Search Results (644)

Severe polysulfide shuttling and sluggish redox kinetics critically hinder lithium–sulfur (Li-S) battery commercialization. In this study, a multifunctional diatomite (DE)/TiO₂/MoS₂/N-doped carbon nanofiber (NCNF) composite separator was fabricated via hydrothermal synthesis, electrospinning, and carbonization. DE provides dual polysulfide suppression, encompassing microporous confinement and electrostatic repulsion. By integrating synergistic catalytic effects from TiO₂ and MoS₂ nanoparticles, which accelerate polysulfide conversion, and conductive NCNF networks, which facilitate rapid charge transfer, this hierarchical design achieves exceptional electrochemical performance: a 1245.6 mAh g⁻¹ initial capacity at 0.5 C and 65.94% retention after 200 cycles. This work presents a rational multi-component engineering strategy to suppress shuttle effects in high-energy-density Li-S batteries. Full article

The widespread adoption of sodium-ion batteries (SIBs) remains constrained by the inherent limitations of conventional anode materials, particularly their inadequate electronic conductivity, limited active sites, and pronounced structural degradation during cycling. To overcome these limitations, we propose a novel redox engineering approach to fabricate oxygen-vacancy-rich SnO₂ dots anchored on reduced graphene oxide (rGO), which are encapsulated within N-doped carbon nanofibers (denoted as ov-SnO₂/rGO@N-CNFs) through electrospinning and subsequent carbonization. The introduction of rich oxygen vacancies establishes additional sodium intercalation sites and enhances Na⁺ diffusion kinetics, while the conductive N-doped carbon network effectively facilitates charge transport and mitigates SnO₂ aggregation. Benefiting from the well-designed architecture, the hierarchical ov-SnO₂/rGO@N-CNFs electrode achieves remarkable reversible specific capacities of 351 mAh g⁻¹ after 100 cycles at 0.1 A g⁻¹ and 257.3 mAh g⁻¹ after 2000 cycles at 1.0 A g⁻¹ and maintains 177 mAh g⁻¹ even after 8000 cycles at 5.0 A g⁻¹, demonstrating exceptional long-term cycling stability and rate capability. This work offers a versatile design strategy for developing high-performance anode materials through synergistic interface engineering for SIBs. Full article

Room-temperature vulcanizing (RTV) silicone foams are used in many industrial applications that require the material to perform over long time periods. However, mechanical properties tend to deteriorate when these foams age under a compressive load. The chemical aging is attributed to the presence of unreacted functional groups of the prepolymers, residues from acid, and catalytically active tin (II) species. Here, an optimized thermal treatment of an RTV foam that achieves completion of curing reactions and deactivation of reactive species is proposed. Foams that were thermally aged for three months under compressive load showed no signs of compression set, indicative of the effectiveness of the implemented post-curing approach. In addition, the effects of fillers (diatomaceous earth, fumed silica, and carbon nanofibers) on thermomechanical properties were investigated. Tensile strength, tear strength, and thermal conductivity increased when these fillers were added to the unfilled RTV formulation, with carbon nanofibers (CNFs) being the most effective filler. Rheological studies of RTV formulations indicated that 2.5 wt.% of CNFs is the upper limit that can be added to the RTV formulation. Full article

