Search Results (39)

Se-doped CdTe thin films were grown employing a simple two-electrode electrochemical deposition method using glass/tin-doped indium oxide (glass/ITO). Cadmium acetate dihydrate [Cd (CH₃CO₂)₂. 2H₂O], selenium dioxide (SeO₂), and tellurium dioxide (TeO₂) were used as precursors. Instruments including X-ray diffraction for structural investigation, UV-Vis spectrophotometry for optical properties, and scanning probe microscopy for morphological properties were employed to investigate the physico-chemical characteristics of the resulting Se-doped CdTe thin-film. The films are polycrystalline with a cubic phase, according to X-ray diffraction (XRD) data. More ions are deposited on the substrate, which makes the material more crystalline and intensifies the characteristic peaks that are seen. It is observed from the acquired optical characterization that the film’s bandgap is greatly influenced by the deposition time. The bandgap dropped from 1.92 to 1.62 as the deposition period increased from 25 to 45 min, making the film more transparent and absorbing less light at shorter deposition durations. Images from scanning electron microscopy (SEM) show that the surface morphology is homogenous with closely packed grains and that the grain forms become less noticeable as the deposition time increases. This work is novel in that it investigates the influence of the deposition time on the structural, optical, and morphological properties of Se-doped CdTe thin films deposited using a cost-effective, simplified two-electrode electrochemical method—a fabrication route that remains largely unexplored for this material system. Full article

The interaction between selenomethionine (SeMet) and n-3 polyunsaturated fatty acids (n-3 PUFA) in producing n-3 PUFA-enriched pork remains unknown. This study investigates the effect of different n-3 PUFA sources (linseed oil vs. fish oil) and SeMet supplementation on meat quality and fatty acid composition in finishing pigs. Key findings demonstrate that dietary supplementation with 0.3 mg/kg SeMet significantly enhances the L*_24h value (lightness) of the longissimus thoracis et lumborum (LTL) tissue compared to 3% linseed oil or fish oil treatments alone (p < 0.05). Pork flavor improvement is further supported by increased serine content (p < 0.05) and a notable tendency toward elevated total sweet amino acids (Thr + Ser + Gly + Ala + Pro) in LTL tissue (p = 0.077). Compared with 3% sunflower oil (control group), 3% linseed oil or fish oil significantly enhances n-3 PUFA content while reducing the n-6/n-3 ratio in both LTL and subcutaneous adipose tissue (p < 0.05). The synergistic interaction between SeMet and oil (linseed oil or fish oil) is observed, increasing α-linolenic acid (ALA; C18:3n-3), eicosatrienoic acid (C20:3n-3), and total n-3 PUFA deposition in subcutaneous fat tissue (p < 0.05). SeMet increases the activities of total superoxide dismutase (T-SOD) and catalase (CAT). Meanwhile, the SeMet-fish oil combination decreases lipids oxidation compared to individual treatments (p < 0.05). Collectively, 3% linseed oil or fish oil effectively enhances unsaturated fatty acid profiles, while concurrent SeMet addition may synergistically enhance certain nutritional attributes (improved oxidative stability) and sensory scores (enhanced L_{24 h}* value and flavor precursors). We, therefore, recommend adding 0.3 mg/kg SeMet to the n-3 PUFA-enriched pork production process. Full article

Non-noble metal electrocatalysts for the hydrogen oxidation reaction (HOR) that are both highly active and low-cost are essential for the widespread use of fuel cells. Herein, a simple two-step method for creating an in-plane heterostructure of Ni₃N/MoSe₂ loaded on N-doped reduced graphene oxide (Ni₃N/MoSe₂@N-rGO) as an effective electrocatalyst for the HOR is described. The process involves hydrothermal treatment of the Ni and Mo precursors with N-doped reduced graphene oxide, followed by the annealing with urea. The Ni₃N/MoSe₂@N-rGO catalyst exhibits high activities for the HOR, with current densities of 2.15 and 3.06 mA cm⁻² at 0.5 V vs. the reversible hydrogen electrode (RHE) in H₂-saturated 0.1 M KOH and 0.1 M HClO₄ electrolytes, respectively, which is comparable to a commercial 20% Pt/C catalyst under similar experimental conditions. Furthermore, the catalyst demonstrates excellent durability, maintaining its performance during accelerated degradation tests for 5000 cycles. This work offers a practical framework for the designing and preparing of non-precious metal electrocatalysts for the HOR in fuel cells. Full article

