Search Results (42)

The present study examined the drying kinetics of two-phase olive pomace (OP) using near-infrared (NIR) thin layer intermittent drying at 70–140 °C. For the first time, this approach was combined with color, bioactive compound retention and antioxidant activity assessment. Among tested models, the Midilli’s semi-empirical model best described the drying behavior (r² ≥ 0.99839, RMSE ≤ 0.01349). Effective diffusivity ranged from 1.417 × 10⁻⁹ to 5.807 × 10⁻⁹ m²/s, and activation energy was calculated at 23.732 kJ/mol. Drying at 140 °C reduced time by 68% compared to 70 °C. The corresponding sample had the highest total phenolics content, antioxidant activity (DPPH^●, CUPRAC assays) and triterpenic acid (maslinic, oleanolic) content, and a significant amount of hydroxytyrosol, despite the increased sample browning. Compared to oven-drying (140 °C), NIR was equal or better and 3.2-fold faster. The same was evidenced compared to freeze-drying, except for tyrosol recovery (1.2-fold lower in NIR). These findings were obtained using two different OP industrial samples. Given that NIR is already used industrially for food drying, the present study offers proof-of-concept for its application as a rapid and eco-friendly pretreatment of OP for food and feed uses. However, scalability challenges and the limitations of semi-empirical modeling must be addressed in the future to support industrial-scale implementation. Full article

Olive oil extraction by two-phase systems generates a by-product called “alperujo” which presents several difficulties for its valorization. The present work evaluated an industrial approach, based on the application of thermal treatments to alperujo followed by solid/liquid separation using standard two-phase olive oil mill equipment. Treatments consisted of the thermo-malaxation of alperujo at 70 °C for 45 or 90 min, with or without acid addition, followed by solid/liquid separation in an industrial decanter. The solid was characterized concerning subsequent use for composting, while total and hydrophilic phenolics were analyzed in liquid for their recovery. Additionally, a laboratory-scale trial to compare phenolic purification by ethylic acetate extraction with chromatographic procedures was also included. The static respiration index showed that solid fractions presented higher susceptibility to biodegradation processes than raw alperujo. The phenolic content of treated liquid fractions was higher than in raw alperujo. Total phenolics were maximum at the longest exposure time without acid addition, while hydrophilic phenolics were highest at the shortest exposure time in acidified samples. The use of non-ionic resins seemed attractive for obtaining highly concentrated phenolic fractions. The proposed thermal treatments can be applied in olive oil industries, allowing in situ pomace valorization and the recovery of phenolic-enriched liquid fractions. Full article

Hydrothermal carbonization (HTC) is a promising method for the conversion of agricultural and agro-industrial residues into valuable products. HTC processes biomass through chemical reactions that produce hydrochar, a carbon-rich solid similar to lignite. Unlike other thermochemical processes, HTC can handle high-moisture biomass without pre-drying. This article evaluates the efficiency of HTC on wood chips, wheat straw, and grape pomace, examining their chemical and structural characteristics and critical operational parameters such as the temperature, pressure, biomass/water ratio, and reaction time. The obtained results highlight that the two key process parameters are the temperature and the ratio between the solid biomass and liquid phase. Increasing the first parameter increases the energy content by 20% and increases the carbon concentration by up to 50%, while reducing the oxygen content by 30% in the hydrochar. Varying the second parameter leads to the alternating reduction of the ash content but simultaneously reduces the energy content. The reaction time seems to have a limited influence on the quality parameters of the biochar produced. Lastly, HTC appears to successfully enhance the overall quality of widely available agricultural wastes, such as grape pomace. Full article

