and acoustic insulation in sustainable banana fibre/carbon–Kevlar hybrids. The improved multifunctional properties suggest promising applications in aerospace, automotive, and structural fields requiring lightweight, durable, and sound-mitigating materials. Full article

Poly(lactic acid) (PLA) and poly(ether-ether ketone) (PEEK) are widely recognized for their biocompatibility and processability in orthopaedic applications. However, PLA suffers from brittleness and limited thermal and mechanical stability, while PEEK, despite its better strength, does not fully replicate the mechanical and tribological performance of natural bone. This study explores the enhancement of structural and tribological properties in PLA- and PEEK-based composites reinforced with short glass fibres (S-GF) via additive manufacturing. Microstructural analysis confirms uniform GF dispersion within both polymer matrices, with no evidence of agglomeration, fibre pull-out, or interfacial debonding, suggesting strong fibre–matrix adhesion. The incorporation of GF significantly improved mechanical performance: microhardness increased by 38.3% in PLA and 36.3% in PEEK composites, while tensile strength increased by 25.1% and 13.4%, respectively, compared to plain polymers. These enhancements are attributed to effective stress transfer enabled by uniform fibre distribution and strong interfacial bonding. Tribological tests further demonstrate enhanced wear resistance, reduce damage propagation, and improved surface integrity under micro-scratching. These findings highlight the potential of GF-reinforced PLA and PEEK composites as high-performance materials for load-bearing biomedical applications, offering a balanced combination of mechanical strength and wear resistance aligned with the functional requirements of bioimplants. Full article

In this study, the influences of natural fibres (sugarcane bagasse (SB) and sawdust (SD)) on the material properties of polybutylene succinate (PBS) prepared through melt compounding were investigated. The study further evaluated the effects of incorporating halloysite nanotubes (HS) and expandable graphite (EG) on the properties of PBS/SD and PBS/SB binary and PBS/SB/SD hybrid composites. The morphological analysis indicated poor interfacial adhesion between PBS and the fibres. The obtained findings indicated enhancements in the complex viscosity of PBS in the presence of natural fibres, and further improvements in the presence of HS and EG. The stiffness of PBS hybrid composites also increased upon the addition of HS and EG. Moreover, the crystallization temperatures of PBS increased in the presence of fillers, with EG showing better nucleation efficiency. However, the mechanical properties (toughness and impact resilience) decreased due to the increased stiffness of the composites and the poor interfacial adhesion between the matrix and the fillers, indicating the need to pre-treat the fibres to enhance compatibility. Overall, the material properties of PBS/SD/SB hybrid composites were enhanced by incorporating HS and EG at low concentrations. Full article

This research paper employed novel sustainable alternative materials to reduce the environmental impact of thermoset/synthetic fibre composites. The effect of seawater hydrothermal ageing at 45 °C for 45 and 90 days on the physical and interlaminar fracture toughness (mode I and mode II) of a semi-unidirectional non-crimp basalt fibre (BF)-reinforced acrylic matrix and epoxy matrix composites was investigated. Optical and scanning electron microscopes were used to describe the fracture and interfacial failure mechanisms. The results show that the BF/Elium composite exhibited higher fracture toughness properties compared to the BF/Epoxy composite. The results of the mode I and mode II interlaminar fracture toughness values for the BF/Elium composite were 1280 J/m² and 2100 J/m², which are 14% and 56% higher, respectively, than those of the BF/Epoxy composite. The result values for both composites were normalised with respect to the density of each composite laminate. The saturated moisture content and diffusion coefficient values of seawater-aged samples at 45 °C and room temperature for the BF/Elium and BF/Epoxy composites were analysed. Both composites exhibited signs of polymer matrix decomposition and fibre surface degradation under the influence of seawater hydrothermal ageing, resulting in a reduction in the mode II interlaminar fracture toughness values. Enhancement was observed in mode I fracture toughness under hydrothermal ageing, particularly for the BF/Epoxy composite, due to matrix plasticisation and fibre bridging. Full article

