Search Results (1,250)

This study investigates the hot deformation behaviour and microstructural evolution of two AISI 430 ferritic stainless steel variants: 0A (basic) and 1C (modified). These variants primarily differ in chemical composition, with 0A containing higher austenite-stabilizing elements (C, N) compared to 1C, which features lower interstitial content and slightly higher Si and Cr. This research aimed to optimize hot rolling conditions for enhanced forming properties. Uniaxial hot compression tests were conducted using a Gleeble thermo-mechanical system between 850 and 990 ${}^{\circ }$C at a strain rate of 3.3 s${}^{-1}$, simulating industrial finishing mill conditions. Analysis of flow curves, coupled with detailed microstructural characterization using electron backscatter diffraction, revealed distinct dynamic restoration mechanisms influencing each material’s response. Thermodynamic simulations confirmed significant austenite formation in both materials within the tested temperature range, notably affecting their deformation behaviour despite their initial ferritic state. Material 0A consistently exhibited a strong tendency towards dynamic recrystallization (DRX) across a wider temperature range, particularly at 850 ${}^{\circ }$C. DRX led to a microstructure with a high concentration of low-angle grain boundaries and sharp deformation textures, actively reorienting grains towards energetically favourable configurations. However, under this condition, DRX did not fully complete the recrystallization process. In contrast, material 1C showed greater activity of both dynamic recovery and DRX, leading to a much more advanced state of grain refinement and recrystallization compared to 0A. This indicates that the composition of 1C helps mitigate the strong influence of the deformation temperature on the crystallographic texture, leading to a weaker texture overall than 0A. Full article

Colloidal silica acts as a multifunctional reagent in the froth flotation process of semi-soluble salt-type minerals, enabling the selective depression of calcite. This study investigates its effect on four key minerals—calcite, scheelite, apatite, and fluorite—using a comprehensive suite of techniques to identify the flotation subprocesses modulated by colloidal silica. This work also aims to determine the specific flotation zones affected by colloidal silica, assessing the influence of its dosage, surface modification, and specific surface area on metallurgical outcomes. Atomic force microscopy revealed mineral-specific surface responses to colloidal silica conditioning: calcite exhibited localized nanoparticle adsorption, whereas apatite underwent a dissolution–reprecipitation mechanism. Scheelite and fluorite, in contrast, showed minimal surface modifications. These differences are attributed to variations in surface reactivity, hydration behavior, and crystallographic structure, with calcite offering a uniquely favorable environment for colloidal silica attachment. Mechanistic insights show that colloidal silica—especially the aluminate-modified type with high specific surface area—influences both the pulp and froth zones by producing small, stable bubbles, enhancing fine scheelite recovery, stabilizing froth, and effectively depressing calcite. In contrast, non-functionalized colloidal silica resulted in poor bubble control and unstable froth. These findings elucidate the subprocess-specific mechanisms by which colloidal silica operates and highlight its potential as a tunable, multifunctional reagent for improving selectivity in the flotation of semi-soluble salt-type minerals. Full article

Fumonisins, primarily produced by Fusarium spp. and Aspergillus section nigri, are common contaminants in maize, cereal grains, and other processed and derived products, representing a significant risk to food safety and public health. This study presents the development and optimisation of a high-performance liquid chromatography method with fluorescence detection (HPLC-FLD) for the quantification of fumonisin B1 (FB1) and B2 (FB2) in various food matrices. In contrast with conventional protocols employing potassium phosphate buffers as the mobile phase, the proposed method utilises formic acid, offering enhanced compatibility with liquid chromatography systems. An automated online precolumn derivatisation with o-phthaldialdehyde (OPA) was optimised through experimental design and response surface methodology, enabling baseline separation of FB1 and FB2 derivatives in less than 20 min. The method demonstrated high sensitivity, with limits of detection of 0.006 µg mL⁻¹ for FB1 and 0.012 µg mL⁻¹ for FB2, and excellent repeatability (intraday RSD values of 0.85% and 0.83%, respectively). Several solid-phase extraction (SPE) strategies were evaluated to enhance sample clean-up using a variety of food samples, including dried figs, raisins, dates, corn, cornmeal, wheat flour, and rice. FumoniStar Inmunoaffinity columns were the only clean-up method that provided optimal recoveries (70–120%) across all tested food matrices. However, the MultiSep™ 211 column yielded good recoveries for both fumonisins in dried figs and raisins. Additionally, the C18 cartridge achieved acceptable recoveries for both fumonisins in dried figs and wheat flour. Full article

