Search Results (16)

Aim: This in vitro study aimed to evaluate the adhesive performance of zirconia and lithium disilicate Maryland cantilever restorations on prepared and non-prepared anterior abutment teeth. While conventional clinical protocols involve abutment tooth preparation, no-preparation (no-prep) restorations have emerged as a viable, minimally invasive alternative. This study compared the adhesion fracture resistance (N) of zirconia restorations on non-prepared enamel surfaces with those on prepared surfaces exposing the dentin. Additionally, the zirconia restorations were compared with lithium disilicate Maryland cantilever restorations, a more common yet costly alternative. Materials and Methods: Forty extracted anterior teeth were allocated into four groups based on preparation type (prepared vs. non-prepared) and material (zirconia vs. lithium disilicate). Each group received cantilevered single-unit FPDs fabricated via CAD/CAM and adhesively cemented using Variolink^® Esthetic DC. Standardized loading was applied using a universal testing machine, and the fracture resistance was recorded. Results: The fracture resistance ranged from 190 to 447 N in the zirconia groups and from 219 to 412 N in the lithium disilicate groups. When comparing all the zirconia versus all the lithium disilicate ceramic restorations, regardless of tooth preparation, no statistically significant difference was found (p = 0.752). However, the non-prepared restorations exhibited significantly higher fracture resistance than their prepared counterparts (p = 0.004 for zirconia; p = 0.012 for lithium disilicate ceramic). All the failures were attributed to tooth fracture, except one zirconia restoration, with no debonding observed. Conclusions: Both zirconia and lithium disilicate Maryland cantilever restorations demonstrated reliable adhesive performance when bonded using appropriate surface conditioning and adhesive protocols. Interestingly, the non-prepared designs exhibited higher fracture resistance than the prepared abutments, highlighting their potential advantage in minimally invasive restorative dentistry. Zirconia Maryland bridges, in particular, represent a cost-effective and mechanically resilient option for anterior single-tooth replacement. Full article

Labyrinth seals, extensively used in aerospace and turbomachinery as non-contact sealing devices, undergo accelerated wear and enhanced leakage due to repeated rub-impact between rotating shafts and sealing rings. To address the problem of increased leakage under rub-impact conditions, this research integrates experimental and numerical methods to investigate the deformation mechanisms and leakage characteristics of thermoplastic labyrinth seals. A custom designed rub-impact test rig was constructed to measure dynamic forces and validate finite element analysis (FEA) models with an error of 5.1% in predicting tooth height under mild interference (0.25 mm). Computational fluid dynamics (CFD) simulations further demonstrated that thermoplastic materials, such as PAI and PEEK, displayed superior resilience (with rebound ratios of 57% and 70.3%, respectively). Their post-impact clearances were 4.8–18.3% smaller than those of PTFE and F500. Leakage rates were predominantly correlated with interference, causing a substantial increase compared to the original state; at 0.25 mm interference (reverse flow), increases ranged from 151% (PAI) to 217% (PTFE), highlighting material-dependent performance degradation. Meanwhile, tooth orientation modulated leakage by 0.5–3% through the vena contracta effect. Based on these insights, two optimized inclined-tooth geometries were designed, reducing leakage by 28.2% (Opt1) and 28.1% (Opt2) under rub-impact. These findings contribute to the development of high-performance labyrinth seals suitable for extreme operational environments. Full article

Background/Objectives: In the oral environment, tooth-colored restorations are frequently exposed to staining agents, affecting their aesthetic and physical properties. This study assessed the impact of stains and bleaching agents on the surface roughness, microhardness, and color stability of four different composite materials (Omnichroma, Charisma, Z350, and TPH). Methods: Based on group distribution, the discs of all the composite material samples were prepared. All the ninety-six-disc specimens (n = 96) were then randomly divided into four different groups based on different composite resin groups. The samples were then immersed into four different immersing media [each group had twenty-four-disc samples (n = 24)]. Finally, all the samples then faced the challenge of a bleaching agent application. Measurements were taken at baseline, post-immersion, and post-bleaching stages. Results: Red wine caused increased roughness in Filtek™ Z350 and significant color change in Omnichroma, while coffee increased roughness in Omnichroma and altered the color of TPH spectra. Soda led to increased roughness and significant color change in TPH spectra. Additionally, Filtek™ Z350 experienced reduced microhardness across all solutions after bleaching. Conclusion: This study concluded that staining and bleaching adversely affected the tested composites, with increases in surface roughness, color change, and microhardness reduction observed. Overall, Charisma diamond demonstrated the greatest resilience to staining and bleaching challenges, whereas Filtek™ Z350 XT exhibited the most pronounced degradation, indicating that composite formulation critically governs both aesthetic and mechanical stability under clinically relevant conditions. Full article

