Search Results (27)

To enhance the photocatalytic performance of ZnO, the ZnO/g-C₃N₄ (ZCN) composite was prepared by ZnO and g-C₃N₄ under ball milling, and then the ternary graphene oxide (GO)/ZnO/g-C₃N₄ (GZCN) composite was achieved by using sonicating, stirring, and liquid phase evaporating. The photocatalytic performance was tested under UV light and natural solar light, respectively. The experimental results displayed that the GZCN composite revealed excellent photocatalytic performance under UV light and natural sunlight. When the ratio of ZnO to g-C₃N₄ is 1:0.2 and the mass fraction of graphene oxide is 0.25% in GZCN composite, the modified ZnO possesses optimal photocatalytic activity under UV light or natural solar light. RhB dye is degraded by 94% within 20 min under UV light, which is 3.41 times that of pure ZnO. Moreover, GZCN can degrade 88% of RhB in 60 min under natural sunlight. The enhancement for photocatalytic activity is attributed to the excellent conductivity of GO and heterojunction interaction between ZnO and g-C₃N₄, where the special electronic structure of g-C₃N₄ expands the spectral response range of ZnO and accelerates the transmission of photogenerated electrons and holes. Full article

As a well-known photocatalyst, TiO₂ still suffers from rapid electron–hole recombination and limited visible light absorption. To overcome these challenges, the combination of graphene and TiO₂ has been proposed. However, traditional methods such as ball milling and hydrothermal synthesis face limitations, including high energy consumption and complex procedures. Here, we develop a simple and industrially feasible method to prepare reduced graphene oxide (rGO)-coated TiO₂ nanoparticles, referred to as rGO-TiO₂ composites. The optimized rGO-TiO₂ composites exhibit an enhanced photocatalytic degradation of rhodamine B (RhB) under simulated sunlight conditions, about 99.95% for 4% rGO-TiO₂ within 80 min. The first-order reaction rate constant (k) of 4% rGO-TiO₂ (0.0867 min⁻¹) is 5.42 times higher than that of nano TiO₂ (0.0135 min⁻¹). The key reactive species involved in the degradation process are identified. Additionally, the effects of pH and NaCl concentration on the degradation efficiency of rGO-TiO₂ are also investigated. The 4% rGO-TiO₂ composite exhibits an excellent photocatalytic activity within the pH range of 3.87–11.89, and the NaCl concentration does not affect its photocatalytic efficiency. After characterization, the enhanced photocatalytic activity is ascribed to the introduction of rGO and the generation of surface oxygen vacancies (O_V) and Ti³⁺ in TiO₂ crystals. Full article

The microwave absorption performance of high-entropy alloys (HEAs) can be improved by reducing the reflection coefficient of electromagnetic waves and broadening the absorption frequency band. The present work prepared flaky irregular-shaped Al_1.5Co₄Fe₂Cr and Al_1.5Co₄Fe₂Cr@rGO alloy powders by mechanical alloying (MA) at different rotational speeds. It was found that the addition of trace amounts of reduced graphene oxide (rGO) had a favorable effect on the impedance matching, reflection loss (RL), and effective absorbing bandwidth (EAB) of the Al_1.5Co₄Fe₂Cr@rGO HEA composite powders. The EAB of the alloy powders prepared at 300 rpm increased from 2.58 GHz to 4.62 GHz with the additive, and the RL increased by 2.56 dB. The results showed that the presence of rGO modified the complex dielectric constant of HEA powders, thereby enhancing their dielectric loss capability. Additionally, the presence of lamellar rGO intensified the interfacial reflections within the absorber, facilitating the dissipation of electromagnetic waves. The effect of the ball milling speed on the defect concentration of the alloy powders also affected its wave absorption performance. The samples prepared at 350 rpm had the best wave absorption performance, with an RL of −16.23 and −17.28 dB for a thickness of 1.6 mm and EAB of 5.77 GHz and 5.43 GHz, respectively. Full article

