Search Results (59)

With increasing electrification and the connection of more renewable resources at the transmission level, bulk interconnected electric grids need to plan network expansion with new transmission facilities. The transmission expansion planning (TEP) problem is particularly challenging because of the combinatorial, integer optimization nature of the problem and the complexity of engineering analysis for any one possible solution. Network synthesis methods, that is, heuristic-based techniques for building synthetic electric grid models based on complex network properties, have been developed in recent years and have the capability of balancing multiple aspects of power system design while efficiently considering large numbers of candidate lines to add. This paper presents a methodology toward scalability in addressing the large-scale TEP problem by applying network synthesis methods. The algorithm works using a novel heuristic method, inspired by simulated annealing, which alternates probabilistic removal and targeted addition, balancing the fixed cost of transmission investment with objectives of resilience via power flow contingency robustness. The methodology is demonstrated in a test case that expands a 2000-bus interconnected synthetic test case on the footprint of Texas with new transmission to support 2025-level load and generation. Full article

A diode-based rectifier (DR) is an attractive transmission technology for offshore wind farms, which reduces the volume of large bulk platforms. A novel parallel–series DC wind farm based on a distributed DR is proposed, which meets the requirements of high voltage and high power with an isolation capability from other units. The coupling mechanism between a modular multilevel converter (MMC) and a DR has been built, and the coordinate control strategy for the whole system has been proposed based on the MMC triple control targets with intermediate variables. Under the proposed control strategy, the system automatically operates at maximum power point tracking (MPPT). The feasibility of topology and the effectiveness of the control strategy are verified under start-up, power fluctuation, onshore alternating current (AC) fault, and direct current (DC) fault based on the power systems computer-aided design (PSCAD)/electromagnetic transients including direct current (EMTDC) simulation. Full article

Grid-forming inverters (GFMIs) have been identified as critical assets in ensuring modern power system reliability. Their ability to synthesize an internal voltage reference while emulating synthetic inertia has sparked extensive research. These characteristics have recently piqued interest in their capacity to provide blackstart ancillary services. The blackstart of a bulk power system poses significant challenges, namely the large transients from the energization of unloaded transformers, rotational motor loads, and long transmission cables, which have been effectively studied using conventional synchronous generators (SGs). The concept of an inverter-based resource (IBR)-based blackstart continues to be an open research area necessitating further investigations due to the known limitations of IBRs such as low short-circuit current capabilities. This paper presents a blackstart case study of a bulk power system investigating the performances of a conventional SG to a GFMI when utilizing hard switching methods. The paper qualitatively investigates the transient inrush currents from the transformer and rotational load energization sequences. Additional examinations into the significance of the GFMI’s current-limiting schemes and voltage control loop compensator gains are presented. Furthermore, the harmonic distortions from the transformer energization sequence are also evaluated. Finally, a full network energization case is presented to demonstrate how both sources can provide blackstart provisioning services. The models are developed in EMTDC/PSCAD using real-world transmission planning data. Full article

The use of biomass as a source of energy has been identified to be energy intensive, involving high handling costs. However, pelletization reduces the bulk density of biomass, thereby reducing the handling costs and enhancing ease of use. This study modified and evaluated an existing hand-operated fish feed pelleting machine. The parts of the machine that were redesigned were the hopper and the power transmission unit. Corncob was used to evaluate the modified machine using the die hole diameter (5, 6 and 7 mm) and the binder quantity (0, 2.5 and 5 wt%) as factors. The average results obtained for machine efficiency, throughput, pellet length and bulk density were 58.83%, 4.24 kg/h, 15.51 mm and 0.160 g/cm³, respectively. The die hole diameter had a significant effect on the pellet length only. The binder quantity had a significant effect on machine efficiency, throughput and pellet length. Machine efficiency and throughput decreased as the quantity of binder increased, and the pellet length increased with the increasing quantity of binder. Full article