Background/Objectives: Direct oral anticoagulants (DOACs) are now the guideline-recommended alternative to vitamin K antagonists (VKAs) for long-term anticoagulation in patients with non-valvular atrial fibrillation. However, accurately assessing their impact on ischemic stroke outcomes remains challenging, primarily due to uncertainty regarding anticoagulation status at the time of hospital admission. This preliminary study addresses this gap by using point-of-care testing (POCT) to confirm DOAC activity at bedside, allowing for a more accurate comparison of 90-day functional outcomes between anticoagulated and non-anticoagulated stroke patients. Methods: We conducted a retrospective cohort study of 786 ischemic stroke patients admitted to the University of Pécs between February 2023 and February 2025. Active DOAC therapy was confirmed using the ClotPro^® viscoelastic testing platform, with ecarin Clotting Time (ECT) employed for thrombin inhibitors and Russell’s Viper Venom (RVV) assays for factor Xa inhibitors. Patients were categorized as non-anticoagulated (n = 767) or DOAC-treated with confirmed activity (n = 19). Mahalanobis distance-based matching was applied to account for confounding variables including age, sex, pre-stroke modified Rankin Scale (mRS), and National Institutes of Health Stroke Scale (NIHSS) scores at admission and 72 h post-stroke. The primary outcome was the change in mRS from baseline to 90 days. Statistical analysis included ordinary least squares (OLS) regression and principal component analysis (PCA). Results: After matching, 90-day functional outcomes were comparable between groups (mean mRS-shift: 2.00 in DOAC-treated vs. 1.78 in non-anticoagulated; p = 0.745). OLS regression showed no significant association between DOAC status and recovery (p = 0.599). In contrast, NIHSS score at 72 h (p = 0.004) and age (p = 0.015) were significant predictors of outcome. PCA supported these findings, identifying stroke severity as the primary driver of outcome. Conclusions: This preliminary analysis suggests that ischemic stroke patients with confirmed active DOAC therapy at admission may achieve 90-day functional outcomes comparable to those of non-anticoagulated patients. The integration of bedside POCT enhances the reliability of anticoagulation assessment and underscores its clinical value for real-time management in acute stroke care. Larger prospective studies are needed to validate these findings and to further refine treatment strategies. Full article

This study uses life cycle analysis (LCA) to evaluate the environmental impacts of co-firing bituminous coal with agricultural biomass waste, such as coconut and rice husks, emphasising circular economy principles. Seven experimental scenarios with different coal-to-biomass ratios were designed, ranging from pure coal to pure biomass. The results show that Scenario B (100% rice husk) achieved the best overall environmental performance, with the lowest global warming potential (300 kg CO₂ equivalent), eutrophication potential (4.742 kg PO₄ equivalent), and smog formation potential (0.012 kg C₂H₄ equivalent). Additionally, Scenario F (15% biomass mix) recorded the lowest acidification potential (57.39 kg SO₂ eq), indicating that even partial substitution can yield significant environmental benefits. In contrast, Scenario C (100% coal) exhibited the highest acidification (164.08 kg SO₂ eq) and eutrophication (8.82 kg PO₄ eq) potential. Overall, the results demonstrate that co-firing biomass waste significantly reduces pollutant emissions compared to burning coal alone. This study highlights the effectiveness of biomass waste co-firing in mitigating environmental impacts, promoting resource recovery, and supporting a sustainable energy transition within a circular economy framework. Full article

