Search Results (125)

We developed a multi-channel and multilayered polydimethylsiloxane (PDMS) microfluidic platform that integrates cyclic mechanical stimulation, independent reagent delivery, and real-time optical observation within a single device. The platform employs a four-layer architecture comprising a pneumatic valve control layer, an observation channel for cell culture and imaging (24 mm × 4 mm), a medium perfusion layer with independent inlet ports, and a vacuum actuation layer that deforms a 200 μm PDMS membrane under −20 kPa cyclic pressure at 1 Hz. Cyclic membrane strain of 10% was calibrated using fluorescent bead tracking and image analysis. Finite element analysis based on nonlinear Föppl–von Kármán plate theory confirmed that the central cell culture region (60% of membrane area) exhibits a mean von Mises strain of 14.2% with a uniformity of 81.3% (CV = 18.7%), validating relatively uniform mechanical stimulation across the culture surface. As a proof-of-concept, human aortic smooth muscle cells (CRL-1999) cultured under cyclic strain showed significant upregulation of HIF-1$\alpha$ expression (2.5-fold, $p<0.01$) and pronounced F-actin stress fiber alignment visualized by fluorescence microscopy, confirming the platform’s capability for mechanotransduction studies and real-time cellular observation. The multi-channel architecture enables multi-condition parallel testing by simultaneously introducing different reagent concentrations through independent inlet ports while maintaining identical mechanical parameters across all channels, providing a versatile tool for systematic investigation of cellular responses under controlled biomechanical conditions. Full article

Self-oscillators convert constant external stimuli into sustained mechanical work, offering potential for applications such as soft robotics, energy absorption, and mechanical logic. However, the effective design of a light-driven self-oscillation system is challenging due to geometrically constrained deformation modes and the inherent rigidity of rectilinear light propagation paths. Notably, the mirror-reflected optical feedback loop decouples the feedback mechanism from geometric constraints imposed by deformation modes, enabling dynamic coupling independent of structural geometry. In this study, we introduce a geometry-flexible light feedback loop to drive a liquid crystal elastomer (LCE) self-oscillator. The system comprises an optically responsive LCE fiber, a spring, a mirror, and a perforated plate. By integrating the dynamic photon propagation path in light feedback routing with the dynamic deformation model of the LCE, we develop a dynamic theoretical model of the oscillator under constant illumination. Numerical simulations reveal two distinct patterns: static equilibrium and self-oscillation. Self-oscillation is generated by the light-induced contraction of LCE fiber segments illuminated by reflected light. Crucially, mirror-reflected light enables localized deformations anywhere along the fiber to contribute to global displacement feedback, thereby transcending the constraints of geometric deformation modes. This capability transcends the limitations posed by constrained geometric deformation modes, enabling adaptable control of the optical feedback loop through simple geometric alterations. This innovative approach circumvents the need for intricate structural feedback designs and separate energy harvesters, as well as actuator systems. Full article

Percentage depth–dose (PDD) distributions are fundamental to characterizing radiation beams in radiotherapy. This review provides an overview of both methods and sensor technologies for measuring PDD in photon, electron, proton, and carbon-ion beams. We summarize conventional dosimetry techniques, including water-phantom scanning with ionization chambers (cylindrical and parallel-plate) and radiochromic film, and discuss their strengths (established accuracy, calibration traceability) and limitations (volume averaging, delayed readout). We then examine emerging sensor technologies designed to improve spatial resolution, speed, and radiation hardness: multi-layer ionization chambers and Faraday cups for one-shot PDD acquisition; scintillator-based detectors (liquid, plastic, and fiber-optic) enabling real-time and high-resolution depth–dose measurements; advanced semiconductor detectors including silicon carbide diodes; as well as novel approaches such as ionoacoustic range sensing for proton beams. For each modality and detector type, we emphasize clinical relevance, measurement accuracy, spatial resolution, radiation durability, and suitability for high dose-per-pulse environments (e.g., FLASH radiotherapy). Current challenges, such as detector response in regions of steep dose gradient, saturation or recombination at ultra-high dose rates, and energy-dependent sensitivity in mixed radiation fields, are analyzed in detail. We also highlight the limitations of each technique and discuss ongoing improvements and prospects for clinical implementation. In summary, no single detector technology fully satisfies all requirements for fast, high-accuracy, high-resolution, radiation-hard PDD measurement, but the integration of emerging sensor innovations into clinical dosimetry promises to enhance the precision and efficiency of radiotherapy quality assurance. Full article

