Search Results (45)

Cyclic voltammetry (CV) is an accessible, readily available, non-expensive technique that can be used to search for the interaction of compounds with DNA and detect the strongest DNA-binding from a set of compounds, therefore allowing for the optimization of the number of cytotoxicity assays. Focusing on this electrochemical approach, the study of twenty-seven camphorimine silver complexes of six different families was performed aiming at detecting interactions with calf thymus DNA (CT-DNA). All of the complexes display at least two cathodic waves attributed respectively to the Ag(I)→Ag(0) (higher potential) and ligand based (lower potential) reductions. In the presence of CT-DNA, a negative shift in the potential of the Ag(I)→Ag(0) reduction was observed in all cases. Additional changes in the potential of the waves, attributed to the ligand-based reduction, were also observed. The formation of a light grey product adherent to the Pt electrode in the case of {Ag(OH)} and {Ag₂(µ-O)} complexes further corroborates the interaction of the complexes with CT-DNA detected by CV. The morphologic analysis of the light grey material was made by scanning electronic microscopy (SEM). The magnitude of the shift in the potential of the Ag(I)→Ag(0) reduction in the presence of CT-DNA differs among the families of the complexes. The complexes based on {Ag(NO₃)} exhibit higher potential shifts than those based on {Ag(OH)}, while the characteristics of the ligand (^AL-Y, ^BL-Y, ^CL-Z) and the imine substituents (Y,Z) fine-tune the potential shifts. The energy values calculated by docking corroborate the tendency in the magnitude of the interaction between the complexes and CT-DNA established by the reaction coefficient ratios (Q_[Ag-DNA]/Q_[Ag]). The molecular docking study extended the information regarding the type of interaction beyond the usual intercalation, groove binding, or electrostatic modes that are typically reported, allowing a finer understanding of the non-covalent interactions involved. The rationalization of the CV and cytotoxicity data for the Ag(I) camphorimine complexes support a direct relationship between the shifts in the potential and the cytotoxic activities of the complexes, aiding the decision on whether the cytotoxicity of a complex from a family is worthy of evaluation. Full article

Difficult-to-cut titanium matrix composites (TiB+TiC)/Ti6Al4V have extensive application prospects in the fields of biomedical and aerospace metal microcomponents due to their excellent mechanical properties. Jet electrochemical micromilling (JEMM) technology is an ideal method for machining microstructures that leverages the principle of electrochemical anodic dissolution. However, the matrix Ti6Al4V is susceptible to passivation during electrochemical milling, and the inclusion of high-strength TiB whiskers and TiC particles as reinforcing phases further increases the machining difficulty of (TiB+TiC)/Ti6Al4V. In this study, a novel approach using NaCl+NaNO₃ mixed electrolyte for the JEMM of (TiB+TiC)/Ti6Al4V was adopted. Electrochemical behaviors were measured in NaCl and NaCl+NaNO₃ electrolytes. In the mixed electrolyte, a higher transpassive potential was required to break down the passive film, which led to better corrosion resistance of (TiB+TiC)/Ti6Al4V, and the exposed reinforcing phases on the dissolved surface were significantly reduced. The results of the JEMM machining indicate that, compared to NaCl electrolyte, using mixed electrolyte effectively mitigates stray corrosion at the edges of micro-grooves and markedly improves the uniformity of both groove depth and width dimensions. Additionally, the surface quality was noticeably improved, with a reduction in Ra from 2.84 μm to 1.03 μm and in Rq from 3.41 μm to 1.40 μm. Full article

