Search Results (49)

This study presents an innovative approach to designing a shoe insole with enhanced durability, sustainability, and antibacterial properties. Needle-punched non-woven recycled polyester fabrics with three different GSMs (100, 200, and 300) were developed. The composite shoe insole was developed using non-woven fabric laminated with a polyurethane sheet to enhance durability. The fabrics were treated with an antibacterial finish with three different concentrations (5%, 10%, and 15%) and subjected to 5 and 10 washing cycles. The developed composites were evaluated against their relative hand value, abrasion resistance, tensile strength, antibacterial activity, and overall moisture management capability. Overall results reveal that the developed composite shoe insole is durable, sustainable, and presents no bacterial growth, demonstrating the insole’s hygienic effectiveness. Full article

Air pollution is currently the most significant environmental factor posing a threat to the health and lives of European residents. It is a key cause of poor health, particularly respiratory and cardiovascular diseases. The primary aim of the study was to numerically determine the impact of the air purifier model’s geometry on the distribution of air within a room and to conduct experimental tests on the filtration efficiency and preliminary antibacterial activity of filtration composites. The scope of the work included designing an air purifier model in the form of a pendant lamp and performing computer simulations in Ansys software to identify the optimal shape. The experimental research focused on developing filtration composites consisting of nonwoven fabric with an active hydrosol layer, meltblown nonwovens and a carbon filter. The study results showed that the SMMS composite with 50% thyme and carbon nonwoven exhibited the highest filtration efficiency for both small and large particles. Full article

Alginate-based materials have gained significant recognition in the medical industry due to their favorable biochemical properties. As a continuation of our previous studies, we have introduced a new composite consisting of cellulose nonwoven fabric charged with a metallic copper core (CNW-Cu⁰) covered with a calcium alginate (ALG⁻Ca²⁺) layer. The preparation process for these materials involved three main steps: coating the cellulose nonwoven fabric with copper via magnetron sputtering (CNW → CNW-Cu⁰), subsequent deposition with sodium alginate (CNW-Cu⁰ → CNW-Cu⁰/ALG⁻Na⁺), followed by cross-linking the alginate chains with calcium ions (CNW-Cu⁰/ALG⁻Na⁺ → CNW-Cu⁰/ALG⁻Ca²⁺). The primary objective of the work was to supply these composites with such biological attributes as antibacterial and hemostatic activity. Namely, equipping the antibacterial materials (copper action on representative Gram-positive and Gram-negative bacteria and fungal strains) with induction of blood plasma clotting processes (activated partial thromboplastin time (aPTT) and prothrombin time (PT)). We determined the effect of CNW-Cu⁰/ALG⁻Ca²⁺ materials on the viability of Peripheral blood mononuclear (PBM) cells. Moreover, we studied the interactions of CNW-Cu⁰/ALG⁻Ca²⁺ materials with DNA using the relaxation plasmid assay. However, results showed CNW-Cu⁰/ALG⁻Ca²⁺’s cytotoxic properties against PBM cells in a time-dependent manner. Furthermore, the CNW-Cu⁰/ALG⁻Ca²⁺ composite exhibited the potential to interact directly with DNA. The results demonstrated that the CNW-Cu⁰/ALG⁻Ca²⁺ composites synthesized show promising potential for wound dressing applications. Full article

ZnO nanorod nonwoven fabrics (ZNRN) were developed through hydrothermal synthesis to facilitate the prevention of the transmission of respiratory pathogens. The superhydrophobicity and antibacterial properties of ZNRN were improved through the response surface methodology. The synthesized material exhibited significant water repellency, indicated by a water contact angle of 163.9°, and thus demonstrated antibacterial rates of 91.8% for Escherichia coli (E. coli) and 79.75% for Staphylococcus aureus (S. aureus). This indicated that E. coli with thinner peptidoglycan may be more easily killed than S. aureus. This study identified significant effects of synthesis conditions on the antibacterial effectiveness, with comprehensive multivariate analyses elucidating the underlying correlations. In addition, the ZnO nanorod structure of ZNRN was characterized through SEM and XRD analyses. It endows the properties of superhydrophobicity (thus preventing bacteria from adhering to the ZNRN surface) and antibacterial capacity (thus damaging cells through the puncturing of these nanorods). Consequently, the alignment of two such features is desired to help support the development of personal protective equipment, which assists in avoiding the spread of respiratory infections. Full article