Posidonia oceanica seagrass, endemic to the Mediterranean Sea, provides ecological goods and ecosystem services of paramount importance. In shallow and sheltered bays, P. oceanica meadows can reach the sea surface, with leaf tips slightly emerging, forming fringing and barrier reefs. During the 20th century, P. oceanica declined conspicuously in the vicinity of large ports and urbanized areas, particularly in the north-western Mediterranean. The main causes of decline are land reclamation, anchoring, bottom trawling, turbidity and pollution. Artificial sand nourishment of beaches has also been called into question, with sand flowing into the sea, burying and destroying neighbouring meadows. A fringing reef of P. oceanica, located at Saint-Mandrier-sur-Mer, near the port of Toulon (Provence, France), is severely degraded. Analysis of aerial photos shows that, since the beginning of the 2000s, it has remained stable in some parts or continued to decline in others. This contrasts with the trend towards recovery, observed in France, thanks to e.g., the legally protected status of P. oceanica, and the reduction of pollution and coastal developments. The sand nourishment of the study beach, renewed every year, with the sand being washed or blown very quickly (within a few months) from the beach into the sea, burying the P. oceanica meadow, seems the most likely explanation. Other factors, such as pollution, trampling by beachgoers and overgrazing, may also play a role in the decline. Full article

Camellia oleifera, a woody oilseed species endemic to China, often experiences growth constraints due to seasonal drought. This study investigates the coordinated regulation of photosynthetic traits, stomatal behavior, and hormone responses during drought–rehydration cycles in two cultivars with contrasting drought resistance: ‘CL53’ (tolerant) and ‘CL40’ (sensitive). Photosynthetic inhibition resulted from both stomatal and non-stomatal limitations, with cultivar-specific differences. After 28 days of drought, the net photosynthetic rate (P_n) declined by 26.6% in CL53 and 32.6% in CL40. A stable intercellular CO₂ concentration (C_i) in CL53 indicated superior mesophyll integrity and antioxidant capacity. CL53 showed rapid P_n recovery and photosynthetic compensation post-rehydration, in contrast to CL40. Drought triggered extensive stomatal closure; >98% reopened upon rehydration, though the total stomatal pore area remained reduced. Abscisic acid (ABA) accumulation was greater in CL40, contributing to stomatal closure and P_n suppression. CL53 exhibited faster ABA degradation and gibberellin (GA₃) recovery, promoting photosynthetic restoration. ABA negatively correlated with P_n, transpiration rate (T_r), stomatal conductance (G_s), and C_i, but positively with stomatal limitation (L_s). Water use efficiency (WUE) displayed a parabolic response to ABA, differing by cultivar. This integrative analysis highlights a coordinated photosynthesis–stomata–hormone network underlying drought adaptation and informs selection strategies for drought-resilient cultivars and precision irrigation. Full article

This study investigates the behavior of phosphate ion transport through two structurally distinct anion-exchange membranes—AMV (homogeneous) and HC-A (heterogeneous)—in an electrodialysis system under both static and stirred conditions at varying pH levels. Chronopotentiometric and current–voltage analyses were used to investigate the influence of pH and hydrodynamics on ion transport. Under underlimiting (ohmic) conditions, the AMV membrane exhibited simultaneous transport of H₂PO₄⁻ and HPO₄²⁻ ions at neutral and mildly alkaline pH, while such behavior was not verified at acidic pH and in all cases for the HC-A membrane. Under overlimiting current conditions, AMV favored electroconvection at low pH and exhibited significant water dissociation at high pH, leading to local pH shifts and chemical equilibrium displacement at the membrane–solution interface. In contrast, the HC-A membrane operated predominantly under strong electroconvective regimes, regardless of the pH value, without evidence of water dissociation or equilibrium change phenomena. Stirring significantly impacted the electrochemical responses: it altered the chronopotentiogram profiles through the emergence of intense oscillations in membrane potential drop at overlimiting currents and modified the current–voltage behavior by increasing the limiting current density, reducing electrical resistance, and compressing the plateau region that separates ohmic and overlimiting regimes. Additionally, both membranes showed signs of NH₃ formation at the anodic-side interface under pH 7–8, associated with increased electrical resistance. These findings reveal distinct ionic transport characteristics and hydrodynamic sensitivities of the membranes, thus providing valuable insights for optimizing phosphate recovery via electrodialysis. Full article

