Search Results (72)

The superhydrophobic coatings for outdoor use need to be exposed to sunlight for a long time; therefore, their UV-aging resistances are crucial in practical applications. In this study, the primary product of titanium dioxide (P-TiO₂) was used as the raw material. Nano-silica (SiO₂) was coated onto the surface of P-TiO₂ by the acid precipitation method to prepare P-TiO₂-SiO₂ composite particles. Then, they were modified and sprayed simply to obtain a superhydrophobic P-TiO₂-SiO₂/HDTMS coating. The results indicated that amorphous nano-SiO₂ was coated on the P-TiO₂ surface, forming a micro–nano binary structure, which was the essential structure to form superhydrophobic coatings. Additionally, the UV-aging property of P-TiO₂ was significantly enhanced after being coated with SiO₂. After continuous UV irradiation for 30 days, the color difference (ΔE*) and yellowing index (Δb*) values of the coating prepared with P-TiO₂-SiO₂ increased from 0 to 0.75 and 0.23, respectively. In contrast, the ΔE* and Δb* of the coating prepared with P-TiO₂ increased from 0 to 1.68 and 0.74, respectively. It was clear that the yellowing degree of the P-TiO₂-SiO₂ coating was lower than that of P-TiO₂, and its UV-aging resistance was significantly improved. After modification with HDTMS, the P-TiO₂-SiO₂ coating formed a superhydrophobic P-TiO₂-SiO₂/HDTMS coating. The water contact angle (WCA) and water slide angle (WSA) on the surface of the coating were 154.9° and 1.3°, respectively. Furthermore, the coating demonstrated excellent UV-aging resistance. After continuous UV irradiation for 45 days, the WCA on the coating surface remained above 150°. Under the same conditions, the WCAs of the P-TiO₂/HDTMS coating decreased from more than 150° to 15.3°. This indicated that the retention of surface hydrophobicity of the P-TiO₂-SiO₂/HDTMS coating was longer than that of P-TiO₂/HDTMS, and the P-TiO₂-SiO₂/HDTMS coating’s UV-aging resistance was greater. The superhydrophobic P-TiO₂-SiO₂/HDTMS self-cleaning coating reported in this study exhibited outstanding UV-aging resistance, and it had the potential for long-term outdoor use. Full article

The new mineral achyrophanite (K,Na)₃(Fe³⁺,Ti,Al,Mg)₅O₂(AsO₄)₅ was found in high-temperature sublimates of the Arsenatnaya fumarole at the Second scoria cone of the Northern Breakthrough of the Great Tolbachik Fissure Eruption, Tolbachik volcano, Kamchatka, Russia. It is associated with aphthitalite-group sulfates, hematite, alluaudite-group arsenates (badalovite, calciojohillerite, johillerite, nickenichite, hatertite, and khrenovite), ozerovaite, pansnerite, arsenatrotitanite, yurmarinite, svabite, tilasite, katiarsite, yurgensonite, As-bearing sanidine, anhydrite, rutile, cassiterite, and pseudobrookite. Achyrophanite occurs as long-prismatic to acicular or, rarer, tabular crystals up to 0.02 × 0.2 × 1.5 mm, which form parallel, radiating, bush-like, or chaotic aggregates up to 3 mm across. It is transparent, straw-yellow to golden yellow, with strong vitreous luster. The mineral is brittle, with (001) perfect cleavage. D_calc is 3.814 g cm^–3. Achyrophanite is optically biaxial (+), α = 1.823(7), β = 1.840(7), γ = 1.895(7) (589 nm), 2V (meas.) = 60(10)°. Chemical composition (wt.%, electron microprobe) is: Na₂O 3.68, K₂O 9.32, CaO 0.38, MgO 1.37, MnO 0.08, CuO 0.82, ZnO 0.48, Al₂O₃ 2.09, Fe₂O₃ 20.42, SiO₂ 0.12, TiO₂ 7.35, P₂O₅ 0.14, V₂O₅ 0.33, As₂O₅ 51.88, SO₃ 1.04, and total 99.40. The empirical formula calculated based on 22 O apfu is Na_1.29K_2.15Ca_0.07Mg_0.34Mn_0.01Cu_0.11Zn_0.06Al_0.44Fe³⁺_2.77Ti_1.00Si_0.02P_0.02S_0.14V_0.04As_4.90O₂₂. Achyrophanite is orthorhombic, space group P222₁, a = 6.5824(2), b = 13.2488(4), c = 10.7613(3) Å, V = 938.48(5) ų and Z = 2. The strongest reflections of the PXRD pattern [d,Å(I)(hkl)] are 5.615(59)(101), 4.174(42)(022), 3.669(31)(130), 3.148(33)(103), 2.852(43)(141), 2.814(100)(042, 202), 2.689(29)(004), and 2.237(28)(152). The crystal structure of achyrophanite (solved from single-crystal XRD data, R = 4.47%) is unique. It is based on the octahedral-tetrahedral M-T-O pseudo-framework (M = Fe³⁺ with admixed Ti, Al, Mg, Na; T = As⁵⁺). Large-cation A sites (A = K, Na) are located in the channels of the pseudo-framework. The achyrophanite structure can be described as stuffed, with the defect heteropolyhedral pseudo-framework derivative of the orthorhombic Fe³⁺AsO₄ archetype. The mineral is named from the Greek άχυρον, straw, and φαίνομαι, to appear, in allusion to its typical straw-yellow color and long prismatic habit of crystals. Full article