The problem of power grid capacity expansion focuses on adding or modernizing generation and transmission resources to respond to the rise in demand over a long-term planning period. Traditionally, the problem has been mainly viewed from technical and financial perspectives. However, with the rise in the frequency and severity of natural disasters and their dire impacts on society, it is paramount to consider the problem from a nexus of resilience, sustainability, and equity. This paper presents a novel multi-objective optimization framework to perform power grid capacity planning, while balancing the cost of operation and expansion with the life cycle impacts of various technologies. Further, to ensure equity in grid resilience, a social vulnerability metric is used to weigh the energy not served based on the capabilities (or lack thereof) of communities affected by long-duration power outages. A case study is developed for part of the bulk power system in the state of Colorado. The findings of the study show that, by considering life cycle impacts alongside cost, grid expansion solutions move towards greener alternatives because the benefits of decommissioning fossil-fuel-based generation outweigh the costs associated with deploying new generation resources. Furthermore, an equity-based approach ensures that socially vulnerable populations are less impacted by disaster-induced, long-duration power outages. Full article

The basis of the present study is a straightforward method involving fewer chemical species for conjugating gold nanoparticles (AuNPs) with the antimicrobial peptide LL-37 designated as LL-37@AuNPs. Investigating the microstructure characteristics of the resulting materials and their potential as antibacterial and wound-healing substances are the main objectives of this study. Zeta (ζ) potential, Fourier transform infrared (FTIR), X-ray diffraction (XRD), field effect scanning electron microscopy (FE-SEM), energy dispersive X-ray diffraction (EDS), transmission electron microscopy (TEM), and UV-Vis spectrophotometry were used to analyze the physico–chemical properties of LL-37@AuNPs. The magnitude of LL-37′s zeta potential and the LL-37@AuNPs show that the specimens are electrically stable and resistant to flocculation and coagulation. The surface plasmon resonance (RPS) of AuNPs, which is positioned at a wavelength of about 531 nm, was found to be unaffected by the presence of the LL-37 antimicrobial peptide. The FTIR data show the functional group characteristics of the LL-37@AuNPs vibration bands, and the XRD diffractogram confirms the formation of the LL-37@AuNPs conjugate nanocomposite. Based on FE-SEM and TEM data, the bulk of AuNPs were found to have a circular shape, with an average size of about 22.88 ± 8.21 nm. It was discovered that the LL-37@AuNPs had a good ability to inhibit S. aureus from growing. The wound-healing percentage reached 85% on day 12 of the trial, significantly greater than the results of the negative controls. LL-37@AuNPs(4) is the sample that had the highest percentage of wound healing between days 3 and 12. Moreover, sample LL-37@AuNPs(4) contains 0.45 µL of LL-37, whereas sample LL-37@AuNPs(2) contains 0.22 µL of LL-37. The faster wound-healing rate in LL-37@AuNPs(4) was believed to be due to a higher concentration of LL-37, which was able to stop S. aureus from developing while suppressing the inflammation surrounding the wound. The study’s findings reveal that LL-37@AuNPs might be made using a straightforward process, making them a powerful antibacterial and therapeutic substance. However, before this discovery is applied in the field of medicine, a more thorough investigation is necessary. Full article