This is the first study of non-woven fabrics elaborated by melt-blowing from polymer nanocomposites made of Nylon 6 and nanoclay (Cloisite 20A) modified with an amine (1,4 diaminobutane dihydrochloride). Morphological and physical characteristics, adsorption capacity, and antibacterial properties are presented. From the X-ray diffraction (XRD) results, it was possible to observe a displacement of the signals to other 2θ angles, due to an α to ϒ phase shift. The scanning electron microscopy (SEM) images showed that the mean diameter of fiber decreased as the content of nanoclay increased. The mechanical tests showed that the tear strength force of neat nylon was 1.734 N, but this characteristic increased to 2.135 N for the sample with 0.5% modified nanoclay. The inulin adsorption efficiency of the Nylon 6/C20A 1.5% and Nylon 6/C20A 2% samples at 15 min was 75 and 74%, respectively. The adsorption capacity of Nylon 6/C20A 1.5% and Nylon 6/C20A 2% for methylene blue and methyl orange remained above 90% even after four adsorption cycles. In addition, non-woven fabrics present antibacterial activity against E. coli. Full article

This article presents the biochemical properties of poly(lactide)-zinc (PLA-Zn) composites obtained by DC magnetron sputtering of zinc onto melt-blown nonwoven fabrics. The biochemical properties were determined by the evaluation of the activated partial thromboplastin time (aPTT) and prothrombin time (PT). The antimicrobial activity of the PLA-Zn samples was additionally tested against representative Gram-positive and Gram-negative bacteria strains. A structural study of the PLA-Zn has been carried out using specific surface area and total pore volume (BET) analysis, as well as atomic absorption spectrometry with flame excitation (FAAS). PLA-Zn composites exhibited an antibacterial effect against the analyzed strains and produced inhibition zones against E. coli and S. aureus. Biochemical investigations revealed that the untreated PLA fibers caused the acceleration of the clotting of human blood plasma in the intrinsic pathway. However, the PLA-Zn composites demonstrated significantly different properties in this regard, the aPTT was prolonged while the PT was not altered. Full article

The multifunctional development in the field of face masks and the growing demand for scalable manufacturing have become increasingly prominent. In this study, we utilized high-vacuum magnetron sputtering technology to deposit a 5 nm ultra-thin Ag–Cu film on non-woven fabric and fabricated ultra-thin Ag–Cu film face masks. The antibacterial rates against Escherichia coli and Staphylococcus aureus were 99.996% and 99.978%, respectively, while the antiviral activity against influenza A virus H1N1 was 99.02%. Furthermore, the mask’s ability to monitor respiratory system diseases was achieved through color change (from brownish-yellow to grey-white). The low cost and scalability potential of ultra-thin silver–copper film masks offer new possibilities for practical applications of multifunctional masks. Full article

With the stricter emission regulations for internal combustion engines, electric vehicles, including electrically powered port tractors, have received increasing attention. However, currently, most of the filters used in electric vehicles are conventional membranes that only have the function of filtering particles and foreign objects. Therefore, in order to improve the above issues, the surface of commercial non-woven filter membranes was coated with Ag nanopowder nanofibers and AgNO₃ nanofibers via electrospinning. At present, the comparative research on the antibacterial ability of Ag nanopowder and AgNO₃ is still blank in the same research system, especially with the use of electrospun coating technology. The morphologies and structures of non-woven fabrics and electrospinning coated samples were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The characterization results indicate that both pure PVA and PVA composite fibers can be successfully coated on the surface of non-woven fabrics. The average diameter of all electrospun PVA composite fibers is distributed in the range of 470–700 nm. The PVA nanofibers with a low content of 1 wt% AgNO₃ have good antibacterial properties against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus), with clearance clear zones of inhibition of 26.00 mm and 17.30 mm, respectively. Full article

The paper presents the investigation of the biological properties of Poly(Lactide)—Copper composite material obtained by sputter deposition of copper onto Poly(lactide) melt-blown nonwoven fabrics. The functionalized composite material was subjected to microbial activity tests against colonies of Gram-positive (Staphylococcus aureus), Gram-negative (Escherichia coli, Pseudomonas aeruginosa) bacteria, Chaetomium globosum and Candida albicans fungal mold species and biochemical–hematological tests including the evaluation of the Activated Partial Thromboplastin Time, Prothrombin Time, Thrombin Time and electron microscopy fibrin network imaging. The substantial antimicrobial and antifungal activities of the Poly(Lactide)–Copper composite suggests potential applications as an antibacterial/antifungal material. The unmodified Poly(Lactide) fabric showed accelerated human blood plasma clotting in the intrinsic pathway, while copper plating abolished this effect. Unmodified PLA itself could be used for the preparation of wound dressing materials, accelerating coagulation in the case of hemorrhages, and its modifications with the use of various metals might be applied as new customized materials where blood coagulation process could be well controlled, yielding additional anti-pathogen effects. Full article

