Search Results (1,418)

This paper assesses the feasibility of metakaolin (MK)-based geopolymer (GP) composite as an environmentally friendly substitute for cement-based composite in repair applications. The Taguchi orthogonal array method was used to find the optimum GP mix in terms of mechanical properties and adhesion to concrete substrates. Four key parameters, each with three levels, are investigated including the alkaline activator-to-MK ratio (A/M: 1, 1.2, 1.4), the sodium silicate-to-sodium hydroxide ratio (S/H: 2.0, 2.5, 3.0), sodium hydroxide (SH) molarity (12, 14, 16), and curing temperature (30, 45, 60 °C). The evaluated properties include flowability, compressive strength, splitting tensile strength, flexural strength, ultrasonic pulse velocity, and bond strength under various interface configurations. Experimental results demonstrated that the performance of MK-based GP composite was primarily governed by the A/M ratio and sodium hydroxide molarity. The Taguchi optimization method revealed that the mix design featuring A/M of 1.4, SS/SH of 2, 16 M sodium hydroxide, and curing at 60 °C yielded notable improvements in compressive and bond strengths compared to conventional cement-based composites. Full article

Beta (β)-type Ti-29Nb-13Ta-4.6Zr (TNTZ) alloys combine low modulus with biocompatibility but require improved surface properties for long-term implantation. This study aimed to enhance the surface mechanical strength and antibacterial performance of TNTZ by applying TiN and TiAlN coatings via PVD. Notably, TiAlN was deposited on TNTZ for the first time, enabling a direct side-by-side comparison with TiN under identical deposition conditions. Dense TiN (~1.06 μm) and TiAlN (~1.73 μm) coatings were deposited onto solution-treated TNTZ and characterized by X-ray diffraction, scanning probe microscopy, Vickers microhardness, Rockwell indentation test (VDI 3198), static water contact angle measurements, and a Kirby–Bauer disk-diffusion antibacterial assay against Escherichia coli (E. coli). Both coatings formed face-centered cubic (FCC) structures with smooth interfaces (Ra ≤ 5.3 nm) while preserving the single-phase β matrix of the substrate. The hardness increased from 192 HV (uncoated) to 1059 HV (TiN) and 1468 HV (TiAlN), and the adhesion quality was rated as HF2 and HF1, respectively. The surface wettability changed from hydrophilic (48°) to moderately hydrophobic (82°) with TiN and highly hydrophobic (103°) with TiAlN. Similarly, the diameter of the no-growth zones increased to 18.02 mm (TiN) and 19.09 mm (TiAlN) compared to 17.65 mm for uncoated TNTZ. The findings indicate that TiAlN, in particular, provided improved hardness, adhesion, and hydrophobicity. Preliminary bacteriostatic screening under diffusion conditions suggested a modest relative antibacterial response, though the effect was not statistically significant between coated and uncoated TNTZ. Statistical analysis confirmed no significant difference between the groups (p > 0.05), indicating that only a preliminary bacteriostatic trend— rather than a definitive antibacterial effect—was observed. Both nitride coatings strengthened TNTZ without compromising its structural integrity, making TiAlN-coated TNTZ a promising candidate for next-generation orthopedic implants. Full article

Prostate stem cell antigen (PSCA) is a Ly6/uPAR protein that targets neuronal nicotinic acetylcholine receptors (nAChRs). It exists in membrane-tethered and soluble forms, with the latter upregulated in Alzheimer’s disease. We hypothesize that PSCA may be linked to a wider spectrum of neurological diseases and could induce neuroinflammation. Indeed, PSCA expression is significantly upregulated in the brain of patients with multiple sclerosis, Huntington’s disease, Down syndrome, bipolar disorder, and HIV-associated dementia. To investigate PSCA’s structure, pharmacology, and inflammatory function, we produced a correctly folded water-soluble recombinant analog (ws-PSCA). In primary hippocampal neurons and astrocytes, ws-PSCA differently regulates secretion of inflammatory factors and adhesion molecules and induces pro-inflammatory responses by increasing TNFβ secretion. Heteronuclear NMR and ¹⁵N relaxation measurements reveal a classical β-structural three-finger fold with conformationally disordered loops II and III. Positive charge clustering on the molecular surface suggests the functional importance of ionic interactions by these loops. Electrophysiological studies in Xenopus oocytes point on ws-PSCA inhibition of α3β2-, high-, and low-sensitive variants of α4β2- (IC₅₀ ~50, 27, and 15 μM, respectively) but not α4β4-nAChRs, suggesting targeting of the β2 subunit. Ensemble docking and molecular dynamics simulations predict PSCA binding to high-sensitive α4β2-nAChR at α4/β2 and β2/β2 interfaces. Complexes are stabilized by ionic and hydrogen bonds between PSCA’s loops II and III and the primary and complementary receptor subunits, including glycosyl groups. This study gives new structural and functional insights into PSCA’s interaction with molecular targets and provides clues to understand its role in the brain function and mental disorders. Full article