A four-quadrant low-coherence envelope detection method was proposed for measuring the surface spacing of optical components, eliminating the requirement for precise control of the delay line scanning step to generate a π/2 phase shift. The method employs an orthogonal polarization Mach–Zehnder (MZ) fiber interferometer, illuminated by a broadband superluminescent diode (SLD), and a four-quadrant polarization-resolved detector to simultaneously acquire spatially phase-shifted interference signals carrying surface spacing information. The interference envelope is directly demodulated to extract surface spacing, thereby decoupling measurement accuracy from mechanical stepping constraints. To enable real-time, high-precision calibration of the delay line, two complementary schemes were implemented: wavelength division multiplexing (WDM)-based calibration and dual optical path calibration. Experimental results confirm that the dual-path scheme exhibits weak dependence on scanning velocity and remains stable across a wide speed range. Repeat measurements of the surface spacing of a 1 mm thick sapphire plate yielded a standard deviation (STD) of 1.3 μm. By relaxing the strict π/2 phase shift condition traditionally imposed on scanning step size, this method improves operational efficiency while maintaining measurement reliability—providing a robust and broadly applicable solution for metrology, including lens surface spacing and transparent plate thickness characterization. Full article

Ensuring the structural integrity of high-energy piping systems is a critical requirement for the safe operation of nuclear power plants. This paper presents the design, implementation, and three-year operational validation of a three-dimensional displacement monitoring system installed on the steam generator blowdown pipeline of the Krško Nuclear Power Plant. The system was developed to verify that the plant’s operating procedures will not induce excessive dynamic displacements during operation. The measurement system configuration utilizes three non-collinear inductive displacement transducers from Hottinger Baldwin Messtechnik (HBM WA/500 mm-L), mounted via miniature universal joints to a reference plate and to a defined observation point on the pipeline. This arrangement enables the real-time monitoring of X, Y, and Z displacements within a spherical measurement volume of approximately 0.5 m. Data are continuously acquired via an HBM QuantumX MX840B amplifier and processed using CATMAN Easy-AP software through a fiber-optic communication link between the containment and control areas. The system has operated continuously for more than three years under elevated temperature and radiation conditions, confirming its reliability and robustness. The correlation of the measured displacements with process parameters such as the flow rate, pressure, and temperature provides valuable insight into transient events and contributes to predictive maintenance strategies. The presented methodology demonstrates a practical and radiation-tolerant approach for the continuous structural monitoring of nuclear plant piping systems. Full article

Understanding the fluid dynamics of fluidized beds loaded with biomass pellets is of significant value for the design of wood waste gasifiers. In the present study, cylindrical wood pellets are loaded into a lab-scale cold gasifier unit at 2.5 vol% and 7.5 vol% concentrations and studied at superficial air velocities of 0.25, 0.282, and 0.344 m/s (corresponding to 80, 90, and 110 SCFM). Measurements of bubbles, sand particles, and biomass pellets are taken at a 45 cm height from the distributor plate, and at 9, 12, 15, 18, and 21 cm radial positions from the column wall by employing the CREC-GS-Optiprobes, a valuable integrated fiber optic-laser tool system. A new data processing methodology is established using laser signals that are reflected from the outer surface of aluminum-foil-wrapped cylindrical wood pellets. In addition, a new algorithm is implemented to distinguish pellet-reflected signals from those of bubbles and emulsion-phase particles. On this basis, for the first time, a Phenomenological Probabilistic Predictive Model (PPPM), is considered to predict Bubble Axial Chords (BACs) and Bubble Rise Velocities (BRVs), in a sand fluidized bed loaded with biomass pellets. This is accomplished within a set band of values accounting for three standard deviations from their means or including 85.9% of the bubbles measured. Thus, it is demonstrated that the PPPM is adequate to establish the constrained random motion of bubbles in sand fluidized beds, under the influence of uniformly distributed biomass pellets. It is anticipated that the findings of the present study will be of significant value for the design of sand biomass gasifiers of different scales. Full article

A reflective all-fiber optical current transformer based on a spatial non-reciprocal phase modulation technique is investigated by theoretical analysis and experimental measurement. The modulation unit, composed of a phase delay wave plate (LiNbO₃) and two Faraday rotators, achieves flexible frequency adjustment by converting modulation from the time domain to the spatial domain. Therefore, the avoidance of the impact caused by delay coils is achieved in principle. The absence of intrinsic frequency limitations eliminates the demand for precise timing control in demodulation, thereby simplifying the demodulation circuit and reducing the cost and size of the transformer. In previous studies, redundancies were identified in the optical path coupling devices. The half-wave voltage of the modulator is excessively high, and its size is considerable due to constraints inherent in the manufacturing process. The measurement range is within 1800 A. The scheme simplifies some optical path components. By optimizing the phase delay wave plate, the half-wave voltage of the modulator is significantly reduced by a factor of 150. Experimental results demonstrate that the current transformer exhibits excellent detection consistency within the rated current range of 30–3600 A (1–120%), the response time is within 3 ms, and the measurement error and peak error reach 0.052% and 0.127%. This configuration provides a novel option for the design and practical application of all-fiber optical current transformers. Full article