The present study aims to resolve the existing research gaps on olive pomace (OP) hydrochars application as a fuel by evaluating its molecular structures (FTIR and solid NMR analysis), identifying influential characteristics (Pearson correlation analysis), process optimization (response surface methodology), slagging–fouling risks (empirical indices), and combustion performance (TG-DSC analysis). The response surfaces plot for hydrothermal carbonization (HTC) of OP slurry performed in a pressure reactor under varied temperatures (180–250 °C) and residence times (2–30 min) revealed 250 °C for 30 min to be optimal conditions for producing hydrochar fuel with a higher heating value (32.20 MJ·Kg⁻¹) and energy densification ratio (1.40). However, in terms of process efficiency and cost-effectiveness, the optimal HTC conditions for producing the hydrochar with the highest energy yield of 87.9% were 202.7 °C and 2.0 min. The molecular structure of hydrochar was mainly comprised of aromatic rings with methyl groups, alpha-C atoms of esters, and ether bond linkages of lignin fractions. The slagging and fouling risks of hydrochars were comparatively lower than those of raw OP, as indicated by low slagging and fouling indices. The Pearson correlation analysis emphasized that the enrichment of acid-insoluble lignin and extractive contents, carbon densification, and reduced ash content were the main pivotal factors for hydrochar to exhibit better biofuel characteristics for energy applications. Full article

At present, taking into account the sustainability of the starting matrices, the biogas production industry is continuously growing, especially in consideration of ecological transition and circularity. The present study deals with the development of anaerobic bioreactors aimed at valorizing two specific wastes of the olive oil supply chain, i.e., the residual of protein hydrolysis process of three-phases olive pomace (OP-PH) and that recovered after the extraction of bioactive molecules from olive mill wastewater (OMWW waste). The energy consumed for biogas production varied from 0.52 kJ (OP and OMWW waste) to 0.97 kJ (OP-PH), while the energy produced for OP, OP-PH and OMMW waste was equal to 1.73, 2.94 and 1.60 kJ, respectively. The optimal production period was defined by considering only the range showing energy production higher than its consumption. According to this, OMWW showed the best performances, since it required 9 days (instead of 12 of untreated and treated OP) to reach the completion. The biogas production efficiency of the three-phase OP-PH waste calculated in the optimal production period, i.e., 12 days, was higher than the other samples, with a yield of 76.7% and a quantity of energy potentially producible corresponding to 1727.8 kJ/kg of volatile solids. These results pave the way for possible applications of this procedure for the planning of a multi-purpose biorefinery fed with by-products from the olive supply chain waste, thus promoting the use of sustainable waste materials from a circular economy perspective. Full article

Two-phase olive pomace is a byproduct of the olive-oil extraction process that is sometimes processed further to recover more oil. During pomace oil production, especially in the early stages of olive processing, odours can be produced. These odours are a serious nuisance, especially in and around the processing facilities, as well as for nearby communities. These odours can be strong and unpleasant, and they may result in various issues, including environmental concerns. Thus, in this paper, the effect of storage and drying on the composition of two-phase olive pomace was investigated. Several physicochemical and instrumental analyses were performed, and it was concluded that the structural elements of pomace are not the ones that are affected during storage and drying. Storage and drying mainly impact the oil content of pomace, leading to an acidity increase and to the production of odorous oxidation compounds. Volatile acids, methyl, and ethyl esters are released into the atmosphere, thus causing serious environmental nuisance. Full article

As a by-product of pomegranate processing, the recycling and reuse of pomegranate pomaces (PPs) were crucial to environmentally sustainable development. Ultrasound-assisted aqueous two-phase extraction (UA-ATPE) was applied to extract the anthocyanins (ACNs) from PPs in this study, and the central composite design response surface methodology (CCD-RSM) and artificial neural network–genetic algorithm (ANN-GA) models were utilized to optimize the extraction parameters and achieve the best yield. The results indicated that the ANN-GA model built for the ACN yield had a greater degree of fit and accuracy than the RSM model. The ideal model process parameters were optimized to have a liquid–solid ratio of 49.0 mL/g, an ethanol concentration of 28 g/100 g, an ultrasonic time of 27 min, and an ultrasonic power of 330 W, with a maximum value of 86.98% for the anticipated ACN yield. The experimental maximum value was 87.82%, which was within the 95% confidence interval. A total of six ACNs from PPs were identified by utilizing UHPLC-ESI-HRMS/MS, with the maximum content of cyanidin-3-O-glucoside being 57.01 ± 1.36 mg/g DW. Therefore, this study has positive significance for exploring the potential value of more by-products and obtaining good ecological and economic benefits in the future. Full article