Wildfires significantly influence the environmental distribution of various elements through their fire-induced input and mobilization, yet little is known about their effects on the forest floor in Siberian forests. The present study evaluated the effects of spring wildfires of various severities on the levels of major and minor (Ca, Al, Fe, S, Mg, K, Na, Mn, P, Ti, Ba, and Sr) trace and ultra-trace (B, Co, Cr, Cu, Ni, Se, V, Zn, Pb, As, La, Sn, Sc, Sb, Be, Bi, Hg, Li, Mo, and Cd) elements in the forest floors of Siberian forests. The forest floor (Oi layer) samples were collected immediately following wildfires in Scots pine (Pinus sylvestris L.), larch (Larix sibirica Ledeb.), spruce (Picea obovata Ledeb.), and birch (Betula pendula Roth) forests. Total concentrations of elements were determined using inductively coupled plasma–optical emission spectroscopy. All fires resulted in a decrease in organic matter content and an increase in mineral material content and pH values in the forest floor. The concentrations of most elements studied in a burned layer of forest floor were statistically significantly higher than in unburned precursors. Sb and Sn showed no statistically significant changes. The forest floor in the birch forest showed a higher increase in mineral material content after the fire and higher levels of most elements studied than the burned coniferous forest floors. Ca was a predominant element in both unburned and burned samples in all forests studied. Our study highlighted the role of wildfires in Siberia in enhancing the levels of geochemical elements in forest floor and the effect of forest type and fire severity on ash characteristics. The increased concentrations of elements represent a potential source of surface water contamination with toxic and eutrophying elements if wildfire ash is transported with overland flow. Full article

The synthesis of methanol from CO₂ hydrogenation is an effective measure to deal with global climate change and an important route for the chemical fixation of CO₂. In this work, carbon-confined MoSe₂ (MoSe₂@C) catalysts were prepared by in situ pyrolysis using glucose as a carbon source. The physico-chemical properties and catalytic performance of CO₂ hydrogenation to yield methanol were compared with MoSe₂ and MoSe₂/C. The results of the structure characterization showed MoSe₂ displayed few layers and a small particle size. Owing to the synergistic effect of the Mo₂C-MoSe₂ heterojunction and in situ carbon doping, MoSe₂@C with a suitable C/Mo mole ratio in the precursor showed excellent catalytic performance in the synthesis of methanol from CO₂ hydrogenation. Under the optimal catalyst MoSe₂@C-55, the selectivity of methanol reached 93.7% at a 9.7% conversion of CO₂ under optimized reaction conditions, and its catalytic performance was maintained without deactivation during a continuous reaction of 100 h. In situ diffuse infrared Fourier transform spectroscopy studies suggested that formate and CO were the key intermediates in CO₂ hydrogenation to methanol. Full article

Transition metal dichalcogenides (TMDs), particularly monolayer TMDs with direct bandgap properties, are key to advancing optoelectronic device technology. WSe₂ stands out due to its adjustable carrier transport, making it a prime candidate for optoelectronic applications. This study explores monolayer WSe₂ synthesis via H₂-assisted CVD, focusing on how carrier gas flow rate affects WSe₂ quality. A comprehensive characterization of monolayer WSe₂ was conducted using OM (optical microscope), Raman spectroscopy, PL spectroscopy, AFM, SEM, XPS, HRTEM, and XRD. It was found that H₂ incorporation and flow rate critically influence WSe₂’s growth and structural integrity, with low flow rates favoring precursor concentration for product formation and high rates causing disintegration of existing structures. This research accentuates the significance of fine-tuning the carrier gas flow rate for optimizing monolayer WSe₂ synthesis, offering insights for fabricating monolayer TMDs like WS₂, MoSe₂, and MoS₂, and facilitating their broader integration into optoelectronic devices. Full article

