Search Results (383)

The present study investigates dye-sensitized solar cells (DSSCs) incorporating natural extracts from the microalgae Spirulina and Chlorella as photosensitizers. TiO₂-based electrodes were prepared and immersed in methanolic algae extracts for 24 and 48 h. UV–Vis spectroscopy revealed absorption peaks near 400 nm and 650 nm, characteristic of chlorophyll. Electrochemical analyses, including photochronoamperometry and open-circuit potential, confirmed the photosensitivity and charge transfer capabilities of all systems. The cell sensitized with Chlorella after 48 h of immersion exhibited the highest energy conversion efficiency (0.0184% ± 0.0015), while Spirulina achieved 0.0105% ± 0.0349 after 24 h. Chlorella’s superior performance is attributed to its higher chlorophyll content and enhanced light absorption, facilitating more efficient electron injection and interaction with the TiO₂ surface. Although the efficiency remains lower than that of conventional silicon-based solar cells, the results highlight the potential of natural colorants as sustainable and low-cost alternatives for photovoltaic applications. Nonetheless, further, improvements are required, particularly in dye stability and anchorage, to improve device performance. This research reinforces the viability of natural photosensitizers in DSSC technology and supports continued efforts to optimize their application. Full article

The motivation for increasing the efficiency of renewable energy sources is the basic problem of ongoing research. Currently, intensive research is underway in technology based on the use of dye-sensitized solar cells (DSSCs). The aim of this work is to investigate the effect of modifying the iodide electrolyte with liquid crystals (LCs) known for the self-organization of molecules into specific mesophases. The current–voltage (I-V) and power–voltage (P-V) characteristics were determined for the ruthenium-based dyes N3, Z907, and N719 to investigate the influence of their structure and concentration on the efficiency of DSSCs. The addition of a nematic LC of 4-n-pentyl-4-cyanobiphenyl (5CB) to the iodide electrolyte influences the I-V and P-V characteristics. A modification of the I-V characteristics was found, especially a change in the values of short circuit current (I_SC) and open circuit voltage (V_OC). The conversion efficiency for cells with modified electrolyte shows a complex dependence that first increases and then decreases with increasing LC concentration. It may be caused by the orientational interaction of LC molecules with the titanium dioxide (TiO₂) layer on the photoanode. A too high concentration of LC may lead to a reduction in total ionic conductivity due to the insulating effect of the elongated polar molecules. Full article

We investigated a novel natural dye-sensitized solar cell (DSSC) utilizing gadolinium ruthenate pyrochlore oxide Gd₂Ru₂O₇ (GRO) as a photoanode and compared its performance to the TiO₂-Gd₂Ru₂O₇ (TGRO) combined-layer configuration. The films were fabricated using the spin-coating technique, resulting in spherical grains with an estimated mean diameter of 0.2 µm, as observed via scanning electron microscopy (SEM). This innovative photoactive gadolinium ruthenate pyrochlore oxide demonstrated strong absorption in the visible range and excellent dye adhesion after just one hour of exposure to natural dye. X-ray diffraction confirmed the presence of the pyrochlore phase, where Raman spectroscopy identified various vibration modes characteristic of the pyrochlore structure. Incorporating Gd₂Ru₂O₇ as the photoanode significantly enhanced the overall efficiency of the DSSCs. The device configuration FTO/compact-layer/Gd₂Ru₂O₇/Hibiscus-sabdariffa/electrolyte(I⁻/I₃⁻)/Pt achieved a high efficiency of 9.65%, an open-circuit voltage (Voc) of approximately 3.82 V, and a current density of 4.35 mA/cm² for an active surface area of 0.38 cm². A mesoporous TiO₂-based DSSC was fabricated under the same conditions for comparison. Using impedance spectroscopy and cyclic voltammetry measurements, we provided evidence of the mechanism of conductivity and the charge carrier’s contribution or defect contributions in the DSSC cells to explain the obtained Voc value. Through cyclic voltammetry measurements, we highlight the redox activities of hibiscus dye and electrolyte (I⁻/I₃⁻), which confirmed electrochemical processes in addition to a photovoltaic response. The high and unusual obtained Voc value was also attributed to the presence in the photoanode of active dipoles, the layer thickness, dye concentration, and the nature of the electrolyte. Full article

