Search Results (39)

The increasing adoption of electric vehicles (EVs) has led to a surge in end-of-life (EOL) lithium-ion batteries (LIBs), necessitating efficient recycling strategies to mitigate environmental risks and recover critical materials. This study compares the EV battery recycling frameworks in China and the United States, focusing on policy effectiveness, technological advancements, and material recovery efficiencies. China’s extended producer responsibility (EPR) policies and 14th Five-Year Plan mandate strict recycling targets, achieving a 40% battery recycling rate with 90% material recovery efficiency. Hydrometallurgical methods dominate, reducing energy consumption by 50% compared to virgin material extraction. The US, leveraging incentive-based mechanisms and private sector innovations, has a 35% recycling rate but a higher 95% resource recovery efficiency, mainly due to direct recycling and AI-based sorting technologies. Despite these advancements, challenges remain, including high recycling costs, inconsistent global regulations, and supply chain inefficiencies. To enhance sustainability, this study recommends harmonized international policies, investment in next-generation recycling technologies, and second-life battery applications. Emerging innovations, such as AI-driven sorting and direct cathode regeneration, could increase recovery efficiency by 20–30%, further reducing lifecycle costs. By integrating synergistic policies and advanced recycling infrastructures, China and the US can set a global precedent for sustainable EV battery management, driving the transition toward a circular economy. Future research should explore life cycle cost analysis and battery reuse strategies to optimize long-term sustainability. Full article

This study aimed to investigate the effects of combined ultrasound and osmotic pretreatment conditions on the drying kinetics and antioxidant properties, such as total phenolic content (TPC), total flavonoid content (TFC), vitamin C content, and DPPH radical scavenging activity, of dried Citrus macroptera (Satkara) fruits. The fruit slices were immersed in 10% aqueous solutions of sucrose (S), glucose (G), and fructose (F) followed by an ultrasound treatment (40 kHz) for 10, 20, or 30 min. The samples were then dried in a convective oven at 50, 60, or 70 °C and 30% relative humidity with a constant air velocity of 3 m s⁻¹. Four thin-layer kinetic models, namely Page, Newton, Henderson and Pabis, and Logarithmic, were evaluated. Among these, Page was found to be the most suitable model for predicting the drying kinetics. The pretreatment process accelerated the drying process significantly, reducing the drying time up to 6 h. Additionally, the pretreated samples exhibited improved retention of quality attributes, with vitamin C being best preserved in S solutions, TPC in both S and F solutions, TFC in F solutions, and DPPH in all three sugar solutions (S, F, and G). The application of ultrasound during osmotic treatment also had a positive impact on TPC and TFC retention, whereas it presented a negative effect on vitamin C when used for a prolonged duration and a negligible one on the antioxidant capacity. Overall, this study provides a new perspective on the drying kinetics of Satkara fruits, and their respective properties after drying, and being subjected to combined ultrasound and osmotic pretreatment. These findings will contribute to the development of effective and efficient drying methods suitable for industrial applications to produce dried Satkara products with a minimum quality degradation. Full article

This research article investigates the recycling of end-of-life solar photovoltaic (PV) panels by analyzing various mechanical methods, including Crushing, High Voltage Pulse Crushing, Electrostatic Separation, Hot Knife Cutting, Water Jet Cutting, and Magnetic Separation. Each method’s effectiveness in extracting materials such as glass, silicon, metals (copper, aluminum, silver, tin, lead), and EVA was evaluated. The analysis reveals that no single method is entirely sufficient for comprehensive material recovery. Based on the data analysis, a new hypothetical hybrid method, Laser and High Voltage Pulse (L&HVP), is proposed, which integrates the precision of laser irradiation with the robustness of high voltage pulse crushing. The laser irradiation step would theoretically facilitate the removal of the ethylene-vinyl acetate (EVA) encapsulant, preparing the materials for subsequent separation. The high high-voltage pulse crushing would then selectively fragment and separate the remaining components, potentially enhancing material recovery efficiency while minimizing contamination. The proposed approach is grounded in the observed limitations of existing techniques. This method aims to offer a more comprehensive and sustainable solution for solar PV module recycling. Further research and experimentation are necessary to validate the effectiveness of the L&HVP method and its potential impact on the field of solar PV recycling. Full article