Introduction: Given the impact of aneurysmal subarachnoid hemorrhage (aSAH) on patients’ health, preclinical research is substantial to understand its pathophysiology and improve treatment strategies, which necessitates reliable and comprehensive animal models. Traditionally, aSAH models utilize iliac or subclavian access for angiography, requiring invasive procedures that are associated with significant risks and animal burden. This pilot study explores a less invasive method of digital subtraction angiography (DSA) by using the auricular artery (AA) as an alternative access point. Our aim was to demonstrate the feasibility of this refined technique, with the intention of reducing procedural risks, providing shorter operation times with enhanced neurological recovery, and simplifying the process for both researchers and animals. Materials and Methods: In this study, six female New Zealand white rabbits (3.2–4.1 kg body weight) underwent experimental induction of aSAH via a subclavian-cisternal shunt. The initial steps of this procedure followed traditional techniques, consisting of subclavian access through microsurgical preparation, followed by DSA to analyze retrograde filling of the basilar artery (BA). To evaluate the alternative method, on day 3 after induction of aSAH, DSA was performed via the AA instead of the traditional subclavian or femoral access. A catheter was placed in the AA to allow retrograde filling of the BA. This approach aimed to simplify the procedure while maintaining comparable imaging quality. Results: All rabbits survived until the study endpoint. Postoperatively, two rabbits showed signs of hemisyndrome, which significantly improved by the time of follow-up. No additional morbidities were observed. Upon euthanasia and necropsy, all animals showed clear subarachnoid bleeding patterns. DSA via the AA produced strong contrasting of the BA comparable to the traditional method. Conclusions: This technical note presents an initial evaluation of AA access as a feasible and potentially advantageous method for DSA in a rabbit model of blood shunt subarachnoid hemorrhage. The method shows promise in reducing invasiveness and procedural complexity, but further studies are required to fully establish its efficacy and safety. Future research should focus on expanding the sample size, refining the anatomical understanding of the AA, and continuing to align with ethical considerations regarding animal welfare. Full article

This study examines the impact of free trade zone (FTZ) establishment on regional economic resilience (RER) in China, using provincial-level panel data spanning from 2010 to 2022 and a multi-period difference-in-differences (DID) approach. The empirical results indicate that FTZ implementation significantly enhances regional economic resilience by 3.46%, with the development of green finance acting as a key moderating mechanism that amplifies this positive effect. Heterogeneity analysis uncovers notable disparities across policy cohorts and geographical regions: the first wave of FTZs demonstrates the most pronounced resilience-enhancing impact, whereas later cohorts exhibit weaker or even adverse effects. Coastal regions experience substantial benefits from FTZ policies, in contrast to statistically insignificant outcomes observed in inland areas. These findings suggest that strategically expanding the FTZ network, when paired with tailored implementation mechanisms and the integration of green finance, could serve as a powerful policy tool for post-COVID economic recovery. Importantly, by strengthening economic resilience through institutional openness and green investment, this study offers valuable insights into balancing economic growth with environmental sustainability. It provides empirical evidence to support the optimization of FTZ spatial governance and institutional innovation pathways, thereby contributing to the pursuit of sustainable regional development. Full article