Herein, electrospun nanofibers composed of polyaniline (PANI), polyethylene oxide (PEO), and Luffa cylindrica (LC) cellulose, reinforced with titanium dioxide (TiO₂) nanoparticles, were synthesized via electrospinning to investigate the effect of TiO₂ nanoparticles on PANI/PEO/LC nanocomposites and the effect of conductivity on nanofiber morphology. Cellulose extracted from luffa was added to the PANI/PEO copolymer solution, and two different ratios of TiO₂ were mixed into the PANI/PEO/LC biocomposite. The morphological, vibrational, and thermal characteristics of biocomposites were systematically investigated using scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). As anticipated, the presence of TiO₂ enhanced the electrical conductivity of biocomposites, while the addition of Luffa cellulose further improved the conductivity of the cellulose-based nanofibers. FTIR analysis confirmed chemical interactions between Luffa cellulose and PANI/PEO matrix, as evidenced by the broadening of the hydroxyl (OH) absorption band at 3500–3200 cm⁻¹. Additionally, the emergence of characteristic peaks within the 400–1000 cm⁻¹ range in the PANI/PEO/LC/TiO₂ spectra signified Ti–O–Ti and Ti–O–C vibrations, confirming the incorporation of TiO₂ into the biocomposite. SEM images of the biocomposites reveal that the thickness of nanofibers decreases by adding Luffa to PANI/PEO nanofibers because of the nanofibers branching. In addition, when blending TiO₂ nanoparticles with the PANI/PEO/LC biocomposite, this increment continued and obtained thinner and smother nanofibers. Furthermore, the incorporation of cellulose slightly improved the crystallinity of the nanofibers, while TiO₂ contributed to the enhanced crystallinity of the biocomposite according to the XRD and DCS results. Similarly, the TGA results supported the DSC results regarding the increasing thermal stability of the biocomposite nanofibers with TiO₂ nanoparticles. These findings demonstrate the potential of PANI/PEO/LC/TiO₂ nanofibers for advanced applications requiring conductive and structurally optimized biomaterials, e.g., for use in humidity or volatile organic compound (VOC) sensors, especially where flexibility and environmental sustainability are required. Full article

Planar heaters are designed to deliver uniform heat across broad surfaces and serve as critical components in applications requiring energy efficiency, safety, and mechanical flexibility, such as wearable electronics and smart textiles. However, conventional metal-based heaters are limited by poor adaptability to curved or complex surfaces, low mechanical compliance, and susceptibility to oxidation-induced degradation. To overcome these challenges, we applied a protein-assisted electroless copper (Cu) plating strategy to electrospun poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) nanofiber substrates to fabricate flexible, conductive planar heating membranes. For interfacial functionalization, a protein-based engineering approach using bovine serum albumin (BSA) was employed to facilitate palladium ion coordination and seed formation. The resulting membrane exhibited a dense, continuous Cu coating, low sheet resistance, excellent durability under mechanical deformation, and stable heating performance at low voltages. These results demonstrate that the BSA-assisted strategy can be effectively extended to complex three-dimensional fibrous membranes, supporting its scalability and practical potential for next-generation conformal and wearable planar heaters. Full article

This study presents the development and characterization of electrospun nanofibers composed of polyvinyl alcohol (PVA) and natural beeswax (BW). A stable emulsion containing 9 wt% PVA and 5 wt% BW was successfully formulated and electrospun. The effects of beeswax incorporation on solution properties-viscosity, conductivity, and surface tension—were systematically evaluated. Electrospinning was performed at 30 kV and a working distance of 14.5 cm, yielding nanofibers with diameters between 125 and 425 nm. Scanning electron microscopy (SEM) revealed increased surface roughness and diameter variability in PVA/BW fibers compared to the PVA. Fourier transform infrared spectroscopy (FTIR) confirmed physical incorporation of BW without evidence of chemical bonding. Thermogravimetric and differential scanning calorimetry analyses (TGA/DSC) demonstrated altered behavior and an expanded profile of temperature transitions due to the waxy components. The solubility test of the nanofiber mat in saline indicated that BW slows dissolution and improves the structural integrity of the fibers. This study demonstrates, for the first time, the incorporation of beeswax into electrospun PVA nanofibers with improved structural and thermal properties, indicating potential for further exploration in biomedical material design. Full article

