Search Results (66)

Reliable detection of microplastics by surface-enhanced Raman scattering (SERS) is often hindered by poor particle–substrate contact and limited access to plasmonic hotspots on conventional planar substrates optimized for molecular adsorption. Here, we report a rapid microwave-assisted carbothermal shock strategy to fabricate silver nanoparticle-decorated electrospun carbon fibers (AgNPs@ECF) as a three-dimensional plasmonic platform tailored for solid microplastic sensing. Localized microwave-induced heating in a mixed ethanol–hexane system enables Ag nanoparticle nucleation and anchoring on conductive carbon fibers within 45 s, yielding a mechanically compliant, junction-rich architecture without chemical reductants or vacuum processing. The AgNPs@ECF composite was evaluated using morphologically weathered polystyrene (PS) and polyethylene terephthalate (PET) microplastics, along with size-controlled PS bead standards ranging from ~50 nm to 45 μm. Across these models, SERS response is governed primarily by particle–substrate contact geometry and near-field accessibility rather than polymer type. The strongest enhancement occurs in the sub-micrometer regime, where particles can engage multiple AgNP-decorated fiber junctions, while ultrasmall and large, smooth particles show reduced enhancement due to limited contact or rapid field decay. Spatially resolved Raman mapping and finite-difference time-domain simulations support a contact-dominated enhancement mechanism, revealing localized field confinement at particle–fiber interfaces. These results establish the design principles for three-dimensional SERS substrates targeting heterogeneous solid particulates, demonstrating that contact-accessible plasmonic architectures are critical for reliable microplastic detection under realistic solid-particle measurement conditions. Full article

Colloidal amorphous structures comprise short-range ordered arrays of monodisperse submicrometer-sized particles. They exhibit angle-independent structural color and hence are expected to be promising candidates for advanced color materials. In particular, non-close-packed colloidal amorphous structures embedded in soft polymers can alter the angle-independent color through stimuli-induced volume changes in the polymer. Consequently, such materials should have significant potential for application in sensor devices. This paper reports the preparation of an elastomer-immobilized non-close-packed colloidal amorphous film with an angle-independent color using a hydrogel-immobilized non-close-packed colloidal amorphous film as the starting material. The swelling solvent (i.e., water) in the hydrogel film was replaced with a hydrophilic elastomer precursor solution, which was photopolymerized to immobilize the colloidal amorphous structure with the separated particles within the elastomer film. The color of the elastomer-immobilized non-close-packed colloidal amorphous film was angle-independent and was easily altered under stretching. Furthermore, hydrophilic carbon black dispersed well in the hydrophilic elastomer precursor solution, improving the saturation of the resultant elastomer-immobilized non-close-packed colloidal amorphous film. The flexible nature of the prepared film should allow it to be attached to curved surfaces, thereby promoting its application as a simple strain sensor to express invisible strains through color changes. Full article

Airborne micro- and nanoplastic particles (MNPs) are increasingly recognized as a potential occupational exposure hazard, yet substance-specific workplace data remain limited. This study quantified airborne MNP concentrations during polyester microfiber production using a correlative SEM–Raman approach that enabled chemical identification and size-resolved particle characterization. The aerosol mixture at the workplace was dominated by sub-micrometer particles, with PET—handled onsite—representing the main process-related MNP type, and black tire rubber (BTR) forming a substantial background contribution. Across both sampling periods, total MNP particle number concentrations ranged between 6.2 × 10⁵ and 1.2 × 10⁶ particles/m³, indicating consistently high particle counts. In contrast, estimated MNP-related mass concentrations were much lower, with PM₁₀ levels of 12–15 µg/m³ and PM_2.5 levels of 1.3–1.6 µg/m³, remaining well below applicable occupational exposure limits and near or below 8 h-equivalent WHO guideline values. Comparison with earlier workplace and indoor studies suggests that previously reported concentrations were likely underestimated due to sampling strategies with low efficiency for small particles. Moreover, real-time optical measurements substantially underestimated particle number and mass in this study, reflecting their limited suitability for aerosols dominated by small or dark particles. Overall, the data show that workplace MNP exposure at the investigated site is driven primarily by very small particles present in high numbers but low mass. The findings underscore the need for substance-specific, size-resolved analytical approaches to adequately assess airborne MNP exposure and to support future development of MNP-relevant occupational health guidelines. Full article

Warm-cloud hygroscopic seeding is widely used in precipitation enhancement, but the conditions under which seeding amplifies or suppresses rainfall remain unclear. Here, we use a two-dimensional slab-symmetric spectral bin microphysics model from Tel Aviv University to simulate a warm convective cloud that occurred over Hainan, China, on 11 May 2024, and design three sets of sensitivity experiments in which hygroscopic particles of different characteristic diameters are introduced under a fixed-mass injection constraint. We find that seeding with submicrometer particles (0.1–0.9 µm) systematically suppresses precipitation, with the strongest reduction for 0.1 µm particles. When super-micrometer particles (1–9 µm) are used, the precipitation response transitions from suppression to enhancement as particle size increases, and this transition occurs at about 2 µm. Seeding with ultra-giant particles (>10 µm) generally enhances rainfall and also advances its onset, with the enhancement strengthening up to ~60 µm before weakening for even larger particles. We further show that the transitional particle size at which the seeding effect changes sign decreases with increasing background aerosol loading, from maritime to polluted urban conditions. These results identify an environment-dependent critical particle size that governs the sign and efficiency of hygroscopic seeding in warm convective clouds. Full article