Alperujo, a solid by-product from the two-phase olive oil extraction process, poses significant environmental challenges due to its high organic load, phytotoxicity, and phenolic content. At the same time, it represents a promising feedstock for recovering value-added compounds such as phenols and volatile fatty acids (VFAs). When used as a substrate for white rot fungi (WRF), it also produces ligninolytic enzymes. This study explores the use of two native WRF, Anthracophyllum discolor and Stereum hirsutum, for the biotransformation of alperujo under solid-state fermentation conditions, with and without supplementation of copper and manganese, two cofactors known to enhance fungal enzymatic activity. S. hirsutum stood out for its ability to release high concentrations of phenolic compounds (up to 6001 ± 236 mg gallic acid eq L⁻¹) and VFAs (up to 1627 ± 325 mg L⁻¹) into the aqueous extract, particularly with metal supplementation. In contrast, A. discolor was more effective in degrading phenolic compounds within the solid matrix, achieving a 41% reduction over a 30-day period. However, its ability to accumulate phenolics and VFAs in the extract was limited. Both WRF exhibited increased enzymatic activities (particularly Laccase and Manganese Peroxidase) with the addition of Cu-Mn, highlighting the potential of the aqueous extract as a natural source of biocatalysts. Phytotoxicity assays using Solanum lycopersicum seeds confirmed a partial detoxification of the treated alperujo. However, none of the fungi could entirely eliminate inhibitory effects on their own, suggesting the need for complementary stabilization steps before agricultural reuse. Overall, the results indicate that S. hirsutum, especially when combined with metal supplementation, is better suited for valorizing alperujo through the recovery of bioactive compounds. Meanwhile, A. discolor may be more suitable for detoxifying the solid phase strategies. These findings support the integration of fungal pretreatment into biorefinery schemes that valorize agroindustrial residues while mitigating environmental issues. Full article

Background: Persistent neuromuscular deficits following anterior cruciate ligament reconstruction (ACLR) are frequently attributed to arthrogenic muscle inhibition (AMI). The type of autologous graft used may influence the trajectory of neuromuscular recovery. Objective: To investigate the influence of graft type—bone–patellar tendon–bone (BPTB), hamstring tendon (HT), and quadriceps tendon (QT)—on the contractile properties of periarticular knee muscles over a 9-month post-operative period. Hypothesis: Each graft type would result in distinct recovery patterns of muscle contractility, as measured by tensiomyography (TMG). Methods: Thirty-one patients undergoing ACLR with BPTB (n = 8), HT (n = 12), or QT (n = 11) autografts were evaluated at 3, 6, and 9 months post-operatively. TMG was used to measure contraction time (Tc) and maximal displacement (Dm) in the rectus femoris, vastus medialis, vastus lateralis, and biceps femoris. Results: Significant within-group improvements in Tc and Dm were observed across all graft types from 3 to 9 months (Tc: p < 0.001 to p = 0.02; Dm: p < 0.001 to p = 0.01). The QT group showed the most pronounced Tc reduction in RF (from 30.16 ± 2.4 ms to 15.44 ± 1.6 ms, p < 0.001) and VM (from 31.05 ± 2.6 ms to 18.65 ± 1.8 ms, p = 0.004). In contrast, HT grafts demonstrated limited Tc recovery in BF between 6 and 9 months compared to BPTB and QT (p < 0.001), indicating a stagnation phase. BPTB exhibited persistent bilateral deficits in both quadriceps and BF at 9 months. Conclusions: Autograft type significantly influences neuromuscular recovery patterns after ACLR. TMG enables objective, muscle-specific monitoring of contractile dynamics and may support future individualized rehabilitation strategies. Full article

Background/Objectives: Multimodal large language models (LLMs) are increasingly used in radiology. However, their ability to recognize fundamental imaging features, including modality, anatomical region, imaging plane, contrast-enhancement status, and particularly specific magnetic resonance imaging (MRI) sequences, remains underexplored. This study aims to evaluate and compare the performance of three advanced multimodal LLMs (ChatGPT-4o, Claude 4 Opus, and Gemini 2.5 Pro) in classifying brain MRI sequences. Methods: A total of 130 brain MRI images from adult patients without pathological findings were used, representing 13 standard MRI series. Models were tested using zero-shot prompts for identifying modality, anatomical region, imaging plane, contrast-enhancement status, and MRI sequence. Accuracy was calculated, and differences among models were analyzed using Cochran’s Q test and McNemar test with Bonferroni correction. Results: ChatGPT-4o and Gemini 2.5 Pro achieved 100% accuracy in identifying the imaging plane and 98.46% in identifying contrast-enhancement status. MRI sequence classification accuracy was 97.7% for ChatGPT-4o, 93.1% for Gemini 2.5 Pro, and 73.1% for Claude 4 Opus (p < 0.001). The most frequent misclassifications involved fluid-attenuated inversion recovery (FLAIR) sequences, often misclassified as T1-weighted or diffusion-weighted sequences. Claude 4 Opus showed lower accuracy in susceptibility-weighted imaging (SWI) and apparent diffusion coefficient (ADC) sequences. Gemini 2.5 Pro exhibited occasional hallucinations, including irrelevant clinical details such as “hypoglycemia” and “Susac syndrome.” Conclusions: Multimodal LLMs demonstrate high accuracy in basic MRI recognition tasks but vary significantly in specific sequence classification tasks. Hallucinations emphasize caution in clinical use, underlining the need for validation, transparency, and expert oversight. Full article