In the present study, a programme of experimental investigations was carried out to examine the direct uniaxial tensile (and pull-out) behaviour of plain and fibre-reinforced lightweight aggregate concrete. The lightweight aggregates were recycled from fly ash waste, also known as Pulverised Fuel Ash (PFA), which is a by-product of coal-fired electricity power stations. Steel fibres were used with different aspect ratios and hooked ends with single, double and triple bends corresponding to 3D, 4D and 5D types of DRAMIX steel fibres, respectively. Key parameters such as the concrete compressive strength f_lck, fibre volume fraction V_f, number of bends n_b, embedded length L_E and inclination angle ϴ_f were considered. The fibres were added at volume fractions V_f of 1% and 2% to cover the practical range, and a direct tensile test was carried out using a purpose-built pull-out test developed as part of the present study. Thus, the tensile mechanical properties were established, and a generic constitutive tensile stress–crack width σ-ω model for both plain and fibrous lightweight concrete was created and validated against experimental data from the present study and from previous research found in the literature (including RILEM uniaxial tests) involving different types of lightweight aggregates, concrete strengths and steel fibres. It was concluded that the higher the number of bends n_b and the higher the volume fraction V_f and concrete strength f_lck, the stronger the fibre–matrix interfacial bond and thus the more pronounced the enhancement provided by the fibres to the uniaxial tensile residual strength and ductility in the form of work and fracture energy. A fibre optimisation study was also carried out, and design recommendations are provided. Full article

This study explores the mechanical behaviour of intra-laminar hybrid flax/E-glass composites, focusing on the role of micro-scale irregularities in flax fibres. By employing computational micromechanics and Monte Carlo simulations, it analyses the influence of flax fibre geometry and elastic properties on the performance of hybrid and non-hybrid composites. A Non-Circular Fibre Distribution (NCFD) algorithm is introduced to generate microstructures with randomly distributed non-circular flax and circular E-glass fibres, which are then modelled using a 3D representative volume element (RVE) model developed in Python 2.7 and implemented with Abaqus/Standard. The RVE dimensions were specified as ten times the mean characteristic length of flax fibres (580 μm) for the width and length, while the thickness was defined as one-tenth the radius of the E-glass fibre. Results show that Monte Carlo simulations accurately estimate the effect of fibre variabilities on homogenised elastic constants when compared to measured values and Halpin-Tsai predictions, and they effectively evaluate the fibre/matrix interfacial stresses and von Mises matrix stresses. While these variabilities minimally affect the homogenised properties, they increase the presence of highly stressed regions, especially at the interface and matrix of flax/epoxy composites. Additionally, intra-laminar hybridisation further increases local stress in these critical areas. These findings improve our understanding of the relationship between the natural fibre shape and mechanical performance in flax/E-glass composites, providing valuable insights for designing and optimising advanced composite materials to avoid or delay damage, such as matrix cracking and splitting, under higher applied loads. Full article

This study investigates the quasi-static and viscoelastic properties of additively manufactured (AM) PETG reinforced with short carbon fibres. Samples were manufactured using different parameters in terms of the infill pattern, porosity, and annealing condition. Tensile and compressive tests were conducted to determine quasi-static properties such as Young’s modulus and toughness, and dynamic mechanical analysis was used under a frequency sweep of 1–100 Hz to describe the viscoelastic behaviour of the composites. The major impacts and responses between the print parameters were quantified using Analyses of Variance (ANOVAs), which revealed the major contributor to each mechanical property. Fractography on the tensile samples using scanning electron microscopy demonstrated fibre pull-out, indicating poor fibre–matrix bonding, but also revealed interfacial bonding between raster lines in the annealed samples. This had a prominent effect on the properties of latitudinal samples where the force applied was perpendicular to the raster lines. Generally, porosity appeared to have the greatest contribution to the variance in the mechanical properties, with the exception of the tensile modulus, where the infill pattern had a more substantial effect. Annealing caused a consistent increase in the tensile modulus of the tested samples, which can be used to support the design and optimisation of AM parts when they are used under specific loading conditions. Full article