Red wine contains polyphenols which are extracted during the winemaking process. However, winemaking is not an extraction; therefore, the resulting byproducts still have a substantial polyphenol content. The aim of this study was to compare two methods for the extraction of phenolic compounds: maceration and matrix solid-phase dispersion (MSPD). Grape pomace (Vitis vinifera var. Cabernet Sauvignon) from a winery in Querétaro, Mexico was used. The optimal conditions for both methods were identified. Phenolic compounds and antioxidant activity were the response variables. A central composite design was used (Minitab 17) for the extraction by maceration. The maceration time (1, 4, 12, 20, and 24 h) and the ratio of ethanol (50 to 80%) acidified with 1% HCl were the two factors studied. For the MSPD extraction, sea sand was used as a dispersant, and a 2² factorial design was employed for the evaluation, with the elution volume and the ratio of sample/dispersant being the two factors analyzed. The optimal extraction method was MSPD with 96 mL (acidified ethanol) as the elution volume and a 1:2 ratio of sample/dispersant. Using these conditions, 14.01 ± 0.19 mMol TEAC/100 g db (Trolox equivalent of antioxidant capacity) of grape pomace was obtained, whereas the total phenolic content was 2836.73 ± 41.90 mg GAE/100 g db. These values are greater than those obtained by maceration. These conditions are close to those predicted by the model (analysis of variance (ANOVA) with a level of significance of 5% (p < 0.05) and a Tukey comparison test for determining significant differences in the comparison of results). Full article

Mediterranean agriculture asks for sustainable strategies to prevent actual soil organic matter decline rates. Composting agri-food by-products for application in farmland, besides contributing to a circular economy at regional or local scales, may improve soil resistance to physical degradation. Aggregate stability (AS) is a crucial property for building up such resistance. Olive pomace is an abundant by-product of the olive oil industry that may be valorized through composting. This study aimed to assess the influence on AS of olive-pomace-based composts (OPC) applied to a sandy loam Leptosol and a clay loam Fluvisol. To assess the effects of compost characteristics on AS, three OPCs resulting from different olive pomace proportions in the composting raw material (44, 31, and 25% by volume) were applied to aggregate samples in three doses (10, 20, and 40 t.ha⁻¹, plus control) with fine and coarse grain sizes. Controlled laboratory conditions subjected samples to daily wetting-drying cycles during a 30-day experiment. AS was measured by wet sieving. OPC application significantly increased AS in the Leptosol amended with fine (+15% vs. control) and coarse (+19%) grain-size compost. In well-aggregated Fluvisol, amendment induced a significant increase in AS only in the compost coarse grain size (+12%). The application dose significantly affected AS, with 10 t.ha⁻¹ being the best-performing dose. OPC applications in weakly aggregated soils are seemingly an encouraging soil management practice for improving soil resistance to physical degradation and reducing soil organic matter decline rates in Mediterranean farmland. Full article