One-dimensional TiO₂ nanotube arrays (TNAs) were vertically aligned and obtained via the electrochemical anodization method. In this study, Bi₂S₃-TiO₂-SiO₂/TNA heterojunction photocatalysts were successfully prepared with different amounts of Bismuth(III) sulfide (Bi₂S₃) loading on the TNAs by the successive ionic layer adsorption and reaction (SILAR) method and characterized by X-ray diffraction (XRD) patterns, field-emission scanning electron microscope–energy-dispersive spectroscopy (FESEM-EDS), Fourier transform infrared (FTIR) spectra, ultraviolet-visible diffuse reflectance spectra (UV–Vis/DRS), and electrochemical impedance spectroscopy (EIS) techniques. The photocatalytic performances of the samples were investigated by degrading Basic Yellow 28 (BY 28) under visible-light irradiation. Optimization of the condition using the response surface methodology (RSM) and central composite rotatable design (CCRD) technique resulted in the degradation of BY 28 dye, showing that the catalyst with 9.6 mg/cm² (designated as Bi₂S_3(9.6)-TiO₂-SiO₂/TNA) showed the maximum yield in the degradation process. The crystallite size of about 17.03 nm was estimated using the Williamson–Hall method. The band gap energies of TiO₂-SiO₂/TNA and Bi₂S_3(9.6)-TiO₂-SiO₂/TNA were determined at 3.27 and 1.87 eV for the direct electronic transitions, respectively. The EIS of the ternary system exhibited the smallest arc diameter, indicating an accelerated charge transfer rate that favors photocatalytic activity. Full article

This study focuses on the nameplate of Vila D. Bosco, a modern building in Macau from the time of Portuguese rule, and looks at the types of metal materials and surface coatings used, as well as how they corrode due to the tropical marine climate affecting the building’s metal parts. The study uses different techniques, such as X-ray fluorescence spectroscopy (XRF), scanning electron microscopy/energy dispersive spectroscopy (SEM-EDS), X-ray diffraction (XRD), attenuated total internal reflectance Fourier transform infrared spectroscopy (ATR-FTIR), and cross-sectional microscopic analysis, to carefully look at the metal, corrosion products, and coating of the nameplate. The results show that (1) the nameplate matrix is a resulfurized steel with a high sulfur content (Fe up to 97.3% and S up to 1.98%), and the sulfur element is evenly distributed inside, which is one of the internal factors that induce corrosion. (2) Rust is composed of polycrystalline iron oxides such as goethite (α-FeOOH), hematite (α-Fe₂O₃), and magnetite (Fe₃O₄) and has typical characteristics of atmospheric oxidation. (3) The white and yellow-green coatings on the nameplate are oil-modified alkyd resin paints, and the color pigments are TiO₂, PbCrO₄, etc. The surface layer of the letters is protected by a polyvinyl alcohol layer. The paint application process leads to differences in the thickness of the paint in different regions, which directly affects the anti-rust performance. The study reveals the deterioration mechanism of resulfurized steel components in a subtropical polluted environment and puts forward repair suggestions that consider both material compatibility and reversibility, providing a reference for the protection practice of modern and contemporary architectural metal heritage in Macau and even in similar geographical environments. Full article