Reliable in situ quantification of interlayer mechanics in CRTS-II ballastless track slabs remains limited by the poor instrumentability of the CA mortar layer. This study implements a quasi-distributed fiber-optic sensing scheme by encapsulating FBGs in PVC conduits and embedding them within the CA mortar to track strain evolution under vertical loading. Four 1:3 scaled slabs were tested using stepwise load control (200 kN per step) to failure, and fiber measurements were cross-validated against conventional strain gauges on the reinforcement. The two systems showed consistent load–strain trends, while the fiber approach exhibited near-zero baseline offset and higher temporal resolution, enabling detection of small-amplitude strain changes that the gauges missed. The CA mortar displayed a clear tension-to-compression transition with increasing load; with two vertical rebars the ultimate load of the mortar layer reached 1400 kN, representing a 75% improvement over the rebar-free configuration and delaying compressive crushing through enhanced interlayer cooperation. Increasing the rebar diameter further restrained deformation and elevated the load level at which the transition occurred. The results demonstrate a practical interlayer monitoring route for CA mortar and quantify the strengthening role of vertical rebars, offering actionable guidance for design optimization and long-term condition assessment of CRTS-II slab tracks. Full article

The novel fibrous composites of Al₆₁Cu₂₇Fe₁₂ alloy with a single-crystalline matrix and quasi-crystal phase fraction obtained in situ by directional solidification by the Bridgman method were studied to characterize the voids and their role in composites cracking. The voids were analyzed using light-optical and scanning electron microscopy to study their nature before and after uniaxial tensile tests. Tension tests were performed on plate-like samples up to rupture. The tensile fracture surfaces were also observed and analyzed. The single-crystallinity and crystalographic parameters of composites were studied using the X-ray Laue diffraction method. It was stated that such new type of composite is characterized by a relatively high void content with a ratio of approximately 2.6%. The composite’s cracking is initiated at voids and progress through the voids and stair steps in the matrix and the reinforcing fibers. Full article

The wide-spread application of carbon fiber-reinforced polymer (CFRP) composites in industrial fields has led to high demand for developing a rapid detection method for assessing the structural performance of CFRP composites in operation based on optical fiber sensing technology. Therefore, the effectiveness and reliability of evaluating the fatigue resistance of CFRP plates based on fiber Bragg grating (FBG) monitoring information were explored. The strain response of CFRP plates at key positions under constant amplitude fatigue load was monitored by bare FBGs in series and packaged quasi-distributed FBGs in series. The structural performance and fatigue resistance characteristics of CFRP plates were evaluated by statistical analysis and fatigue life prediction theory. The validity and accuracy of the test and analysis results were demonstrated by finite element modeling analysis. Compared with the traditional methods that evaluate the structural fatigue performance based on mass destructive experiments, this method significantly improves the detection efficiency and realizes the non-destructive and rapid online evaluation of structural service performance. Research shows that the designed FBG sensors can effectively monitor the strain response of CFRP plate under fatigue load, and the correlated fatigue algorithm can provide feasible and reliable technical approaches for online detection and evaluation on the structural performance of CFRP components. Full article

The paper studies the distribution of relative displacement of a composite plate with integrated fiber Bragg gratings. The analysis of the methods for manufacturing composite plates with embedded optical fibers containing FBG sensors, as well as the spectral characteristics of the gratings under various bending conditions, are performed. The effect of sensor arrangement on the accuracy of determining stresses and relative elongations of the material is experimentally studied. The features of spectral shifts that occur under non-uniform stresses are revealed, which can reduce the accuracy of measurements when using interrogators. The patterns of change in the central wavelength of Bragg gratings depending on the type and magnitude of plate bending are established. The research results confirm that the use of a network of embedded FBG sensors allows one to accurately determine the areas of maximum deformations, as well as the nature and magnitude of bending of composite structures. The data obtained can be used to develop more accurate systems for monitoring the stress–strain state of composite materials. Full article