The use of a two-phase decanter (TwPD) for olive-oil extraction produces wastes and byproducts (a small volume of water from oil washing, olive leaves from the defoliator, and a high moisture pomace which can be destoned) that contain valuable bioactive compounds, such as phenolics and/or triterpenic acids. So far, there is no (water) or limited information (leaves and the destoned pomace fraction) on their content of bioactives, especially triterpenic acids. To contribute to the characterization of such streams from cultivars of international interest, in the present study, samples obtained from five mills from the region of Laconia (from one or two harvests) in Greece, where Koroneiki cv dominates, were screened for phenols and/or triterpenic acids. The leaves and pomace were dried at two temperatures (70 °C and/or 140 °C), and the pomace was also destoned before analysis. The liquid wastes contained low amounts of total (TPC) phenols (<140 mg gallic acid/L), hydroxytyrosol (<44 mg/L), and tyrosol (<33 mg/L). The olive leaves varied widely in TPC (12.8–57.4 mg gallic acid/g dry leaf) and oleuropein (0.4–56.8 mg/g dry leaf) but contained an appreciable amount of triterpenic acids, mainly oleanolic acid (~12.5–31 mg/g dry leaf, respectively). A higher drying temperature (140 vs. 70 °C) affected rather positively the TPC/oleuropein content, whereas triterpenic acids were unaffected. The destoned pomace TPC was 15.5–22.0 mg gallic acid/g dw, hydroxytyrosol 3.9–5.6 mg/g dw, and maslinic 5.5–19.3 mg/g dw. Drying at 140 °C preserved better its bioactive phenols, whereas triterpenic acids were not influenced. The present findings indicate that TwPD streams may have a prospect as a source of bioactives for added-value applications. Material handling, including drying conditions, may be critical but only for phenols. Full article

The pomace olive oil sector needs to improve its use of the main olive oil by-product, called alperujo, which is currently used mainly for combustion after extraction of pomace oil, with all the problems this process entails due to the high degree of humidity, organic load and phytotoxic substances. In this work, a solution at an industrial level that uses thermo-malaxation at a temperature close to 65 °C for one or two hours followed by centrifugation in three phases is proposed. In this way, over 40% of the pomace oil that is rich in minor compounds, a solid with a lower degree of humidity (55%), and a liquid aqueous fraction that is rich in bioactive compounds such as phenolics and sugars are obtained. This aqueous fraction can be treated through subsequent storage stages to increase its content of the main phenolic, hydroxytyrosol, to up to 1.77 g/L, decreasing its percentage of insoluble solids by up to 1.9%, making it possible to obtain extracts that are rich in hydroxytyrosol using systems that are commonly in place at the industrial level. The aqueous fraction, without phenolics, could be used for energy production. A solid with a slightly higher fat content than the initial alperujo remains, thus the rest of the oil content can be extracted from it using solvent, making it, once defatted, suitable for application in subsequent bioprocesses. Full article

The wine industry produces large amounts of grape pomace (GP), a waste that needs to be disposed of properly. Bioactive compounds with high added value can be recovered from GP as an interesting strategy to reduce the environmental impact. Here, two different technologies were employed to recover polyphenol compounds from GP: microwave hydrodiffusion and gravity (MHG) and ultrasound-assisted extraction (UAE). The further purification of UAE and MHG extracts was carried out through solid-phase extraction (SPE) to obtain three fractions, F1, F2 and F3. ATR-FTIR analysis confirmed the presence of sugar and polysaccharide components in F1, as well as non-anthocyanin and anthocyanin compounds in F2 and F3, respectively. Also, the chemical profile was determined by HPLC-UV-DAD, identifying the presence of catechin in F2, and malvidin-3-O-glucoside chloride and cyanidin chloride derivative as the main anthocyanin compounds in F3. The fractions and their parental extracts were characterized for total phenolic content (TPC) and scavenger activity by in vitro assays. We found that F2-MHG and F3-MHG contained phenol contents 6.5 and 8.5 times higher than those of the parental non-fractionated extracts. Finally, F3-MHG (100 μg/mL, w/v) was shown to reduce the proliferation of HT-29 cells. Full article