This study explores the photocatalytic efficiency of Zn/Fe/TiO₂ catalysts, synthesized via the wet impregnation method, for degrading the food colorings Allura Red and Tartrazine Yellow. A 2² factorial design with a central point replication guided the catalyst synthesis. Characterization involved BET surface area analysis, SEM-EDX, XRD, and PZC determination. Photocatalytic tests were conducted in batch mode under natural sunlight with 10 mg L⁻¹ food coloring solutions. Kinetic modeling and statistical analysis were performed, and catalyst reuse was evaluated under artificial light. Results showed that low calcination temperatures (200–273 °C) and Zn loadings of 2–10% led to nearly 99% discoloration and degradation efficiency. The Behnajady–Modirshahla–Ghanbery kinetic model best described the discoloration data, confirming the significant impact of both variables. The optimal catalyst for Allura Red degradation was 2%Zn/2%Fe/TiO₂ calcined at 200 °C, while for Tartrazine Yellow, 6%Zn/2%Fe/TiO₂ calcined at 300 °C was most effective. Both catalysts exhibited excellent stability, maintaining efficiency over four reuse cycles. These findings demonstrate the potential of Zn/Fe/TiO₂ catalysts for sustainable wastewater treatment. Full article

In recent years, domestic research on the ion substitution behavior and chromaticity of the mineral composition of “Ya’an Green” remains insufficient, while there is almost no relevant research on “Ya’an Green” abroad. In this study, X-ray powder diffraction (XRD), electron probe microanalysis (EPMA), infrared spectroscopy (IR), ultraviolet–visible spectroscopy (UV-Vis), and colorimetry were employed. The results indicate that the green and yellow matrices of “Ya’an Green” are primarily composed of muscovite, with rutile also present in the yellow matrix. In contrast, the white–green samples are mainly composed of quartz, with muscovite as a secondary mineral. Additionally, it was observed that the (004) crystal plane of muscovite exhibits a peak shift to lower 2θ angles, attributed to the substitution of Al³⁺ by ions with larger radii, such as Ba²⁺, Cr³⁺, and Fe²⁺, leading to an increase in unit cell parameters and a consequent shift in the peak to lower wavenumbers. The main elements of “Ya’an Green” are Al, Si, and K, with minor elements including Na, Fe, and Cr. Furthermore, Mg²⁺, Ca²⁺, Ti⁴⁺, Cr³⁺, and Fe²⁺ in the samples can substitute for Al³⁺ through isomorphic substitution. The infrared spectrum of muscovite in the ‘Ya’an Green’ sample shows three typical absorption peaks, 422 cm⁻¹ and 513 cm⁻¹ caused by Si-O bending vibration, 697 cm⁻¹ and 837 cm⁻¹ caused by Si-O-Al vibration, 948 cm⁻¹ caused by O-H bending vibration, and 3647 cm⁻¹ caused by O-H stretching vibration. The peak at 837 cm⁻¹ exhibits varying degrees of shift due to the substitution of Al³⁺ by ions with larger radii. The ultraviolet–visible spectra display two broad absorption bands at 422 nm and 615 nm, which are caused by Cr³⁺ transition, indicating that Cr is the chromogenic element responsible for the green color. A correlation was observed between the Cr³⁺ content and the hue angle h in “Ya’an Green” samples: the higher the Cr³⁺ content, the closer the hue angle is to 136^°, resulting in a darker green color, while lower Cr³⁺ content leads to a deviation from the dark green hue. This study establishes for the first time the correlation between the mineral composition of ‘Ya’an Green’ and its chromatic parameters and explores the linear relationship between its color and the number of color-causing elements and elemental substitution, which provide data support and theoretical models for the study of the color of seal stones. Full article