This study aims to evaluate the tribological performance of commercial PVD coatings in alleviating material transfer under unlubricated contact in the hot forming of aluminum alloy. The commercial PVD coatings included AlCrN, TiAlN, and Arc-DLC coatings, deposited on the forming tool surface. The warm and hot upsetting sliding test (WHUST) was used as a friction test in this study to reproduce the severe contact conditions from the hot forming process of AA6082-T6 aluminum alloy. The WHUST was performed at 300 °C, 400 °C, and 500 °C to investigate the effect of temperature on the tribological performance of each coating. The results found that the AlCrN and TiAlN coatings exhibited similar performance. They dominated the initial aluminum transfer by adhesive bonding. In contrast, the Arc-DLC coating mainly caused the initial aluminum transfer by mechanical plowing due to its lower chemical affinity to the aluminum alloy. In addition, the tribological performance of each coating highly depended on the temperature. Higher temperatures resulted in both stronger intermetallic bonding at the interface and lower yield strength of the aluminum alloy. These behaviors led to the variations in the coefficient of friction, the 3D topography and the SEM morphology along the wear track of the specimen, and the thickness of the adhered aluminum layer on the coating surface. In comparison, the Arc-DLC coating provided better tribological performance in mitigating the aluminum transfer than the others. Full article

Hexagonal boron nitride (h-BN) possesses a unique combination of a wide bandgap, high thermal conductivity, and chemical inertness, making it a key insulating and thermal management material for advanced electronics and nanocomposites. However, its intrinsic hydrophobicity and strong interlayer van der Waals forces severely limit exfoliation efficiency and dispersion stability, particularly in scalable liquid-phase processes. Here, we report a synergistic exfoliation strategy that integrates acid-induced hydroxylation with gallium (Ga) intercalation to achieve high-yield (>80%) production of ultrathin (<4 nm) hydrophilic h-BN nanosheets. Hydroxylation introduces abundant -OH groups, expanding interlayer spacing and significantly increasing surface polarity, while Ga intercalation leverages its native Ga₂O₃ shell to form strong interfacial interactions with hydroxylated basal planes. This oxide-mediated adhesion facilitates efficient layer separation under mild sonication, yielding nanosheets with well-preserved lateral dimensions and exceptional dispersion stability in polar solvents. Comprehensive characterization confirms the sequential chemical and structural modifications, revealing the crucial roles of hydroxylation-induced activation and Ga₂O₃ assisted wettability enhancement. This combined chemical activation–soft metallic intercalation approach provides a scalable, solution-processable route to high-quality h-BN nanosheets, opening new opportunities for their integration into dielectric, thermal interface, and multifunctional composite systems. Full article

This work presents a novel Gallium Nitride (GaN) high-electron-mobility transistor (HEMT)-based ultraviolet (UV) photodetector architecture that integrates advanced material and structural design strategies to enhance detection performance and stability under room-temperature operation. This study is conducted as a fully numerical simulation using the Silvaco Atlas platform, providing detailed electrothermal and optoelectronic analysis of the proposed device. The device is constructed on a high-thermal-conductivity silicon carbide (SiC) substrate and incorporates an n-GaN buffer, an indium nitride (InN) channel layer for improved electron mobility and two-dimensional electron gas (2DEG) confinement, and a dual-passivation scheme combining silicon nitride (SiN) and hexagonal boron nitride (h-BN). A p-GaN layer is embedded between the passivation interfaces to deplete the 2DEG in dark conditions. In the device architecture, the metal contacts consist of a 2 nm Nickel (Ni) adhesion layer followed by Gold (Au), employed as source and drain electrodes, while a recessed gate embedded within the substrate ensures improved electric field control and effective noise suppression. Numerical simulations demonstrate that the integration of a hexagonal boron nitride (h-BN) interlayer within the dual passivation stack effectively suppresses the gate leakage current from the typical literature values of the order of ${10}^{-8}$ A to approximately ${10}^{-10}$ A, highlighting its critical role in enhancing interfacial insulation. In addition, consistent with previous reports, the use of a SiC substrate offers significantly improved thermal management over sapphire, enabling more stable operation under UV illumination. The device demonstrates strong photoresponse under 360 nm ultraviolet (UV) illumination, a high photo-to-dark current ratio (PDCR) found at approximately ${10}^6$, and tunable performance via structural optimization of p-GaN width between 0.40 μm and 1.60 μm, doping concentration from $5\times {10}^{16}$ ${\mathrm{cm}}^{-3}$ to $5\times {10}^{18}$ ${\mathrm{cm}}^{-3}$, and embedding depth between 0.060 μm and 0.068 μm. The results underscore the proposed structure’s notable effectiveness in passivation quality, suppression of gate leakage, and thermal management, collectively establishing it as a robust and reliable platform for next-generation UV photodetectors operating under harsh environmental conditions. Full article