Renewable energy sources have a multifaceted impact on power grids, ranging from the reliability and quality of electricity to the selective impact on equipment. While renewables used to be distributed in distribution networks, now their capacity is commensurate with thermal power plants and their impact on the grid should not be underestimated. According to the statistics on the interruption of the bulk electric networks, one of the main reasons for emergency shutdowns of extra high-voltage power lines are single-phase short circuits. The problem of mathematical modeling of the limit modes in terms of static stability is very relevant to the design and operation of electric power systems (EPS). Calculations of limit modes have both an independent value and a component of other electrical engineering tasks related to ensuring the required level of reliability and cost-effectiveness of the operation of the united PS. Despite the great degree of development of issues of planning and control of electric modes, system accidents associated with unacceptable loads of network elements occur in the Ukrainian energy industry. Non-phase modes regularly occur in electric power systems, which can lead to an unacceptable load of intersystem network elements, which imposes significant restrictions on their throughput. Single-phase short circuits are more than 95% of other damage that occurs in the line. The use of single-phase auto reclose on the transmission lines allows disconnecting only the damaged phase for a short period of time and not the entire transmission line. This action preserves the transit of electricity along the line and prevents the violation of the stability of parallel operation. To achieve this, the current-free pause of the single-phase auto reclose should last as short as possible. On the other hand, an important task to be solved when using single-phase auto reclose is to choose the minimum duration of the current-free pause necessary for its success. The problem studied in this paper deals with the safety and correct operation of transmission lines (TS) of the Ukrainian bulk power system in special conditions (not predictable, changing due to frequent attacks). For a quickly changing configuration, the power grid uses switches, and in the case of ultra-high voltage, the TS needs to solve the problem of secondary arc currents and recovering stresses in the place of arc burning after its extinction. One of the methods of reducing secondary arc currents and recovering stresses in the place of arc burning after its extinction is the implementation of single-phase automatic reclosing (SPAR). The main theoretical result of the paper is a proposed mathematical model of a compensated power transmission line based on the use of matrix n-poles, which makes it possible to model in detail stationary power transmission modes, including the SPAR mode. The proposed mathematical model of three-phase power transmission has been created using phase coordinates and can be used for the analysis of complex asymmetric modes. The main practical result of the paper is physically interpreted simplified models of three-phase TS, which can be used for the study of resonant overvoltages and currents of the feeding arc in non-full-phase circuit SPAR. The conclusion that can be drawn from the obtained results points out which line lengths must take into account the influence of longitudinal asymmetry when choosing the inductive resistance, i.e., take into account the dependence of the mode parameters on the location of the damaged phase. The observed results show that the largest values of the multiplicity of overvoltages will take place in phase B. The novelty of the work is the developed technique that makes it possible to determine in advance, depending on the disconnected phase of the line, the values of the primary conductivities of the STC (static thyristor compensators) and the corresponding angles of control of the thyristor switches, which satisfy almost complete compensation of the secondary arc at any point of the line in the specific condition (hard) of the bulk power system operation. Full article

Given its adaptable and efficient energy consuming devices during peak hours, the residential building sector is urged to take part in demand response (DR) initiatives with the use of a building energy management system (BMS). The residents of buildings with BMS enjoy secure, pleasant, and fully managed lifestyles. Although the BMS helps the building consume less energy and encourages occupant engagement in energy-saving initiatives, unwelcome interruptions and harsh instructions from the system are inconvenient for the inhabitants, which further discourages their participation in DR initiatives. Building automation control is a crucial factor for improving buildings’ energy efficiency and management, as well as improving the electricity grid’s reliability indices. Smart houses that use the right sizing procedure and energy-management techniques can help lower the demand on the entire grid and potentially sell clean energy to the utility. Recently, smart houses have been presented as an alternative to traditional power-system issues including thermal plant emissions and the risk of blackouts brought on by malfunctioning bulk plants or transmission lines. This paper describes the necessary technology requirements and presents the methodology and the decentralized building automation novel algorithm for efficient demand side management in a building management system. Human comfort aspects including thermal comfort and visual comfort were taken into consideration when selecting heating and lighting controls. The suggested BMS relies primarily on a load-shifting technique, which moves controllable loads to low-cost periods to avoid high loading during peak hours. The model aims to minimize the individual household electricity consumption cost while considering customers’ comfort and lifestyle. All these are applied in an experimental university microgrid, and the results are presented in terms of energy saving in kWh, money in €, and working hours. The results demonstrated that the proposed approach might successfully lower energy use during the DR period and enhance occupant comfort. Full article

