Search Results (32)

The scaphoid is the most commonly fractured carpal bone. Headless compression screws became the gold standard for fixation, but the ideal screw diameter remains debated. This study investigates the relative benefit of using a larger screw diameter to improve stability in typical scaphoid fractures. It also examines the effects of preload and screw length on mechanical behaviour. A finite element (FE) model of a mid-waist scaphoid fracture was created. Screws from Medartis (1.7 mm, 2.2 mm, and 3.0 mm diameter; 23 mm length) were placed along the longitudinal axis. Boundary and loading conditions matched prior studies. Interfragmentary displacement (IFD) and von Mises stress were compared across screw sizes. The effects of screw length and preload were also evaluated. Maximum in-plane IFD was 2.08 mm (1.7 mm screw), 0.53 mm (2.2 mm), and 0.27 mm (3.0 mm). The 1.7 mm screw exceeded the scaphoid’s average ultimate stress (60.51 MPa). Increasing preload reduced IFD, especially above 60 N. Screws longer than 1.5 times the mid-waist diameter offered no added benefit. Larger screws provide better biomechanical fracture stability. However, the gain from 2.2 mm to 3.0 mm is minor, while 1.7 mm screws lack sufficient strength. The 2.2 mm screw offers a good balance of stability and bone preservation, making it the preferred choice. Full article

Objectives: Tibial apophysis avulsion fracture is an unusual injury in young pediatric athletes. The mechanism of injury is often related to sports (i.e football and basketball). Fifteen patients who had this kind of fracture underwent surgical Open Reduction and Internal Fixation (ORIF) with two or three cannulated screws and tendon stripping. In this kind of injury and treatment, one of the most important concerns is the recovery of the extensor apparatus strength of the lower limb. Materials and Methods: We followed up the patients for 12 months, performing biomechanical tests and a kinetic analysis to evaluate the activation of the leg muscles such as rectus femoris, vastus medialis, vastus lateralis, and semitendinosus muscle fibers and compared them with the contralateral healthy limb. Results: The results showed that there was an almost complete recovery of muscle strength activation without any statistically significant differences compared to the healthy limb. Conclusions: This surgical treatment appears to be safe and effective in the treatment of tibial apophysis fractures in young athletes, since this type of surgical treatment does not compromise the recovery of the extensor apparatus strength and/or return to sport of the lower limb in case of tibial apophysis fractures in young athletes. Full article

This study compares the compression force of cortical screws used in lag fashion with partially threaded cannulated screws and fully threaded headless cannulated screws as fixation methods for humeral condylar fractures in dogs. Cadavers of eleven dogs weighing an average of 10.99 ± 2.51 kg (6.1–14.4 kg) were used. The humeri were subjected to simulated fracture by performing an osteotomy at the trochlea of humerus and classified into three groups: Group 1 applied a 3.0 mm cortical screw applied in a lag fashion, Group 2 applied a 3.0 mm partially threaded cannulated screw, and Group 3 applied a 3.5 mm fully threaded headless cannulated screw. The samples were then placed in a material testing machine, and a compression force was applied vertically to the lateral condyle until failure. There were statistically significant differences in failure load between the groups (p = 0.009). The maximum failure load in Group 3 was significantly higher than in Group 2 (p = 0.014), while there were no statistically significant differences between Group 1 and Group 2) or between Group 1 and Group 3. Partially threaded cannulated screws and fully threaded headless cannulated screws can be alternatives to traditional stabilization methods, offering simpler procedures and additional advantages. Full article

A 3D-printed guide is an effective method for accurately placing pedicle screws in dog vertebrae. While a conventional drill guide allows precise pilot hole formation, it can lead to potential screw wobbling during insertion. In this study, we applied a technique that assists with both drilling and screw insertion, and we compared the accuracy of screw placement using this approach with that achieved by the conventional drill guide. The screws were divided into three groups: Group A (drill guide), Group B (cannulated guide), and Group C (screw guide). The accuracy of screw placement was assessed by comparing preoperative and postoperative CT images. Group A exhibited the largest angular deviation. Group C exhibited significantly smaller deviations in entry point, exit point, angle α, and angular deviation than Group A. In Group B, only the exit-point deviation was significantly smaller than that in Group A. Furthermore, the angular deviation in Group C was significantly smaller than that in Group B. In conclusion, 3D-printed screw-guiding techniques improved the accuracy of pedicle screw placement, with screw guides outperforming cannulated guides, making them a viable option for small breed dogs. Full article