Celiac disease (CD), a human leukocyte antigen-associated disorder, is caused by gluten sensitivity and is characterized by mucosal alterations in the small intestine. Currently, its diagnosis involves the determination of serological markers. The traditional method for clinically determining these markers is the enzyme-linked immunosorbent assay. However, immunosensors offer sensitivity and facilitate the development of miniaturized and portable analytical systems. This work focuses on developing an amperometric immunosensor for the quantification of IgA antibodies against tissue transglutaminase (IgA anti-TGA) in human serum samples, providing information on a critical biomarker for CD diagnosis. The electrochemical device was designed on a polyimide substrate using a novel solid ink of wax and carbon nanofibers (CNFs). The working electrode microzone was defined by incorporating aminofunctionalized TiO₂ nanoparticles (TiO₂NPs). The interactions and morphology of CNFs/wax and TiO₂NPs/CNFs/wax electrodes were assessed through different characterization techniques. Furthermore, the device was electrochemically characterized, demonstrating that the incorporation of CNFs into the wax matrix significantly enhanced its conductivity and increased the active surface area of the electrode, while TiO₂NPs contributed to the immunoreaction area. The developed device exhibited remarkable sensitivity, selectivity, and reproducibility. These results indicate that the fabricated device is a robust and reliable tool for the precise serological diagnosis of CD. Full article

Lithium–sulfur batteries (LSBs), possessing excellent theoretical capacities, advanced theoretical energy densities, low cost, and nontoxicity, are one of the most promising energy storage battery systems. However, some issues, including poor conductivity of elemental S, the “shuttle effect” of high-order lithium polysulfides (LiPSs), and sluggish reaction kinetics, hinder the commercialization of LSBs. To solve these problems, various carbon-based aerogels with developed surface morphology, tunable pores, and electrical conductivity have been examined for immobilizing sulfur, mitigating its volume variation and enhancing its electrochemical kinetics. In this paper, an extensive generalization about the effective preparation methods of carbon-based aerogels comprising the combined method of carbonization with the gelation of precursors and drying processes (ambient pressure drying, freeze-drying, and supercritical drying) is proposed. And we summarize various carbon carbon-based aerogels, mainly including graphene aerogels (Gas) and carbon nanofiber (CNF) and carbon nanotube (CNT) aerogels as cathodes, separators, and interlayers in LSBs. In addition, the mechanism of action of carbon-based aerogels in LSBs is described. Finally, we conclude with an outlook section to provide some insights into the application of carbon-based aerogels in electrochemical energy storage devices. Based on the discussion and proposed recommendations, we provide more approaches on nanomaterials in high-performance liquid or state LSBs with high electrochemical performance in the future. Full article

Fibrous structure is a promising building block for developing high-performance wearable piezoresistive sensors. However, the inherent non-conductivity of the fibrous polymer remains a bottleneck for highly sensitive and fast-responsive piezoresistive sensors. Herein, we reported a polyaniline/reduced graphene oxide @ polydopamine/poly (vinylidene fluoride) (PANI/rGO@PDA/PVDF) nanofiber piezoresistive sensor (PNPS) capable of versatile wearable biomonitoring. The PNPS was fabricated by integrating rGO sheets and PANI particles into a PDA-modified PVDF nanofiber network, where PDA was implemented to boost the interaction between the nanofiber networks and functional materials, PANI particles were deposited on a nanofiber substrate to construct electroactive nanofibers, and rGO sheets were utilized to interconnect nanofibers to strengthen in-plane charge carrier transport. Benefitting from the synergistic effect of multi-dimensional electroactive materials in piezoresistive membranes, the as-fabricated PNPS exhibits a high sensitivity of 13.43 kPa⁻¹ and a fast response time of 9 ms, which are significantly superior to those without an rGO sheet. Additionally, a wide pressure detection range from 0 to 30 kPa and great mechanical reliability over 12,000 cycles were attained. Furthermore, the as-prepared PNPS demonstrated the capability to detect radial arterial pulses, subtle limb motions, and diverse respiratory patterns, highlighting its potential for wearable biomonitoring and healthcare assessment. Full article