Focusing on the practical application requirements of adhesive-bonded structures in aerospace engineering, this study aims to investigate the mechanical performance and failure mechanisms of adhesive interfaces. Adhesive bonding, valued for its uniform load distribution, low stress concentration, superior sealing, and lightweight properties, serves as a critical joining technology in aerospace engineering. However, its reliable application is constrained by complex multimode failure issues, such as cohesive failure, interfacial debonding, and matrix damage. To address these challenges, a comprehensive evaluation of the novel high-strength epoxy adhesive Dq622JD-136 (Adhesive III) was conducted through systematic tests, including bulk tension, butt joint tension, single lap shear, compressive shear, and fracture toughness (TDCB/ENF) tests. These tests characterized its mechanical properties and fracture behavior under mode-I and mode-II loading, with comparative analyses against conventional adhesives HYJ-16 (Adhesive I) and HYJ-29 (Adhesive II). Key findings reveal that Adhesive III exhibits outstanding elastic modulus, significantly outperforming the comparative adhesives. While its normal and shear strengths are slightly lower than Adhesive I, they surpass Adhesive II. A common characteristic across all adhesives is that normal strength exceeds shear strength. In terms of fracture toughness, Adhesive III demonstrates superior mode-II toughness but relatively lower mode-I toughness. These results elucidate the brittle characteristics of such adhesives, mixed failure modes under normal loading, and cohesive failure behavior under shear loading. The innovation of this work lies in systematically correlating the macroscopic performance of adhesives with failure mechanisms through multi-dimensional testing. Its findings provide critical technical support for multiscale performance evaluation and adhesive selection in aerospace joints subjected to extreme thermomechanical loads. Full article

Steel–timber composite (STC) structures offer a sustainable and low-carbon structural solution. Steel–timber interface behavior is critical for the mechanical performance of STC structures. This paper introduces a novel connection for steel–timber composites (STC) that combines mechanical interlocking with adhesive bonding through an epoxy-bonded bolted design. Epoxy resin is injected into the timber dowel slots, followed by pre-tightening of the bolts, forming a composite dowel system where the ‘bolt–epoxy resin–timber’ components work in synergy. The load–displacement characteristics and failure modes of nine specimen groups were investigated through a series of double-shear push-out tests. The influence of a wide range of connector parameters on the stiffness, shear bearing capacity, and ductility of STC joints was systematically investigated. The parameters included fastener strength grade, thread configuration, diameter, number, and the use of epoxy resin reinforcement. The experimental results demonstrated that high-strength partially threaded bolts were crucial for achieving a synergy of high load-bearing capacity and commendable ductility, while full-threaded bolts exhibited vulnerability to brittle shear failure, a consequence of stress concentration at the root of the threads. Although screw connections provided enhanced initial stiffness through timber anchorage, ordinary bolt connections exhibited superior ultimate load-bearing capacity. In comparison with conventional bolt connections, epoxy resin–bolt connections exhibited enhanced mechanical properties, with an augmentation in ultimate load and initial stiffness of 12% and 11.8%, respectively, without sacrificing ductility. Full article