Durian shell waste was used to fabricate activated carbon (AC) using a hydrothermal process and three-dimensional (3-D) ball milling. Reduced graphene oxide (rGO) was composited with activated durian shell carbon (DC) to enhance the electrochemical properties for fabricating a supercapacitor (SC) device. Scanning electron microscopic (SEM) examination of the AC from hydrothermally processed durian shell carbon (AC–HDC) and AC–HDC that was 3D ball milled for 15 min (rGO/AC–HDC–3D15M) showed compacted and uniformly distributed particles with good porosity. The rGO/AC–HDC–3D15M sample exhibited high specific surface area (SSA) using the Brunauer–Emmett–Teller (BET) methodology, 2311 m²/g, and an average pore size of 1.88 nm. Electrochemical results showed that the rGO/AC–HDC–3D15M sample had the highest specific capacitance (Cs) of 545.78 F/g, power density (Pd) of 260.834 W/kg and energy density (Ed) of 60.834 Wh/kg. A coin cell SC device using an rGO/AC–HDC3D15M electrode with a 3M KOH electrolyte exhibited a high Cs of 65.585 F/g with a high energy density of 5.123 W h/kg and power density of 47.286 W/kg. Thus, the novelty of this manuscript is that (1) the structure of the rGO/AC–HDC–3D15M composite could promote fast ionic and electronic migration during charging and discharging and (2) a rGO/AC–HDC–3D15M composite, which showed electric double-layer capacitor (EDLC) could produce a positive synergistic effect for efficient electrochemical reactions. Moreover, the high surface area of the rGO/AC–HDC–3D15M composite may mitigate the volume expansion of electrodes during cycling. Thus, this work shows that an rGO/AC–HDC–3D15M composite prepared using a hydrothermal process with 3-D ball milling can show enhanced electrochemical performance for the fabrication of an EDLC supercapacitor device. Full article

Silicon-containing materials are still the most promising alternatives to graphite as the negative electrodes of lithium-ion batteries. However, the different Li⁺ storage mechanism combined with the high capacity result in new requirements for the passive electrode components, such as the binder. To ensure sufficient cycling stability, silicon must be embedded in a suitable carbonaceous matrix. For this purpose, we used a simple ball milling process with reduced graphene oxide (rGO) to produce Si-rGO composites with µm- and nm-sized silicon particles. The rGO was synthesized previously from a two-step thermal synthesis method developed in-house. Subsequently, electrodes with varying CMC/SBR ratios (3:1, 1:1, and 1:3) were prepared from the composites containing the different Si particle sizes. It was found that the optimal binder ratio depends on the size of the Si particles. For the nm-Si-rGO composite, a CMC/SBR ratio of 3:1 results in a total capacity over 51 cycles of 20.6 Ah g⁻¹, which means an improvement of 20% compared to CMC/SBR = 1:3 (17.1 Ah g⁻¹). In contrast, we demonstrate that for µm-Si-rGO composites with an optimal CMC/SBR ratio of 1:1 (13.0 Ah g⁻¹), compared to nm-Si-rGO, a higher SBR content is beneficial for the cycling behavior. Moreover, a comparison with graphite from the literature indicates that a rGO-matrix reduces the need for SBR. Full article

The reduced graphene oxide/iron oxide (rGO/Fe₂O₃) and reduced graphene oxide/cobalt oxide (rGO/Co₃O₄) composite anodes have been successfully prepared through a simple and scalable ball-milling synthesis. The substantial interaction of Fe₂O₃ and Co₃O₄ with the rGO matrix strengthens the electronic conductivity and limits the volume variation during cycling in the rGO/Fe₂O₃ and rGO/Co₃O₄ composites because reduced graphene oxide (rGO) helps the metal oxides (MOs) to attain a more efficient diffusion of Li-ions and leads to high specific capacities. As anode materials for LIBs, the rGO/Fe₂O₃ and rGO/Co₃O₄ composites demonstrate overall superb electrochemical properties, especially rGO/Fe₂O₃T−5 and rGO/Co₃O₄T−5, showcasing higher reversible capacities of 1021 and 773 mAhg⁻¹ after 100 cycles at 100 mAg⁻¹, accompanied by the significant rate performance. Because of their superior electrochemical efficiency, high capacity and low cost, the rGO/Fe₂O₃ and rGO/Co₃O₄ composites made by ball milling could be outstanding anode materials for LIBs. Due to the excellent electrochemical performance, the rGO/Fe₂O₃ and rGO/Co₃O₄ composites prepared via ball milling could be promising anode materials with a high capacity and low cost for LIBs. The findings may provide shed some light on how other metal oxides wrapped by rGO can be prepared for future applications. Full article

Nitrogen-doped carbon nanomaterial (NDCNM) was synthesized by grinding a mixture of graphene oxide and melamine in a planetary mill with both balls and milling chamber of zirconium dioxide. In the electron spin resonance spectrum of NDCNM, a broad signal with g = 2.08 was observed in addition to a narrow signal at g = 2.0034. In the study using a vibrating-sample magnetometer, the synthesized material is presumably a ferromagnet with a coercive force of 100 Oe. The specific magnetization at 10,000 Oe is approximately 0.020 and 0.055 emu/g at room temperature and liquid nitrogen temperature, respectively. Full article

