Search Results (184)

In this study, AA7068 aluminum matrix composites reinforced with TiB₂/TiC were fabricated via mechanical alloying and microwave sintering to investigate the influence of reinforcement content and sintering temperature on microstructure, mechanical properties, and dry sliding wear. Mechanical alloying refined powders, reducing D₅₀ from 51.5 µm (AA) to 22.5 µm (AC9) and enhancing dispersion and retention of TiB₂/TiC particles. XRD confirmed α-Al as the dominant matrix phase, preserved TiB₂ and TiC phases, and limited MgAl₂O₄/ZnAl₂O₄ spinel formation. Crystallite refinement and increased lattice microstrain were observed with the addition of reinforcement. Microhardness increased with reinforcement content and sintering temperature, reaching 122.2 HV_0.05 in AC9-2. At the same time, the highest compressive strength was observed in AC6-2 (431.05 MPa), indicating that optimal load-bearing depends on densification and interfacial integrity rather than hardness alone. AC9-2 exhibited the best wear resistance, with a cumulative specific wear rate of 2.723 × 10⁻⁴ mm³/Nm over 1000 m. SEM-EDS analysis revealed oxide-rich tribolayers, mechanically mixed layers, TiB₂/TiC fragments, and Fe-rich third-body debris, indicating wear is predominantly hardness-controlled but strongly influenced by microstructural factors. Overall, TiB₂/TiC hybrid reinforcement improves AA7068 wear resistance through combined hard-particle load-bearing, reduced penetration, tribolayer stability, and third-body effects, offering insight for high-performance hybrid aluminum composites. Full article

The outcomes of a standard geochemical, geophysical and petrographical approach to exploration at Lead Trial, a small prospect in central Scotland, have been compared to the interpretation of a parallel gold compositional study describing 703 gold particles from local in situ and alluvial occurrences. Standard exploration approaches identified a 4.5 km² zone hosting an array of numerous auriferous (to 17 g/t Au), vuggy, brecciated quartz-galena ± sphalerite veins culminating in the identification of a drill target. The gold study identified three gold compositional types: two 23–32 wt.% Ag alloys with a Zn-Pb-Cu mineral inclusion assemblage differentiated by sphalerite abundance, and a 5–16 wt.% Ag alloy with a Mo-Bi-Pb-Cu-Fe inclusion signature, yet to be correlated with either float or outcrop. Spatial distribution of the gold types indicates lateral variation and probably vertical variation within a single magmatic hydrothermal system. Integration of gold particle studies with early stages of exploration offers rapid insights into the nature and distribution of mineralization when very limited information is available and is mutually supportive of standard exploration approaches. Full article

Dissimilar 7075-T6 and 6061-T6 aluminum alloy joints were fabricated using pulsed metal inert gas (P-MIG) welding with ER5356 filler wire. The effects of welding current (224 A, 234 A, and 244 A) on macro-morphology, microstructure, mechanical properties, and corrosion behavior were systematically investigated. As welding current increased, the top and bottom reinforcements first increased and then decreased, reaching maximum values at 234 A, while the front weld width exhibited the opposite trend. The weld zone consisted of equiaxed and dendritic grains, with partial remelting of AlFeMnSi intermetallic compounds observed in the heat-affected zones. The microhardness and tensile strength of the joints followed a similar trend of first decreasing and then increasing with welding current, achieving a maximum tensile strength of 203.9 MPa at 244 A, corresponding to 89.5% of the 6061-T6 base metal strength. Corrosion resistance varied across regions depending on the evaluation method. In intergranular corrosion tests, the 7075-HAZ showed the highest susceptibility due to grain boundary segregation of Mg and Zn. In electrochemical tests, the WZ exhibited the poorest corrosion resistance. For the 7075-HAZ, optimal corrosion resistance was achieved at 234 A, attributed to a stable passive film and uniform precipitate distribution. These findings provide valuable guidance for optimizing P-MIG welding parameters for dissimilar 7075/6061 aluminum alloy joints. Full article

