Search Results (33)

Conventional cement concrete pavements often suffer from rapid skid resistance degradation and excessive traffic noise, necessitating effective solutions. This study investigates exposed aggregate concrete (EAC) through orthogonal experimental methods to evaluate the effects of four mix design parameters—water–binder ratio, sand ratio, coarse aggregate volume ratio, and proportion of aggregates >9.5 mm—on surface texture characteristics, skid resistance and noise reduction (SRNR) performance, and mechanical properties. The optimal EAC mix proportions were developed, and the correlations between surface texture characteristics and SRNR performance were established. Results indicate that the proportion of aggregates >9.5 mm significantly influences surface texture characteristics and SRNR performance. The optimal mix proportions (water–binder ratio: 0.43, sand ratio: 31%, coarse aggregate volume ratio: 42%, and proportion of aggregates >9.5 mm: 50%) exhibited superior mechanical properties, achieving a 31.5% increase in pendulum value and a 6.48 dB reduction in tire/surface noise compared to grooved conventional concrete. The noise reduction frequency range is mainly concentrated in the mid-high frequency range of 1.5~4.0 kHz, which is more sensitive to the human ear. High correlations were observed between the surface texture characteristics and SRNR performance. Specifically, noise value decreased progressively with increasing exposed aggregate depth, while the pendulum value exhibited a trend of initial decrease, followed by an increase and subsequent decrease in response to the elevated exposed aggregate area ratio. Compared to traditional cement concrete pavements, the optimized EAC, while maintaining mechanical properties, exhibits superior SRNR performance, providing a valuable reference for the construction of high SRNR cement concrete pavements. Full article

The different sources of noise in a vehicle have long been known, and they include noise from the engine and other mechanical parts, aerodynamic noise, and rolling noise. More specifically, the latter concerns the interaction between the tire and the road surface, and so it is also known as Tire–Road Noise (TRN). One of the parameters influencing TRN is pavement stiffness. The empirical measurement of pavement stiffness, and in particular, its frequency spectrum (dynamic stiffness), is not easy to determine, and only in the last decade have studies emerged about this subject. In these works, two different instrumental chains are employed as follows: the impact hammer one and the dynamic exciter (shaker) one, which has established itself over time as a reference. The objective of this work is to develop a system for the dynamic stiffness measurements of road pavements using the impact hammer capable of producing a similar performance to the shaker while minimizing costs. During the work, a measurement aid device named Test Automation Device (TAD) was designed and implemented to increase the quality of the measurements. In line with the practical execution of the measurement, the analysis and the representation of the results were optimized to obtain results that adhere to the stiffness model proposed in the literature. In the present paper, the TAD, the measurement optimization work, the data analysis performed, and the proposed representation method will be described. Finally, we will present the results obtained and possible future perspectives. Full article

Aiming to reduce noise pollution and optimize the acoustic quality in highway tunnels, the noise characteristics on different types of pavements were analyzed and compared in this research, based on the on-site noise measurement in two tunnels with the free fields as a control group. Specifically, the noise characteristics include two aspects: various noise and noise time attenuation performance. Various noise includes on-board sound intensity (OBSI) noise and cabin noise. The noise time attenuation performance uses the indicator of reverberation time. Three types of pavements were measured, including dense-graded asphalt concrete (DAC) and single-layered and double-layered porous asphalt (PA) pavement. The results showed that, for the same type of pavement, compared with the free fields, the difference in OBSI noise in tunnels was within a range of less than 1 dBA; the cabin noise increased by 3.4 dBA~6.6 dBA. The noise level in tunnels was greater than that outside tunnels, and the longer tunnel exhibited higher traffic noise and worse noise time attenuation performances. For the same tunnel, PA pavement could reduce the cabin noise by 3.8 dBA~6.7 dBA. PA pavement also exhibited shorter reverberation time. The application of PA pavement could effectively improve the acoustic quality in the tunnel. This research contributes to noise pollution abatement and the improvement of the comfort and safety of drivers in tunnels. Full article

