Colorants, Volume 2, Issue 4 (December 2023) – 7 articles

Y(Mn_0.95M_0.05)₂O₅ (M = Al, Fe, Ga, Ti, and Zr) samples were synthesized via a sol–gel method using citric acid to find a new near-infrared (NIR) reflective black pigment. Among these samples, the optical reflectance of Y(Mn_0.95Fe_0.05)₂O₅ and Y(Mn_0.95Ga_0.05)₂O₅ in the near-infrared region was found to be larger than that of YMn₂O₅. Then, the concentration of the dopant (Fe or Ga) was changed between 0 and 15%, and the resulting UV–Vis–NIR reflectance spectra were measured. As a result, the optical reflectance of the Fe-doped samples decreased in the near-infrared region, while that of the Ga-doped samples increased. Accordingly, Y(Mn_1−xGa_x)₂O₅ (0 ≤ x ≤ 0.20) samples were synthesized, and the crystal structure, particle size, optical properties, and color of the samples were characterized. The single-phase samples were obtained in the composition range of 0 ≤ x ≤ 0.15, and the lattice volume decreased with increasing Ga³⁺ concentration. Optical absorption below 850 nm was attributed to the charge transfer transition between O_2p and Mn_3d orbitals, and the absorption wavelength of Y(Mn_1−xGa_x)₂O₅ shifted to the shorter wavelength side as the Ga³⁺ content increased, because of the decrease in the Mn³⁺ concentration. Although the sample color became slightly reddish black by the Ga³⁺ doping, the solar reflectance in the near-infrared region reached 47.6% at the composition of Y(Mn_0.85Ga_0.15)₂O₅. Furthermore, this NIR reflectance value was higher than those of the commercially available products (R < 45%). Full article

Due to the high stability of azo-type dyes, conventional treatment processes such as adsorption, flocculation, and activated sludge are not efficient for decolorizing wastewater effluents. An alternative to traditional wastewater treatment is photocatalysis, which has gained significant interest because research has shown it to be a viable and cost-effective process that uses sunlight as an inexhaustible energy source. In heterogeneous photocatalysis, a photocatalyst is required, such as TiO₂, ZnO, composite materials, and, more recently, metal–organic frameworks (MOFs). MOFs, also known as “coordination polymers”, exhibit photocatalytic properties and have been proven to be promising materials in the photocatalytic degradation of dyes. This study presents recent advances in using MOFs as photocatalysts to degrade recalcitrant contaminants like azo-type dyes. Recent advancements in developing photocatalysts based on MOFs are focused on two strategies. Firstly, the development of new MOFs composed of complex ligands or a mixed ligand system, and secondly, the synthesis of composite materials based on MOFs and metal oxides, metals, sulfides, nitrides, etc. Both strategies have significantly contributed to the search for new semiconductors to degrade some recalcitrate contaminants in wastewater. Full article

The design and development of sensitizing dyes possessing wide-wavelength photon harvesting encompassing visible to near-infrared (NIR) wavelength regions are unavoidable for increasing the overall efficiency of dye-sensitized solar cells (DSSCs). In this study, three far-red-sensitive squaraine sensitizers were designed computationally, synthesized, and characterized, aiming towards their suitability as a potential sensitizer for DSSCs. It has been found that the incorporation of an electron acceptor moiety in the central squaraine core brought about a red shift in the absorption maximum (λ_max) and the emergence of a secondary absorption band in the blue region, thus broadening the photon-harvesting window. In addition, it also lowered the dye’s HOMO energy level enabling a facile regeneration of the photo-excited dye, which improved the photovoltaic performance of SQ-223, exhibiting a photoconversion efficiency (PCE) of 4.67%. Thereafter, to address the issue of wide-wavelength photon harvesting, DSSCs were fabricated by co-adsorbing two complementary dyes SQ-223 and D-131 in various molar ratios. The DSSC fabricated with D-131 and SQ-223 in 9:1 molar ratio displayed the best photovoltaic performance with a PCE of 5.81%, a significantly higher PCE when compared to corresponding individual dye-based DSSCs containing D-131 (3.94%) and SQ-223 (4.67%). Full article