Dye-sensitized solar cells (DSSCs) have emerged as a promising technology for converting sunlight into electricity at a low cost; however, it is still necessary to find a photostable, low-cost, and efficient photosensitizer. In this sense, the natural product bixin (Dye 1) has previously been reported as a potential photosensitizer. Thus, the present work reports the full synthesis of diester and diacid hybrids (Dyes 2 and 3, respectively, with corresponding yields of 93% and 52%) using the natural product bixin as a starting material and 1,3,4-oxadiazole ring as a connected point. The hydrolysis step of Dye 2 aims to obtain Dye 3 with a structural capacity to anchor the titanium dioxide (TiO₂) nanofilms via the carboxylic acid group. Both compounds (Dyes 1 and 3) can be adsorbed via pseudo-first order on the surface of TiO₂ nanofilms, reaching saturation after 10 and 6 min of exposure in an organic solution (1 × 10⁻⁵ M), respectively, with adsorption kinetics of the semisynthetic compound almost twofold higher than the natural product. Contrary to expectations, Dye 3 had spectral behavior similar to Dye 1, but with better frontier molecular orbital (FMO) parameters, indicating that Dye 3 will probably behave very similarly or have slightly better photovoltaic performance than Dye 1 in future DSSC measurements. Full article

Dye-sensitized solar cells (DSSCs) are promising alternatives for power generation due to their environmental friendliness, cost effectiveness, and strong performance under diffused light. Conversely, their low spectral response in the ultraviolet (UV) region significantly obliterates their overall performance. The so-called luminescent down-shifting (LDS) presents a practical solution by converting high-energy UV photons into visible light that can be efficiently absorbed by sensitizer dyes. Herein, a conventional solid-state technique was applied for the synthesis of an LDS, europium (II)-doped barium orthosilicate (BaSiO₃:Eu²⁺) material. The material exhibited strong UV absorption, with prominent peaks near 400 nm and within the 200–300 nm range, despite a weaker response in the visible region. The estimated optical bandgap was 3.47 eV, making it well-suited for UV absorbers. Analysis of the energy transfer mechanism from the LDS material to the N719 dye sensitizer depicted a strong spectral overlap of $2\times {10}^{10}{\mathrm{M}}^{-1}{\mathrm{c}\mathrm{m}}^{-1}{\mathrm{n}\mathrm{m}}^4$, suggesting efficient energy transfer from the donor to the acceptor. The estimated Förster distance was approximately $6.83\mathrm{n}\mathrm{m}$, which matches the absorption profile of the dye-sensitizer. Our findings demonstrate the potential of BaSiO₃:Eu²⁺ as an effective LDS material for enhancing UV light absorption and improving DSSC performance through increased spectral utilization and reduced UV-induced degradation. Full article

The development of dye-sensitized solar cells (DSSCs) has gained prominence as an economical alternative for photovoltaic energy conversion. This work investigates the synthesis of niobium pentoxide (Nb₂O₅) by the Pechini method, followed by calcination at different temperatures (500 °C, 600 °C and 700 °C) to evaluate its structural, morphological, and electrochemical properties as a photoanode material in DSSCs. SEM and XRD analyses revealed that calcination at 600 °C produced a material with optimized particle size (642.17 ± 37 nm) and adequate crystalline structure, favoring dye adsorption and electronic transport. Electrochemical characterization, including open-circuit potential and impedance spectroscopy, indicated that the sample at 600 °C presented superior photovoltaic performance, achieving a power conversion efficiency of 1.39% and electron lifetime equal to 0.159 s. These findings suggest that Nb₂O₅, under controlled calcination conditions, may act as a promising alternative to TiO₂ substitution in DSSC applications. Full article

The tungsten (W)-modified TiO₂ films were fabricated on the fluorine-doped TiO₂ substrates using the sol–gel process. The influences of W dopant on the photovoltaic properties of the tungsten-modified TiO₂ DSSC were analyzed, too. The crystallization and dye absorption of tungsten-modified TiO₂ thin films increased more than those of the undoped TiO₂ thin films. Furthermore, the optimal performances of the V_oc, J_sc, fill factor, and efficiency of the DSSC with tungsten-modified TiO₂ thin films were 0.68 V, 16.28 mA/cm², 65.5%, and 7.03%, respectively. The enhancement was mainly due to the improved crystallinity and increased dye adsorption of the tungsten-modified TiO₂ thin films, which contributed to improving the efficiency of the dye-sensitized solar cell. Full article