Copper–tungsten (Cu-W) composites are widely used in high-power and -temperature electrical applications. The combination of these metals, however, leads to compromised physical and electrical properties. Herein, we produce Cu-W-graphene oxide (Cu-W-GO) composites to address this challenge. To ensure uniform density composites, the as-received metal powders were flattened into a flake morphology by ball milling and then mixed with up to 0.5 wt.% GO flakes. The green forms were processed using spark plasma sintering. The GO was found to be well-dispersed amongst the metallic phases in the final composite. The addition of GO reduced the relative density of the composites slightly (4.7% decrease in relative density at 0.5 wt% GO loading for the composites processed at 1000 °C). X-ray diffraction confirmed good phase purity and that no carbide phases were produced. GO was found to improve the mechanical properties of the Cu-W, with an optimal loading of 0.1 wt.% GO found for ultimate compression strength and strain to failure, and 0.3 wt.% optimal loading for the 0.2% offset yield strength. Significantly, the electrical conductivity increased by up to 25% with the addition of 0.1 wt.% GO but decreased with higher GO loadings. Full article

Ag/Ni composite contact materials are widely used in low-voltage switches, appliances, instruments, and high-precision contacts due to their good electrical conductivity and processing properties. The addition of small amounts of additives can effectively improve the overall performance of Ag/Ni contact materials. Graphene has good applications in semiconductors, thermal materials, and metal matrix materials due to its good electrical and thermal conductivity and mechanical properties. In this paper, Ag-graphene composites with different added graphene contents were prepared by in situ synthesis of graphene oxide (GO) and AgNO₃ by reduction at room temperature using ascorbic acid as a reducing agent. The Ag-graphene composites and nickel powder were ball-milled and mixed in a mass ratio of 85:15. The Ag-graphene/Ni was tested as an electrical contact material after the pressing, initial firing, repressing, and refiring processes. Its fusion welding force and arc energy were measured. The results show a 12% improvement in electrical conductivity with a graphene doping content of approximately 0.3 wt% compared to undoped contacts, resulting in 33.8 IACS%. The average contact fusion welding force was 49.49 cN, with an average reduction in the fusion welding force of approximately 8.04%. The average arc ignition energy was approximately 176.77 mJ, with an average decrease of 13.06%. The trace addition of graphene can improve the overall performance of Ag/Ni contacts and can promote the application of graphene in electrical contact materials. Full article

To improve the dispersion of graphene oxide particles in wood for better thermal conductivity, this paper proposes the feasibility of obtaining graphene oxide with a smaller particle size using ball milling and its application in melamine resin-modified poplar veneer. The median diameter of multilayer graphene oxide was measured to learn the effects of different ball milling conditions on the particle size of graphene oxide, and the optimum ball milling process was chosen. In addition, the microscopic characterization of graphene oxide under the optimum ball milling process was carried out to investigate the microstructural changes in multilayer graphene after ball milling. Furthermore, the thermal conductivity of the graphene oxide/melamine resin-impregnated mixture modified veneer with the optimum ball milling process was also tested. The results show that, under the optimum ball milling process conditions of SDS wet ball milling with a vibration frequency of 30 Hz for 60 min, the particle size of the multilayer graphene was the smallest, and the median diameter could be reduced to 124 nm. Simultaneously, the thermal conductivity of the melamine resin-modified poplar veneer enhanced by the ball-milled graphene reached 0.405 W·m⁻¹·K⁻¹. In addition, it revealed that the number of graphene oxide layers was reduced to four after ball milling. However, the multilayer graphene was partially oxidized, the lamellar structure was destroyed and the crystallinity was reduced. Full article

Tungsten disulfide nanosheets were successfully prepared by one-step chemical vapor deposition using tungsten oxide and thiourea in an inert gas environment. The size of the obtained nanosheets was subsequently reduced down to below 20 nm in width and 150 nm in length using high-energy ball milling, followed by 0.5 and 1 wt% graphene loading. The corresponding vibrational and structural characterizations are consistent with the fabrication of a pure WS₂ structure for neat sampling and the presence of the graphene characteristic vibration modes in graphene@WS₂ compounds. Additional morphological and crystal structures were examined and confirmed by high-resolution electron microscopy. Subsequently, the investigations of the optical properties evidenced the high optical absorption (98%) and lower band gap (1.75 eV) for the graphene@WS₂ compared to the other samples, with good band-edge alignment to water-splitting reaction. In addition, the photoelectrochemical measurements revealed that the graphene@WS₂ (1 wt%) exhibits an excellent photocurrent density (95 μA/cm² at 1.23 V bias) compared with RHE and higher applied bias potential efficiency under standard simulated solar illumination AM1.5G. Precisely, graphene@WS₂ (1 wt%) exhibits 3.3 times higher performance compared to pristine WS₂ and higher charge transfer ability, as measured by electrical impedance spectroscopy, suggesting its potential use as an efficient photoanode for hydrogen evolution reaction. Full article