This study presents the fabrication and characterization of highly selective, room-temperature gas sensors based on ternary zinc oxide–molybdenum disulfide–titanium dioxide (ZnO-MoS₂-TiO₂) nanoheterostructures. Integrating two-dimensional (2D) MoS₂ with oxide nano materials synergistically combines their unique properties, significantly enhancing gas sensing performance. Comprehensive structural and chemical analyses, including scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), Raman spectroscopy, and Fourier transform infrared spectroscopy (FTIR), confirmed the successful synthesis and composition of the ternary nanoheterostructures. The sensors demonstrated excellent selectivity in detecting low concentrations of nitrogen dioxide (NO₂) among target gases such as ammonia (NH₃), methane (CH₄), and carbon dioxide (CO₂) at room temperature, achieving up to 58% sensitivity at 4 ppm and 6% at 0.1 ppm for NO₂. The prototypes demonstrated outstanding selectivity and a short response time of approximately 0.51 min. The impact of light-assisted enhancement was examined under 1 mW/cm² weak ultraviolet (UV), blue, yellow, and red light-emitting diode (LED) illuminations, with the blue LED proving to deliver the highest sensor responsiveness. These results position ternary ZnO-MoS₂-TiO₂ nanoheterostructures as highly sensitive and selective room-temperature NO₂ gas sensors that are suitable for applications in environmental monitoring, public health, and industrial processes. Full article

This study focused on developing pigmented linear low-density polyethylene (LLDPE) sheets while preserving their mechanical properties and infrared (IR) transparency. Six pigments—ZnO, ZnS, TiO₂, FeO yellow, FeO light brown, and FeO dark brown—were each mixed with polyethylene (PE) wax in a 1:1 ratio and blended with LLDPE at concentrations of 1, 3, and 5 wt%. Tensile strength tests showed minimal changes at lower pigment concentrations, with values near that of pure LLDPE (14 MPa), and slight reductions at 5 wt%. IR transparency tests, conducted using both direct and reflected heat sources, showed that white-pigmented sheets maintained over 85% transparency, while colored pigments exhibited slightly reduced IR transmittance, ranging from 70% to 91%. Fourier Transform Infrared Spectroscopy (FTIR) analysis confirmed that the critical IR transparency range of 8–12 μm remained unaffected with both pure and pigmented sheets. On the other hand, ultraviolet–visible (UV–VIS) testing showed that white-pigmented sheets experienced enhanced visible-light absorption with increasing pigment concentration and thickness, while color-pigmented sheets exhibited high opacity. Additionally, micro-structuring was performed on the LLDPE sheets to further modify their IR properties, which resulted in effective scattering of IR radiation. These findings highlight the potential of pigmented LLDPE sheets for applications requiring both visual opacity and IR transparency, such as thermal management and camouflage, as well as applications requiring tunable IR properties. Full article

Dye-sensitization is a promising strategy to improve the light absorption and photoactivity abilities of wide-bandgap semiconductors, like TiO₂. For effective water-splitting photoanodes with no sacrificial agents, the electrochemical potential of the dye must exceed the thermodynamic threshold needed for the oxygen evolution reaction. This study investigates two promising organic cyanoacrylic dyes, designed to meet that criterion by means of theoretical calculations. Both yellow-colored dyes were synthesized and characterized by optical and photoelectrochemical techniques, demonstrating strong light absorption in the visible region, suitable experimental reduction potentials, and adsorption from the organic solvent onto mesoporous TiO₂ layers. In addition, to promote immobilization in aqueous electrolytes, the dyes were hybridized with graphene oxide or multi-walled carbon nanotubes. Photoelectrochemical analysis of the dye-sensitized photoelectrodes demonstrated efficient charge transfer from the dyes to the TiO₂ photoanode under simulated solar light. While the starting photocurrent notably surpassed the blank TiO₂, a subsequent decay points to kinetic obstacles that still need to be overcome. Full article

Globalization has increased production in various industries, including textiles, food, and pharmaceuticals. These industries employ different dyes in production, leading to undesired discharge, which conventional treatment fails to remove from the water. The present study aims to synthesize, characterize, and use different pure catalysts (TiO₂ and Zn₂SnO₄) and their compounds doped with CoFe₂O₄ together with ozone (O₃) for the degradation of the azo dye yellow tartrazine (TZ), evaluating the process. For this characterization, N₂ porosimeter, zeta potential, X-ray diffraction, SEM-EDS, and diffuse reflectance spectra were used. Specific surface areas (m² g⁻¹) of 109, 106, 65, and 83 were used for TiO₂, CoFe₂O₄/TiO₂, Zn₂SnO₄, and CoFe₂O₄/Zn₂SnO₄, respectively. Both compounds are characterized as nanocatalysts as they have a band gap of 2.75 and 2.83 eV and average particle size of 98 and 85 nm for CoFe₂O₄/TiO₂ and Zn₂SnO₄, respectively. We employed a reactional model, which was able to describe the catalytic ozonation for all cases, with a low R² of 0.9731. The combination of processes increased TZ degradation from 57% to 74% compared to O₃ alone, achieving a maximum degradation of 98.5% within 50 min of catalysis at a low ozone flow rate. This highlights the potential of the produced catalysts for energy-efficient effluent treatment. Full article