Pediatric elbow fractures are quite common, accounting for up to 34% of bone fractures in children. Among these, acute lateral humeral condyle (LHC) fractures represent up to 22%. The accurate diagnosis and early treatment of LHC fractures are crucial due to the potential for abnormal growth and significant long-term impacts on joint motion. With the aim of enhancing the understanding of pediatric LHC fracture management among pediatric healthcare practitioners, we present a literature review combined with our technical recommendations based on our experience. Imaging through AP, lateral, and internal oblique X-rays remains the gold standard for diagnosis, although there is increasing focus on non-irradiating techniques, considering the skeletally immature nature of the patients. Several classification systems aid in fracture assessment, each varying in their simplicity, reproducibility, and inter- and intra-observer correlations. The treatment approaches for LHC fractures include conservative management with immobilization for minimally displaced fractures and surgical intervention for displaced fractures. The surgical options encompass closed and open reductions, using Kirschner wires or cannulated screws for fixation. While both methods show favorable outcomes, recent years have seen a growing interest in expanding the traditional indications for closed approaches. After a period of post-surgical immobilization of the limb, rehabilitation care is recommended to assist in the recovery of the range of motion. During the postoperative period, the most frequent complications are bony overgrowth, malunion, and infection, although with highly variable rates, which typically do not result in functional impairment if managed properly. Regular follow-up and monitoring are essential for optimal recovery and minimizing long-term complications. Full article

We report two rare cases of femoral neck fracture resulting from osteonecrosis of the femoral head (ONFH) that was undiagnosed at the patients’ initial visits. The patient in the first case had sequential bilateral displaced femoral neck fractures. Because no osteonecrosis of the femoral head was visible on X-ray film and the data of liver function tests were normal, ONFH was not diagnosed. In addition, because the patient was a 55-year-old man with normal everyday functioning, closed reduction with cannulated screws was performed at both visits. Nine months later, he came to our outpatient department with bilateral hip pain; X-rays revealed nonunion and implant failure at both hips. The patient subsequently underwent bilateral total hip arthroplasty (THA) and had a satisfactory outcome at his 4-year follow-up. The patient in the second case had a left displaced femoral neck fracture after trivial trauma two months prior. ONFH was not diagnosed upon examination of X-ray findings. The patient was 52 years old with liver cirrhosis and had bipolar hemiarthroplasty performed because of a chronic displaced fracture and poor general condition. After 2 years, she began to have right hip pain. X-rays revealed massive necrosis and sclerosis of the femoral head. Computed tomography scans for ONFH staging revealed impending fracture lines at the subcapital site of the patient’s previous left femoral neck fracture. Right THA was then performed, and the outcome was satisfactory. Full article

Introduction: Sacral fractures are rare but are increasing in incidence among trauma patients. They are associated with a wide variety of complications, most commonly neurologic defects. Case Report: A 59-year old woman initially underwent open reduction internal fixation (ORIF) for a sacral fracture, after which the patient developed an infection, wound complications, and hardware failure. The revision of the iliosacral screws proved challenging in that the standard screw and washer could not achieve sufficient compression of the fracture. Therefore, a modified midfoot mesh plate was cut to size and used as a washer to gain more surface area, achieving fixation. The plate was applied laterally and cut to cover as much surface area as possible without unnecessary bony overhang. A trans-iliac trans-sacral screw was then inserted in the standard fashion, thus allowing the plate to act as a washer. This resulted in an excellent outcome with appropriate fracture healing. Conclusion: We describe the case of an iliosacral screw revision in which a modified midfoot mesh plate was used as a washer. This resulted in appropriate fixation in the revision settings. The principles described to achieve this fixation can be broadly applied in the setting of orthopedic fractures. Full article

