Search Results (11)

Polymeric biocomposites are emerging as a new generation of eco-friendly and cost-effective materials that provide sustainable alternatives for the polymer industry while supporting environmental conservation. This study investigates the mechanical behavior of Low-Density Polyethylene (LDPE) compounds blended with natural rubber (NR) and reinforced with silanized Sugarcane Bagasse Ash (SCBA), chemically modified with bis(3 triethoxysilylpropyl) tetrasulfide (TESPT). Blends were formulated in LDPE/NR-SCBA weight ratios (wt%) of 90/10, 70/30, and 50/50, and processed at mixing speeds of 40 and 80 rpm to evaluate their potential as thermoplastic additives. Mechanical testing showed that blends mixed at 80 rpm achieved an 86% increase in elongation, while those processed at 40 rpm demonstrated a 78% enhancement in tensile strength. The incorporation of NR and vulcanizing systems markedly improved the overall mechanical properties of the composites. These biocomposites present promise for applications in the footwear industry (especially for soles) and for ergonomic molded components by conferring the advantageous combination of mechanical performance and esthetic appeal. Furthermore, development supports innovative manufacturing processes and contributes to reducing the industry`s carbon footprints, mitigating its negative impact on the planet. Full article

In order to enhance the anti-corrosion property of epoxy coatings on 7N01 aluminum alloy, cerium nitrate and zeolite particles were incorporated into a bis-(triethoxysilylpropyl)tetrasulfide (BTESPT) silane solution to pretreat the substrate. Scanning electron microscopy (SEM) and an electronic probe microanalyzer (EPMA) were used to characterize the morphology and chemical composition of the composite silane film. The corrosion performances of the epoxy coatings were evaluated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) and based on the morphology and chemical composition of the interfacial region after salt spray tests. The thickness of the composite silane film at 5% BTESPT doped with 5 × 10⁻³ M cerium nitrate and 0.5 g/L zeolite particles was about 2.1 μm. The composite silane film can provide active protection to the substrate surface beneath the epoxy coating. It promotes the impedance value of the coating at 10⁻² Hz by two to three orders of magnitude and greatly lessens the interfacial region corrosion between the coating and the substrate. This effect can be ascribed to the strong barrier effect of the composite silane film and cerium ions released from the silane network and the zeolite particles. Full article

Elastomer composites for dynamic mechanical applications with a low dissipation of energy are of great importance in view of their application in tire compounds. In this work, furnace carbon black functionalized with 2-2,5-dimethyl-1H-pyrrol-1-yl-1,3-propanediol (SP) was used in place of silica in an elastomer composite based on poly(styrene-co-butadiene) from solution anionic polymerization and poly(1,4-cis-isoprene) from Hevea Brasiliensis. The traditional coupling agent used for silica was also used for the CB/SP adduct: 3,3′-bis(triethoxysilylpropyl)tetrasulfide (TESPT). The composite with the CB/SP + TESPT system revealed a lower Payne effect, higher dynamic rigidity, and lower hysteresis, compared to the composite with CB + TESPT, although the latter composite had a higher crosslinking density. The properties of the silica and the CB/SP + TESPT-based composites appear similar, though in the presence of slightly higher hysteresis and lower ultimate properties for the CB/SP-based composite. The use of CB in place of silica allows us to prepare lighter compounds and paves the way for the preparation of tire compounds with lower environmental impacts. Full article

Using vegetable oils as a plasticizer or processing aid in green rubber products is becoming popular due to environmental concerns. However, differences in vegetable oil processing result in varying amounts of low-molecular-weight (low-MW) free fatty acids (FFAs) in their composition, which range from 2% to 30%. This research investigated how the properties of silica-filled styrene butadiene rubber (SBR) and butadiene rubber (BR) blends were affected by the presence of FFAs in palm oil (PO). The rubber compounds containing a 70/30 SBR/BR blend, 30 phr of silica, and 2 phr of bis-(3-triethoxysilylpropyl) tetrasulfide (TESPT), and the vulcanizing agents were prepared and tested. The PO content was kept constant at 20 phr, while the number of FFAs, i.e., lauric acid (LA), palmitic acid (PA), and oleic acid (OA), in PO varied from 10–30%. The viscosity, dynamic mechanical properties, morphology, cure characteristics, and mechanical properties of the rubber blend were then measured. Regardless of the FFA types, increasing FFA content in PO decreased scorch time, cure time, minimum torque, and viscosity. As the FFA content increased, the torque difference and crosslink density also increased, which led to higher hardness, modulus, tensile strength, and abrasion resistance. The FFA types had a slight effect on the vulcanizate properties, even though LA showed slightly better mechanical properties than PA and OA. The results reveal that FFAs in PO not only improve processability but also function as a co-activator in silica-filled sulfur-vulcanized SBR/BR blend compounds. Full article