Innovative nanostructured materials offer the possibility of enhancing the tribological performance of traditional materials like graphite and molybdenum disulfide (MoS₂). In this study, the scratch resistance of two different copper powders, dendritic and spherical, and their composites with traditional MoS₂, nanometric MoS₂, and graphene nanoplatelets was investigated. Metal powder metallurgy was employed to produce composite materials with 5 wt% and 10 wt% of each solid lubricant. A ball milling step was employed to grind and mix the matrix copper powder with the lubricants. The use of a cold press combined with the sintering in inert atmosphere at 550 °C limited the oxidation of the copper and the degradation of the solid lubricants. The so-produced materials were characterized through a variety of techniques such as micro-indentation hardness, electrical resistivity, contact angle wettability, X-ray diffraction, Raman scattering, and scanning electron microscopy. Moreover, micro-scratch tests were performed on both pure copper and composite materials for comparing the apparent scratch hardness and friction coefficients. The scratches were examined with confocal laser scanning microscopy (CLSM), to identify the evolution of the damage mechanisms during the formation of the groove. The results highlighted the important difference between the dendritic and spherical copper powders and demonstrated a way to improve wear behavior thanks to the use of nanometric powders as solid lubricants. Full article

The transformation of biomass, a carbon resource presenting a huge potential to produce valuable chemicals, requires the search for sustainable catalytic routes. This work proposes the microwave-assisted oxidation of biomass -derived substrates, such as glycerol and the furfural derivatives 5-(hydroxymethyl)furfural (HMF) and 5-hydroxymethyl-2-furancarboxylic acid (HFCA), using the C-scorpionate dichloro-gold(III) complex [AuCl₂(κ²-Tpm)]Cl (Tpm = HCpz₃; pz = pyrazol-1-yl) as a catalyst, as prepared and supported on graphene, in solvent-free conditions. The unprecedented application of a mechanochemical procedure (in a planetary ball mill, in solid state) to synthesize a C-scorpionate complex, the [AuCl₂(κ²-Tpm)]Cl, is disclosed. The immobilization of [AuCl₂(κ²-Tpm)]Cl on graphene was performed using different methods, including some (e.g., microwave irradiation and liquid assisted grinding) for the first time. The structural properties and the performance of the prepared catalytic materials are presented and discussed. Full article

A simple method for the mechanochemical synthesis of an effective metal-free electrocatalyst for the oxygen reduction reaction was demonstrated. A nitrogen-doped carbon material was obtained by grinding a mixture of graphene oxide and melamine in a planetary ball mill. The resulting material was characterized by XPS, EPR, and Raman and IR spectroscopy. The nitrogen concentration on the N-bmGO surface was 5.5 at.%. The nitrogen-enriched graphene material (NbmGO has half-wave potential of −0.175/−0.09 V and was shown to possess high activity as an electrocatalyst for oxygen reduction reaction. The electrocatalytic activity of NbmGO can be associated with a high concentration of active sites for the adsorption of oxygen molecules on its surface. The high current retention (93% for 12 h) after continuous polarization demonstrates the excellent long-term stability of NbmGO. Full article

Magnesium aluminate and other alumina-based spinels attract attention due to their high hardness, high mechanical strength, and low dielectric constant. MgAl₂O₄ was produced by a solid-state reaction between MgO and α-Al₂O₃ powders. Mechanical activation for 30 min in a planetary ball mill was used to increase the reactivity of powders. Yttrium oxide and graphene were added to prevent abnormal grain growth during sintering. Samples were sintered by hot pressing under vacuum at 1450 °C. Phase composition and microstructure of sintered specimens were characterized by X-ray powder diffraction and scanning electron microscopy. Rietveld analysis revealed 100% pure spinel phase in all sintered specimens, and a decrease in crystallite size with the addition of yttria or graphene. Density measurements indicated that the mechanically activated specimen reached 99.6% relative density. Furthermore, the highest solar absorbance and highest spectral selectivity as a function of temperature were detected for the mechanically activated specimen with graphene addition. Mechanical activation is an efficient method to improve densification of MgAl₂O₄ prepared from mixed oxide powders, while additives improve microstructure and optical properties. Full article