Molybdenum is an important material in modern industry, widely used in extreme environments such as rocket engine nozzles and microelectrodes due to its high melting point, excellent mechanical properties, and thermal conductivity. However, as a difficult-to-machine metal, traditional machining methods struggle to achieve the desired microstructures in molybdenum. Electrochemical machining (ECM) offers unique advantages in manufacturing fine structures from hard-to-machine metals. Studies have shown that molybdenum exhibits a fast corrosion rate in alkaline or acidic solutions, posing significant environmental pressure. Therefore, this study investigates the electrochemical machining of molybdenum in neutral salt solutions to achieve high-precision microstructure fabrication. First, the polarization curves and electrochemical impedance spectroscopy (EIS) of molybdenum in NaNO3 solutions of varying concentrations were measured to determine its electrochemical reaction characteristics. The results demonstrate that molybdenum exhibits good electrochemical reactivity in NaNO3 solutions, leading to favorable surface erosion morphology. Subsequently, a mask electrochemical machining technique was employed to fabricate arrayed microstructures on the molybdenum surface. To minimize interference between factors, an orthogonal experiment was used to optimize the parameter combination, determining the optimal machining process parameters. Under these optimal conditions, an array of micro-groove structures was successfully fabricated with an average groove width of 110 μm, a depth-to-width ratio of 0.21, an aspect ratio of 9000, and a groove width error of less than 5 μm. Full article

Bearing steel (GCr15) is widely used in key parts of mechanical transmission for its excellent mechanical properties. Electrochemical machining (ECM) is a potential method for machining GCr15, as the machining process is the electrochemical dissolution of GCr15 regardless of its high hardness (>50 HRC). In ECM, NaNO₃ solution is a popular electrolyte, as it has the ability to help in the nonlinear dissolution of many metallic alloy materials, making it useful for precision machining. However, due to high carbon content of GCr15, the electrochemical dissolution of GCr15 is unique, and there is always a black layer with high roughness on the machined surface, reducing the surface quality. In order to improve the electrochemical machining of GCr15 with a high surface quality, the surface characteristics of GCr15 in ECM were investigated. The anodic polarisation curve in the NaNO₃ electrolyte was measured and electrochemical dissolution experiments were conducted with different current densities. SEM, XRD, and XPS were employed to analyse the surface morphology and composition formed on the machined surface at different current densities. The initial results showed that there were two parts (black part and bright part) formed on the machined surface when a short circuit occurred, and the test results suggested that the black part contained a mass of Fe₃O₄ while the bright part was composed of mainly Fe and Fe₃C. Further investigation uncovered that a black flocculent layer (Fe₃O₄) always formed in a low current density (32 A/cm²) with high roughness. With the current density increased, the amount of black flocculent layer was reduced, and Fe₃C particles appeared on the machined surface. When the current density reached 81 A/cm², the entire flocculent oxide layer was removed, only some spherical Fe₃C particles were inserted on the machined surface, and the roughness was reduced from Ra7.743 μm to Ra1.783 μm. In addition, due to exposed Fe₃C particles on the machined surface, the corrosion resistance of the machined surface was significantly improved. Finally, circular arc grooves of high quality were well manufactured with current density of 81 A/cm² in NaNO₃ electrolyte. Full article

Ultra-thin 304 stainless steel can be used to flexibly display substrates after they have been subjected to chemical mechanical polishing (CMP). The thickness of the chemical oxide layer directly affects the polishing efficiency and surface quality of 304 stainless steel. In the study presented in the following paper, the thickness variation of the chemical oxide layer of 304 stainless steel was analyzed following electrochemical corrosion under different oxidant concentration conditions. Furthermore, the impact of the oxidant concentration on the grooves, chips, and scratch depth–displacement–load curves was investigated during a nano-scratching experiment. Through this process, we were able to reveal the chemical reaction mechanism between 304 stainless steel materials and oxidizers. The corrosion rate was found to be faster at 8% oxidant content. The maximum values of the scratch depth and elastic–plastic critical load were determined to be 2153 nm and 58.47 mN, respectively. Full article