The aim of this work was application of ground eggshells in various amounts by weight as a biofiller for natural rubber (NR) biocomposites. Cetyltrimethylammonium bromide (CTAB), ionic liquids (ILs), i.e., 1-butyl-3-methylimidazolium chloride (BmiCl) and 1-decyl-3-methylimidazolium bromide (DmiBr), and silanes, i.e., (3-aminopropyl)-triethoxysilane (APTES) and bis [3-(triethoxysilyl)propyl] tetrasulfide (TESPTS), were used to increase the activity of ground eggshells in the elastomer matrix and to ameliorate the cure characteristics and properties of NR biocomposites. The influence of ground eggshells, CTAB, ILs, and silanes on the crosslink density, mechanical properties, and thermal stability of NR vulcanizates and their resistance to prolonged thermo-oxidation were explored. The amount of eggshells affected the curing characteristics and crosslink density of the rubber composites and therefore their tensile properties. Vulcanizates filled with eggshells demonstrated higher crosslink density than the unfilled sample by approximately 30%, whereas CTAB and ILs increased the crosslink density by 40–60% compared to the benchmark. Owing to the enhanced crosslink density and uniform dispersion of ground eggshells, vulcanizates containing CTAB and ILs exhibited tensile strength improved by approximately 20% compared to those without these additives. Moreover, the hardness of these vulcanizates was increased by 35–42%. Application of both the biofiller and the tested additives did not significantly affect the thermal stability of cured NR compared to the unfilled benchmark. Most importantly, the eggshell-filled vulcanizates showed improved resistance to thermo-oxidative aging compared to the unfilled NR. Full article

This work aims to enhance the mechanical properties, oil resistance, and thermal properties of acrylonitrile butadiene rubber (NBR) by using the Nile tilapia fish scales as a filler and using bis(triethoxysilylpropyl)tetrasulfide (TESPT) as a coupling agent (CA). The prepared fish scale particles (FSp) are B-type hydroxyapatite and the particle shape is rod-like. The filled NBR with FSp at 10 phr increased tensile strength up to 180% (4.56 ± 0.48 MPa), reduced oil absorption up to 155%, and increased the decomposition temperature up to 4 °C, relative to the unfilled NBR. The addition of CA into filled NBR with FSp at 10 phr increased tensile strength up to 123% (5.62 ± 0.42 MPa) and percentage of elongation at break up to 122% relative to the filled NBR with FSp at 10 phr. This work demonstrated that the prepared FSp from the Nile tilapia fish scales can be used as a reinforcement filler to enhance the NBR properties for use in many high-performance applications. Full article

In order to prepare engineering tires with lower rolling resistance and better wet slip resistance in a more environmentally friendly way. In this study, a series of low volatile organic compound (VOC) M_x–Si69 coupling agents (x = 1, 2, 3, 4, 5, 6, which means the number of ethoxy group in bis-(γ-triethoxysilylpropyl)-tetrasulfide (Si69) substituted by the aliphatic polyether chain) were applied to silica/NR nanocomposites to prepare tire tread with excellent performance. Firstly, M₁–Si69 was substantiated as the best choice of M_x–Si69 and Si69 to achieve comprehensive optima in the mechanical properties of silica/NR nanocomposites characterized by dynamic and static mechanical properties. Afterwards, the modification of silica with M₁–Si69 induced by Non-Rubber Contents (NRCs) in silica/NR nanocomposites was revealed by comparing the filler network, micromorphology, and mechanical properties of isoprene rubber (IR) and NR nanocomposites. Furthermore, compared with Si69, the M₁–Si69 coupling agent was found to conspicuously reduce the energy loss and improve the safety performance of engineering tires according to evaluations of the rolling resistance and dynamic thermomechanical properties of the silica/NR nanocomposites. Finally, the critical function of M₁–Si69 in reducing ethanol (a kind of volatile organic compound (VOC)) emissions from the reaction of coupling agent and silica was disclosed by gas chromatography–mass spectrometry. Full article

Flexible self-healing composite was fabricated based on blending the bromobutyl rubber (BIIR) and epoxide natural rubber (ENR) filled with hybrid fillers of carbon nanotubes (CNT) and carbon black (CB). To achieve self-recoverability, modification of BIIR was carried out through butyl imidazole (IM), and the healing capability was then activated by the addition of bis(triethoxysilylpropyl)tetrasulfide (TESPT), which resulted in good dispersion of CNT/CB in BIIR/ENR blends. The silanization of TESPT and CNT/CB hybrid filler surfaces was confirmed by attenuated total reflection-Fourier transform infrared (ATR-FTIR) spectroscopy. Adding CNT/CB and incorporating TESPT into the composites effectively improved the curing and mechanical properties of the blends in terms of estimated crosslink density and tensile modulus. Further, the self-healing propagation rate was enhanced by the thermal conductivity of fillers and the ion–dipole intermolecular forces between the rubber chains, leading to the highest abrasion resistance and electrical conductivity. Using an environmentally friendly process, the recyclability of the self-healing composites was improved by the re-compression of the samples. With this, the constant conductivity relating to the rearrangement of the CNT/CB network is examined related to the usability of the composites at 0 and 60 °C. The conductive composites filled with a TESPT silane coupling agent present an opportunity for vehicle tires and other self-repairing applications. Full article