Optoelectronic devices, which combine optics and electronics, are vital for converting light energy into electrical energy. Various solar cell technologies, such as dye-sensitized solar cells (DSSCs), silicon solar cells, and perovskite solar cells, among others, belong to this category. DSSCs have gained significant attention due to their affordability, flexibility, and ability to function under low light conditions. The current research incorporates machine learning (ML) models to predict the performance of a modified Eu³⁺-doped Y₂WO₆/TiO₂ photo-electrode DSSC. Experimental data were collected from the “Dryad Repository Database” to feed into the models, and a detailed data visualization analysis was performed to study the trends in the datasets. The support vector regression (SVR) and Random Forest regression (RFR) models were applied to predict the short-circuit current density (J_sc) and maximum power (P_max) output of the device. Both models achieved reasonably accurate predictions, and the RFR model attained a better prediction response, with the percentage difference between the experimental data and model prediction being 0.73% and 1.01% for the J_sc and P_max respectively, while the SVR attained a percentage difference of 1.22% and 3.54% for the J_sc and P_max respectively. Full article

In this work, a biochar catalyst was developed from residual brewery spent grain (BSG) biomass and iron oxide to be applied in the counter electrode (CE) in dye-sensitized solar cells (DSSCs). The composite was obtained using a two-stage methodology based on microwave-assisted hydrothermal carbonization and pyrolysis, evaluating the influence of the pyrolysis temperature (700, 800 and 900 °C) on the properties and performance of the material. As result, composites with a high carbon and iron oxide content were obtained in a magnetite state attached to the surface. Furthermore, the physicochemical characteristics of the biochar showed similarities to those of reduced graphene oxide (rGO), which was attributed to the incorporation of iron oxide and the pyrolysis temperature. Electrochemical analysis showed that the composite pyrolyzed at 800 °C presented better catalytic activity and lower charge transfer resistance. Its application in the CE of a DSSC presented a current density of 10.44 mA/cm² and an efficiency of 3.05%, values close to the conventional Pt catalyst in DSSCs (Pt = 4.43%). This study validates the use of a composite based on residual brewery biomass with iron oxide in a CE, making it an alternative that contributes to the recovery of residues and the generation of sustainable technologies. Full article

Almost forty years ago, dye-sensitized solar cells (DSSCs) appeared as a promising route for harnessing the energy of the sun and for converting it into electricity. In the following years, a huge number of studies have been dedicated to increase the global photovoltaic efficiencies and stability of DSSCs. Thiocyanate ruthenium complexes bearing chelating nitrogen donor ligands turned out to be among the best performing photosensitizers. In the last 15 years, a lot of work has also been dedicated to the preparation of efficient thiocyanate-free Ru dyes. In this review, these two families of ruthenium(II) complexes are presented: (a) dyes presenting thiocyanate ligands and (b) thiocyanate-free dyes. The coverage, mainly from 2021, is not exhaustive, but exemplifies the most recent design approaches and photovoltaic properties of these two classes of Ru(II) photosensitizers. Full article

Although photovoltaic (PV) solar cells have been widely used for a variety of applications, several critical issues are yet to be addressed, including further enhanced power conversion efficiency (PCE) and their 2D solar harvesting with limited land availability. It has been reported that traditional PV installations require approximately 22,000 square miles to power the entire United States—posing a significant barrier, particularly in urban and agricultural settings. A unique dual modality of PV system has been proposed and implemented for both power generation and crop photosynthesis, namely, agrivoltaics. This system installs PV panels over the crops while harvesting solar for PV electricity generation and, at the same time, integrates with crop cultivation, which is a promising solution to optimize land utilization. However, for opaque PV panels, sunlight is often obstructed, potentially impacting plant growth and yield. To address this critical issue, a 3D solar harvesting concept has been proposed and experimentally investigated. By placing multiple layers of transparent PV panels parallel, sunlight can penetrate multiple layers and generate electricity on each PV, significantly enhancing the solar harvesting surface area. Most importantly, sunlight can also be collected by the crops underneath for effective photosynthesis. Among various PV materials, dye-sensitized solar cells (DSSCs) using porphyrin-based dyes have demonstrated potential for spectral modulation, optimizing both electricity generation and crop illumination. This review focuses on a novel approach to a 3D solar harvesting system via a multi-layered PV architecture for agrivoltaics. Also discussed are the current challenges in agrivoltaics, spectral selective mechanisms, and 3D solar harvesting architecture that show promise for sustainable energy production and land-efficient solar power deployment. Full article