Surgical ASTM F139 stainless steel is used for temporary fixtures in the biomedical field. Tribocorrosion is a major concern in this application. The aim of the present work was to study the interplay between tribocorrosion behavior and the surface chemistry of the ASTM F139 stainless steel in phosphate-buffered saline solution (PBS). Sliding wear tests were conducted against alumina balls at different electrochemical potentials: open circuit potential (OCP), cathodic potential (−100 mV versus the OCP), and anodic potentials (+200 mV_Ag/AgCl and +700 mV_Ag/AgCl). The normal load was 20 N. The wear volume was estimated based on micrographs obtained from the wear tracks using confocal laser scanning microscopy. Moreover, the wear tracks were also examined by scanning electron microscopy (SEM). The surface chemistry of the ASTM F139 specimens was analyzed by X-ray photoelectron spectroscopy (XPS). The wear volume was dependent on the electrochemical potential, being maximized at +700 mVAg/AgCl. Delamination areas and grooves were observed in the wear tracks. Detailed assessment of the surface chemistry inside the wear tracks allowed identification of the main chemical species and their relative quantities, thus enabling correlation of the passive film composition with the observed tribocorrosion behavior. Full article

Wire beam electrode techniques and classical electrochemical techniques were used to investigate the effect of the area ratio of each part of the welded joint on the galvanic corrosion behavior. The results showed that the order of the corrosion current density of the different regions in the simulated X80 steel welded joint was as follows: coarse-grained heat-affected zone > fine-grained heat-affected zone > intercritical heat-affected zone > base metal > weld metal. As the area ratio of weld metal increased, the galvanic potential shifted positively, the maximum anode galvanic current density increased and the main anode galvanic effect increased. On the other hand, as the area ratio of the base metal and the heat-affected zone decreased, the coupled potential shifted negatively and the maximum anode galvanic current density decreased. The galvanic corrosion intensity of the simulated X80 steel welded joint increased as the area ratio of the weld metal decreased and increased as the area ratio of the heat-affected zone and base metal increased. To enhance corrosion resistance, it is advisable to choose a shape with a larger groove to increase the WM area in the welded joint. Additionally, selecting a welding method with lower heat input and a higher energy density can help reduce the HAZ area in the welded joint. Full article

This study created ceramic preforms with a 3D network structure (TAD_3D) by using treated aluminum dross (TAD) and kaolin slurry, with 30 ppi polyurethane foam as a template via the sacrificial template method. TAD_3D/5A05Al composites were then produced via pressureless infiltration of 5A05Al aluminum alloy into TAD_3D. The corrosion behavior and resistance of TAD_3D/5A05Al in salt spray were assessed via neutral salt spray corrosion (NSS), scanning electron microscopy (SEM), potentiodynamic polarization (PDP), and electrochemical impedance spectroscopy (EIS) tests. The results showed that after 24 to 360 h of NSS corrosion, the corrosion of the 5A05 matrix was primarily pitting, with pits expanding and deepening over time, and showing a tendency to interconnect. The main corrosion products were MgAl₂O₄, Al(OH)₃, and Al₂O₃. As corrosion progressed, these products increased and filled cracks, pits, and grooves at the composite interface on the material’s surface. Corrosion products transferred to the grooves at the composite interface and grew on the ceramic surface. Corrosion products on the ceramic framework and the Al matrix can form a continuous passivation film covering the composite surface. PDP and EIS results indicated that the composite’s corrosion resistance decreased by 240 h but increased after that time. After 240 h, the surface passivation film can weaken corrosion effects and enhance the composite’s resistance, although it remained weaker than that of the uncorroded samples. Additionally, grooves at the composite interface deepened over time, with loosely structured corrosion products inside, potentially leading to severe localized corrosion. Full article