The identification of human remains is a major challenge in forensic science, particularly in cases of advanced decomposition. Human teeth are among the most resilient tissues to environmental and post-mortem degradation, making them a valuable source of DNA for forensic identification. However, DNA preservation in teeth is influenced by multiple factors that can compromise the success of genetic analysis. Objective: This review analyzes the intrinsic and extrinsic factors affecting DNA preservation in human teeth, focusing on ante-mortem and post-mortem variables rather than the methodological aspects of DNA extraction and analysis. Methodology: A review of the literature was conducted, evaluating studies that assess the impact of biological factors (such as dental structure, pathology, and treatment) and environmental conditions (such as burial environment, temperature, and humidity) on DNA degradation in human teeth. Results: The findings indicate that DNA preservation is significantly influenced by the type of tooth, the presence of dental restorations or pathological conditions, and exposure to environmental factors. While some studies address these variables individually, forensic cases often involve complex interactions among multiple factors, making DNA recovery outcomes unpredictable. Conclusions: The degradation of DNA in human teeth results from a multifactorial process where intrinsic and extrinsic elements interact dynamically. A comprehensive understanding of these factors is essential for optimizing sampling strategies and improving DNA recovery success rates in forensic applications. Future research should aim to develop predictive models that account for these variables, enabling more effective case-specific approaches to forensic DNA analysis. Full article

Background. The impact of tongue protrusion forces on the formation of malocclusions is well documented in academic literature. In the case of bone dehiscence of the buccal wall in front of the lower frontal teeth, this process may be even more pronounced. Augmentation with 3D customized allogenic bone blocks (CABB) has been proposed as a potential solution for treating such defects. The objective was to assess the impact of bone block adjustment accuracy on the resistance of teeth to protrusion forces at various stages of alveolar bone loss. Methods: A finite element analysis (FEM) was conducted to ascertain whether augmentation with a CABB will result in increased resilience to tongue protrusion forces. Three-dimensional models of the mandible with dehiscenses were created, based on the dehiscences classification and modification proposed in the journal by the authors of regenerative method. The models feature a CABB positioned at three different distances: 0.1 mm, 0.4 mm, and 1.0 mm. The material parameters were as follows: bone (homogenous, isotropic, E = 2 GPa), teeth (E = 20 GPa), periodontal ligament (E = 0.44 MPa), and membrane between bones (E = 3.4 MPa). A tongue protrusion force within the range of 0–5 N was applied to each individual frontal tooth. Results: The use of an CABB has been shown to positively impact the stability of the teeth. The closer the bone block was placed to the alveolar bone, the more stable was the result. The best results were obtained with a ¼ dehiscence and 0.1 mm distance. Conclusions: The protrusive forces produced by the tongue might not be the biggest one, but in a presence of the bone loss they might have serious results. Even shortly after the surgery, CABB has a positive impact on the incisor resilience. Full article

This article introduces an improved deep learning network, GRU-Net, designed to facilitate direct and precise phase unwrapping of wrapped phase measurements in gear tooth surface interferometry. GRU-Net incorporates a Gram matrix within each down-sampling process to compute style loss, thereby capturing essential stripe structure information features. This network exhibits enhanced capability in handling larger and more intricate gear tooth interferograms, particularly in scenarios involving pronounced noise and aliasing, while still yielding favorable outcomes. A comparative evaluation was conducted, contrasting GRU-Net with the Res-UNet network and other conventional methods. The results demonstrate that GRU-Net surpasses the alternative approaches in terms of unwrapping accuracy, noise resilience, and anti-aliasing capabilities, with accuracy improved by at least 24%, exhibiting significantly superior performance. Additionally, in contrast to the Res-UNet network, GRU-Net demonstrates accelerated learning speed and generates more compact models. Full article