Background: The arthroscopically assisted stabilization of AC joint dislocations with a suture button system is an established procedure that is widely and successfully used in everyday practice. The main advantages of this one-step method are the minimally invasive procedure and the anatomical reconstruction of the ruptured coracoclavicular ligaments with a permanent implant. With this technical note study, for the first time, the new method of navigated suture button implantation in everyday clinical practice is described with the future goal of further reducing invasiveness and increasing precision. Materials and Methods: The surgical technique is explained using precise descriptions and illustrations, photos, X-rays, and 3D reconstructions based on clinical cases. The step-by-step system setup and patient positioning, AC joint reduction and retention, 3D scan and drill tunnel planning, stab incision and Kirschner wire navigation, and cannulated drilling and implant positioning, as well as closure and documentation are described in detail. Results: The standard coracoclavicular stabilization of AC joint dislocations with the 3D C-arm navigated suture button method is described in detail. Furthermore, the feasibility of an additive horizontal acromioclavicular suture cerclage, the implantation of an additional coracoclavicular suture button system, and the single-stage cannulated screw fixation of non-displaced fractures is demonstrated. Conclusion: The navigated suture button method aims to be simple, safe, minimally invasive, and precise. Prospective clinical studies with a long follow-up should be carried out to determine the clinical and radiological outcome in comparison with current methods. Full article

Background and Objectives: Despite the established role of subtalar joint arthrodesis (SJA) for treatment of subtalar osteoarthritis, achieving bone union remains challenging, with up to 46% non-union rates. Adequate compression and stable fixation are crucial for successful outcomes, with internal screw fixation being the gold standard for SJA. The delta configuration, featuring highly divergent screws, offers stability, however, it can result in hardware irritation in 20–30% of patients. Solutions to solve this complication include cannulated compression screw (CCS) countersinking or cannulated compression headless screw (CCHS) application. The aim of this biomechanical study was to investigate the stability of a delta configuration for SJA utilizing either a combination of a posterior CCHS and an anterior CCS or a standard two-CCS combination. Materials and Methods: Twelve paired human cadaveric lower legs were assigned pairwise to two groups for SJA using either two CCSs (Group 1) or one posterior CCHS and one anterior CCS (Group 2). All specimens were tested under progressively increasing cyclic loading to failure, with monitoring of the talocalcaneal movements via motion tracking. Results: Initial stiffness did not differ significantly between the groups, p = 0.949. Talocalcaneal movements in terms of varus–valgus deformation and internal–external rotation were significantly bigger in Group 1 versus Group 2, p ≤ 0.026. Number of cycles until reaching 5° varus–valgus deformation was significantly higher in Group 2 versus Group 1, p = 0.029. Conclusions: A delta-configuration SJA utilizing a posterior CCHS and an anterior CCS is biomechanically superior versus a standard configuration with two CCSs. Clinically, the use of a posterior CCHS could prevent protrusion of the hardware in the heel, while an anterior CCS could facilitate less surgical time and thus less complication rates. Full article

Introduction: Basicervical femoral neck fracture (FNF) is an uncommon type of femoral neck fracture and is associated with an increased risk of fixation failure due to its inherent instability. The purpose of this study was to compare the surgical parameters and reoperation rate between the use of a multiple cannulated screw (MCS) and fixed angle device (FAD) in treating basicervical FNFs. Methods: We retrospectively reviewed the records of 885 patients who underwent internal fixation between May 2004 and August 2019 to determine basicervical FNF with at least 12 months of follow-up. Among the identified 77 patients with basicervical FNF, 17 patients who underwent multiple cannulated screw (MCS) fixation and 36 patients who underwent fixed angle device (FAD) fixation were included. We compared the rates of fracture-site collapse and reoperations according to the fixation device. Results: Among the 53 patients with basicervical FNF, 13 patients (24.5%) sustained surgical complications (8 collapses of fracture site and 5 reoperations). The reoperation rate in the MCS group was significantly higher than that in the FAD group (23.5% vs. 2.8%, p = 0.016), without any significant difference in the collapse of the fracture site (11.8% vs. 16.7%, p = 0.642). Conclusions: Although basicervical FNF was rare among hip fractures, fracture site collapse was prevalent and prone to fixation failure. Surgeons should keep this in mind, and consider FAD for basicervical FNF. Full article