The purpose of this study was to evaluate the bactericidal effect of 270 nm UV-C light-emitting diode (LED) light delivered through a newly designed prototype device with thin optical fiber against Enterococcus faecalis (E. faecalis). The prototype device, developed to integrate UV-C light into a thin optic fiber (diameter 124 µm) connected to a UV-C LED (Luminous Device; Sunnyvale, CA, USA) via a specialized double-lens system that focuses divergent light to achieve a 65 mm working distance and a numerical aperture of 0.22. E. faecalis, was cultured at 37 °C under aerobic conditions for 24 h. The UV-C LED optical fiber was positioned 10 mm above the bacterial culture prepared in the wells of a 96-well plate. The E. faecalis cells were exposed to UV-C irradiation for 0, 10, 30, 60, 90, 120 and 180 s. Following irradiation, the OD600 values were measured after incubation at 37 °C for an additional 24 h. The data were statistically analyzed using one-way ANOVA, followed by Tukey’s honestly significant difference (HSD) test at a significance level of 0.05. UV irradiation at 270 nm significantly reduced E. faecalis growth in a time-dependent manner (p < 0.05). No significant changes were observed at 0 and 10 s, while peak reductions occurred at 120 and 180 s, with effects beginning at 30 s and increasing over time. The 270 nm UV-C wavelength was highly effective in bactericidal action against E. faecalis. The custom-designed UV-C delivery system effectively integrated the light source into a thin optical fiber, allowing for efficient UV-C light transmission and demonstrating its potential for application in narrow spaces such as root canals. Full article

A bistable effect on a laminate structure with a piezoelectric patch was tested to harvest kinetic energy. The composite bistable plate was prepared in the autoclave with two different orientations of the glass fibers. The dynamic tests were performed on the universal testing machine using cyclic vertical compression excitation. During the tests, the bottom edge of the plate was clamped firmly while its upper edge was attached with some clearance to enable sliding. In such a configuration, the friction force between the plate and upper clamp element is responsible for the plate excitation. Simultaneously, the plate has enough space to change the shape between the two equilibria. During the harmonic excitation of the testing machine operating mode, a piezoelectric element was placed on the bistable plate and its voltage and normalized power outputs were evaluated. The experiments were repeated with additional mass distribution, which influenced the natural frequency of the plate. Full article

Compressive testing of specimens taken from relatively thin composite plates is difficult, especially due to the occurrence of buckling. To prevent buckling, the central portion of the specimens used for the compression test has smaller dimensions, and the specimens can be guided along their entire length. For these reasons, optical methods, such as digital image correlation (DIC), cannot be used for the compression test and strain rosettes cannot be glued onto the samples to determine Poisson’s ratio. In this study, compression tests of a glass fiber-reinforced polymer (GFRP) were conducted using both the ASTM D695 (Boeing version) and a newly proposed method. The new method involves using special specimens that allow T-type rosettes to be bonded to determine Poisson’s ratio, whose value of 0.14 was thus determined. SEM images of the failure surfaces were presented and interpreted. A finite element analysis (FEA) of the specimens tested in compression is also presented. The first analyzed case considers the homogeneous and orthotropic composite, loaded with a uniformly distributed force. The normal stress in the central section of the specimen, determined with FEA, has an error of 6.52% compared to that determined experimentally. Additionally, the strain in the center of the strain gauge, determined with FEA, has an error of 4.76% compared to the measured one. In the second case studied with FEA, the sample is loaded with a quasi-concentrated force, which can move in the direction of the symmetry axes of the cross-section, to study the effect of the eccentricity of the compression force on the state of stress. It was shown that the eccentricity of the force has a great influence: the stress distribution in the section of the specimen becomes strongly non-uniform. For a force eccentricity of 0.4 mm in the direction of the OX axis, the minimum stress decreases by 53.7%, and the maximum stress increases by 55.4%. In order to analyze the influence of some manufacturing defects, two other cases were analyzed by FEA, in which it was assumed that the thicknesses of the outer resin layers were modified, making them asymmetrical. For this final FEA, the specimen was considered to be composed of laminates. These results demonstrate the special attention that must be paid to the centric application of force in compression testing. Full article

A reinforced earth wall is a structure in which reinforcement materials are placed in an embankment to build a vertical or nearly vertical wall surface. Such walls have been widely used in roads and in developed land since around 1960. Reinforcement materials have a set service life of 100 years and fall into two types: steel and geosynthetics. To ensure long-term durability, steel reinforcement materials are plated, while geosynthetics are designed with a limit strength designed to resist fracture for 100 years under the conditions of a given load placed on the reinforcement materials. However, owing to the difficulty of assessing the condition of reinforcement materials in soil, this paper proposes solutions based on non-destructive methods. Specifically, it proposes a method of assessing the amount of strain through an embedded optical fiber in the case of geosynthetic reinforcement materials, or magnetic surveying to investigate the degree of corrosion in the case of steel reinforcement materials. This paper demonstrates that it is possible to non-destructively assess the state of either type of reinforcement material. Full article