One method for the colorimetric detection of hydrogen peroxide vapor is based on a titanium–hydrogen peroxide complex. A color changing material based on a titania hydroxypropyl cellulose thin film was initially developed. However, as this material dries, the sensitivity of the material is significantly reduced. Thus, an alternative sensing material, based on titanium(IV) oxysulfate, an ionic liquid, and in some cases, triflouromethanesulfonic acid adsorbed onto low-cost silicon thin-layer chromatography (TLC) plates, was developed. TiO₂ was heated with concentrated sulfuric acid in a controlled environment, usually at temperatures ranging from 100 °C to 250 °C. These sensors are disposable and single-use and are simple and inexpensive. When the resulting thin-film sensors are exposed to ppm levels of hydrogen peroxide vapor, they turn from a white reflective material to an intense yellow or orange. Ti(IV) oxysulfate combined with an acid catalyst and an ionic-liquid-based material provides an opportunity to enhance the sensor activity towards the peroxide vapor and decreases the detection limit. Kinetic measurements were made by the quantification of the intensity of the reflected light as a function of the exposure time from the sensor in a special cell using a low-cost web camera and a tungsten lamp. The measured rate of the color change indicates high sensitivity and first-order kinetics over a hydrogen peroxide concentration range of approximately 2 to 31 ppm. These new materials are a starting point for the preparation of more active sensor materials for hydrogen peroxide and organic peroxide vapor detection. Full article

This study focused on searching for more effective nanomaterials for environmental remediation and health protection; thus, coliform bacteria, yeast and the organic food dye sunset yellow were selected as target pollutants to be eliminated under solar light by Ag/Cr-TiO₂ and Pd/Cr-TiO₂. Firstly, Cr³⁺ was in situ incorporated into the anatase crystalline lattice by the sol-gel method; then, Ag or Pd nanoparticles were deposited on Cr-TiO₂ by chemical photoreduction. The scientific challenge addressed by the development of these composites was to analyse the recovery of Cr, to be employed in photocatalyst formulation and the enhancement of the TiO₂ photocatalytic activity by addition of other noble metals. By extensive characterization, it was found that after TiO₂ doping with chromium, the parameters of the crystal lattice slightly increased, due to the incorporation of Cr ions into the lattice. The TiO₂ band gap decreased after Cr addition, but an increase in the optical absorptions towards the visible region after noble metals deposition was also observed, which was dependent of the Ag or Pd loading. Generally, it was observed that the noble metals type is a factor that strongly influenced the effectiveness of the photocatalysts concerning each substrate studied. Thus, by using Ag(0.1%)/Cr-TiO₂, the complete elimination of E. coli from samples of water coming from a highly polluted river was achieved. Pd(0.5%)/Cr-TiO₂ showed the highest efficiency in the elimination of S. cerevisiae from a lab prepared strain. On the other hand, the Pd(0.1%)/Cr-TiO₂ sample shows the highest dye degradation rate, achieving 92% of TOC removal after 180 min. Full article

The use of semiconductor materials, specifically TiO₂, for photocatalysis of organic pollutants has gained global interest as an effective method for contaminant removal from wastewater. Titanium dioxide (TiO₂) is a widely studied photocatalyst and is considered one of the best for wastewater treatments due to its high stability, affordability, and nontoxicity. The discharge of wastewater from the textile industries, which constitutes around 20% of total textile effluent, has become a significant environmental concern, posing a threat to both the aquatic ecosystem and human health. We aimed to investigate the photodegradation of organic dyes like Amaranth (AM), Methyl Orange (MO), and Quinoline Yellow (QY), individually and in combination, in an aqueous suspension with varying concentrations of TiO₂. Results indicate a significant degradation of all three dyes in the multicomponent, with approximately 40% degradation in the presence of the 0.050 g/L TiO₂ after 360 min. These findings suggest that TiO₂ has a significant potential as a nanocatalyst in complex matrices. Full article