This study presents a one-step electrospinning method to fabricate polyacrylonitrile (PAN) nanofibers embedded with green-synthesized silver nanoparticles (AgNPs) for efficient catalytic dye reduction and real-time monitoring. Utilizing avocado seed extract for AgNP synthesis, the resulting composite nanofibers exhibit uniform nanoparticle dispersion and enhanced surface area, significantly improving adsorption and catalytic properties. The membranes demonstrated outstanding catalytic activity, achieving over 95% degradation of methyl orange within 45 min when paired with sodium borohydride, and maintained structural integrity and performance over ten reuse cycles. The integration of a novel 3D-printed support enabled scalability, allowing a 60-fold increase in treatment volume without compromising efficiency. Additionally, the composite’s electrical conductivity changes enabled the real-time monitoring of the dye reduction process, highlighting its dual functionality as both catalyst and sensor. These results encourage the potential of PAN/AgNPs supported on a 3D-printed structure nanofiber membranes for scalable, sustainable wastewater treatment and in situ reaction monitoring. Full article

This review is different from previous studies focusing on polypyrrole (PPy) in universal fields such as sensors and supercapacitors. It is the first TO systematically review the specific applications of PPy-based electrospun nanofiber composites in the biomedical field, focusing on its biocompatibility regulation mechanism and tissue repair function. Although PPy exhibits exceptional electrical conductivity, redox activity, and biocompatibility, its clinical translation is hindered by processing challenges and poor degradability. These limitations can be significantly mitigated through composite strategies with degradable nanomaterials, enhancing both process compatibility and biofunctionality. Leveraging the morphological similarity between electrospun nanofibers and the natural extracellular matrix (ECM), this work comprehensively analyzes the topological characteristics of three composite fiber architectures—randomly distributed, aligned, and core–shell structures—and elucidates their application mechanisms in nerve regeneration, skin repair, bone mineralization, and myocardial tissue reconstruction (e.g., facilitating oriented cell migration and regulating differentiation through specific signaling pathway activation). The study further highlights critical challenges in the field, including PPy’s poor solubility, limited spinnability, insufficient mechanical strength, and scalability limitations. Future efforts should prioritize the development of multifunctional gradient composites, intelligent dynamic-responsive scaffolds, and standardized biosafety evaluation systems to accelerate the substantive translation of these materials into clinical applications. Full article

Chlorpheniramine maleate (CPM) is a first-generation antihistamine that is frequently used to treat allergic reactions. However, excessive consumption presents potential health risks. Therefore, it is crucial to develop a quick and precise technique for identifying CPM levels. In this study, nickel cobalt phosphide (NiCoP), a binary metal phosphide, was successfully incorporated into carbon nanofibers. This involved creating a pore structure by adding polyvinylpyrrolidone (PVP) as a pore-forming template to a polyacrylonitrile (PAN) substrate via electrostatic spinning. An innovative electrochemiluminescent sensor for CPM detection was constructed using NiCoP/PVP/PAN carbon nanofibers (NiCoP/PVP/PAN/CNFs). Under optimal conditions, the electrochemical behavior of CPM was studied using NiCoP/PVP/PAN/CNF-modified working electrodes. These findings demonstrate that the three-dimensional porous network architecture of NiCoP/PVP/PAN/CNFs enhances the conductive properties of the material. Consequently, an electrochemical optical sensor fabricated using this structure exhibited remarkable performance. The linear detection range of the sensor was 1 × 10⁻⁸–7 × 10⁻⁵ mol/L, and the detection limit was 7.8 × 10⁻¹⁰ mol/L. When human urine and serum samples were examined, the sensor was found to have a high recovery rate (94.35–103.36%), which is promising for practical applications. Full article

