Search Results (19)

In this study, the impacts of various grouting methods and volumes on the vertical bearing characteristics of model piles in clay strata were investigated through indoor static load tests on one ungrouted model pile and two model piles with grouting at the pile tip, as well as two model piles with distributed grouting at the pile tip and along the pile side. These tests were performed in conjunction with data obtained from optical fiber sensors that monitored changes in the internal forces of the pile body. The results indicate that, compared to the ungrouted model pile Z1, the ultimate bearing capacities of the grouted model piles Z2 to Z5 were increased by 83.9%, 175.0%, 125.0%, and 253.6%, respectively. Additionally, the displacements at the pile tops after failure reached 57.6%, 62.3%, 69.5%, and 73.5% that of the ungrouted model pile Z1. These results demonstrate that post-grouting can significantly enhance the ultimate bearing capacity of model piles and reduce settlement at the pile top. Under various loads, the axial force of the pile body decreases gradually with the increasing depth of the pile foundation and increases with the increasing load at the pile top. The increase in the ultimate average side friction resistance and ultimate tip resistance of the grouted model piles (i.e., Z2 to Z5), in comparison to the ungrouted pile, was positively correlated with the grouting volume at the pile tip and along the pile side. All five model piles displayed the characteristics of friction piles. Full article

Myopic eye growth induces mechanical stretch, which can lead to structural and functional retinal alterations. Here, we investigated the effect of lens-induced myopic growth on the distribution of retinal ganglion cells (RGCs), glial fibrillary acidic protein (GFAP) expression and intensity, and peripapillary retinal nerve fiber layer (ppRNFL) thickness in common marmosets (Callithrix jacchus) induced with myopia continuously for six months, using immunohistochemistry and spectral-domain optical coherence tomography. We also explored the relationship between cellular structural parameters and the photopic negative response (PhNR) using full-field electroretinography. Marmosets induced with myopia for six months developed axial myopia, had a thinner ppRNFL, reduced peripapillary ganglion cell (≈20%) and astrocyte density (≈42%), increased panretinal GFAP expression (≈42%) and nasal mid-periphery staining intensity (≈81%) compared to age-matched controls. Greater degrees of myopia and vitreous elongation were associated with reduced peripapillary RGCs and astrocyte density, and increased GFAP expression and intensity. These cellular structural changes did not show a significant relationship with the features of the PhNR, which remained unchanged. The outcomes of this study suggest that myopia induces a reorganization of the peripapillary inner retina at the cellular level that may not result in measurable functional repercussions at this stage of myopia development. Full article

TBM has been widely used in underground engineering and construction, but there is no precedent for the application of open TBM in the inclined shafts of coal mines, which brings new challenges to the support system. The distribution of the axial forces on anchors and the range of loosening of the surrounding rock are crucial considerations in tunnel support design. Existing methods for measuring the axial forces in anchors and determining the extent of loosening in the surrounding rock typically remain at the inspection level, lacking long-term and real-time monitoring capabilities. This paper presents a new self-sensing anchor with embedded optical fibers (made using an improved stirrer) and proposes an intelligent tunnel rock monitoring system. The paper also outlines a method for identifying loosening zones in surrounding rock based on monitoring data and theoretical analysis. Installing self-sensing anchors in the deep sections of the rock surrounding a tunnel provides three-dimensional, round-the-clock real-time monitoring of the axial forces acting on the anchors, using new technology and methods to recognize the deformation characteristics of loosening zones within the surrounding rock. This new self-sensing fiber optic anchor was first applied to an open TBM tunneling project in an inclined shaft in the Kekegai coal mine, and monitoring data indicate that self-sensing optical fiber anchors can accurately reflect stress patterns in real time. The axial force curve can be divided into four segments: the borehole area, the loosening zone, the stable zone, and the anchoring zone. Consequently, it accurately identifies the thickness of loosening zones at different positions within the tunnel’s surrounding rock. This information is compared and verified against results obtained from bolt dynamometers and borehole inspection. On this basis, an intelligent monitoring system was established to provide a basis for making engineering construction decisions, which makes tunnel construction smarter and helps technicians timely adjust TBM driving and support parameters. Full article