This study evaluates the laboratory and field performance of stone mastic asphalt (SMA) mixtures with nominal maximum aggregate sizes (NMAS) of 9.5, 8.0, and 5.6 mm. Aggregates and fine aggregates of these sizes were produced using an impact crusher and a polyurethane screen. Mix designs for SMA overlays on aged concrete pavement were developed. Laboratory tests assessed rutting performance using full-scale accelerated pavement testing (APT) equipment and reflective cracking resistance using an asphalt mixture performance tester (AMPT). Field evaluations included noise reduction using CPX equipment, skid resistance using SN equipment, and bond strength using field cores. Results showed that for 8.0 mm SMA mixtures to achieve the same rutting performance as 9.5 mm SMA, PG76-22 grade binder was required, whereas 5.6 mm SMA required PG82-22. The 8.0 and 5.6 mm SMA mixtures showed 22.2% and 25% reduced crack progression, respectively, compared with the 9.5 mm SMA mixtures. Field evaluations indicated that 8.0 mm and 5.6 mm SMA pavements reduced tire–pavement noise by 1.7 and 0.8 dB, increased skid resistance by 8.5% and 2.0%, and enhanced shear bond strength by 150%, compared with 9.5 mm SMA. Overall, the 8.0 mm SMA mixture on aged concrete pavement demonstrated superior durability and functionality toward sustainable pavement systems. Full article

Conventional asphalt roads are noisy. Currently, there are two main types of mainstream noise-reducing pavements: pore acoustic absorption and damping noise reduction. However, a single noise reduction method has limited noise reduction capability, and porous noise-reducing pavements have a shorter service life. Therefore, this paper aimed to improve the noise-damping performance of porous asphalt mixture by adding rubber granules and extending its service life using electromagnetic induction heating self-healing technology. Porosity and permeability coefficient test, Cantabro test, immersion Marshall stability test, freeze–thaw splitting test, a low-temperature three-point bending experiment, and Hamburg wheel-tracking test were conducted to investigate the pavement performance and water permeability coefficients of the mixtures. A tire drop test and the standing-wave tube method were conducted to explore their noise reduction performance. Induction heating installation was carried out to study the heating rate and healing performance. The results indicated that the road performance of the porous asphalt mixture tends to reduce with an increasing dosage of rubber granules. The road performance is not up to the required standard when the dosage of rubber granules reaches 3%. The mixture’s performance of damping and noise tends to increase with the increase of rubber granule dosage. Asphalt mixtures with different rubber granule dosages have different noise absorption properties, and the mixture with 2% rubber granules has the best overall performance (a vibration attenuation coefficient of 7.752 and an average absorption factor of 0.457). The optimum healing temperature of the porous asphalt mixture containing rubber granules and steel wool fibers is 120 °C and the healing rate is 74.8% at a 2% rubber granule dosage. This paper provides valuable insights for improving the noise reduction performance and service life of porous asphalt pavements while meeting road performance standards. Full article

The automotive industry is currently transforming, primarily due to the rise of electric and hybrid vehicle technologies and the need to reduce vehicle mass and energy losses to decrease consumption, pollution, and raw material usage. Additionally, road surface manufacturers emphasize improving pavement durability and reducing rolling noise. This necessitates precise load condition definitions and drives the need for reliable wheel testing benches. Many current benches use abrasive-coated rollers or synthetic tapes, but devices capable of testing on actual road surfaces are rare. In this work, a novel device for testing tire-pavement interaction is proposed. The system features a cart moving along a closed-track platform, ensuring test repeatability and enabling structural durability tests on uneven surfaces with installed obstacles. The cart is equipped with a cantilever arm capable of supporting either a testing wheel with customizable dimensions and kinematic parameters or a tire integrated with a complete suspension system, moving along a customizable pavement surface. The system includes actuators and sensors for applying vertical loads and adjusting the alignment of the testing wheel (slip angle, camber angle, etc.), allowing the characterization of tire behavior such as wear, fatigue, rolling noise, and rolling resistance. Multibody simulations were performed to evaluate the bench’s feasibility in terms of kinematics, power requirements, and structural loads. Results confirmed how this novel test bench represents a promising advancement in tire testing capabilities, enabling comprehensive studies on tire performance, noise reduction, and the structural dynamics of vehicle subsystems. Full article

Cement concrete pavements are crucial to urban infrastructure, significantly influencing road safety and environmental sustainability with their anti-skid and noise reduction properties. However, while texturing techniques like transverse grooving have been widely adopted to enhance skid resistance, they may inadvertently increase road noise. This study addressed the critical need to optimize pavement textures to balance improved skid resistance with noise reduction. Tests were conducted to assess the influence of surface texture on skid resistance and noise, exploring the relationship between texture attributes and their performance in these areas. The investigation examined the effects of texture representation methods, mean profile depth, and the high-speed sideway force coefficient (SFC) on noise intensity and pavement skid resistance. The findings revealed that transverse grooves significantly improved the SFC, enhancing skid resistance. In contrast, longitudinal burlap drag, through its micro- and macro-texture adjustments, effectively reduced vibration frequencies between the tire and pavement, thus mitigating noise. Utilizing the TOPSIS multi-objective optimization framework, an optimization model for pavement textures was developed to augment skid resistance and noise reduction at varying speeds. The results indicated that at 60 km/h, an optimal balance of groove width, depth, and spacing yielded superior skid resistance with a minimal noise increase. At 80 km/h, increased groove spacing and depth were shown to effectively decrease noise while maintaining efficient water evacuation. The optimal pavement texture design must consider the specific context, including traffic volume, vehicle types, and operating speeds. This study provides essential guidance for optimizing urban cement concrete pavement textures, aiming to diminish traffic noise and bolster road safety. Full article