The aim of this paper was to evaluate the fracture resistance of 3D-printed zirconia occlusal veneers (OVs) of different thicknesses and supported by different abutment materials. Materials and Methods: The standard OV of a natural molar was prepared and digitized using a laboratory 3D scanner. The resulting digital tooth abutment was milled either using cobalt–chromium (CoCr) or a fiber-reinforced composite (FRC). All the abutments were digitized and standardized OVs (30° tilt of all the cusps) designed with 0.4 mm, 0.6 mm, or 0.8 mm wall thicknesses. The OVs were fabricated using either the Programill PM7 milling device (Ivoclar Vivadent, PM) or one of two 3D zirconia printers, Cerafab 7500 (Lithoz, LC) or Zipro-D (AON, ZD). The ZD samples were only tested on CoCr abutments. The completed OVs were luted to their abutments and subjected to artificial aging, consisting of thermocycling and chewing simulation before fracture testing with a steel sphere (d = 8 mm) as an antagonist with three contact points on the occlusal OV surface. Besides the total fracture resistance F_u,tot, the lowest contact force F_u,cont leading to the local fracture of a cusp was of interest. The possible effects of the factors fabrication approach, wall thickness, and abutment material were evaluated using ANOVA (α = 0.05; SPSS Ver.28). Results: The total fracture resistance/contact forces leading to failure ranged from F_u,tot = 416 ± 83 N/F_u,cont = 140 ± 22 N for the 0.4 mm OVs fabricated using LC placed on the FRC abutments to F_u,tot = 3309 ± 394 N (ZD)/F_u,cont = 1206 ± 184 N (PM) for the 0.8 mm thick OVs on the CoCr abutments. All the factors (the fabrication approach, abutment material, and OV wall thickness) had an independent effect on F_u,tot as well as F_u,cont (p < 0.032). In pairwise comparisons for F_u,tot of the OVs luted to the CoCr abutments, the ZD samples statistically outperformed the LC- and PM-fabricated teeth irrespective of the thickness (p < 0.001). Conclusions: Within the limitations of this study, the printed occlusal veneers exhibited comparable fracture resistances to those of the milled variants. However, more resilient abutments (FRC as a simulation of dentine) as well as a thinner wall thickness led to reduced OV fracture resistance, suggesting that 0.4 mm thick zirconia OVs should not be unreservedly used in every clinical situation. Full article

The efficacy of retainers is a pivotal concern in orthodontic care. This study examined the biomechanical behaviour of retainers, particularly the influence of retainer stiffness and tooth resilience on force transmission and stress distribution. To do this, a finite element model was created of the lower jaw from the left to the right canine with a retainer attached on the oral side. Three levels of tooth resilience and variable retainer bending stiffness (influenced by retainer type, retainer diameter, and retainer material) were simulated. Applying axial or oblique (45° tilt) loads on a central incisor, the force transmission increased from 2% to 65% with increasing tooth resilience and retainer stiffness. Additionally, a smaller retainer diameter reduced the uniformity of the stress distribution in the bonding interfaces, causing concentrated stress peaks within a small field of the bonding area. An increase in retainer stiffness and in tooth resilience as well as a more oblique load direction all lead to higher overall stress in the adhesive bonding area associated with a higher risk of retainer bonding failure. Therefore, it might be recommended to avoid the use of retainers that are excessively stiff, especially in cases with high tooth resilience. Full article

Lithium disilicate (LDS) glass ceramics are among the most common biomaterials in conservative dentistry and prosthodontics, and their wear behavior is of paramount clinical interest. An innovative in vitro model is presented, which employs CAD/CAM technology to simulate the periodontal ligament and alveolar bone. The model aims to evaluate the effect of the abutment rigidity on the wear resistance of the LDS glass ceramic. Two experimental groups (LDS restorations supported by dental implants, named LDS-on-Implant, or by hybrid ceramic tooth replicas with artificial periodontal ligament, named LDS-on-Tooth-Replica) and a control group (LDS-Cylinders) were compared. Fifteen samples (n = 15) were fabricated for each group and subjected to testing, with LDS antagonistic cusps opposing them over 120,000 cycles using a dual axis chewing simulator. Wear resistance was analyzed by measuring the vertical wear depth (mm) and the volume loss (mm³) on each LDS sample, as well as the linear antagonist wear (mm) on LDS cusps. Mean values were calculated for LDS-Cylinders (0.186 mm, 0.322 mm³, 0.220 mm, respectively), LDS-on-Implant (0.128 mm, 0.166 mm³, 0.199 mm, respectively), and LDS-on-Tooth-Replica (0.098 mm, 0.107 mm³, 0.172 mm, respectively) and compared using one-way-ANOVA and Tukey’s tests. The level of significance was set at 0.05 in all tests. Wear facets were inspected under a scanning electron microscope. Data analysis revealed that abutment rigidity was able to significantly affect the wear pattern of LDS, which seems to be more intense on rigid implant-abutment supports compared to resilient teeth replicas with artificial periodontal ligament. Full article