The multi-stimuli responsive drug delivery system has recently attracted attention in cancer treatments, since it can reduce several side effects and enhance cancer therapeutic efficacy. Herein, we present the intracellular antioxidant (glutathione, GSH), enzyme (hyaluronidase, HAase), and hydrogen peroxide (H₂O₂) triggered mesoporous organo-silica (MOS) nanocomposites for multi-modal treatments via chemo-, photothermal, and photodynamic cancer therapies. A MOS nanoparticle was synthesized by two-types of precursors, tetraethyl orthosilicate (TEOS) and bis[3-(triethoxysilyl)propyl] tetrasulfide (BTES), providing large-sized mesopores and disulfide bonds cleavable by GSH. Additionally, we introduced a new β-cyclodextrin-hyaluronic acid (CDHA) gatekeeper system, enabling nanocomposites to form the specific interaction with the ferrocene (Fc) molecule, control the drug release by the HAase and H₂O₂ environment, as well as provide the targeting ability against the CD44-overexpressing melanoma (B16F10) cells. Indocyanine green (ICG) and doxorubicin (Dox) were loaded in the MOS-Fc-CDHA (ID@MOS-Fc-CDHA) nanocomposites, allowing for hyperthermia and cytotoxic reactive oxygen species (ROS) under an 808 nm NIR laser irradiation. Therefore, we demonstrated that the ID@MOS-Fc-CDHA nanocomposites were internalized to the B16F10 cells via the CD44 receptor-mediated endocytosis, showing the controlled drug release by GSH, HAase, and H₂O₂ to enhance the cancer therapeutic efficacy via the synergistic chemo-, photothermal, and photodynamic therapy effect. Full article

The viscoelastic behavior and reinforcement mechanism of polyethylene glycol (PEG) as an interfacial modifier in green tire tread composites were investigated in this study. The results show a clear positive effect on overall performance, and it significantly improved all the parameters of the “magic triangle” properties, the abrasion resistance, wet grip and ice traction, as well as the tire rolling resistance, simultaneously. For the preparation of the compounds, two mixing steps were used, as PEG 4000 was added on the second stage in order to avoid the competing reaction between silica/PEG and silanization. Fourier transform infrared spectroscopy (FTIR) confirmed that PEG could cover the silanol groups on the silica surface, resulting in the shortening of cure times and facilitating an increase of productivity. At low content of PEG, the strength was enhanced by the improvement of silica dispersion and the slippage of PEG chains, which are chemically and physically adsorbed on silica surface, but the use of excess PEG uncombined with silica in the compound, i.e., 5 phr, increases the possibility to shield the disulfide bonds of bis(3-(triethoxysilyl)-propyl) tetrasulfide (TESPT), and, thus, the properties were deteriorated. A constrained polymer model was proposed to explain the constrained chains of PEG in the silica-loaded composites on the basis of these results. An optimum PEG content is necessary for moderately strong matrix–filler interaction and, hence, for the enhancement in the mechanical properties. Full article

Tires are an important vehicle component, as car handling, safety and fuel economy depend for a major part on the tire composition and construction. As a consequence, tires are improved continuously. The most prominent improvement in the recent past was the use of a silica-silane filler system in passenger car tread compounds, instead of traditionally used carbon black. For recycling and re-use of end-of-life car tire rubber one of the most promising recycling methods is devulcanization: re-plasticizing the vulcanized rubber by selectively breaking the sulfur bridges between the polymer molecules. In the present paper, the influence of silica, which is present in the passenger car tires granulate, on both devulcanization and subsequent revulcanization, is investigated. In a step-wise approach it is shown that the presence of silica influences both devulcanization and revulcanization. The best tensile strength of the revulcanizate, using a carbon-black-based revulcanization formulation, was 5 MPa. This could be improved to 6.5 MPa by using 2.8 phr of 1,3-DiPhenylGuanidine (DPG) in the revulcanization formulation. After addition of a silanization step during revulcanization by adding 3.2 phr bis[3-(TriEthoxySilyl)Propyl] Tetrasulfide (TESPT), a silane, to the formulation, the tensile strength of the revulcanizate was further improved to 8 MPa. With these results it is shown that the silica in the granulate can be used to improve the revulcanization properties. To check the benefits of using pure tire tread material for the devulcanization and subsequent revulcanization, of both a carbon black and a silica-based virgin tread compound, it is shown that a tensile strength of the revulcanizate of 13 MPa can be reached. This shows the potential of devulcanized rubber when the various tire components are separated before whole car tire material is granulated as the beginning of the recycling. Full article