Limited efficiency, lower durability, moisture absorbance, and pest/fungal/bacterial interaction/growth are the major issues relating to porous nonwovens used for acoustic and thermal insulation in buildings. This research investigated porous nonwoven textiles composed of recycled cotton waste (CW) fibers, with a specific emphasis on the above-mentioned problems using the treatment of silicon coating and formation of nanofibers via facile-solution processing. The findings revealed that the use of an economic and eco-friendly superhydrophobic (contact angle higher than 150°) modification of porous nonwovens with silicon nanofibers significantly enhanced their intrinsic characteristics. Notable improvements in their compactness/density and a substantial change in micro porosity were observed after a nanofiber network was formed on the nonwoven material. This optimized sample exhibited a superior performance in terms of stiffness, surpassing the untreated samples by 25–60%. Additionally, an significant enhancement in tear strength was observed, surpassing the untreated samples with an impressive margin of 70–90%. Moreover, the nanofibrous network of silicon fibers on cotton waste (CW) showed significant augmentation in heat resistance ranging from 7% to 24% and remarkable sound absorption capabilities. In terms of sound absorption, the samples exhibited a performance comparable to the commercial standard material and outperformed the untreated samples by 20% to 35%. Enhancing the micro-roughness of fabric via silicon nanofibers induced an efficient resistance to water absorption and led to the development of inherent self-cleaning characteristics. The antibacterial capabilities observed in the optimized sample were due to its superhydrophobic nature. These characteristics suggest that the proposed nano fiber-treated nonwoven fabric is ideal for multifunctional applications, having features like enhanced moisture resistance, pest resistance, thermal insulation, and sound absorption which are essential for wall covers in housing. Full article

In recent years, Electrospinning (ES) has been revealed to be a straightforward and innovative approach to manufacture functionalized nanofiber-based membranes with high filtering performance against fine Particulate Matter (PM) and proper bioactive properties. These qualities are useful for tackling current issues from bacterial contamination on Personal Protective Equipment (PPE) surfaces to the reusability of both disposable single-use face masks and respirator filters. Despite the fact that the conventional ES process can be upscaled to promote a high-rate nanofiber production, the number of research works on the design of hybrid materials embedded in electrospun membranes for face mask application is still low and has mainly been carried out at the laboratory scale. In this work, a multi-needle ES was employed in a continuous processing for the manufacturing of both pristine Poly (Vinylidene Fluoride-co-Hexafluoropropylene) (PVDF-HFP) nanofibers and functionalized membrane ones embedded with TiO₂ Nanoparticles (NPs) (PVDF-HFP@TiO₂). The nanofibers were collected on Polyethylene Terephthalate (PET) nonwoven spunbond fabric and characterized by using Scanning Electron Microscopy and Energy Dispersive X-ray (SEM-EDX), Raman spectroscopy, and Atomic Force Microscopy (AFM) analysis. The photocatalytic study performed on the electrospun membranes proved that the PVDF-HFP@TiO₂ nanofibers provide a significant antibacterial activity for both Staphylococcus aureus (~94%) and Pseudomonas aeruginosa (~85%), after only 5 min of exposure to a UV-A light source. In addition, the PVDF-HFP@TiO₂ nanofibers exhibit high filtration efficiency against submicron particles (~99%) and a low pressure drop (~3 mbar), in accordance with the standard required for Filtering Face Piece masks (FFPs). Therefore, these results aim to provide a real perspective on producing electrospun polymer-based nanotextiles with self-sterilizing properties for the implementation of advanced face masks on a large scale. Full article

In this paper, we report an antibacterial, recyclable nanocellulose–titanium dioxide/polyester nonwoven fabric (NC-TiO₂/PET) composite for the highly efficient photocatalytic degradation of dyes. The NC-TiO₂ was loaded onto the surface of flexible PET nonwoven fabric through a simple swelling and dipping method. The NC-TiO₂ in the particle size range of ~10 nm were uniformly attached to the surface of the PET fibers. The NC-TiO₂/PET composite has the ability to achieve the stable photocatalytic degradation of dyes and presents antibacterial properties. The degradation rates to methylene blue (MB) and acid red (AR) of the NC-TiO₂/PET composite reached 90.02% and 91.14%, respectively, and the inhibition rate of Escherichia coli was >95%. After several rounds of cyclic testing, the photocatalytic performance, antibacterial performance, and mechanical stability of the NC-TiO₂/PET composite remained robust. Full article