Dental enamel is a specialized tissue that has adapted over millions of years of evolution to enhance the survival of a variety of species. In humans, enamel evolved to form the exterior protective layer for the crown of the exposed tooth crown. Its unique composition, structure, physical properties and attachment to the underlying dentin tissue allow it to be a resilient, although not self-repairing, tissue. The process of enamel formation, known as amelogenesis, involves epithelial-derived cells called ameloblasts that secrete a unique extracellular matrix that influences the structure of the mineralizing enamel crystallites. There are over 115 known genetic conditions affecting amelogenesis that are associated with enamel phenotypes characterized by either a reduction of enamel amount and or mineralization. Amelogenesis involves many processes that are sensitive to perturbation and can be altered by numerous environmental stressors. Genetics, epigenetics, and environment factors can influence enamel formation and play a role in resistance/risk for developmental defects and the complex disease, dental caries. Understanding why and how enamel is affected and the enamel phenotypes seen clinically support diagnostics, prognosis prediction, and the selection of treatment approaches that are appropriate for the specific tissue defects (e.g., deficient amount, decreased mineral, reduced insulation and hypersensitivity). The current level of knowledge regarding the heritable enamel defects is sufficient to develop a new classification system and consensus nosology that effectively communicate the mode of inheritance, molecular defect/pathway, and the functional aberration and resulting enamel phenotype. Full article

The nonmineralized state of the mammalian periodontal ligament is one of the hallmarks of vertebrate evolution as it provides resilient and nontraumatic tooth anchorage for effective predation. Here we sought to determine how the chromatin state of key mineralization gene promoters contributes to the nonmineralized periodontal ligament in the midst of fully mineralized alveolar bone and cementum anchor tissues. In developing mouse periodontal tissues, RUNX2 was localized to alveolar bone–lining cells, while OSX was localized throughout the periodontal ligament’s soft tissue. Matching RT-PCR amplification data and western blot comparisons demonstrated that the expression of RUNX2 and OSX bone mineralization transcription factors was at least 2.5-fold elevated in alveolar bone osteoblasts versus periodontal ligament fibroblasts. ChIP enrichment data along the RUNX2 and OSX promoters revealed increased H3K4me3 marks in alveolar bone osteoblasts, while H3K9me3 and H3K27me3 marks were elevated in periodontal ligament fibroblasts. In support of an epigenetic mechanism responsible for the inhibition of mineralization gene expression in periodontal progenitors, histone methylation inhibitors DZNep and Chaetocin reactivated RUNX2 and OSX expression in periodontal progenitors and increased alkaline phosphatase and Alizarin Red, while the in vivo application of DZNep in rat maxillae resulted in aberrant mineralization in the periodontal ligament and a narrowing of the nonmineralized periodontal space. Together, these studies demonstrate that the nonmineralized state of the mammalian periodontal ligament is controlled by an epigenetic regulation of the RUNX2 and OSX key mineralization gene promoters. Full article

Complex composite materials are used in many areas of dentistry. Initially, chemically hardened materials were also used, and in this group nanohybrid composites are highly valued. They are often used today, mainly for the direct reconstruction of damaged hard tooth tissue materials for rebuilding damaged tissues using indirect adhesive techniques. The research was conducted to determine the mechanical properties of materials with nanofillers. The article focuses on methods of important test methods for dental prosthetics: resilience, abrasion, wear test, impact strength, hardness, SEM, and chemical analysis. As part of this work, five different series of hybrid composites with nano-fillers were tested. The mechanical properties of composites, such as compressive strength, microhardness, flexural strength, and modulus of elasticity, depend mainly on the type, particle size, and amount of filler introduced. The obtained test results showed that the type and amount of nanofiller have a significant influence on the mechanical and tribological properties. The introduction of nanofillers allowed us to obtain higher mechanical properties compared to classic materials discussed by other researchers. The study observed a change in vibrations in the IR spectrum, which allowed a comparison of the organic structures of the studied preparations. Full article