In this research, TiO₂ nanotubes (NTs) were produced by electrochemical anodization of a Ti substrate where different NH₄F wt.% in the electrolyte was added. NTs with diameter of 65–90 nm and 3.3–4.9 µm length were obtained and sensitized with binary cadmium chalcogenides nanoparticles, CdS and CdSe, by successive ionic layer adsorption and reaction method (SILAR). Additionally, both anions S and Se were deposited onto Cd, labeled as CdSSe and CdSeS, to evaluate the effect of the deposition order of the anion from the precursor solution to form cadmium chalcogenides. The structural, optical, and electrochemical performance were analyzed through the SEM, XRD, XPS, UV-VIS, lineal voltammetry and chronoamperometry characterizations. The increase of NH₄F wt.% from 1.5% to 4.5% produced a decrement of the diameter and length attributed to the fluoride ions concentration causing solubility of the NTs. XRD confirmed the TiO₂ anatase and hexagonal CdS structures. From the EDS and XPS results, the presence of small amount of Se in the sensitized samples demonstrated the doping effect of Se instead of forming ternary semiconductor. With the sensitization of the TiO₂ NTs with the nanoparticles, an improved hydrogen generation was observed (reaching 1.068 mL h⁻¹ cm⁻²) in the sample with CdSSe. The improvement was associated to a synergetic effect in the light absorption and higher cadmium chalcogenide amount deposited when sulfur ions were deposited before selenium. Full article

Selenium nanoparticles (Se NPs) have a number of unique properties that determine the use of the resulting nanomaterials in various fields. The focus of this paper is the stabilization of Se NPs with cetyltrimethylammonium chloride (CTAC). Se NPs were obtained by chemical reduction in an aqueous medium. The influence of the concentration of precursors and synthesis conditions on the size of Se NPs and the process of micelle formation was established. Transmission electron microscopy was used to study the morphology of Se NPs. The influence of the pH of the medium and the concentration of ions in the sol on the stability of Se micelles was studied. According to the results of this study, the concentration of positively charged ions has a greater effect on the particle size in the positive Se NPs sol than in the negative Se NPs sol. The potential antibacterial and fungicidal properties of the samples were studied on Escherichia coli, Micrococcus luteus and Mucor. Concentrations of Se NPs stabilized with CTAC with potential bactericidal and fungicidal effects were discovered. Considering the revealed potential antimicrobial activity, the synthesized Se NPs-CTAC molecular complex can be further studied and applied in the development of veterinary drugs, pharmaceuticals, and cosmetics. Full article

Luminescent diimine-Pt(IV) complexes [Pt(N^N)(Me)₂(PhSe)₂], (N^N = 2,2′-bipyridine (bpy, 1b), 1,10-phenanthroline (phen, 2b), and 4,4′-dimethyl-2,2′-bipyridine (Me₂bpy, 3b), PhSe⁻ = phenyl selenide were prepared and identified using multinuclear (¹H, ¹³C{¹H} and ⁷⁷Se{¹H}) NMR spectroscopy. The PhSe⁻ ligands were introduced through oxidative addition of diphenyl diselenide to the non-luminescent Pt(II) precursors [Pt(N^N)(Me)₂], N^N = (bpy, 1a), (phen, 2a), (Me₂bpy, 3a), to give the luminescent Pt(IV) complexes 1b–3b. The UV-vis absorption spectra of 1b–3b are characterised by intense bands in the range 240–330 nm. We assigned them to transitions of essentially π−π* character with small metal and PhSe⁻ ligand contributions with the help of TD-DFT (time-dependent density functional theory) calculations. The weak long-wavelength bands in the range 350–475 nm are of mixed ligand-to-metal charge transfer (L’MCT) (n_(Se)→d_(Pt)/intra-ligand charge transfer (IL’CT) (n_(Se)→π*_(Ph) or π_(Ph)→π*_(Ph))/ligand-to-ligand’ charge transfer (LL’CT) (L = N^N, L’ = PhSe⁻, M = Pt and n = lone pair) character. The Pt(IV) complexes showed broad emission bands in the solid state at 298 and 77 K, peaking at 560–595 nm with a blue shift upon cooling. Structured emission bands were obtained in the range 450–600 nm, with the maxima depending on the N^N ligands and the solvent polarity (CH₂Cl₂ vs. dimethyl sulfoxide (DMSO) and aqueous tris(hydroxymethyl)aminomethane hydrochloride (tris-HCl) buffer). The emissions originate from essentially ligand-centred triplet states (³LC) with mixed IL’CT/L’MCT contributions as concluded from the DFT calculation. Such dominating PhSe contributions to the emissive states are unprecedented in the world of luminescent diimine-Pt(IV) complexes. Full article