Currently, there is a lot of interest in smart sensors and integrated composite materials in various industries such as construction, aviation, automobile, medical, information technology, communication, and manufacturing. Here, a new conceptual design for a force and temperature sensor system is developed using fiber-optic Bragg grating sensors embedded within composite materials, and a mathematical model is proposed that allows one to estimate strain and temperature based on signals obtained from the optical Bragg gratings. This is important for understanding the behaviors of sensors under different conditions and for creating effective monitoring systems. Describing the strain gradient distribution, especially considering different materials with different Young’s modulus values, provides insight into how different materials respond to applied forces and temperature changes. The shape of the strain gradient distribution was obtained, which is a quadratic function with a maximum value of 1500 µ, with a maximum value at the center of the lattice and a symmetrically decreasing strain value with distance from the central part of the fiber Bragg grating. With the axial strain at the installation site of the Bragg grating sensor under applied force values ranging from 10 to 11 N, the change in strain was linear. As a result of theoretical research, it was found that the developed system with fiber-optic sensors based on Bragg gratings embedded in composite materials is resistant to external influences and temperature changes. Full article

Anti-resonant hollow core fibers (AR-HCFs) provide a promising solution for photothermal spectroscopy and photoacoustic imaging applications. Here, the AR-HCF serves as a micro platform to induce the photothermal/photoacoustic effect. Since the Bragg structure can induce multiple AR effects compared with the general AR-HCF, we proposed a novel device, the AR-BHCF (AR-HCF with Bragg cladding), to enhance the excitation efficiency. The simulation and experimental results validate that the AR-BHCF dominates in having a stronger ability to confine the optical field in the air core indeed. Then, the acoustic signal stimulated by the photoacoustic effect will propagate along with the fiber axial, and part of it will penetrate out of the AR-BHCF. The results revealed that the transmission bandwidth of the acoustic wave in the AR-BHCF ranges from 1 Hz to 1 MHz, covering infrasound to ultrasound. In particular, a constant coefficient of 0.5 exists in the acoustic wave fading process, related to the propagation frequency and time. The acoustic signal can be monitored in real time, assisted by the ultra-highly sensitive sensor head. Therefore, BHCF-based devices combined with photoacoustic techniques may accelerate their sensing applications. Meanwhile, this scheme shines a light on the theoretical foundation of novel short-haul distributed acoustic sensing. Full article

Optical fiber sensors are newly established gas pipeline leakage monitoring technologies with advantages, including high detection sensitivity to weak leaks and suitability for harsh environments. This work presents a systematic numerical study on the multi-physics propagation and coupling process of the leakage-included stress wave to the fiber under test (FUT) through the soil layer. The results indicate that the transmitted pressure amplitude (hence the axial stress acted on FUT) and the frequency response of the transient strain signal strongly depends on the types of soil. Furthermore, it is found that soil with a higher viscous resistance is more favorable to the propagation of spherical stress waves, allowing FUT to be installed at a longer distance from the pipeline, given the sensor detection limit. By setting the detection limit of the distributed acoustic sensor to 1 nε, the feasible range between FUT and the pipeline for clay, loamy soil and silty sand is numerically determined. The gas-leakage-included temperature variation by the Joule-Thomson effect is also analyzed. Results provide a quantitative criterion on the installation condition of distributed fiber sensors buried in soil for the great-demanding gas pipeline leakage monitoring applications. Full article

Based on high-stress characteristics of prestressed anchor cables, this paper develops an axial-distributed testing method to test corrosion damage of prestressed anchor cables. The positioning accuracy and corrosion range of an axial-distributed optical fiber sensor is studied, and its mathematical model between corrosion mass loss and axial fiber strain is established. The experimental results show that the fiber strain from an axial-distributed sensor enables one to reflect the corrosion rate along a prestressed anchor. Moreover, it has a greater sensitivity when an anchored cable has a higher stress. The mathematical model between corrosion mass loss and axial fiber strain is determined to be $\epsilon =4723.64\rho +2592.95$. The corrosion location along the anchor cable is characterized by axial fiber strain. Therefore, this work provides an insight for cable corrosion. Full article

Spacecraft is severely limited in weight and volume, resulting in a small bending radius of the fiber coil used by IFOG (Interference Fiber Optic Gyroscope). The fiber coil has such a size that the influence of bending on fiber birefringence cannot be ignored. In this paper, we research magnetic-induced errors of small-sized IFOG working in low orbit space. Firstly, we use the Jones matrix to analyze the effects of radial magnetic field and axial magnetic field on IFOG. Secondly, we establish a three-dimensional model for the radial magnetic-induced errors and magnetic-induced errors of minor radius fiber coil. Using the finite element method, we analyze the magnetic-induced error between different levels of the fiber coil. Combined with the birefringence distribution of the minor radius fiber coil, an accurate three-dimensional magnetic-induced error model is established. Thirdly, in the experiment, we design the magnetic-induced error test platform that includes the Fluke standard current source, transconductance amplifier, and Helmholtz coil. The experimental results show that, compared with the traditional calculation method, the three-dimensional magnetic-induced error model reduces the RMSE (Root Mean Square Error) of the radial magnetic field by 56.9% and the RMSE of the axial magnetic field by 35.7%, respectively. Full article