Background: The use of zirconia-based restorations has increased in dentistry due to their aesthetics, high strength, and biocompatibility. However, achieving durable adhesion between resin cements and zirconia remains a challenge in restorative dentistry. Adhesive failures can lead to complications ranging from dentin hypersensitivity to the loss of the restored tooth. This review evaluates the impact of surface treatments based on silica coatings as a strategy to improve the adhesion of resin cements to zirconia. Methods: A systematic review was conducted following PRISMA guidelines. Searches were performed in Scopus, Web of Science, PubMed, EBSCO, and ScienceDirect. In vitro studies were included if they (1) evaluated silica-based coatings on zirconia surfaces; (2) measured bond strength at the zirconia–cement interface through shear tests (MPa) and reported failure type (adhesive, cohesive, mixed); (3) used ≥8 specimens per group; and (4) included an untreated zirconia control group. Data were extracted and compared for conditions before and after thermocycling in the studies that reported this procedure. Results: The average bond strength for silica-coated zirconia was 15 MPa without thermocycling and 11.97 MPa after thermocycling, regardless of the coating technique. These values were significantly higher than those of untreated zirconia (8.45 MPa and 6.41 MPa, respectively). Cohesive and mixed failures predominated in silica-treated groups, suggesting more effective adhesion compared to controls, which presented mainly adhesive failures. Conclusions: Silica coatings, especially when combined with adhesion promoters, MDP-based primers, significantly enhance the bond strength of resin cements to zirconia. This reduces the risk of secondary caries, sensitivity, restoration debonding, and potential tooth fractures. However, the effectiveness of these coatings varies depending on the technique used, suggesting the need to standardize protocols to optimize clinical outcomes. Full article

In this study, the properties of electrophoretically deposited (EPD) coatings on orthodontic implants made from Ti-6Al-4V alloy were evaluated during simulated implantation trials on animal bones. Three types of chitosan-based coatings were prepared using EPD: titanium nitride microparticles (TiNPs), titanium nitride nanoparticles (TiNNPs), and boron nitride particles (BNPs). Each of these coatings was also modified by adding a polylactic acid (PLA) layer using a dip-coating technique to compare their properties with and without this additional layer. The coatings were analysed using optical microscopy, confocal microscopy, and scanning electron microscopy (SEM) with elemental analysis. Surface roughness measurements of the coated implants were also conducted to highlight differences that could significantly influence the type and strength of the bone-implant interface, directly affecting the stability of the implant as an anchorage unit. Eventually, to evaluate the antibacterial properties of the EPD coatings, their antibacterial activity against both Gram-positive and Gram-negative bacteria strains was tested. Scanning electron observations confirmed the homogenous distribution of micro- and nanoparticles in all coatings. The highest surface roughness values were observed in layers containing titanium nitride nanoparticles (TiNNPs) and chitosan. The presence of an additional dip-coating PLA layer improved the adhesion, and its effect on the surface roughness depended on the particle size. While the antibacterial properties of the coatings show promising results, achieving optimal adhesion of the coatings to implants remains a challenge that requires further development. Full article

Background: We evaluated the immediate and artificially aged micro-tensile bond strengths (μTBS) of Hi-Bond Universal, a universal adhesive containing mesoporous bioactive glass (MBG). Methods: Human dentin specimens were bonded using the following four application modes: Hi-Bond Universal in etch-and-rinse mode, Hi-Bond Universal in self-etch mode, Single Bond 2 in etch-and-rinse mode, and G-ænial Bond in self-etch mode. Specimens were tested either immediately or after artificial aging (thermocycling or water storage). μTBS values were analyzed statistically, and the resin–dentin interfaces were examined using FE-SEM (Field-emission scanning electron microscopy). Results: Results showed that both aging and adhesive mode significantly affected the μTBS (p < 0.0001). Immediately after bonding, etch-and-rinse modes produced significantly higher μTBS than the self-etch modes (p < 0.0001). Artificial aging reduced bond strength by approximately 30–50%; however, the μTBS of Hi-Bond Universal decreased less than that of Single Bond 2 after water storage. FE-SEM analysis also revealed detachment of the hybrid layer in most adhesives following aging; however, Hi-Bond Universal in the etch-and-rinse mode maintained a relatively intact adhesive layer after water storage. Conclusion: Etch-and-rinse application of MBG-containing adhesive may enhance the long-term durability of adhesive restorations. Full article