This study aims to investigate the effects of parent rock and minerals on lateritic weathering. The study presents X-ray diffraction (XRD), whole-rock geochemistry, and Nd-Sr isotopic data for examining two profiles, 10 and 12 m thick, respectively, that illustrate the regional tropical weathering status in the Midwest of Brazil. The profiles, developed from metasedimentary and sedimentary rocks, are constituted by saprolite, mottled horizon, lateritic duricrust, and oxisol. Across the profiles, the minerals controlling the weathering geochemistry are muscovite, microcline, quartz, kaolinite, hematite, goethite, and gibbsite. Red and yellow zones in the saprolite and mottled horizon as well as the lateritic duricrust with breccia/fragmental, pisolitic, and oolitic textures make profile 1 more complex. In contrast, profile 2 has an oxisol that mantles the homogeneous vermiform lateritic duricrust. Fe₂O₃, accumulated during surface weathering, is a potent element in the geochemical profile control since it forms the harder goethite to hematite lateritic duricrust, bearing most of the trace elements (As, Cu, Cs, Pb, Sc, Sr, Th, U, V, and Zn) with similar ionic radii and electrovalence. The LREE have affinity for the elements of the Fe₂O₃ group of the lateritic duricrust. On the other hand, the K₂O group together with Zr and TiO₂ e in the phyllite, saprolite, and mottled horizon of profile 1, are associated with the HREE. Additionally, in profile 2, the HREE are mostly associated with the Al₂O₃ group and the residual minerals in the oxisol. The indication that REE is associated with phosphates, zircon, rutile/anatase, cereanite, and muscovite/illite, which have variable weathering behavior, caused the REE fractionation to occur across and between the profiles. Despite the REE fractionation, the Ɛ_Nd(0) values along the profiles consistently maintain the signature of the parent rock. Muscovite and microcline weathering, in profiles 1 and 2, respectively, control the decrease in ⁸⁷Sr/⁸⁶Sr signatures of both profiles and the distinct radiogenic ratios. The development of lateritic duricrust in both profiles indicates a similar weathering intensity, although the gibbsite–kaolinite predominance in the oxisol of profile 2 highlights a geochemical reorganization under humid conditions, as well as near-intense soluble silica leaching. Full article

Blue sapphire has long been treated with heat to modify its blue color and attain greater value. However, the process of modifying the blue color in sapphire remains not well understood. The color-changing mechanism has traditionally been explained using the Intervalence Charge Transfer (IVCT) (Fe²⁺-Ti⁴⁺ and/or Fe²⁺-Fe³⁺) theory, wherein the blue color can be diminished by heat treatment in an oxidizing environment which alters Fe²⁺ (FeO) to Fe³⁺ (Fe₂O₃) and decreases the occurrence of the IVCT process. However, recently, the band gap theory has been proposed, suggesting that iron (Fe) in sapphire is always in the Fe³⁺ state, the blue color is caused by Fe³⁺-Ti⁴⁺ pair and the heat treatment does not affect Fe oxidation state. Therefore, in this study, eight magmatic sapphires from four localities were investigated for changes in blue color via color analysis, changes in spectra using XANES, and changes in chemical composition using PIXE both before and after heat treatment. The color analysis reveals a slight reduction in saturation (fading of blue) and a noticeable lightening after heat treatment, which corresponds with the high content of solid inclusions or trapiche samples. XANES data analysis using the LCF technique indicated insignificant changes in Fe oxidation state from 2+ to 3+ after heat treatment across all samples. However, when comparing the XANES data with color parameter L*a*b*, it is noted that the percentage of Fe oxidation state changes does not show a positive relationship with changes in blue based on color parameter b* (blue–yellow); rather, it shows a positive relationship with parameter L* (lightness). Microscopic observations also reveal the dissolution of clouds or minute particles around planes of ilmenite needles. It could be suggested that the changes in Fe oxidation state may not be directly related to changes in blue color but could be linked to the partial dissolution of Fe-bearing inclusions. Full article