This work describes the spray pyrolysis deposition of PbSe films, using as-prepared PbSe colloids as the starting solution. The PbSe colloids were prepared by using the alkahest approach, where Pb and Se precursors were made to react with the following green polyols: glycerin, ethylene glycol, and propylene glycol, to subsequently spray them onto glass substrates. The results of the characterization indicated that amine or thiol groups-free and single-phase rock-salt cubic PbSe powder was obtained, producing nanocrystals 16–30 nm in size. X-ray diffraction also showed that the PbSe films containing PbSeO₃ and PbO·xH₂O as impurity phases were produced during the deposition. The morphology of the powders and films was developed by a self-assembly process, in which the primary PbSe nanoparticles self-assemble to produce peanut-like microstructures. Additionally, a non-continuous and porous feature was formed in the thick films. Certain films revealed optical structures characterized by broad- and low-intensity bands resembling an exciton-like behavior. This could be attributed to the presence of nanocrystals with a size less than the Bohr radius, indicating reminiscent quantum effects. The results suggest that the usage of colloidal dispersions as spray solutions represents an effective approach to forming PbSe films, as well as that the synthesis method allows for the elimination of thiol and amine groups before deposition, significantly simplifying the process. Full article

The development of efficient electrocatalysts for hydrogen evolution reactions is an extremely important area for the development of green and clean energy. In this work, a precursor material was successfully prepared via electrodeposition of two doping elements to construct a co-doped cobalt hydroxide electrocatalyst (Ru-Co(OH)₂-Se). This approach was demonstrated to be an effective way to improve the performance of the hydrogen evolution reaction (HER). The experimental results show that the material exhibited a smaller impedance value and a larger electrochemically active surface area. In the HER process, the overpotential was only 109 mV at a current density of 10 mA/cm². In addition, the doping of selenium and ruthenium effectively prevented the corrosion of the catalysts, with the (Ru-Co(OH)₂-Se) material showing no significant reduction in the catalytic performance after 50 h. This synergistic approach through elemental co-doping demonstrated good results in the HER process. Full article

Herein, we synthesized two isostructural supertetrahedral T3 cluster-based chalcogenide compounds by an ionic liquid-assisted precursor technique, namely [Bmmim]₆In₁₀Q₁₆Cl₄∙(MIm)₄ (Q = S (In-S), Q = Se (In-Se), Bmmim = 1-butyl-2,3-dimethylimidazolium, MIm = 1- methylimidazole). The two compounds consist of a pure inorganic discrete supertetrahedral [In₁₀Q₁₆Cl₄]^6- T3 cluster and six charge-balancing [Bmmim]⁺ anions. The T3 clusters could be highly dispersed in dimethyl sulfoxide (DMSO), exposing more photocatalytic active sites, which makes the highly-dispersed In-Se cluster exhibit ~5 times higher photocatalytic H₂ evolution activity than that of the solid-state under visible light irradiation. Comparatively, the photocatalytic performance of the highly-dispersed In-S cluster is only slightly higher than that of the solid state, as its inferior visible-light absorption capability limits the effective utilization of photons. More importantly, through tracking the photogenerated carriers dynamics of highly-dispersed T3 clusters by ultrafast transient absorption (TA) spectroscopy, we found that the photogenerated electrons in the In-S cluster would suffer a rapid internal deactivation process under illumination, whereas the photoexcited electrons in the In-Se cluster can be captured by its surface active centers that would effectively reduce its photogenerated carrier recombination, contributing to the significantly enhanced photocatalytic activity. This work enriches the species of highly-dispersed metal-chalcogenide nanoclusters and firstly investigates the relationship between the structures and photocatalytic performances of nanoclusters by ultrafast excited-state dynamics, which is expected to promote the development of atomically precise nano-chemistry. Full article