Anion exchange membrane fuel cells (AEMFCs) have garnered significant attention for their potential to advance fuel cell technology. In this study, we developed and characterized anion exchange membranes (AEMs) composed of quaternized poly(vinyl alcohol) (QPVA) electrospun nanofiber mats with poly(acrylamide-co-diallyldimethylammonium chloride) (PAADDA) as a matrix filler for interfiber voids. The objective was to investigate the effect of varying PAADDA concentrations as a matrix filler for interfiber voids on the structural, mechanical, and electrochemical properties of QPVA-based electrospun AEMs. Membranes with various concentrations of PAADDA were fabricated and extensively characterized using FTIR, SEM, tensile strength, water uptake, swelling degree, ion exchange capacity (IEC), and hydroxide ion conductivity (σ). FTIR confirmed the successful incorporation of PAADDA into the membrane structure, while SEM images showed that PAADDA effectively filled the voids between the QPVA fibers, resulting in denser membranes. The results indicated that the eQPAD5.0 membrane, with the highest PAADDA content, exhibited the best overall performance. The incorporation of PAADDA into QPVA-based electrospun AEMs significantly enhanced their mechanical strength, achieving a tensile strength of 23.9 MPa, an IEC of 1.25 mmol g⁻¹, and hydroxide conductivity of 19.49 mS cm⁻¹ at 30 °C and 29.29 mS cm⁻¹ at 80 °C, making them promising candidates for fuel cell applications. Full article

Advancements in thermoregulating textiles have been propelled by innovations in nanotechnology, composite materials, and smart fiber engineering. This article reviews recent scholarly papers on experimental passive and active thermoregulating textiles to present the latest advancements in these fabrics, their mechanisms of thermoregulation, and their feasibility for use. The review underscores that phase-change materials enhanced with graphene, boron nitride, and carbon nanofibers offer superior thermal conductivity, phase stability, and flexibility, making them ideal for wearable applications. Shape-stabilized phase-change materials and aerogel-infused fibers have shown promising results in outdoor, industrial, and emergency settings due to their durability and high insulation efficiency. Radiative cooling textiles, engineered with hierarchical nanostructures and Janus wettability, demonstrate passive temperature regulation through selective solar reflection and infrared emission, achieving substantial cooling effects without external energy input. Thermo-responsive, shape-memory materials, and moisture-sensitive polymers enable dynamic insulation and actuation. Liquid-cooling garments and thermoelectric hybrids deliver precise temperature control but face challenges in portability and power consumption. While thermoregulating textiles show promise, the main challenges include achieving scalable manufacturing, ensuring material flexibility, and integrating multiple functions without sacrificing comfort. Future research should focus on hybrid systems combining passive and active mechanisms, user-centric wearability studies, and cost-effective fabrication methods. These innovations hold significant potential for applications in extreme environments, athletic wear, military uniforms, and smart clothing, contributing to energy efficiency, health, and comfort in a warming climate. Full article

Nanofibers have emerged as transformative materials in the field of energy storage, offering unique physicochemical properties such as high surface area, porosity, and tunable morphology. Recent advancements have also introduced genetically modified fibers—engineered at the biological level to produce functionalized nanostructures with customizable properties. These bioengineered nanofibers add a sustainable and potentially self-healing component to energy storage materials. This paper reviews key applications of conventional and genetically modified nanofibers in lithium-ion and sodium-ion batteries, supercapacitors, hybrid systems, and flexible energy storage with a focus on how genetic and molecular engineering of fibrous materials enables new capabilities in ion transport, electrode architecture, and device longevity. Together, these advances contribute to the development of next-generation energy storage systems with enhanced performance, biocompatibility, and sustainability. This review therefore critically examines the current state, advantages, and limitations of both synthetic and biopolymer-based materials in energy storage applications. It discusses recent technological innovations, such as polymer–nanoparticle composites, functionalized polymer matrices, and next-generation polymer electrolytes. Future research should prioritize enhancing conductivity, improving scalability, and reducing environmental impact, ensuring that polymer-based materials contribute to the development of more efficient and sustainable energy storage technologies. Full article