Two of the most significant cases of extant 16th-century featherwork from Mexico are the so-called Moctezuma’s headdress and the Ahuizotl shield. While the feathers used in these artworks exhibit lightfast colors, their assembly comprises mainly organic materials, which makes them extremely fragile. Printed media, including books, catalogs, educational materials, and fine copies, offer an accessible means for audiences to document and disseminate visual aspects of delicate cultural artifacts without risking their integrity. Nevertheless, the singular brightness and iridescent colors of feathers are difficult to communicate to the viewer in printed reproductions when traditional pigments are used. This research explores the use of effect pigments (multilayered reflective structures) and improved halftoning techniques for additive printing, with the objective of enhancing the reproduction of featherwork by capturing its changing color and improving texture representation via a screen printing process. The reproduced images of featherwork exhibit significant perceptual resemblances to the originals, primarily owing to the shared presence of structural coloration. We applied structure-aware halftoning to better represent the textural qualities of feathers without compromising the performance of effect pigments in the screen printing method. Our prints show angle-dependent color, although their gamut is reduced. The novelty of this work lies in the refinement of techniques for printing full-color images by additive printing, which can enhance the 2D representation of the appearance of culturally significant artifacts. Full article

Herein, we evaluate the conversion efficiency of dye-sensitized solar cells (DSSCs) photosensitized using two different natural dyes extracted from Alpinia purpurata and Alstroemeria flower petals. The appreciable absorption capacity of the extracts in the visible light region was examined through absorption spectroscopy. The functional groups of the corresponding pigments were identified through Fourier transform spectroscopy (FTIR) technique thus indicating the presence of cyanidin 3-glycosides and piperine in the flowers of Alstroemeria and Alpinia purpurata. The extracted dyes were immobilized on TiO₂ on transparent conducting FTO glass, which were used as photoanode. The dye-coated TiO₂ photoanode, pt photocathode and iodide/triiodide redox electrolyte assembled into a cell module was illuminated by a light source intensity 100 mW/cm² to measure the photovoltaic conversion efficiency of DSSCs. The TiO₂ anode and Pt counter electrode surface roughness and morphological studies were evaluated using atomic force microscope (AFM) and field emission scanning electron microscopy (FESEM), respectively. Through the photoelectric characterizations, it was promising to verify that the solar conversion efficiency was calculated with the photovoltaic cell sensitized by Alstroemeria and Alpinia purpurata. This was achieved with a yield (η) of 1.74% and 0.65%, with an open-circuit voltage (V_oc) of 0.39 and 0.53 V, short-circuit current density (J_sc) of 2.04 and 0.49 mA/cm², fill factor (FF) of 0.35 and 0.40, and P_max of 0.280 and 0.100 mW/cm², respectively. The results are promising and demonstrate the importance of the search for new natural dyes to be used in organic solar cells for the development of devices that generate electricity in a sustainable way. Full article

This work provides significant insight into the molecular structure of alizarin lake pigments used by artists in the past. To characterize two red powders, lakes 1 and 2, obtained by complexation of 1,2-dihydroxy anthraquinone (alizarin) with Al³⁺_, a multi-analytical approach was designed based on solid and liquid state Nuclear Magnetic Resonance Spectroscopy (NMR), Fourier-Transform Infrared Spectroscopy (FTIR), Mass Spectrometry (MS) and Density Functional Theory (DFT) calculations. Lake 1 was synthesized according to literature and compared with lake 2, a reproduction of an artist’s pigment. FTIR showed Al³⁺ coordinated to oxygens in C1 and C9, and that in lake 2 the -OH groups in C2 are protonated, being responsible for its low solubility. ¹H-NMR proved that lake 2 is formed by two tautomers [Al(Aliz-₂-H-)₂(OH)(H₂O)] and [Al(Aliz-₁₀-H-)₂(OH)(H₂O)], the latter being the major species. SS-NMR was the only technique that got insight into the Al³⁺ coordination, octahedral for both lakes. It confirmed the existence of two species in lake 2, in a 5:1 ratio. Both are amorphous “open structures”, resulting in fewer constraints for the ligands and in a large variety of geometries. SS-NMR allowed the analysis of the red pigments without preparation, which is a unique advantage for their study in artworks. Full article

Derived from malachite green, new triaryl-carbonium-ion-functionalized gold nanoparticles have been synthesized for detecting anions. The detection process, and concomitant colour change, is based on charge compensation on the surface of nanoparticles, which triggers their aggregation, resulting in a bathochromic shift of the plasmon resonance band. The difference in electrophilicity of the malachite green triaryl ions in solution or on gold nanoparticles makes it possible to distinguish different anions related to their nucleophilic character. Full article