The endurance of medium- and high-voltage electrical insulation is a key reliability element in a broad spectrum of applications that cover transmission and distribution levels, the transportation segment, the industrial environment, and power electronics-based energy-conversion systems. The high electric-field stress and high-frequency switching phenomena as well as the impact of environmental conditions lead to the occurrence of partial discharges (PD) and the subsequent deterioration of electrical insulation. Partial discharges usually occur inside solid insulation materials in tiny voids that may either be located adjacent to the electrodes or in the bulk of dielectric material. This effect refers to both AC and DC systems; however, AC voltage is usually much more intensive as compared to DC voltage. This paper describes a novel combined approach based on surface-resistance and potential mapping to reveal the effects of internal processes and the deterioration of insulating material due to the actions of partial discharges. To realize the research objective, the following two-step approach was proposed. Multi-point resistance mapping enables us to identify the spots of discharge channels, manifesting a-few-orders-of-magnitude-lower surface resistance as compared to untreated areas. In addition, surface-potential mapping that was stimulated by corona-charge deposition reflects quasi-equipotential clusters and the related polarity-dependent dynamics of charge decay. A high spatial and temporal resolution allows for the precise mapping and tracing of decay patterns. Experiments were carried out on polyethylene (PE) and Nomex specimens that contained embedded voids. During PD events, the effective discharge areas are identified along with the memory effects that originate from the accumulation of surface charges. Long-term aging processes may drive the formation of channels that are initiated from the deteriorated micro clusters, in turn, penetrating the bulk isolation. The presented methodology and experimental results extend the insight into PD mechanisms and internal surface processes. Full article

Hafnium oxide films were deposited on sapphire and silicon (100) substrates using the DC reactive magnetron sputtering technique from a pure hafnium target at different discharge power levels. The influence of the cathode power on the chemical composition, morphology, crystallographic structure and optical properties of the films was investigated. X-ray diffraction (XRD), energy dispersive X-ray analysis (EDX) and Fourier-transform infrared spectroscopy (FTIR) were employed to determine the chemical composition and bonding structure. In all cases, the films were found to be amorphous or nanocrystalline with increased crystalline content as the sputtering power was increased, according to XRD and FTIR. In addition, EDX showed that the films were oxygen-rich. The effect of power deposition on the surface topography and morphology of the films was studied using atomic force microscopy (AFM) and scanning electron microscopy (SEM). The AFM and SEM images revealed the emergence of mound morphologies as the cathode power was increased. These features are related to blistering effects probably due to the presence of stress and its promotion within the film thickness. Finally, the optical properties showed an average transmission of 80% in the visible range, and the refractive index determined by spectral ellipsometry (SE) was found to be in the range of 1.85–1.92, close to the reported bulk value. SE was also used to study the film porosity observed by SEM, which can be related to the oxygen-rich character of the films. Full article

Two-dimensional (2D) materials own unique band structures and excellent optoelectronic properties and have attracted wide attention in photonics. Tin disulfide (SnS₂), a member of group IV-VI transition metal dichalcogenides (TMDs), possesses good environmental optimization, oxidation resistance, and thermal stability, making it more competitive in application. By using the intensity-dependent transmission experiment, the saturable absorption properties of the SnS₂ nanosheet nearly at 3 μm waveband were characterized by a high modulation depth of 32.26%. Therefore, a few-layer SnS₂ was used as a saturable absorber (SA) for a bulk Er:SrF₂ laser to research its optical properties. When the average output power was 140 mW, the passively Q-switched laser achieved the shortest pulse width at 480 ns, the optimal single pulse energy at 3.78 µJ, and the highest peak power at 7.88 W. The results of the passively Q-switched laser revealed that few-layer SnS₂ had an admirable non-linear optical response at near 3 μm mid-infrared solid-state laser. Full article

Here we report the synthesis and investigation of bulk and nano-sized La_0.7Ba_0.3−xCa_xMnO₃ (x = 0, 0.15, 0.2 and 0.25) compounds that are promising candidates for magnetic refrigeration applications. We compare the structural and magnetic properties of bulk and nano-scale polycrystalline La_0.7Ba_0.3−xCa_xMnO₃ for potential use in magnetic cooling systems. Solid-state reactions were implemented for bulk materials, while the sol–gel method was used for nano-sized particles. Structurally and morphologically, the samples were investigated by X-ray diffraction (XRD), optical microscopy and transmission electron microscopy (TEM). Oxygen stoichiometry was investigated by iodometry. Bulk compounds exhibit oxygen deficiency, while nano-sized particles show excess oxygen. Critical magnetic behavior was revealed for all samples using the modified Arrott plot (MAP) method and confirmed by the Kouvel–Fisher (KF) method. The bulk polycrystalline compound behavior was better described by the tricritical field model, while the nanocrystalline samples were governed by the mean-field model. Resistivity in bulk material showed a peak at a temperature T_p1 attributed to grain boundary conditions and at T_p2 associated with a Curie temperature of T_c. Parent polycrystalline sample La_0.7Ba_0.3MnO₃ has T_c at 340 K. Substitution of x = 0.15 of Ca brings T_c to 308 K, and x = 0.2 brings it to 279 K. Nanocrystalline samples exhibit a very wide effective temperature range in the magnetocaloric effect, up to 100 K. Bulk compounds exhibit a high and sharp peak in magnetic entropy change, up to 7 J/kgK at 4 T at T_c for x = 0.25. To compare the magnetocaloric performances of the studied compounds, both relative cooling power (RCP) and temperature-averaged entropy change (TEC) figures of merit were used. RCP is comparable for bulk polycrystalline and nano-sized samples of the same substitution level, while TEC shows a large difference between the two systems. The combination of bulk and nanocrystalline materials can contribute to the effectiveness and improvement of magnetocaloric materials. Full article