The Inner Mongolia Plateau (IMP), situated in the arid and semi-arid ecological transition zone of northern China, is particularly vulnerable to both climate change and human activities. Understanding the spatiotemporal vegetation dynamics and their driving forces is essential for regional ecological management. This study employs Sen’s slope estimation, BFAST analysis, residual trend method and Geodetector to analyze the spatial patterns of Normalized Difference Vegetation Index (NDVI) variability and distinguish between climatic and anthropogenic influences. Key findings include the following: (1) From 1982 to 2022, vegetation cover across the IMP exhibited a significant greening trend. Zonal analysis showed that this spatial heterogeneity was strongly regulated by regional hydrothermal conditions, with varied responses across land cover types and pronounced recovery observed in high-altitude areas. (2) In the western arid regions, vegetation trends were unstable, often marked by interruptions and reversals, contrasting with the sustained greening observed in the eastern zones. (3) Vegetation growth was primarily temperature-driven in the eastern forested areas, precipitation-driven in the central grasslands, and severely limited in the western deserts due to warming-induced drought. (4) Human activities exerted dual effects: significant positive residual trends were observed in the Hetao Plain and southern Horqin Sandy Land, while widespread negative residuals emerged across the southern deserts and central grasslands. (5) Vegetation change was driven by climate and human factors, with recovery mainly due to climate improvement and degradation linked to their combined impact. These findings highlight the interactive mechanisms of climate change and human disturbance in regulating terrestrial vegetation dynamics, offering insights for sustainable development and ecosystem education in climate-sensitive systems. Full article

The recovery and abatement of volatile organic compounds (VOCs) have received increasing attention due to their significant environmental and health impacts. Supported sulfonic acid materials have shown great potential in converting aromatic VOCs into their non-volatile derivatives through reactive adsorption. However, the anchoring state of sulfonic acid groups, which is closely related to the properties of the support, greatly affects their performance. In this study, two supported sulfonic acid materials, SZO and SMO, were prepared by treating ZrO₂ and MgO with chlorosulfonic acid, respectively, to investigate the influence of the support properties on the anchoring state of sulfonic acid groups and their reactive adsorption performance for o-xylene. The supports, adsorbents, and adsorption products were extensively characterized, and the reactivity of SZO and SMO towards o-xylene was systematically compared. The results showed that sulfonic acid groups are anchored on the ZrO₂ surface through covalent bonding, forming positively charged sulfonic acid sites ([O_1.5Zr-O]^δ−-SO3H^δ+) with a loading of 3.6 mmol/g. As a result, SZO exhibited excellent removal efficiency (≥91.3%) and high breakthrough adsorption capacity (ranging from 38.59 to 82.07 mg/g) for o-xylene in the temperature range of 130 –150 °C. In contrast, sulfonic acid groups are anchored on the MgO surface via ion-paired bonding, leading to the formation of negatively charged sulfonic acid sites ([O_0.5Mg]⁺:OSO₃H⁻), which prevents their participation in the electrophilic sulfonation reaction with o-xylene molecules. This work provides new insights into tuning and enhancing the performance of supported sulfonic acid materials for the resource-oriented treatment of aromatic VOCs. Full article