This paper examines the end-of-life (EOL) waste management regulations and guidelines of five leading countries—China, USA, India, Japan, and Germany—to identify best practices and lessons that can enhance Saudi Arabia’s EOL waste management strategies. The study delves into China’s regulatory framework, highlighting its import bans on certain wastes, the USA’s manufacturer responsibility requirements for product disposal, India’s engagement of the informal sector in waste collection and recycling, Japan’s take-back system mandating manufacturer responsibility for product recovery and recycling, and Germany’s advanced system promoting the separate collection of EOL products and stringent hazardous waste regulations. By evaluating these diverse regulatory approaches and integrating insights from recent literature, this paper aims to provide a comprehensive perspective to assist Saudi Arabia in developing an effective EOL waste management system. Given the current state and deployment of solar PV systems in Saudi Arabia, the generation of PV solar panel waste is currently minimal. However, future projections indicate a significant increase, and it is worrisome that the KSA currently lacks the necessary systems and infrastructure to handle this waste effectively. To address this challenge sustainably, it is essential to introduce and implement an Extended Producer Responsibility (EPR) policy, develop robust recycling infrastructure, enhance public awareness and education, and foster public–private partnerships. These measures will provide a strong foundation for managing end-of-life PV solar panel waste in Saudi Arabia. Such a system would ensure environmental protection, public health, and economic growth. Moreover, the research findings could serve as a valuable resource for other countries seeking to improve their EOL waste management practices. This study underscores the importance of learning from successful international waste management practices to enhance EOL waste management systems globally. Full article

The demand for vaccines, particularly those prepared from non-conventional sources, is rising due to the emergence of drug resistance around the globe. Probiotic-based vaccines are a wise example of such vaccines which represent new horizons in the field of vaccinology in providing an enhanced and diversified immune response. The justification for incorporating probiotics into vaccines lies in the fact that that they hold the capacity to regulate immune function directly or indirectly by influencing the gastrointestinal microbiota and related pathways. Several animal-model-based studies have also highlighted the efficacy of these vaccines. The aim of this review is to collect and summarize the trends in the recent scientific literature regarding the role of probiotics in vaccines and vaccinology, along with their impact on target populations. Full article

Obesity is a source of significant pathologies and deadly diseases, including heart disease, diabetes, and cancer. One of the most intriguing strategies in the hunt for new anti-obesity medications is the inhibition of pancreatic lipase (PL). This study presents a novel application of short α and β-mixed peptides as pancreatic lipase inhibitors. These peptides were synthesized in the solution phase and characterized using FTIR and ¹H-NMR. L-proline is present in a high percentage of natural anti-lipase peptides and was used as a β-amino acid in this study to enhance anti-lipase activity and proteolytic stability. Moreover, L-α-proline was converted to β-amino acid derivatives using the Arndt–Eistert method with the advantage of stereo control at the α-carbon. The synthesized peptides with anti-lipase activity are N-Boc-β-Pro-Gly-OBz (93%), N-Boc-O-Bz-Tyr-β-Pro-β-Pro-Gly-OBz (92%), N-Boc-O-Bz-Tyr-β-Pro-COOH (91%), N-Boc-Phe-β-Pro-OCH₃ (90%), and N-Boc-O-Bz-Tyr-β-Pro-OCH₃ (89%). These peptides may function as lead molecules for further modification to more significant molecules, which can help control obesity. Full article