To assess the medium-term performance of porous asphalt pavement during service and its influence on tire/pavement noise level, a seven-year continuous observation and data analysis study was conducted. Key performance indicators were measured and calculated by using automated pavement technology testing equipment. The noise levels were tested by using the on-board sound intensity (OBSI) method on three types of porous asphalt pavements (PUC-10, PAC-13, and PUC-10 + PAC-13) and one dense thin layer course (DTC) for comparison. The findings indicated that the Damage Rate (DR) and Surface Friction Coefficient (SFC) of porous asphalt pavements diminished greatly over time, while the International Roughness Index (IRI) and Rut Depth (RD) remained relatively stable. The two-layer porous asphalt pavement showed the largest noise reduction over the medium-term. Compared to DTC, the OBSI noise levels of these structures were lower by 2.09 dB, 1.53 dB, and 2.88 dB, respectively. The OBSI was found to be closely correlated with the SFC, IRI, test speed, lane, and pavement type. The RD had a notable effect on the OBSI in PUC-10 pavements. In PUC-10 + PAC-13 pavements, a significant linear relationship was observed between the OBSI and SFC. This is mainly because of the polishing of the coarse aggregates, which leads to micro-texture reduction, high frequency noise increase, and SFC decrease. This study makes a valuable contribution to understanding the laws of porous asphalt pavement performance changes and the relationship between tire/pavement noise and pavement characteristics. Full article

Porous asphalt pavements have a skeletal structure with a large number of interconnecting pores, which can improve drainage, ensure traffic safety, and reduce tire noise. However, it can weaken the mechanical properties of the pavement. One of the key factors affecting the performance of porous asphalt pavements is the quality of compaction, the assessment of which is difficult to accurately quantify. Therefore, Superpave gyratory compaction (SGC) and skeleton penetration tests of porous asphalt mixtures were carried out using three engineering-differentiated gradations in this paper to investigate the gyratory compaction characteristics and the skeleton contact state during penetration. The results show that obvious stages with the increase in number of cycles can be observed during the compaction process. All gradations can achieve the maximum porosity requirements within a reasonable number of compaction cycles, while only the medium and fine gradations can approximately meet the minimum porosity requirements. The coarse gradation takes too long to finish compaction and is almost impossible to meet the minimum porosity. The optimum match between the void ratio of the design gradation and the skeleton contact state can be verified using the VCA ratio and void ratio curves. This is a new method to determine the corresponding target compaction number that can ensure better accuracy and ease of engineering application. Moreover, medium-graded mixtures with better skeletal embedding exhibit greater skeletal strength than coarse-graded aggregates, which provide theoretical support for the establishment of material grade optimization methods. Full article

Impact force induced by tread pattern is one of the major mechanisms of tire noise; thus, how to reduce tire impact noise has been an important issue in regard to tire technology. In this paper, the mechanism of tire–pavement interaction noise is briefly described, and a prediction model for pattern noise is proposed. The prediction model was validated with indoor semi-anechoic chamber and pass-by noise experiments. Then, an optimization method for the tread pattern was proposed by using the basis vector method, and the synthetic pattern shape was generated through a linear combination of basis shape vectors. Finally, a novel multi-objective function was proposed, aimed at minimizing the impact noise generated by the tire pattern, and the weight factors of the basis vectors were optimized with a genetic algorithm. The method proposed in this paper can be used to evaluate or improve pattern performance and reduce trial and error in the pattern design stage. Full article

A modified strain-hardening cementitious composite (SHCC) material, fabricated using corundum aggregates (SHCC-Cor), has been proposed for roadway applications as it offers high structural performance and high skid resistance. However, the acoustic performance of SHCC is unclear and has not been well studied in the past. Theoretically, SHCC may not provide the optimum solution in acoustic performance as it provides a low texture profile, high density, and low porosity. In this study, the acoustic performance of pavement slabs made of SHCC and modified SHCC-Cor are investigated using a nondestructive method to determine the surface roughness (macro texture) of slab surfaces. The pavement–tire noise level was then simulated using SPERoN software. As result, the noise level coming from the pavement made of SHCC could be up to 65 dB(A), while the noise level for SHCC-Cor increased up to 69.2 dB(A) because of the lower shape factor (G) due to a rougher surface as a result of the existence of corundum aggregate on the SHCC surface. The aeroacoustics were also increased compared to the SHCC slab. The modification of SHCC-Cor by introducing grooves (SHCC-Cor-Gro) successfully reduced the sound level coming from the vibration. Full article