Italian grape ale (IGA) beers have been categorized by the Beer Judge Certification Program as a sub-category of fruit beers in which grape, or grape must, is added during the brewing process to provide additional characteristics to the final beer. In the present work, IGA beers have been produced with must and pomace of the Malvasia di Candia Aromatica (MaCA) grape variety, which were added before fermentation at two different percentages (10% and 20%). The (poly)phenolic profile of IGA beers have been characterized with HPLC-MS/MS and compared to a golden ale control beer (produced in the same conditions without the addition of grape-derived ingredients). A series of sub-samples have been collected to monitor the (poly)phenol profile at time 0 and during the different phases of the fermentation process (1, 3, 5, 7 30, 65 days). Results demonstrated how the addition of pomace allowed to significantly enrich (p < 0.05) final beers in total (poly)phenols detected by MS, while must addition did not influence that amount if compared to the control sample. However, a PCA cluster analysis identified strong similarities among IGA beers and differentiated them to control beer samples. This study underlined how the addition of must and pomace from the MaCA grape variety improved the (poly)phenolic profile of beer from both a qualitative and quantitative point of view. Full article

The beneficial health effect of red wine depends on its phenolic content and the phenolic content in red wines is affected by ecological, agricultural, and enological practices. Enriched wines have been proposed as an alternative to increase the phenolic content in wines. Nevertheless, phenolic compounds are related to the sensory characteristics of red wines, so enrichment of red wines requires a balance between phenolic content and sensory characteristics. In the present study, a Merlot red wine was enriched with a phenolic extract obtained from Cabernet Sauvignon grape pomace. Two levels of enrichment were evaluated: 4 and 8 g/L of total phenolic content (gallic acid equivalents, GAE). Wines were evaluated by a trained panel to determine their sensory profile (olfactive, visual, taste, and mouthfeel phases). The bioaccessibility of phenolic compounds from enriched red wines was evaluated using an in vitro digestive model and phenolic compounds were quantified by High Performance Liquid Chromatography coupled to tandem mass spectrometry (HPLC-MS/MS). Enrichment increased mainly flavonols and procyanidins. Such an increase impacted astringency and sweetness perceived by judges. This study proposes an alternative to increase the phenolic content in wines without modifying other main sensory characteristics and offers a potential beneficial effect on the health of consumers. Full article

Climate change and compostinS1g methods have an important junction on the phenological and ripening grapevine phases. Moreover, the optimization of these composting methods in closed-loop corporate chains can skillfully address the waste problem (pomace, stalks, and pruning residues) in viticultural areas. Owing to the ongoing global warming, in many wine-growing regions, there has been unbalanced ripening, with tricky harvests. Excessive temperatures in fact impoverish the anthocyanin amount of the must while the serious water deficits do not allow a correct development of the berry, stopping its growth processes. This experiment was created to improve the soil management and the quality of the grapes, through the application of a new land conditioner (Zeowine) to the soil, derived from the compost processes of industrial wine, waste, and zeolite. Three treatments on a Sangiovese vineyard were conducted: Zeowine (ZW) (30 tons per ha), Zeolite (Z) (10 tons per ha), and Compost (C) (20 tons per ha). During the two seasons (2021–2022), measurements were made of single-leaf gas exchange and leaf midday water potential, as well as chlorophyll fluorescence. In addition, the parameters of plant yield, yeast assimilable nitrogen, technological maturity, fractionation of anthocyanins (Cyanidin-3-glucoside, Delphinidin-3-glucoside, Malvidin-3-acetylglucoside, Malvidin-3-cumarylglucoside, Malvidin-3-glucoside, Peonidin-3-acetylglucoside, Peonidin-3-cumarylglucoside, Peonidin-3-glucoside, and Petunidin-3-glucoside), Caffeic Acid, Coumaric Acid, Gallic Acid, Ferulic Acid, Kaempferol-3-O-glucoside, Quercetin-3-O-rutinoside, Quercetin-3-O-glucoside, Quercetin-3-O-galactoside, and Quercetin-3-O-glucuronide were analyzed. The Zeowine and zeolite showed less negative water potential, higher photosynthesis, and lower leaf temperature. Furthermore, they showed higher levels of anthocyanin accumulation and a lower level of quercetin. Finally, the interaction of the beneficial results of Zeowine (soil and grapevines) was evidenced by the embellishment of the nutritional and water efficiency, the minimizing of the need for fertilizers, the closure of the production cycle of waste material from the supply chain, and the improvement of the quality of the wines. Full article