This study investigates the optimization of selected process parameters in the rotary friction welding (RFW) process of CuSi₃Fe₂Zn₃ silicon bronze alloys using Response Surface Methodology (RSM) with tensile strength as the primary response. The effects of rotation speed, friction time and friction pressure were evaluated, and the steepest ascent method was applied to determine the best parameters. The results indicated that rotation speed and friction time were the most influential parameters for enhancing tensile strength. A maximum tensile of 424 MPa was achieved under conditions of 3300 rpm, friction time of 25 s, friction pressure of 0.5 MPa, forging time of 16 s, and forging pressure of 8 MPa. However, confirmation experiments exhibited noticeable variability, indicating limitations in process repeatability. Tensile properties, hardness evaluation, microstructural characterization, and thermographic analysis were conducted to assess the quality of the welded joints. Microstructural analysis revealed recrystallized equiaxed grains in the welding center zone, consistent with severe plastic deformation, while microcracks and microvoids were observed and likely contributed for failure during tensile testing. Despite grain refinement, a reduction in microhardness was detected, suggesting the influence of thermal softening mechanisms. Thermographic analysis indicated that the average temperature at the welding center zone reached 564 °C. In conclusion, RSM proved to be a useful tool for identifying trends and guiding process optimization. The results highlight the importance of process stability and control in achieving consistent performance in RFW of copper-based alloys. Full article

This study investigates the 55%Al-Zn-Si coating system. Using microstructural characterization and thermodynamic simulation, we systematically analyzed its microstructure formation, solidification behavior, and the regulatory effects of Cr, Nb, and V micro-alloying elements. The results show that the typical coating consists of a primary α-Al dendritic skeleton and an interdendritic Zn-rich eutectic phase, exhibiting a characteristic spangle morphology. The addition of Si is crucial. By participating in the formation of a Fe-Al-Si ternary compound layer, it effectively suppresses the intense reaction at the Fe/Al interface, providing essential conditions for the sufficient growth of the outer Al-rich dendrites and the formation of a continuous transition layer. Thermodynamic analysis further clarifies that the coating solidification follows three distinct stages: precipitation of the primary α-Al phase, an Al-Si binary eutectic reaction, and a final Al-Zn-Si ternary eutectic transformation. Regarding micro-alloying, this study reveals the specific roles of different elements: Cr significantly refines the transition layer structure, promoting its transformation from coarse lamellae into a fine and uniform morphology; V tends to combine with Al to form high-melting-point enriched regions, inhibiting the growth of Fe-Al intermetallics and reducing the thickness of the brittle transition layer by approximately 50%; conversely, the addition of Nb disrupts the normal solidification sequence, inducing abnormal segregation of Al-rich and Si-rich phases, which compromises the homogeneity and integrity of the coating structure. Through an in-depth analysis of the fundamental solidification mechanism and micro-alloying effects, this research provides an important theoretical basis for optimizing the microstructure of hot-dip Al-Zn sheets via precise composition design and micro-alloying strategies. Full article

Biodegradable metals represent a paradigm shift in orthopedic fixation by providing temporary mechanical support synchronized with bone healing while eliminating long-term complications associated with permanent implants. Conventional bioinert alloys, including stainless steels, Ti-based alloys, and Co-Cr alloys, exhibit high elastic moduli that induce stress shielding and often require secondary removal surgeries. In response, resorbable metallic systems based on Mg, Zn, and Fe have emerged as promising alternatives. Among these, Fe-Mn-C alloys stand out for load-bearing applications due to their exceptional strength-ductility balance governed by twinning-induced plasticity mechanisms, tunable degradation behavior, and intrinsic magnetic resonance imaging compatibility through austenitic phase stabilization. Focusing on Fe-Mn-C alloys, this review critically examines the metallurgical design principles underlying stacking fault energy optimization, phase stability, and Mn-controlled electrochemical behavior. Processing innovations, such as additive manufacturing, are discussed as tools to architecture porosity, refine microstructure, and accelerate degradation by graded designs while preserving mechanical structural support during healing. Hybrid metallic-bioactive systems, surface functionalization strategies, and functionally graded porous architectures were evaluated as advanced approaches to enhance osteointegration and modulate degradability. Despite these advances, significant barriers remain for clinical translation. Persistent discrepancies between in vitro and in vivo degradation rates, often attributed to biological encapsulation and degradation product accumulation, complicate lifetime prediction. Localized corrosion at microstructural heterogeneities such as twin boundaries and phase interfaces can undermine structural reliability under load-bearing conditions. Moreover, predictive multi-physics modeling frameworks capable of coupling electrochemical kinetics, mechanical loading, microstructural evolution, and bone remodeling remain underdeveloped, limiting reliable safety-margin estimation. Regulatory progress is further hindered by the absence of standardized testing protocols specifically tailored to Fe-based biodegradable alloys, including harmonized degradation rate windows, validated corrosion-mechanics coupling methodologies, and clinically defined Mn ion release thresholds. This review aims to discuss whether Fe-based alloys, especially Fe-Mn-C alloys, can transition from promising laboratory materials to clinically viable next-generation orthopedic implants capable of delivering patient-specific, mechanically compatible, and biologically synchronized temporary fixation. Full article