High-yield potential perennial crops, such as Miscanthus spp. and Arundo donax are amongst the most promising sources of sustainable biomass for bioproducts and bioenergy. Although several studies assessed the agronomic performance of these species on diverse marginal lands, research to date on drought and zinc (Zn) resistance is scarce. Thus, the objective of this study was to investigate the drought and Zn stress tolerance of seven novel Miscanthus hybrids and seven Arundo clones originating from different parts of Italy. We subjected both species to severe drought (less than 30%), and Zn stress (400 mg/kg⁻¹ of ZnSO₄) separately, after one month of growth. All plants were harvested after 28 days of stress, and the relative drought and Zn stress tolerance were determined by using a set of morpho-physio-biochemical and biomass attributes in relation to stress tolerance indices (STI). Principal component analysis (PCA), hierarchical clustering analysis (HCA) and stress tolerance indices (STI) were performed for each morpho-physio-biochemical and biomass parameters and showed significant relative differences among the seven genotypes of both crops. Heatmaps of these indices showed how the different genotypes clustered into four groups. Considering PCA ranking value, Miscanthus hybrid GRC10 (8.11) and Arundo clone PC1 (11.34) had the highest-ranking value under both stresses indicating these hybrids and clones are the most tolerant to drought and Zn stress. In contrast, hybrid GRC3 (−3.33 lowest ranking value) and clone CT2 (−5.84) were found to be the most sensitive to both drought and Zn stress. Full article

Postpartum infection of the uterus by pathogenic bacteria is exacerbated due to a lack of sufficient epidemiological studies and evidence-based therapeutics. Therefore, this study was planned to find the prevalence, risk factors, and drug-resistance profile of S. aureus and E. coli isolated from bovine endometritis and to evaluate the antibacterial potential of sodium alginate-based antibiotics and nanoparticles. The study revealed 34.21% S. aureus and 31.57% E. coli, whereas most of the assumed risk factors presented significant association in this study. S. aureus showed the highest resistance against fusidic acid (60%) and cefoxitin (50%), while the highest resistance in E. coli was found against fusidic acid (60%), gentamicin (60%), chloramphenicol (50%), and cefoxitin (50%). Tylosin coupled with MgO nanoparticles stabilized in sodium alginate gel (Tylo + MgO + gel) presented significantly lower minimum inhibitory concentration (MIC) against E. coli, showing 13.88 ± 4.51 µg/mL after 24 h incubation. On the other hand, gel-based preparations showed MIC as 31.25 ± 0 µg/mL (Tylo + gel + MgO) and 26.04 ± 9.02 µg/mL (Tylo + Gel) against S. aureus. Generally, the MICs of non-gel-based preparations were significantly higher against bacteria except ampicillin against S. aureus in this study. The toxicity analysis of MgO nanoparticles presented 20–80% mortality of snails against a wider range of 0.01 mg/mL–10 mg/mL. The histopathological parameters concluded MgO nanoparticles safe to use on off targets. The current study thus concludes the rise in antimicrobial resistance while the gel-based products appearing as effective antimicrobials with sufficient safety margins for off-targets. The study thus invites further investigation for the development of suitable and affordable modified therapeutics for better health and production of animals. Full article