The anchoring quality of bolts is related to roadway safety and the surrounding rock stability. Due to the limitations of conventional monitoring methods in capturing strain, there still exists a gap in the real-time perception of the mechanical properties of bolts at the micro-scale. This paper proposes a new approach to detecting bolts’ anchoring qualities based on the fiber Bragg grating sensing principle. Moreover, it studies the strain transmission mechanism between the surface-bonded fiber Bragg grating and the bolt. A fiber-optic monitoring test platform of anchor bolt anchoring quality is built. The full-length anchor bolt’s strain evolution law and axial force distribution characteristics are studied during the pull-out test. The study results have shown that the theoretical value of the fiber strain transfer coefficient can be used to calculate the strain of the bolt. The bolt pull-out test verified the accuracy of using the fiber Bragg grating bolt axial force characterization equation to estimate the bolt stress. On the other hand, the correlation between the bolt axial force and the fiber Bragg grating monitoring value follows an exponential pattern. This study provides an important basis for improving the understanding of a bolt anchoring mechanism and the stability control of a roadway’s surrounding rock. Full article

In this paper, the field distribution and effective refractive index of transmission modes in single-core six-hole optical fiber were researched by modeling and simulation experiments. Based on the simulation results, a new type of sensor for axial strain, curvature, and temperature applications measurement was designed and fabricated. The experimental results showed that the axial strain sensitivities at different dips were −0.97 pm/με and −1.05 pm/με in the range from 0 to 2000 με, and the temperature sensitivities were 35.17 pm/°C and 47.27 pm/°C in the range from 25 to 75 °C. In addition, the proposed sensor also detected the curvature change with sensitivities of 7.36 dB/m⁻¹ and 20.08 dB/m⁻¹ from −2.582 m⁻¹ to −1.826 m⁻¹, respectively. Finally, through theoretical analysis, it can be deduced that this has potential application in the field of simultaneous measurement of strain and temperature. Full article

The temperature rise of the engaging clutch during shifting depends heavily on the transmitted torque. Precisely estimating the clutch temperature not only improves clutch control but also the optimal design of the clutch. However, the contact surface of the friction lining is closed, and the surface temperature is often difficult to measure accurately. In this study, a theoretical model of a two-dimensional transient temperature field for the friction disc has been established. In the radial and axial directions under different launching conditions, the temperature field of a friction disc is investigated. Four stages of clutch engagement have been determined, and finite-element analysis has been used to study the temperature field of a single clutch and to determine its duration.Then, the latest internationally developed distributed optical fiber sensing technology is used to perform measurement tests on the designed dry clutch friction characteristic test rig. The distributed fiber-optic temperature measurement technology can accomplish accurate temperature measurement with fast response speed and can acquire temperature value on different radii of friction discs with high spatial resolution. Such temperature sensing technology is very suitable for clutch working conditions. By analyzing the simulation and experimental results of temperature variation of different radii, different working conditions and different components, an important reference is provided for the establishment of the clutch temperature model and the optimization of the clutch heat dissipation structure design. Full article

Single-crystal fibers (SCFs) have a great application potential in high-power lasers due to their excellent performance. In this work, high-quality and crack-free Yb³⁺:Lu₃Al₅O₁₂ (Yb:LuAG) SCFs were successfully fabricated by the micro-pulling-down (μ-PD) technology. Based on the laser micrometer and the X-ray Laue diffraction results, these Yb:LuAG SCFs have a less than 5% diameter fluctuation and good crystallinity along the axial direction. More importantly, the distribution of Yb ions is proved to be uniform by electron probe microanalysis (EPMA) and the scanning electron microscope (SEM). In the laser experiment, the continuous-wave (CW) output power using a 1 mm diameter Yb:LuAG single-crystal fiber is determined to be 1.96 W, at the central wavelength of 1047 nm, corresponding to a slope efficiency of 13.55%. Meanwhile, by applying a 3 mm diameter Yb:LuAG SCF, we obtain a 4.7 W CW laser output at 1049 nm with the slope efficiency of 22.17%. The beam quality factor M² is less than 1.1 in both conditions, indicating a good optical quality of the grown fiber. Our results show that the Yb:LuAG SCF is a potential solid-state laser gain medium for 1 μm high-power lasers. Full article