Machine learning interatomic potentials (MLIPs) are typically developed for globally ordered homogeneous systems (GOHomS), which exhibit only minor local deviations from equilibrium configurations. Consequently, most existing MLIPs trained on GOHomS often perform inadequately when applied to locally ordered heterogeneous systems (LOHetS), e.g., substitutional alloying elements in multicomponent alloys. To describe doping alloy systems, we develop a fine-tuned MLIP based on the MACE foundation model, specifically tailored for Mo-based dilute alloys containing one or two out of 20 substitutional elements: Cr, Fe, Mn, Nb, Re, Ta, Ti, V, W, Y, Zr, Al, Zn, Cu, Ag, Au, Hg, Co, Ni, and Hf. The model is built on more than 7000 equilibrium and non-equilibrium structures derived from first-principles density functional theory (DFT) calculations. The optimized large-scale fine-tuned model attains state-of-the-art accuracy, with a mean absolute error (MAE) and root-mean-square error (RMSE) of 2.27 meV/atom and 3.79 meV/atom for energy predictions, and 13.83 meV/Å and 24.26 meV/Å for force predictions, respectively. Systematic evaluation under different data-splitting protocols shows that unknown element extrapolation remains challenging under strict dopant hold-out, whereas substantially improved accuracy can be achieved in partial-exposure transfer settings. The fine-tuned models reduce the MAE by approximately 7–10 times compared to models trained from scratch, and by 10–20 times relative to zero-shot foundation models. This performance gain remains consistent across varying dataset sizes (equilibrium vs. non-equilibrium structures) and model scales. Our work illustrates the efficacy of transfer learning from globally ordered homogeneous systems to locally ordered heterogeneous multicomponent alloy environments. However, direct transfer to entirely unknown elements remains challenging, especially when proxy embeddings are employed without fine-tuning. Thus, to achieve high accuracy without incurring additional cost, it is essential to include unknown elements in the training dataset while minimizing the number of configurations containing known elements. Moreover, the current findings are primarily validated for dilute Mo-based alloy systems. Extending this approach to more compositionally complex alloy spaces may necessitate additional data and further fine-tuning. Full article

Copper (Cu) smelting slags are considered secondary reserves of technology metals (TMs) and base metals (BMs), which are crucial for the transition to renewable energy and mechatronic applications. In this study, thermochemical and experimental analyses were conducted to investigate the pyrometallurgical extraction of TMs and BMs from Cu smelting slag. FactSage thermochemical simulations and smelting experiments were carried out at temperatures from 1300 to 1600 °C and with carbon (reductant) additions of 2% to 10% relative to the mass of the feed slag. The results showed that during smelting, gallium (Ga), germanium (Ge), cobalt (Co), and copper (Cu) deported into the iron-based alloy product. Zinc (Zn) and lead (Pb) oxidised to ZnO and PbO, respectively, which were subsequently collected as fumes. The produced alloy mass was more sensitive to carbon addition than to smelting temperature variation. The TM and BM contents in the alloy decreased with increasing carbon addition in the feed; this was attributed to dilution by Fe, Si, and C from the increasing reduction of iron and silicon oxides in the feed slag and dissolution of C in the alloy. High recovery degrees of TMs and BMs in the alloy stream—over 90% for Co and Cu, over 50% for Ga, and over 70% for Ge—were achieved when smelting at 1500 °C with 4% carbon addition. The final alloy comprised 70.5% Fe, 6.6% Co, 23.6% Cu, 0.11% Ga, and 0.13% Ge. The fumes primarily comprised ZnO and, to a lesser extent, PbO, with recovery degrees over 90% for Zn and Pb. These alloy and fume products would be processed following conventional hydrometallurgical separation and purification processes to produce high-purity metals. The pyrometallurgical extraction of TMs and BMs presents an opportunity for the valorisation of Cu smelting slag dumps, especially in Southern Africa, aiming to attain zero-waste industrial processes. Full article