Delayed atomic layer deposition (ALD) of ZnO, i.e., area selective (AS)-ALD, was successfully achieved on silicon wafers (Si\SiO₂) terminated with tris(dimethylamino)methylsilane (TDMAMS). This resist molecule was deposited in a home-built, near-atmospheric pressure, flow-through, gas-phase reactor. TDMAMS had previously been shown to react with Si\SiO₂ in a single cycle/reaction and to drastically reduce the number of silanols that remain at the surface. ZnO was deposited in a commercial ALD system using dimethylzinc (DMZ) as the zinc precursor and H₂O as the coreactant. Deposition of TDMAMS was confirmed by spectroscopic ellipsometry (SE), X-ray photoelectron spectroscopy (XPS), and wetting. ALD of ZnO, including its selectivity on TDMAMS-terminated Si\SiO₂ (Si\SiO₂\TDMAMS), was confirmed by in situ multi-wavelength ellipsometry, ex situ SE, XPS, and/or high-sensitivity/low-energy ion scattering (HS-LEIS). The thermal stability of the TDMAMS resist layer, which is an important parameter for AS-ALD, was investigated by heating Si\SiO₂\TDMAMS in air and nitrogen at 330 °C. ALD of ZnO takes place more readily on Si\SiO₂\TDMAMS heated in the air than in N₂, suggesting greater damage to the surface heated in the air. To better understand the in situ ALD of ZnO on Si\SiO₂\TDMAMS and modified (thermally stressed) forms of it, the ellipsometry results were plotted as the normalized growth per cycle. Even one short pulse of TDMAMS effectively passivates Si\SiO₂. TDMAMS can be a useful, small-molecule inhibitor of ALD of ZnO on Si\SiO₂ surfaces. Full article

Orientation-patterned gallium phosphide (OP-GaP) has been grown heteroepitaxially on OP gallium arsenide (GaAs) templates using hydride vapor phase epitaxy (HVPE). The effect of OP-GaAs template fabrication methods of epitaxial-inversion and wafer bonding on the heteroepitaxial OP-GaP growth has been investigated. OP-GaP layers with a growth rate of up to 35 µm/h and excellent domain fidelity were obtained. The growth rate and the domain fidelity have been revealed/studied by scanning electron microscope (SEM). In addition, we demonstrate that the crystalline quality of the individual domains, namely, the substrate-oriented domains (ODs) and the inverted domains (IDs), can be investigated by high-resolution x-ray diffraction reciprocal space mapping (HRXRDRSM), which can also indicate the domain fidelity. Attempts to increase the growth rate and improve the domain fidelity by increasing the III and V group precursors resulted in either an increase in the growth rate in the OP-GaP layers grown on epitaxial inversion OP-GaAs template at the expense of the domain crystalline quality and fidelity or an improvement in the crystalline quality of the domains at the expense of the growth rate in the OP-GaP layers grown on wafer-bonded OP-GaAs templates. In the case of OP-GaP grown on OP-GaAs templates prepared by epitaxial inversion, the crystalline quality of the ODs is better than that of the IDs, but it shows that the quality of the inverted layer in the template influences the quality and fidelity of the grown domains. To the authors’ knowledge, exploitation of HRXRDRSM studies on OP-GaP to establish the crystalline quality of its individual domains (ODs and IDs) is the first of its kind. OP-ZnSe grown on OP-GaAs templates has also been included in this study to further emphasize the potential of this method. We propose from this study that once the growth rate is optimized from SEM studies, HRXRDRSM analysis alone can be used to assess the structural quality and to infer the domain fidelity of the OP structures. Full article

Novel sulfur and selenium substituted 5′,5′-linked dinucleoside pyrophate analogues were prepared in a vibration ball mill from the corresponding persilylated monophosphate. The chemical hydrolysis of pyrophosphorochalcogenolate-linked dimers was studied over a wide pH-range. The effect of the chalcogeno-substitution on the reactivity of dinucleoside pyrophosphates was surprisingly modest, and the chemical stability is promising considering the potential therapeutic or diagnostic applications. The chemical stability of the precursor phosphorochalcogenolate monoesters was also investigated. Hydrolytic desilylation of these materials was effected in aqueous buffer at pH 3, 7 or 11 and resulted in phosphorus-chalcogen bond scission which was monitored using ³¹P NMR. The rate of dephosphorylation was dependent upon both the nature of the chalcogen and the pH. The integrity of the P-S bond in the corresponding phosphorothiolate was maintained at high pH but rapidly degraded at pH 3. In contrast, P-Se bond cleavage of the phosphoroselenolate monoester was rapid and the rate increased with alkalinity. The results obtained in kinetic experiments provide insight on the reactivity of the novel pyrophosphates studied as well as of other types of thiosubstituted biological phosphates. At the same time, these results also provide evidence for possible formation of unexpectedly reactive intermediates as the chalcogen-substituted analogues are metabolised. Full article