Polymicrobial mastitis is now becoming very common in dairy animals, resulting in exaggerated resistance to multiple antibiotics. The current study was executed to find drug responses in individual and mixed Culture of Staphylococcus aureus and Escherichia coli isolated from milk samples, as well as to evaluate the antibacterial potential of tungsten oxide nanoparticles. These isolates (alone and in mixed culture) were further processed for their responses to antibiotics using the disc diffusion method. On the other hand, tungsten oxide WO₃ (W) nanoparticles coupled with antibiotics (ampicillin, A, and oxytetracycline, O) were prepared through the chemical method and characterized by X-ray diffraction, scanning electron microscopy (SEM), and UV-visible techniques. The preparations consisting of nanoparticles alone (W) and coupled with ampicillin (WA) and oxytetracycline (WO) were tested against individual and mixed Culture through the well diffusion and broth microdilution methods. The findings of the current study showed the highest resistance in E. coli was against penicillin (60%) and ampicillin (50%), while amikacin, erythromycin, ciprofloxacin, and oxytetracycline were the most effective antibiotics. S. aureus showed the highest resistance against penicillin (50%), oxytetracycline (40%), and ciprofloxacin (40%), while, except for ampicillin, the sensitive strains of S. aureus were in the range of 40–60% against the rest of antibiotics. The highest zones of inhibition (ZOI) against mixed Culture were shown by imipenem and ampicillin, whereas the highest percentage decrease in ZOI was noted in cases of ciprofloxacin (−240%) and gentamicin (−119.4%) in comparison to individual Culture of S. aureus and E. coli. It was noteworthy that the increase in ZOI was not more than 38% against mixed Culture as compared to the individual Culture. On the other hand, there was a significant reduction in the minimum inhibitory concentration (MIC) of nanoparticle-coupled antibiotics compared to nanoparticles alone for individual and mixed-culture bacteria, while MICs in the case of mixed Culture remained consistently high throughout the trial. This study therefore concluded that diverse drug resistance was present in both individual and mixed-culture bacteria, whereas the application of tungsten oxide nanoparticle-coupled antibiotics proved to be an effective candidate in reversing the drug resistance in bacterial strains. Full article

This study focused on the assessment of the antimicrobial resistance of Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli) isolated from bovine mastitis milk samples and the revealing anti-mastitis potential of phytocompounds of Ziziphus jujube and Acacia nilotica through molecular docking analysis. The mastitis milk samples were collected from various dairy farms for the isolation of the bacteria (S. aureus and E. coli) and their response to antibiotics. Ethanolic extracts of both plants were prepared. Their antibacterial activity was evaluated, and they were processed for phytochemical analysis after which, molecular docking analysis with pathogenic proteins of the bacteria was carried out. Parametric and non-parametric statistical analyses were performed to reach the conclusions of this study. The findings of the study revealed a higher drug resistance (≥40%) of E. coli against ampicillin, amikacin, and vancomycin, while S. aureus exhibited the highest resistance to ampicillin, erythromycin, and ciprofloxacin. The ethanolic extracts of the Ziziphus jujube and Acacia nilotica plants produced a ZOI between 18 and 23 mm against multidrug-resistant S. aureus and E. coli. Gas chromatography–mass spectrophotometry (GC–MS) was used to explore 15 phytocompounds from Ziziphus jujube and 18 phytocompounds from Acacia nilotica. The molecular docking analysis of 2cyclopenten−1-one,3,4,4 trimethyl and Bis (2ethylhexyl) phthalate of Ziziphus jujube showed a binding affinity of −4.8 kcal/mol and −5.3 kcal/mol and −5.9 kcal/mol and −7.1 kcal/mol against the DNA Gyrase and toxic shock syndrome toxin-1 proteins of S. aureus and E. coli, respectively. The suberic acid monomethyl ester of Acacia nilotica showed a binding affinity of −5.9 kcal/mol and −5 kcal/mol against the outer membrane protein A and Topoisomerase IV protein of E. coli and −5.1 kcal/mol and −5.8 kcal/mol against the toxic shock syndrome toxin-1 and Enterotoxin B proteins of S. aureus. Similarly, 2,2,4-trimethyl-1,3-pentanediol di-iso-butyrate showed a binding affinity of −6.5 kcal/mol and −5.3 kcal/mol against the outer membrane protein A and Topoisomerase IV of E. coli and −5.2 kcal/mol and −5.9 kcal/mol against the toxic shock syndrome toxin-1 and Enterotoxin B proteins of S. aureus, respectively. The study concluded that there was an increasing trend for the antimicrobial resistance of S. aureus and E. coli, while the Ziziphus jujube and Acacia nilotica plant extracts expressed significant affinity to tackle this resistance; hence, this calls for the development of novel evidence-based therapeutics. Full article