The antimicrobial activity of multicomponent, magnetron-sputtered glass coatings was evaluated against phytopathogenic fungi (Botrytis cinerea, Fusarium oxysporum, Cladosporium fulvum, Alternaria solani) and the chromista Phytophthora infestans, with Aspergillus fumigatus included as a model opportunistic pathogen. Fourteen Cu-based multicomponent coatings were deposited on glass using multi-alloy targets composed of Sn, Zn, Al, Ni, Fe, Ti, Mn, Nb, or Co in two high-transmittance variants (≥85% and ≥88%). Antimicrobial activity was assessed in two assays: (A) spore survival after 24–72 h contact, and (B) hyphal growth over 7 days following coating exposure under light and dark conditions. Spore viability decreased after incubation on high-Cu coatings, which showed inhibition for most strains, particularly B. cinerea, F. oxysporum, and P. infestans. The effects on spore germination were independent of the direct transmittance value of the coated glass. Hyphal growth was generally less affected by a high Cu content for most strains. Hyphal growth of F. oxysporum, C. fulvum, A. solani and B. cinerea was reduced by up to 30% on selected multicomponent coatings. For most strains, hyphal growth showed no inhibition after light incubation on coatings. However, light-dependent effects were observed for A. solani, A. fumigatus and P. infestans, while B. cinerea and C. fulvum showed reduced sensitivity during the first two days. High-Cu coatings were most effective at inhibiting spore germination, whereas hyphal growth on multicomponent coatings may respond to different ions. Therefore, high-Cu, two-component coatings may be recommended for practical greenhouse applications. Full article

Mg-Zn-Ca bulk metallic glasses (BMGs) have attracted significant attention in the field of biodegradable metallic biomaterials due to their desirable in vivo degradability and high strength. However, their relatively high brittleness limits further practical applications. In this work, porous Fe skeleton-reinforced Mg-Zn-Ca bulk metallic glass composites (BMGCs) were fabricated by pressure infiltration using porous Fe skeleton as the toughening phase and Mg₆₆Zn₃₀Ca₃Sr₁ alloy as the matrix. It was found that electroless copper plating improved the interfacial wettability between molten Mg and Fe, as well as the infiltration-forming capability of the BMGCs. Quasi-static compression tests showed that the BMGC exhibited a compressive strength of 500 MPa, a plastic strain of 0.2%, and a yield strength of 420 MPa, representing a significant improvement over the matrix BMG alloy. The fracture surface displayed a vein-like pattern, indicating a noticeable transition from brittle to ductile fracture behavior. Thus, the porous Fe skeleton-reinforced Mg-Zn-Ca BMGC shows promise as a potential biodegradable biomedical material. Moreover, the preparation route presented here offers a new perspective for developing degradable Mg-Zn-Ca-based BMGCs. Full article

Antibacterial thin-film coatings are of increasing interest for enhancing hygiene in controlled environments such as commercial greenhouses. Phytopathogens including Pseudomonas syringae, and human pathogens such as Escherichia coli, Micrococcus luteus, and Staphylococcus aureus, frequently contaminate greenhouse environments. The present study aimed to develop and evaluate multifunctional magnetron-sputtered glass coatings with strong antimicrobial performance, deposited by physical vapor deposition to achieve precise control of film composition and uniform coverage of large substrates (≥0.25 m²), ensuring industrial-scale applicability. Thin films were fabricated by magnetron sputtering using multi-alloy targets composed of Cu, Sn, Zn, Al, Ni, Fe, Ti, Mn, Nb, or Co. Fourteen distinct coating compositions were characterized using high-resolution transmission electron microscopy, scanning transmission electron microscopy, and energy-dispersive X-ray spectroscopy. Antibacterial performance was evaluated against the following strains: E. coli (PCM 2560), M. luteus (PCM 525), S. aureus (PCM 2602), and P. syringae pv. tomato (IOR2146). Coatings prepared from 90%Cu-10%Sn, 90%Cu-10%Zn, and 80%Cu-20%Ti targets exhibited one of the highest antibacterial efficiencies. These coatings also showed strong mechanical durability and corrosion resistance. Our results indicate that coatings obtained from Cu-based multi-alloy targets by magnetron sputtering are promising candidates for use as durable, antimicrobial inner glass surfaces in future greenhouse applications. Full article