Triangular screw configuration (TSC) fixation is widely used in clinics for femoral neck fractures, and the appropriate positions of TSC fixation have not been fully described in the literature. This study investigated the optimal fixation of femoral neck fractures with TSC fixation under nonstandard Pauwels angles to determine the ideal position. To determine the optimal fracture line angle and cannulated screw positions, the Pauwels angle and Rotation and Translate variables were parametrically defined in the fracture line and cannulated screw positions. Considering the equivalent stresses on the fracture surfaces, the effectiveness values of the Rotation and Translate 1, 2 and 3 variables are weak, whereas the effectiveness value of the Pauwels angle is high. Considering the equivalent stress on the screws and that the variable value of Translates 1, 2 and 3 is 7 mm, it can be seen that the reverse triangulation configuration is better, and the Pauwels angle is approximately 54°. Among the parameters examined in the study, Pauwels angle was found to have the highest level of effectiveness on femoral neck fracture surfaces and screws. The findings in this study provide a solid basis for future research; however, further clinical research is warranted. Full article

Cannulated hip screws (CHS) can be used for the minimally invasive fixation of non-dislocated femoral neck fractures. Usually, three screws are inserted. This study aims to determine whether fixation by two CHS leads to similar results as fixation by three CHS. Since January 2019, all patients with an indication for internal fixation by CHS were treated with two CHS and followed prospectively. Results were compared to an equal-sized control group of patients who underwent fixation by three CHS (before 2019). The primary outcome was reoperation, while the secondary outcome was screw dislocation. Since January 2019, 50 patients were treated by two CHS. Of these, 14 patients (28%) underwent reoperation versus 13 patients (26%) in the control group (p = 1.000). Reoperations included screw replacement, hemiarthroplasty, and total hip prosthesis. Three major reasons for reoperation were pain due to osteosynthesis material (n = 15), coxarthrosis (n = 4), and screw cut out (n = 3). Six weeks postoperative X-rays showed a screw dislocation of 2 mm for the two CHS group and 1 mm for the three CHS group (p = 0.330). Clinical outcomes were very similar between the groups. The overall results were good; however, the reoperation rate varied from 26 to 28%. The majority of reoperations were screw replacements. Screw dislocation seems to be more prominent in patients treated with two screws (2 mm versus 1 mm). Fixation by two cannulated hip screws is an acceptable treatment method for non-dislocated femoral neck fractures, and the insertion of a third screw does not lead to superior clinical results. Full article

Introduction: Open reduction and reconstruction plate and screws fixation (RPSF) is considered the gold standard for the treatment of traumatic symphysis pubis diastasis (SPD). Percutaneous cannulated screw fixation (PCSF) has recently gained popularity as it may reduce operative time and morbidity. The current systematic review aims to compare the clinical and radiological outcomes of PCSF and RPSF in traumatic SPD and analyze the biomechanical effectiveness of PCSF. Material and Methods: The Medline, Scopus, and Cochrane databases were searched until February 2023. The primary outcomes were the incidence of implant failure and revision surgery and the amount of displacement of symphysis pubis. Secondary outcomes were the intraoperative blood loss, the scar length, the operative time, the wound infection, and the patients’ functional improvement. Results: Six clinical trial studies with a total of 184 patients and nine biomechanical studies were included. There was no significant difference between the two groups regarding the incidence of implant failure, the prevalence of revision surgery, and the amount of postoperative loss of reduction (p > 0.05 for all outcomes). The intraoperative blood loss (14.9 ± 4.2 mL for PCSF versus 162.7 ± 47.6 mL for PCSF, p < 0.001) and the incision length (1.7 ± 0.9 mL for PCSF versus 8 ± 1.4 mL for PCSF, p < 0.001) were significantly lower after PCSF. The mean operative time was 37 ± 19.1 min for PCSF and 68.9 ± 13.6 min for RPSF (p < 0.001). The infection rate was less frequent in the PCSF group (3% for PCSF versus 14.3% for RPSF, p = 0.01). One clinical trial reported better functional recovery after PCSF. In all biomechanical studies, the threshold for implant failure was beyond the applied forces corresponding to daily activities. Conclusions: PCSF for traumatic SPD is associated with less operative time, less blood loss, and a lower infection rate when compared to conventional plate techniques without increasing the incidence of postoperative fixation failure and revision surgery. Moreover, PCSF has been proven to be biomechanically sufficient for stabilization. Therefore, it should be considered an efficient and viable alternative for the reconstruction of SPD when closed reduction can be adequately achieved. Full article