Polypropylene melt-blown nonwoven fabric (PP MNF) masks can effectively block pathogens in the environment from entering the human body. However, the adhesion of surviving pathogens to masks poses a risk of human infection. Thus, embedding safe and efficient antibacterial materials is the key to solving pathogen infection. In this study, stable chlorinated poly(methacrylamide-N,N′-methylenebisacrylamide) polypropylene melt-blown nonwoven fabrics (PP-P(MAA-MBAA)-Cl MNFs) have been fabricated by a simple UV cross-link and chlorination process, and the active chlorine content can reach 3500 ppm. The PP-P(MAA-MBAA)-Cl MNFs show excellent hydrophilic and antibacterial properties. The PP-P(MAA-MBAA)-Cl MNFs could kill all bacteria (both Escherichia coli and Staphylococcus aureus) with only 5 min of contact. Therefore, incorporating PP-P(MAA-MBAA)-Cl MNF as a hydrophilic antimicrobial layer into a four-layer PP-based mask holds great potential for enhancing protection and comfort. Full article

Literature reviews have described the applications of silver, copper, and zinc ions and metallic particles of Cu, Ti, and Zn oxides, which have been found to be useful antimicrobial reagents for the biofunctionalization of various materials and their surfaces. For this purpose, compositions of water dispersions containing emulsions of synthetic copolymers based on acrylic and vinyl monomers, polysaccharides (hydroxyethyl cellulose and starch), and various additives with wetting and stabilizing properties were used. Many stable water dispersions of different chemical compositions containing bioactive chemical compounds (copper silicate hydrate, titanium dioxide, and zinc oxide (and other auxiliary substances)) were developed. They were used for the preparation of thin hybrid coatings having good antimicrobial properties against Gram-negative bacteria (Escherichia coli), Gram-positive bacteria (Staphylococcus aureus), and yeast fungus (Candida albicans). Polyester (PES) and polylactide (PLA) nonwovens were modified using the dip-coating method, while PES and cotton fabrics were biofunctionalized by means of dip-coating and coating methods. The antimicrobial (antibacterial and antifungal) properties of the textile materials (nonwovens and fabrics) biofunctionalized with the above-mentioned bioactive agents exhibiting antimicrobial properties (CuSiO₃, TiO₂, ZnO, or ZnO∙SiO₂) were strongly dependent on the agents’ content in the water dispersions. The PES and PLA nonwovens, modified on the surface with water compositions containing copper silicate hydrate, showed good antibacterial properties against the Gram-negative bacteria Escherichia coli, even at a content of 1 wt.% CuSiO₃∙xH₂O, and against the Gram-positive bacteria Staphylococcus aureus, at the content of at least 5 wt.% CuSiO₃∙xH₂O. The bacterial growth reduction factor (R) was greater than 99% for most of the samples tested. Good antifungal properties against the fungus Candida albicans were found for the PES and PLA nonwoven fabrics modified with dispersions containing 5–7 wt.% CuSiO₃∙xH₂O and 4.2–5.0 wt.% TiO₂. The addition of TiO₂ led to a significant improvement in the antifungal properties of the PES and PLA nonwovens modified in this way. For the samples of PES WIFP-270 and FS F-5 nonwovens, modified with water dispersions containing 5.0 wt.% CuSiO₃∙xH₂O and 4.2–5.0 wt.% TiO₂, the growth reduction factor for the fungus Candida albicans (R) reached values in the range of 80.9–98.0%. These new biofunctionalized polymeric nonwoven textile materials can find practical applications in the manufacture of filters for hospital air-conditioning systems and for the automotive industry, as well as in air purification devices. Moreover, similar antimicrobial modification of fabrics with the dip-coating or coating methods can be applied, for example, in the fabrication of fungi- and mold-resistant garden furniture. Full article

Antibacterial nonwoven fabrics, incorporated with Ag, have been applied as masks and air conditioner filters to prevent the spread of disease from airborne respiratory pathogens. In this work, we present a comparison study of Ag ions: Ag and AgCu nanoparticles (NPs) coated onto nonwoven fabrics intended for use as air conditioner antibacterial filters. We illustrate their color changes and durability running in air conditioners using antibacterial activity testing and X-ray Photoelectron Spectroscopic (XPS) analysis. We found that AgCu NPs showed the best antibacterial efficacy and durability. XPS analysis indicated that the Ag concentration, on both the AgCu and Ag- NP-coated fibers, changed little. On the contrary, the Ag concentration on Ag ion-coated fibers decreased by ~30%, and the coated NPs aggregated over time. The color change in AgCu NP-coated fabric, from yellow to white, is caused by oxide shell formation over the NPs, with nearly 46% oxidized silver. Our results, both from antibacterial evaluation and wind blowing tests, indicate that AgCu NP-coated fibers have higher durability, while Ag ion-coated fibers have little durability in such applications. The enhanced durability of the AgCu NP-coated antibacterial fabrics can be attributed to stronger NP–fiber interactions and greater ion release. Full article