Inflammation-related diseases are major causes of mortality and disability worldwide. This study aimed to identify and investigate probiotic bacteria that could be present in Al-Asfar Lake in Al-Ahsa City, Saudi Arabia to prevent the inflammatory responses of carrageenan-induced paw edema. In total, seven active strains were isolated, and three isolates (ASF-1, ASF-2, and ASF-3) exhibited a positive Gram stain and viable growth at 20% NaCl salinity; they also lacked catalase and hemolytic activities and had high levels of cell surface hydrophobicity (CSH). They also demonstrated potent antibacterial activity against Salmonella typhi and Staphylococcus aureus. These results revealed that ASF-2 had probiotic qualities, and it was selected for further research. ASF-2 demonstrated significant anti-inflammatory effects in an experimental model of carrageenan-induced paw edema; the experimental model showed decreased levels of pro-inflammatory markers, such as interleukin 6 (IL-6), interleukin 17 (IL-17), and transforming growth factor-β (TGF-β), and an increased level of an anti-inflammatory marker (interferon gamma (IFN-γ)). Animals in the control group saw a 45% decrease in edema when compared to mice in the carrageenan group. When comparing tissue damage and infiltration in the ASF-2-treated and non-treated mice, the histological examination of the sub-planar tissues of the hind leg revealed that the inflamed tissues had healed. The 16S rRNA sequencing method was utilized to establish that ASF-2 is, in fact, Enterococcus lactis with a 99.2% sequence similarity. These findings shed further light on ASF-2’s potential as a biocompatible anti-inflammatory medication. Full article

This study aims to explore the moderating effect of trust on the relationship between social media engagement, relationship benefits, and social relationships, utilizing an innovative framework grounded in social exchange theory. Employing a quantitative analysis with structural equation modeling (SEM), using a questionnaire distributed to a sample of 493 Jordanian youth, the results unveil a positive correlation between social media engagement and social relationships, with trust emerging as a crucial moderator in this dynamic. Trust positively moderates the connection between social media engagement and social relationships. This research sheds light on the pivotal role of trust in shaping social relationships on social media platforms. However, the interaction between trust and relationship benefits does not significantly impact social relationships. By expanding on existing knowledge, this study offers a fresh perspective on the interplay between trust, social media engagement, relationship benefits, and social relationships, emphasizing the potential of understanding trust to foster stronger social connections in the digital age. The results suggest that the positive influence of social media engagement on social relationships possibly will be determined by the level of trust present inside online communities. Full article

Alternative and modified therapeutic approaches are key elements in culminating antibiotic resistance. To this end, an experimental trial was conducted to determine the cytotoxicity and antibacterial potential of composites of magnesium oxide (MgO) nanoparticles and antibiotics stabilized in sodium alginate gel against multi-drug-resistant Staphylococcus aureus isolated from a houbara bustard. The characterization of preparations was carried out using X-ray diffraction (XRD), scanning transmissible electron microscopy (STEM), and Fourier-transform infrared spectroscopy (FTIR). The preparations used in this trial consisted of gel-stabilized MgO nanoparticles (MG), gel-stabilized tylosin (GT), gel-stabilized ampicillin (GA), gel-stabilized cefoxitin (GC), gel-stabilized MgO and tylosin (GMT), gel-stabilized MgO and cefoxitin (GMC), and gel-stabilized MgO and ampicillin (GMA). The study presents composites that cause a lesser extent of damage to DNA while significantly enhancing mitotic indices/phases compared to the other single component preparations with respect to the positive control (methyl methanesulphonate). It was also noted that there was a non-significant difference (p > 0.05) between the concentrations of composites and the negative control in the toxicity trial. Studying in parallel trials showed an increased prevalence, potential risk factors, and antibiotic resistance in S. aureus. The composites in a well diffusion trial showed the highest percentage increase in the zone of inhibition in the case of GT (58.42%), followed by GMT (46.15%), GC (40.65%), GMC (40%), GMA (28.72%), and GA (21.75%) compared to the antibiotics alone. A broth microdilution assay showed the lowest minimum inhibitory concentration (MIC) in the case of GMA (9.766 ± 00 µg/mL), followed by that of GT (13.02 ± 5.64 µg/mL), GMC (19.53 ± 0.00 µg/mL), GA (26.04 ± 11.28 µg/mL), GMT (26.04 ± 11.28 µg/mL), MG (39.06 ± 0.00 µg/mL), and GC (39.06 ± 0.00 µg/mL). The study thus concludes the effective tackling of multiple-drug-resistant S. aureus with sodium-alginate-stabilized MgO nanoparticles and antibiotics, whereas toxicity proved to be negligible for these composites. Full article