Background and purpose: Cannulated screws are standard implants for percutaneous fixa-tion of posterior pelvis ring injuries. The choice of whether to use these screws in combination with a washer is still undecided. The aim of this study was to evaluate the biomechanical competence of S1-S2 sacroiliac (SI) screw fixation with and without using a washer across three different screw designs. Material and Methods: Twenty-four composite pelvises were used and an SI joint injury type APC III according to the Young and Burgess classification was simulated. Fixation of the posterior pelvis ring was performed using either partially threaded short screws, fully threaded short screws, or fully threaded long transsacral screws. Biomechanical testing was performed under progressively increasing cyclic loading until failure, with monitoring of the intersegmental and bone-implant movements via motion tracking. Results: The number of cycles to failure and the corresponding load at failure (N) were significantly higher for the fully threaded short screws with a washer (3972 ± 600/398.6 ± 30.0) versus its counterpart without a washer (2993 ± 527/349.7 ± 26.4), p = 0.026. In contrast, these two parameters did not reveal any significant differences when comparing fixations with and without a washer using either partially threaded short of fully threaded long transsacral screws, p ≥ 0.359. Conclusions: From a biomechanical perspective, a washer could be optional when using partially threaded short or fully threaded long transsacral S1-S2 screws for treatment of posterior pelvis ring injuries in young trauma patients. Yet, the omission of the washer in fully threaded short screws could lead to a significant diminished biomechanical stability. Full article

Background and Objectives: Minimally invasive surgeries for acetabulum fracture fixation are gaining popularity due to their known advantages versus open reduction and internal fixation. Antegrade or retrograde screw fixation along the long axis of the posterior column of the acetabulum is increasingly applied in surgical practice. While there is sufficient justification in the literature for the application of the anterior approach, there is a deficit of reports related to the posterior approach. The aim of this study was to evaluate the biomechanical competence of posterior column acetabulum fracture fixation through antegrade screw placement using either a standard cannulated screw or a cannulated compression headless screw (CCHS) via posterior approach. Materials and Methods: Eight composite pelvises were used, and a posterior column acetabulum fracture according to the Letournel Classification was simulated on both their left and right sides via an osteotomy. The sixteen hemi-pelvic specimens were assigned to two groups (n = 8) for either posterior column standard screw (group PCSS) or posterior column CCHS (group PCCH) fixation. Biomechanical testing was performed by applying steadily increased cyclic load until failure. Interfragmentary movements were investigated by means of motion tracking. Results: Initial stiffness demonstrated significantly higher values in PCCH (163.1 ± 14.9 N/mm) versus PCSS (133.1 ± 27.5 N/mm), p = 0.024. Similarly, cycles and load at failure were significantly higher in PCCH (7176.7 ± 2057.0 and 917.7 ± 205.7 N) versus PCSS (3661.8 ± 1664.5 and 566.2 ± 166.5 N), p = 0.002. Conclusion: From a biomechanical perspective, CCHS fixation demonstrates superior stability and could be a valuable alternative option to the standard cannulated screw fixation of posterior column acetabulum fractures, thus increasing the confidence in postoperative full weight bearing for both the patient and treating surgeon. Whether uneventful immediate postoperative full weight bearing can be achieved with CCHS fixation should primarily be investigated in further human cadaveric studies with a larger sample size. Full article