The development of efficient dyes for photon harvesting in dye-sensitized solar cells (DSSCs) is a critical area of research with the potential to enhance renewable energy technologies. This manuscript presents a novel approach to engineering dye structures (abbreviated as D2 dye features, an anthanthrene core with a resonance energy of E_R = 694 kJ/mol and a reported power conversion efficiency (η) of 5.27%) by systematically replacing an anthanthrene core with various aromatic cores, aiming to understand the influence of resonance energy on molecular performance. By designing seven new dyes with resonance energies ranging from 255 to 529 kJ/mol, we conducted in-depth computational studies using Density Functional Theory (DFT) and Time-Dependent Density Functional Theory (TDDFT) to explore the effects of π-aromatic linkers on their electronic properties. Our findings reveal key insights into intermolecular charge-transfer (ICT) mechanisms and how they relate to the resonance energy of dye cores, highlighting the significance of balanced charge mobilities in optimizing optoelectronic characteristics, as shown by the D9 dye with a naphthacene core. Full article

This work proposes dye-sensitized solar cells (DSSCs) with various photoanode designs. A hydrothermal method is used to synthesize hydrangea-shaped TiO₂ (H-TiO₂) aggregates. The X-ray diffraction (XRD) pattern of H-TiO₂ reveals only an anatase phase. No peaks of any other phases are detected, indicating that the hydrangea-shaped TiO₂ is phase-pure. The size of the synthesized H-TiO₂ is approximately 300 nm to 2 μm, and its particle size is suitable for use in the scattering layer of a DSSC. Mixing the P25 TiO₂ into the H-TiO₂ aggregate with the best mixing ratio can significantly improve the conversion efficiency of DSSCs. When the ratio of H-TiO₂:P25 TiO₂ = 3:7, the scattering layer has the optimal parameters, as determined experimentally. The optimal structure is a double layer that is formed of five layers of P25 TiO₂ plus a single scattering layer. An open circuit voltage (V_oc) of 0.77 V, short-circuit current (J_sc) of 15.26 mA/cm², fill factor (FF) of 0.71, conversion efficiency (η) of 8.33%, and charge-collection efficiency (η_cc) of 0.96 are obtained from the optimally designed photoelectrode. To the best of the authors’ knowledge, this work is the first in which large particles of hydrangea are mixed with small particles of P25 TiO₂ in various proportions to form a scattering layer. Full article

With the rising levels of atmospheric CO₂, electrochemistry shows great promise in decarbonizing industrial processes by converting CO₂ into valuable products through scalable and sustainable technologies. In this framework, the present study investigates the solar-driven CO₂ reduction toward carbon monoxide, achieved by the integration between the electrochemical reactor and dye-sensitized solar cells (DSSCs), both in experimental and modeling perspectives. COMSOL^® Multiphysics 6.3 was used to develop a detailed finite element method model of the electrochemical cell integrated with a photovoltaic module, validated with the experimental results that demonstrated a strong correlation. A 2D model was designed, incorporating cathode and anode regions divided by an ion-exchange membrane. The model includes platinum foil and silver nanoparticles as catalysts for the oxygen evolution reaction and CO₂ reduction reaction, respectively. Integration with the fundamental equations of the DSSCs was simulated to analyze the solar-driven CO₂ reduction behavior under solar irradiance variations, offering a valuable tool for optimizing operating conditions and predicting the device performance under different environmental conditions. The integrated device successfully produces CO with a faradaic efficiency of 73.85% at a current density of J = 3.35 mA/cm² under 1 sun illumination, with the result validated and reproduced by the mathematical model. Under reduced illumination conditions of 0.8 and 0.6 suns, faradaic efficiencies of 68.5% and 64.1% were achieved, respectively. Full article

This study proposes an alternative process for obtaining ZnO/ZnS:rGO heterostructures for use in DSSCs and as promising materials for potential applications in other photonic process, such as photocatalysis and photodetection. The compound was obtained through a microwave-assisted hydrothermal method, where the electromagnetic waves and temperature were crucial points for forming ZnO, ZnO/ZnS and reducing graphene oxide (GO). The XRD, Raman, FT-IR, and FESEM results presented the structural, morphological, and chemical structures, which suggest the conversion of ZnO to ZnS for samples with higher concentrations of reduced graphene oxide (rGO). Additionally, the optical properties were analyzed through photoluminescence and UV-Vis measurements. The electrical behavior of the photoelectrodes was investigated through J-V measurements in light and dark conditions. In addition, electrochemical impedance spectroscopy (EIS) was performed and Bode phase plots were created, analyzing the recombination processes and electron lifetime. The J-V results showed that for smaller amounts of rGO, the dye-sensitized solar cells (DSSC) efficiency improved compared to the ZnO/ZnS single structure. However, it was observed that with more significant amounts of rGO, the photocurrent value decreased due to the presence of charge-trapping centers. On the other hand, the best results were obtained for the ZnO/ZnS:1% rGO sample, which showed an increase of 14.2% in the DSSC efficiency compared to the pure ZnO/ZnS photoelectrode. Full article