The surface condition of roadways has direct consequences on a wide range of processes related to the transportation technology, quality of road facilities, road safety, and traffic noise emissions. Methods developed for detection of road surface condition are crucial for maintenance and rehabilitation plans, also relevant for driving environment detection for autonomous transportation systems and e-mobility solutions. In this paper, the clustering of the tire-road noise emission features is proposed to detect the condition of the wheel tracks regions during naturalistic driving events. This acoustic-based methodology was applied in urban areas under nonstop real-life traffic conditions. Using the proposed method, it was possible to identify at least two groups of surface status on the inspected routes over the wheel-path interaction zone. The detection rate on urban zone reaches 75% for renewed lanes and 72% for distressed lanes. Full article

Tire–pavement interaction noise (TPIN) accounts mainly for traffic noise, a sensitive parameter affecting the eco-based maintenance decision outcome. Consistent methods or metrics for lab and field pavement texture evaluation are lacking. TPIN prediction based on pavement structural and material characteristics is not yet available. This paper used 3D point cloud data scanned from specimens and road pavement to conduct correlation and clustering analysis based on representative 3D texture metrics. We conducted an influence analysis to exclude macroscope pavement detection metrics and macro deformation metrics’ effects (international roughness index, IRI, and mean profile depth, MPD). The cluster analysis results verified the feasibility of texture metrics for evaluating lab and field pavement wear, differentiating the wear states. TPIN prediction accuracy based on texture indicators was high (R² = 0.9958), implying that it is feasible to predict the TPIN level using 3D texture metrics. The effects of pavement texture changes on TPIN can be simulated by laboratory wear. Full article

This paper presents a novel work for classification of road surfaces using deep learning method-based convolutional neural network (CNN) architecture. With the development of advanced driver assistance system (ADAS) and autonomous driving technologies, the need for research on vehicle state recognition has increased. However, research on road surface classification has not yet been conducted. If road surface classification and recognition are possible, the control system can make a more robust decision by validating the information from other sensors. Therefore, road surface classification is essential. To achieve this, tire-pavement interaction noise (TPIN) is adopted as a data source for road surface classification. Accelerometers and vision sensors have been used in conventional approaches. The disadvantage of acceleration signals is that they can only represent the surface profile properties and are masked by the resonance characteristics of the car structure. An image signal can be easily contaminated by factors such as illumination, obstacles, and blurring while driving. However, the TPIN signal reflects the surface profile properties of the road and its texture properties. The TPIN signal is also robust compared to those in which the image signal is affected. The measured TPIN signal is converted into a 2-dimensional image through time–frequency analysis. Converted images were used together with a CNN architecture to examine the feasibility of the road surface classification system. Full article

A large number of waste tires are in urgent need of effective treatment, and breaking waste tires into crumb rubber powder for modifying asphalt has been proved as a good idea to solve waste tires. Crumb rubber modified asphalt not only has good high and low temperature performance, durability, and aging resistance but can also reduce pavement noise and diseases, which has wide application prospects. In this study, crumb rubber powder was desulfurized by mechanochemical method to prepare desulfurized crumb rubber modified asphalt. During the desulfurization process of crumb rubber, the effects of desulfurization process variables including desulfurizer type, desulfurizer content, and desulfurization mixing temperature and time were considered, and then the physical properties of modified asphalt were tested. The test results showed that after mixing crumb rubber powder with desulfurizer, the viscosity of crumb rubber powder modified asphalt can be reduced. Moreover, the storage stability of crumb rubber powder modified asphalt could also be improved by mixing crumb rubber with desulfurizer. Based on the physical properties of crumb rubber powder modified asphalt, the desulfurization process of selected organic disulfide (OD) desulfurizer was optimized as follows: the OD desulfurizer content was 3%, the desulfurization mixing temperature was 160 °C, and the mixing time was 30 min. In addition, Fourier infrared spectroscopy analysis was carried out to explore the modification mechanism of desulfurized crumb rubber powder modified asphalt. There is no fracture and formation of chemical bonds, and the modification of asphalt by crumb rubber powder is mainly physical modification. Full article