In Li-ion batteries, ion diffusion kinetics represent a limitation to combine high capacity and a fast charging rate. To bypass this, textured electrodes have been demonstrated to increase the active surface, decrease the material tortuosity and accelerate the electrolyte wetting. Amongst the structuring technologies, ultrashort pulse laser processing may represent the key option enabling, at the same time, high precision, negligible material deterioration and high throughput. Here, we report a study on the structuring of electrodes with both holes and grooves reaching the metallic collector. Electrochemical models emphasize the importance of hole and line dimensions for the performances of the cell. We demonstrate that we can control the hole and line width by adjusting the applied fluence and the repetition rate. In addition, results show that it is possible to drill 65 µm-deep and ~15 µm-wide holes in nearly 100 µs resulting in up to 10,000 holes/s. To further reduce the takt time, bursts of 40 MHz pulses were also investigated. We show that bursts can reduce the takt time by a factor that increases with the average power and the burst length. Moreover, at comparable fluence, we show that bursts can shorten the process more than theoretically expected. Full article

Titanium alloys are widely used in aerospace and biomedicine because of their excellent mechanical characteristics, but these properties also make such alloys difficult to cut. Jet electrochemical micromilling (JEMM) is based on the principle of electrochemical anodic dissolution; it has some inherent advantages for the machining of titanium alloy microstructures. However, titanium oxidizes readily, forming an oxide film that impedes a uniform dissolution during electrochemical machining. Therefore, a high voltage and an aqueous NaCl electrolyte are usually used to break the oxide film, which can lead to severe stray corrosion. To overcome this problem, the present study investigated the JEMM of Ti-6Al-4V using a NaCl–ethylene glycol (NaCl-EG) electrolyte. Electrochemical testing showed that Ti-6Al-4V exhibits a better corrosion resistance in the NaCl-EG electrolyte compared to the aqueous NaCl electrolyte, thereby reducing stray corrosion. The localization and surface quality of the grooves were enhanced significantly when using JEMM with a NaCl-EG electrolyte. A multiple-pass strategy was adopted during JEMM to improve the aspect ratio, and the effects of the feed depth and number of passes on the multiple-pass machining performance were investigated. Ultimately, a square annular microstructure with a high geometric dimensional consistency and a smooth surface was obtained via JEMM with multiple passes using the optimal parameters. Full article

Polymer–metal hybrid structures combine the merits of polymer and metal materials, making them widely applicable in fields such as aerospace and automotive industries. However, the main challenge lies in achieving efficient and strong connections between the metal and polymer components. This paper uses the jet electrochemical machining (Jet-ECM) method to customize the surface morphologies on 6061 aluminum alloy (AA6061) sheets. The connection between AA6061 and carbon fiber-reinforced PA66 (CF/PA66) is then achieved through hot pressure welding (HPW). The effects of aluminum alloy surface morphology, welding force, and welding time on the mechanical properties and microstructure of the joint are investigated. The optimal process parameters are determined by the design of the experiment. The results show that the aluminum alloy surface morphology has the greatest impact on the mechanical property of the welded joint. The optimal process parameters are surface morphology with wider, shallower, and sparsely distributed grooves on the aluminum alloy surface, the welding force is 720 N, the welding time is 12 s, the welding temperature is 360 °C, the cooling time is 16 s, and the optimal peak load of the joint is 6690 N. Under the optimal parameters, the fracture morphology in the AA6061 side is almost entirely covered with CF/PA66. The joint experiences cohesive failure in most areas and fiber-matrix debonding in a small area. Full article

In this study, the effects of three distinct surface treatment techniques on 316L stainless steel were investigated: low-temperature immersion corrosion, shot peening followed by immersion corrosion, and electrochemical corrosion. These techniques were selected with a focus on their potential implications for biomedical implant applications, as research gaps persist in understanding the influence of these treatments. A comprehensive examination of surface alterations was conducted using scanning electron microscopy, Raman spectroscopy, and α-step thin-film thickness profiling. Furthermore, human MG-63 osteoblastic cell line adhesion was evaluated using Liu’s stain and metallographic optical microscopy. Notable differences in cell-adhesion behavior based on the chosen surface treatment methods were observed. Specifically, weak cell adhesion was observed after low-temperature immersion and shot peening followed by immersion corrosion. In contrast, electrochemical corrosion, especially when conducted with a high current density and low corrosive-solution concentration, resulted in a uniformly corroded surface, which, in turn, promoted dense cell adhesion. Porous oxide layers were generated using all three techniques, but the efficacy of shot peening (applied at 1 kg/cm² for 20 s) and electrochemical corrosion (using 0.5 M HCl) as promising processes were highlighted by our experimental results. Uniformly dense corrosion pits were produced through electrochemical corrosion, while semicircular grooves with small corrosion pits were the result of shot peening, both of which were found to be favorable for cell adhesion. The superior cell adhesion observed with electrochemical corrosion further emphasizes its suitability for biomedical applications. Full article