This study investigated the toxicity of ten polymer materials intended for the development of invasive neural interfaces improving the treatment of neurological diseases. Most of the materials for neural implants can cause traumatization of the surrounding tissue, inflammation, and foreign body reaction. In this study, in vitro and in vivo toxicity assessment was performed for nylon 618 (NY), polycaprolactone (PCL), polyethylene glycol diacrylate (PEGDA), polydimethylsiloxane (PDMS), polyethylene terephthalate (PET), polylactide (PLA), thermoplastic polyurethane (TPU), polypropylene (PP), polyethylene terephthalate glycol (PET-G), and polyimide (PI). The biocompatibility of these ten materials was assessed based on cell adhesion, growth and cytotoxicity on neural (PC-12) and fibroblast (NRK-49F) cultures. Furthermore, brain tissue responses to the implanted phantom scaffolds were analyzed in rats. According to these measurements, PI showed the highest compatibility for both cell types. PEGDA exhibited cytotoxic effects, low cell adhesion and the strongest foreign body reaction, including fibrosis and multinucleated cell formation. The other polymers showed lower pathological responses which makes them potentially usable for neural interfacing. We conclude that PEGDA appears to be unsuitable for long-term use due to adverse tissue and cellular reactions, whereas PI, PLA, PDMS and TPU hold promise as materials for safe and effective neural interface applications. Full article

Osteochondral repair remains challenging due to cartilage’s limited self-healing capacity and the structural complexity of the osteochondral interface, particularly the hypertrophic layer anchoring cartilage to bone. We fabricated melt electrowritten (MEW) poly(L-lactic acid) (PLLA) scaffolds incorporating 1%, 5%, and 10% hydroxyapatite (HAp) to provide a precise fiber architecture (~200 μm pores) and bone-mimetic biochemical cues. Human nasal chondrocytes (hNCs), currently in clinical trials for knee cartilage repair, were selected for their phenotypic plasticity and established safety profile, facilitating translational potential. HAp–PLLA scaffolds, especially at higher HAp contents, enhanced hNC adhesion, proliferation, mineralization, and maintenance of cartilage-specific ECM compared to PLLA alone. This work demonstrates the first high-HAp MEW-printed PLLA scaffold for osteochondral repair, integrating architectural precision with bioactivity in a clinically relevant cell–material system. Full article

Latent stripping has become increasingly apparent in asphalt pavements, particularly in highway rehabilitation and international construction projects supported by Official Development Assistance (ODA) from the Government of Japan. Stripping accelerates structural deterioration, making countermeasures essential. However, in ODA projects, securing high-quality aggregates or evaluating local materials is often difficult due to environmental and budgetary constraints. This study focused on Surface Free Energy (SFE) as a small-sample evaluation method and developed ten types of styrene–butadiene–styrene (SBS) polymers to enhance interfacial adhesion by targeting aggregate surface functional groups. The SFE of each Polymer-Modified Bitumen (PMB) and thirteen aggregates was measured, and the work of adhesion and moisture sensitivity index (MSI) were calculated for all combinations. Twenty-one Hot-Mix Asphalts (HMA) were then prepared and evaluated using the Hamburg Wheel Tracking Test (HWTT) based on load cycles to stripping initiation (LC_SN) and to 12.5 mm rut depth (LC_ST). The developed PMBs showed a higher work of adhesion, a lower MSI, and substantially increased LC_SN and LC_ST values. Strong negative correlations were observed between MSI and both HWTT indicators, confirming the utility of SFE-based MSI for material screening. This study demonstrates that interface-targeted PMBs can improve stripping resistance, thereby promoting the use of lower-quality aggregates in durable pavements. Full article

Fe-Cr-Nb-C wear-resistant alloy coatings were successfully fabricated on high-carbon forged steel via coaxial powder feeding laser cladding. The evolution of microstructure and wear resistance with varying Nb content was systematically investigated. The results indicate that appropriate NbC addition markedly modifies the distribution of grain and boundary carbides. As Nb content increases from 2.5 wt% to 3.5 wt%, nanoscale rod-like NbC precipitates form uniformly along boundaries, effectively suppressing the formation of brittle Cr₂₃C₆ precipitation. Semi-coherent NbC/matrix interfaces and NbC-induced grain refinement reduce adhesive/abrasive wear, thereby improving hardness and wear resistance. At 4.5 wt% Nb, discrete micron-sized NbC particles form within the grains, yielding optimal performance. However, excessive Nb (≥5.5 wt%) causes NbC agglomeration, inducing stress concentrations and large spallation pits that deteriorate wear resistance. This work highlights NbC morphology as a key factor for tailoring coating properties. Full article