Multiphoton microscopy is a well-established technique for biomedical applications, but real-time multidepth multimodal multiphoton microscopy using non-imaging detection has barely been discussed. We demonstrate a novel label-free imaging system capable of generating multimodal multiphoton signals at different focal planes simultaneously. Two spatially overlapped and temporally interlaced beams are obtained by applying cost-effective electro-optic modulator (EOM)-based fast-switching light paths. The switching beams have different divergence properties, enabling imaging at different depths into samples. The EOM is synchronized to the pixel clock from the microscope, achieving pixel-to-pixel focus-switching. The capability of the imaging system is demonstrated by performing real-time multidepth two-photon fluorescence (TPF) and second-harmonic generation (SHG) imaging of freshly excised mouse lung lobes. TPF and SHG images are acquired at two wavelength ranges. One is between 415 and 455 nm, and the other is between 495 and 635 nm. The microenvironment of pulmonary alveoli is depicted by the distributions of both elastin fibers visualized by TPF and collagen fibers illustrated by SHG. Macrophages residing inside apparent alveolar lumens are also identified by TPF, which shows that the imaging system is capable of localizing biological objects in three dimensions and has the potential of monitoring in vivo cellular dynamics in the axial direction. Full article

Three-dimensional braided composite has a unique spatial network structure that exhibits the characteristics of high delamination resistance, damage tolerance, and shear strength. Considering the characteristics of braided structures, two types of high-performance materials, namely, aramid and carbon fibers, were used as reinforcements to prepare braided composites with different hybrid structures. In this study, the longitudinal and transverse shear properties of 3D braided hybrid composites were tested to investigate the influences of hybrid and structural effects. The damage characteristics of 3D braided hybrid composites under short beam shear loading underwent comprehensive morphological analysis via optical microscopy, water-logging ultrasonic scanning, and X-ray micro-computed tomography methods. It is shown that the shear toughness of hybrid braided composite has been improved at certain degrees compared with the pure carbon fiber composite under both transverse and longitudinal directions. The hybrid braided composites with aramid fiber as axial yarn and carbon fiber as braiding yarn exhibited the best shear toughness under transverse shear loading. Meanwhile, the composites with carbon fiber as axial yarn and aramid fiber as braiding yarn demonstrated the best shear toughness in the longitudinal direction. Due to the different distribution of axial and braiding yarns, the transverse shear property of hybrid braided structure excels over the longitudinal shear property. The failure modes of the hybrid braided composite under the two loading directions are considerably different. Under transverse loading, the primary failure mode of the composites is yarn fracture. Under longitudinal loading, the primary failure modes are resin fracture and fiber slip. The extensive interfacial effects and the good deformation capability of the hybrid braided composites can effectively prevent the longitudinal development of internal cracks in the pattern, improving the shear properties of braided composites. Full article

In the past two decades Brillouin-based sensors have emerged as a newly-developed optical fiber sensing technology for distributed temperature and strain measurements. Among these, the Brillouin optical time domain reflectometer (BOTDR) has attracted more and more research attention, because of its exclusive advantages, including single-end access, simple system architecture, easy implementation and widespread field applications. It is realized mainly by injecting optical pulses into the fiber and detecting the Brillouin frequency shift (BFS), which is linearly related to the change of ambient temperature and axial strain of the sensing fiber. In this paper, the authors provide a review of new progress on performance improvement and applications of BOTDR in the last decade. Firstly, the recent advances in improving the performance of BOTDRs are summarized, such as spatial resolution, signal-to-noise ratio and measurement accuracy, measurement speed, cross sensitivity and other properties. Moreover, novel-type optical fibers bring new characteristics to optic fiber sensors, hence we introduce the different Brillouin sensing features of special fibers, mainly covering the plastic optical fiber, photonic crystal fiber, few-mode fiber and other special fibers. Additionally, we present a brief overview of BOTDR application scenarios in many industrial fields and intelligent perception, including structural health monitoring of large-range infrastructure, geological disaster prewarning and other applications. To conclude, we discuss several challenges and prospects in the future development of BOTDRs. Full article