Net-shaped casting processes in the automotive industry have proved to be difficult to simulate due to the complexities of the interactions amongst thermal, fluid, and solute transport regimes in the solidifying domain, along with the interface. The existing casting simulation software lacks the necessary real-time estimation of thermophysical properties (thermal diffusivity and thermal conductivity) and the interfacial heat-transfer coefficient (IHTC) to evaluate the thermal resistances in a casting process and solve the temperature in the solidifying domain. To address these shortcomings, an axial directional solidification experiment setup was developed to map the thermal data as the melt solidifies unidirectionally from the chill surface under unsteady-state conditions. A Dilute Eutectic Cast Aluminum (DECA) alloy, Al-5Zn-1Mg-1.2Fe-0.07Ti, Eutectic Cast Aluminum (ECA) alloys (A365 and A383), and pure Al (P0303) were used to demonstrate the validity of the experiments to evaluate the thermal diffusivity (α) of both the solid and liquid phases of the solidifying metal using an inverse heat-transfer analysis (IHTA). The thermal diffusivity varied from 0.2 to 1.9 cm²/s while the IHTC changed from 9500 to 200 W/m²K for different alloys in the solid and liquid phases. The heat flux was estimated from the chill side with transient temperature distributions estimated from IHTA for either side of the mold–metal interface as an input to compute the interfacial heat-transfer coefficient (IHTC). The results demonstrate the reliability of the axial solidification experiment apparatus in accurately providing input to the casting simulation software and aid in reproducing casting numerical simulation models efficiently. Full article

In physiological environments, several metallic alloys, including titanium, stainless steel, cobalt–chromium, and emerging biodegradable systems such as magnesium (Mg), zinc (Zn), and iron (Fe), offer mechanical properties and biocompatibility suitable for load-bearing implants. With the rapid advancement of 3D printing technologies, these alloys can now be fabricated into patient-specific, complex geometries that enhance both structural performance and functional integration. Beyond serving as structural supports, 3D-printed alloys are increasingly engineered as localized drug-delivery platforms to release anti-inflammatory, antibacterial, anticancer, and osteogenic agents at the implant–tissue interface, addressing the dual clinical needs of site-specific therapy and mechanical stabilization. Nevertheless, this field remains underexplored because studies differ widely in alloy chemistry, surface topography, porosity, coating strategy, drug-loading methods, and release profiles, as well as in how material degradation or passivation interacts with pharmacokinetics. For the first time, this review consolidates drug-loading and elution strategies across 3D-printed alloy platforms, compares therapeutic categories in relation to alloy and coating types, and critically evaluates how the surface microstructure or alloy geometry influences release behavior. Full article

This research focuses on the investigation of microstructure, deformation, and superplastic behavior in wide range of strain rates of novel crossover Al-Zn-Mg-Cu alloy with Y/Er. The precipitation and superplastic behavior of the Al-Zn-Mg-Cu-Zr-Cr-Ti with Er/Y and Fe/Si impurities alloys have been studied. The microstructure of the alloys with nano-sized precipitates and micron-sized particles allows obtaining a micrograin stable microstructure. The spherical D0₂₃-Al₃(Er,Zr) precipitates with a diameter of about 20 nm and rod-like crystalline and qusicrystalline E (Al₁₈Mg₃Cr₂) precipitates with a thickness of about 20 nm and length of about 150–200 nm were identified by transmission electron microscopy. The superplastic deformation behaviors were investigated under different temperatures of 460–520 °C and different strain rates of 3 × 10⁻⁴ to 3 × 10⁻³ s⁻¹. The microstructure observation shows that uniform and equiaxed grains can be obtained by dynamic recrystallization before superplastic deformation. The alloy with Y exhibits inferior superplastic properties, while the alloy with Er has an elongation of more than 350% at a rate of 1 × 10⁻³ s⁻¹ and a temperature of 510 °C. Full article

By tuning the extrusion parameters, the corrosion performances of as-extruded Mg-0.5Zn(-0.2X) alloys (X: Ca/Sr/Ag/In/Cu, denoted as Z05, Z0502-Ca, Z0502-Sr, Z0502-Ag, Z0502-In and Z0502-Cu, respectively) with similar grain sizes were investigated and compared with their as-cast counterparts. The formed Fe-Si precipitates after hot processing significantly accelerate the corrosion rates of Z05, Z0502-Ag and Z0502-In, whereas the driving force from the Fe-encapsulated MgCaSi(Fe) and MgSrSi(Fe) precipitates are not as strong in Z0502-Ca and Z0502-Sr. Impacts from Fe impurity in Z0502-Cu are masked in the fast corrosion due to the noble Mg2Cu intermetallics. Fe precipitation during hot processing is critical for micro-alloyed systems, as the changes in intermetallic/impurity distributions impact the corrosion performances profoundly. The enthalpy of formation and the potential difference are the key factors that influence the distribution of precipitate during hot processing. Full article