This paper deals with the simulation and the experimental confirmation of electromagnetic events that could interfere with the successful formation of the restoration path during the power system restoration procedure. The studied phenomena are more relevant for bulk power systems characterized by a low short circuit power as the restoration backbone. In particular, two case studies have been simulated and analyzed: one related to a transformer energization during the formation of the restoration path, and the other one occurred after the de-energization of some transmission lines and one autotransformer belonging to the restoration path. From the simulation results, it emerged that such events are related to the resonant effects between the supplying transformer and the restored network. Such resonances could have negative effects on the restoration if they are not effectively managed. In order to evaluate the impact of such phenomena in real networks, the measurement recordings of on-field tests were compared with the simulation results. It is worth noting that the performed analyses require the knowledge of several parameters that were not always available in practice. Hence, the exact magnitude of the described resonant phenomena was not easy to foresee for the restoration of real networks. The performed comparison confirms the preliminary simulation results and highlights that detailed electromagnetic models are particularly important to support the power system restoration management, in particular the planning of recovery procedures. Full article

Power flow calculation is the foundation of security analyses in a power system, and the phenomenon of convergence failure is becoming more prominent with the expansion of the power grid. The existing convergence failure diagnosis methods based on optimization modeling and local feature recognition are no longer viable for bulk power systems. This paper proposes a diagnosis method based on intermediate iteration data and the identification of the transmission power congested channel. Firstly, the transmission power congestion index is constructed, and then a method for identifying transmission congestion channels is proposed. The reasons for convergence failure of the power flow are diagnosed from two aspects: excessive power to be transmitted and insufficient transmission capacity. Finally, with the aim of alleviating transmission channel congestion, a correction strategy for power flow injection space data was constructed, which generates relaxation schemes for operational variables. The effectiveness of the proposed strategy was verified using the simulation results of an actual provincial power grid and a standard example power system with 13,659 buses. The method proposed in this paper is entirely based on intermediate power flow iteration data, which avoids the complex modeling of the power flow adjustment and provides methodological support for power flow diagnosis in bulk power systems. Full article

Modern communication networks and digital control techniques are used in a smart grid. The first step is to classify the features of several communication networks and conduct a comparative investigation of the communication networks applicable to the smart grid. The integration of distributed generation has significantly increased as the global energy demand rises, and sustainable energy for electric vehicles and renewable energies worldwide are being pursued. Additional explanations for this surge include environmental concerns, the reforming of the power sector, and the advancing of small-scale electricity generation technologies. Smart monitoring and control of interconnected systems are required to successfully integrate distributed generation into an existing conventional power system. Electric-vehicles-based smart grid technologies are capable of playing this part. Smart grids are crucial to avoid becoming locked in an obsolete energy infrastructure and to draw in new investment sources and build an effective and adaptable grid system. To achieve reliability and high-quality power systems, it is also necessary to apply intelligent grid technologies at the bulk power generation and transmission levels. This paper presents smart grid applicable communication networks and electric vehicles empowering distributed generation systems. Additionally, we address some constraints and challenges and make recommendations that will give proper guidelines for academicians and researchers to resolve the current issues. Full article