Charcot-Marie-Tooth (CMT) syndrome is the most common progressive human motor and sensory peripheral neuropathy. CMT type 1E is a demyelinating neuropathy affecting Schwann cells due to peripheral-myelin-protein-22 (PMP22) mutations, modelized by Trembler-J mice. Curcumin, a natural polyphenol compound obtained from turmeric (Curcuma longa), exhibits dose- and time-varying antitumor, antioxidant and neuroprotective properties, however, the neurotherapeutic actions of curcumin remain elusive. Here, we propose curcumin as a possible natural treatment capable of enhancing cellular detoxification mechanisms, resulting in an improvement of the neurodegenerative Trembler-J phenotype. Using a refined method for obtaining enriched Schwann cell cultures, we evaluated the neurotherapeutic action of low dose curcumin treatment on the PMP22 expression, and on the chaperones and autophagy/mammalian target of rapamycin (mTOR) pathways in Trembler-J and wild-type genotypes. In wild-type Schwann cells, the action of curcumin resulted in strong stimulation of the chaperone and macroautophagy pathway, whereas the modulation of ribophagy showed a mild effect. However, despite the promising neuroprotective effects for the treatment of neurological diseases, we demonstrate that the action of curcumin in Trembler-J Schwann cells could be impaired due to the irreversible impact of ethanol used as a common curcumin vehicle necessary for administration. These results contribute to expanding our still limited understanding of PMP22 biology in neurobiology and expose the intrinsic lability of the neurodegenerative Trembler-J genotype. Furthermore, they unravel interesting physiological mechanisms of cellular resilience relevant to the pharmacological treatment of the neurodegenerative Tremble J phenotype with curcumin and ethanol. We conclude that the analysis of the effects of the vehicle itself is an essential and inescapable step to comprehensibly assess the effects and full potential of curcumin treatment for therapeutic purposes. Full article

Background: The early identification of children who have experienced adversity is critical for the timely delivery of interventions to improve coping and reduce negative consequences. Self-report is the usual practice for identifying children with exposure to adversity. However, physiological characteristics that signal the presence of disease or other exposures may provide a more objective identification strategy. This protocol describes a case–control study that assesses whether exposure to adversity is more common in children with tooth enamel anomalies compared to children without such anomalies. Methods: For 150 mother–child pairs from a pediatric dental clinic in Toronto, Canada, maternal interviews will assess the child’s adverse and resilience-building experiences. Per child, one (exfoliated or extracted) tooth will be assessed for suspected enamel anomalies. If anomalies are present, the child is a case, and if absent, the child is a control. Tooth assessment modalities will include usual practice for dental exams (visual assessment) and modalities with greater sensitivity to identify anomalies. Conclusion: If structural changes in children’s teeth are associated with exposure to adversity, routine dental exams could provide an opportunity to screen children for experiences of adversity. Affected children could be referred for follow-up. Full article

Dental caries and periodontal disease represent a health problem and a social cost for the entire population, and in particular for socio-economically disadvantaged individuals who are less resistant to disease. The aim of this review is to estimate the prevalence and severity of the two dental pathologies, caries and periodontal disease, in the different classes of socio-economically disadvantaged subjects and to understand which of them are most affected. A systematic search of the literature was performed in MEDLINE (via PubMed), EMBASE and Web of Science after establishing a suitable search strategy for each database, using keywords related to socio-economically vulnerable classes and health outcomes. Socio-economically disadvantaged individuals are more susceptible to tooth decay and periodontal disease (with relative tooth loss) than non-vulnerable people. Additionally, when multiple vulnerabilities are combined in the same subject, these oral diseases worsen. There is no type of vulnerability more affected by caries and periodontitis than others, since overall they all have severe disease indices. The data from this systematic literature review might be useful for health policy makers looking to allocate more resources and services to socially disadvantaged individuals, resulting in making them more resilient to oral disease due to their social marginalization. Full article