The present study was conducted to evaluate the quality of drinking water and assess the potential health hazards due to water contaminants in selected urban areas of Lahore, Pakistan. Water samples were collected from ten sites and analyzed for different physico-chemical parameters including turbidity, color, pH, total dissolved solids (TDS), nitrates, fluoride, residual chlorine, and total hardness. Additionally, heavy metal (arsenic) and microbial parameters (E. coli) were also determined in the water samples. Drinking water quality evaluation indices, including the water quality index (WQI) for physico-chemical and biological parameters and human health risk assessment (HHRA) for heavy metal were estimated using the analytical results of the target parameters. It was found in most of the areas that the levels of arsenic, fluoride, TDS, and residual chlorine were higher than those recommended by the National Environmental Quality Standard (NEQS) and World Health Organization (WHO) guidelines. In addition to the physico-chemical parameters, microbial content (E. coli) was also found in the drinking water samples of the selected areas. Statistical analysis of the results indicated that levels of target parameters in drinking water samples are significantly different between sampling sites. The WQI for all physico-chemical and microbial parameters indicated that drinking water in most of the areas was unfit and unsuitable (WQI > 100) for drinking purposes except for the water of Bhatti Gate and Chota Gaon Shahdara with a WQI of 87 and 91, respectively. Drinking water in these areas had a very poor WQI rating. According to HHRA, drinking water from the selected sites was found to be of high risk to children and adults. The carcinogenic risk of arsenic indicated that all samples were of high risk to both adults and children (4.60 and 4.37 × 10⁻³, respectively). Regular monitoring of drinking water quality is essential, and proactive measures must be implemented to ensure the treatment and availability of safe drinking water in urban areas. Full article

Organic optoelectronic devices have received appreciable attention due to their low cost, mechanical flexibility, band-gap engineering, lightness, and solution processability over a broad area. Specifically, realizing sustainability in organic optoelectronics, especially in solar cells and light-emitting devices, is a crucial milestone in the evolution of green electronics. Recently, the utilization of biological materials has appeared as an efficient means to alter the interfacial properties, and hence improve the performance, lifetime and stability of organic light-emitting diodes (OLEDs). Biological materials can be known as essential renewable bio-resources obtained from plants, animals and microorganisms. The application of biological interfacial materials (BIMs) in OLEDs is still in its early phase compared to the conventional synthetic interfacial materials; however, their fascinating features (such as their eco-friendly nature, biodegradability, easy modification, sustainability, biocompatibility, versatile structures, proton conductivity and rich functional groups) are compelling researchers around the world to construct innovative devices with enhanced efficiency. In this regard, we provide an extensive review of BIMs and their significance in the evolution of next-generation OLED devices. We highlight the electrical and physical properties of different BIMs, and address how such characteristics have been recently exploited to make efficient OLED devices. Biological materials such as ampicillin, deoxyribonucleic acid (DNA), nucleobases (NBs) and lignin derivatives have demonstrated significant potential as hole/electron transport layers as well as hole/electron blocking layers for OLED devices. Biological materials capable of generating a strong interfacial dipole can be considered as a promising prospect for alternative interlayer materials for OLED applications. Full article