Thermoforming (TF) is a process used for fabricating products by applying heat and vacuum pressure to a plastic film or plate. Typically, TF molds require post-processing, resulting in additional costs and time consumption. Furthermore, continuous application of lubricant is necessary to prevent corrosion and facilitate mold release. Electrochemical polishing (ECP) is a technique used to achieve a polished surface on metal through an electrochemical reaction. In this research, a novel approach is proposed as a solution to the need for lubricants and manual post-processing in mold preparation, utilizing pulse electrochemical polishing (PECP). A comparative analysis is conducted on the reproducibility of products and the forces required for mold release among molds prepared using PECP, lubricated molds, and unpolished molds. To assess product reproducibility, the radii of curvature of all mold steps and grooves are determined and compared. Furthermore, peeling tests are conducted to estimate the forces required for mold release. Product surface evaluation is performed using atomic force microscopy, while lateral force microscopy is employed to measure the reductions in surface frictional force achieved by PECP. Full article

Machining hard-to-cut materials, such as cobalt (Co)-based superalloys, is a common problem in manufacturing industries. Background: wire electrical discharge machining (W-EDM) is one of the widely used cutting processes that causes layer (white layer—WL and heat-affected zone—HAZ) formation, and microcracks on the material’s surface. Purpose: this study investigates the effects of WL and HAZ on the electrochemical grooving (EC grooving) performance of Co-based superalloys. Two different surface types (W-EDMed and VFed) were used in the experiments. Result: the experiments showed that material removal rate (MRR) values increased up to 212.49% and 122.23% for vibratory finished (VFed) and wire-electrical-discharge-machined (W-EDMed) surfaces, respectively. Conclusion: This result indicates the presence of HAZ and WL that prevent current transition between two electrodes. However, increased voltage causes an increase in surface roughness, with increment rates at 71.13% and 36.08% for VFed and W-EDMed surfaces, respectively. Moreover, for the VFed surfaces, the groove lost its flatness at the bottom after an approximately 100 µm depth due to the different electrochemical machineabilities of HAZ and real surface texture. This result can be attributed to the different microstructures (HAZ and surface texture) showing different electrochemical dissolution rates. Therefore, high-depth distance HAZ and WL must be removed from the workpiece. Full article

To solve the problem of the nonuniform distribution of temperature and electrolytic products in the electrolyte flow field during through-mask electrochemical micromachining, the use of a rotating cathode with surface structures is proposed. The rotation of the cathode increases the efficiency of heat and mass transfer by the electrolyte flow. Simulations are performed to analyze the influence of the type of surface structure, the number of surface structures, and the rotational speed of the cathode on the electrolyte flow field. The results show that the use of a rotating cathode with surface structures significantly improves the mass transfer efficiency of the electrolyte flow field in comparison with a conventional cathode structure, and, in particular, a grooved rotating cathode can increase the outlet flow velocity by about 23%. An experimental demonstration of micropit array processing shows that the use of a grooved rotating cathode increases the mass transfer efficiency by 34% and the processing efficiency by nearly 40% compared with a smooth-surfaced rotating cathode. The grooved rotating cathode also gives the highest machining accuracy. Using this cathode, a uniform micropit array with an average micropit diameter of 201.83 μm, a diameter standard deviation of 3.49 μm, and a depth standard deviation of 0.87 μm is processed. Full article