Mesoporous silica nanoparticles have been synthesized through sol–gel synthesis in basic conditions. Gemini surfactants having urea in the headgroups were used as pore-forming agents. The effect of the spacer length of the surfactant on the particle morphology was studied on the sub-micrometer and nanometer scales using nitrogen porosimetry, small-angle X-ray scattering (SAXS), ultra-small-angle neutron scattering, and scanning and transmission electron microscopy (SEM, TEM). Depending on the spacer, spherical and/or cylindrical nanoparticles formed in different proportions, as revealed by statistical analysis of SEM micrographs. All prepared materials showed the hexagonal pore structure characteristic of the MCM-41 molecular sieves, with the exception of the sample prepared using the gemini surfactant with the shortest spacer length. The influence of the spacer length on the lattice parameter of the pore network, as well as the average size of the ordered domains, has been assessed by SAXS and TEM. Detailed analysis of the TEM images revealed a spread of the lattice parameter in a range of 10–20%. The broadening of the diffraction peaks was shown to be due to the combination of the effects of the finite domain size and the variance of the lattice parameter across the crystalline domains. The structural differences between the silica gels synthesized with the different surfactants were related to the variation of the micelle morphologies, reported in previous light scattering and small-angle scattering experiments. No connection could be revealed between the micelle shape and size and the pore sizes, showing that surfactants with a broad range of spacer lengths can equally well be used for the preparation of MCM-41 materials. Full article

Aerosol uniformity in the mixing chamber is one of the key factors in evaluating performance of aerosol samplers and accuracy of aerosol monitors which could output the direct reading of particle size or concentration. For obtaining high uniformity and a stable test aerosol sample during evaluation, a portable mixing chamber, where the sample and clean air were dual-vortex turbulent mixed, was designed. By using computational fluid dynamics (CFD), particle motion within the mixing chamber was illustrated or explained. By adjusting critical structure parameters of chamber such as height and diameter, the flow field structure was optimized to improve particle mixing characteristics. Accordingly, a novel portable aerosol mixing chamber with length and inner diameter of 0.7 m and 60 mm was developed. Through a combination of simulations and experiments, the operating conditions, including working flow rate, ratio of carrier/dilution clean air, and mixture duration, were studied. Finally, by using the optimized parameters, a mixing chamber with high spatial uniformity where variation is less than 4% was obtained for aerosol particles ranging from 0.3 μm to 10 μm. Based on this chamber, a standardized testing platform was established to verify the sampling efficiency of aerosol samplers with high flow rate (28.3 L·min⁻¹). The obtained results were consistent with the reference values in the sampler’s manual, confirming the reliability of the evaluation system. The testing platform developed in this study can provide test aerosol particles ranging from sub-micrometers to micrometers and has significant engineering applications, such as atmospheric pollution monitoring and occupational health assessment. Full article

The precise preparation and application of nanomicrospheres is currently an emerging research hotspot in the cutting-edge cross-disciplines. As an important functional material, nanosized microspheres show a broad application prospect in biomedicine, chemical engineering, materials science, and other fields. However, microspheres with good monodispersity are still facing technical bottlenecks, such as complicated preparation process and high cost. In this study, a multistage cyclic dielectrophoresis (MC-DEP) technique is innovatively proposed to successfully realize the high-resolution sorting of submicron microspheres. A dielectrophoresis chip adopts a unique electrode design, in which the electrodes are arranged at the top and bottom of the microchannel at the same time. This symmetric electrode structure effectively eliminates the difference in the distribution of dielectrophoretic force in the perpendicular direction and ensures the homogeneity of the initial state of particle sorting. Three pairs of focusing electrodes are in the front section of the microchannel for preaggregation of the microspheres, and the deflection electrodes in the back section are to realize particle size sorting. After this, the upper and lower limits of particle size are limited by multiple cycles of sorting. The multistage cyclic sorting increases the stability of particle deflection under dielectrophoretic forces and reduces the error perturbation caused by the fluid environment. The experimental results show that the multistage cycling sorting scheme significantly improves the monodispersity of the microspheres, and the coefficient of variation of the particle size is significantly reduced from the initial 12.3% to 5.4% after three cycles of sorting, which fully verifies the superior performance of this technology. Full article

The application of wide-bandgap semiconductors in next-generation power modules requires cost-effective Cu particles and a reduced bonding time in the die attachment process to enable efficient industrial-scale manufacturing. Therefore, this study aimed to analyze the effect of Cu particle size variation on pressure-assisted sinter-bondability and bond line shear strength. Cu particles were synthesized through a simple wet-chemical process, in which pH variation was employed to obtain submicrometer-sized Cu particles with average diameters of 500, 300, and 150 nm. The synthesized particles exhibited pure Cu composition, forming only a native oxide layer on their surfaces. In pastes containing these Cu particles, smaller particle sizes led to the delayed evaporation of the reducing solvent, which in turn delayed the exothermic reactions associated with particle sintering and oxidation. However, the sintering-induced exothermic peak became more pronounced as the particle size decreased, confirming that smaller particles improved sinterability. Pressure-assisted sinter bonding performed in air at 300 °C indicated that a decreased particle size contributed to the densification of the bond line structure and an increase in shear strength. Specifically, the paste containing 150 nm Cu particles achieved a highly dense microstructure and an exceptional shear strength of 36.7 MPa within just 30 s of sinter bonding. These findings demonstrate that reducing the particle size is essential for enhancing the sinter-bondability of cost-effective Cu particle-based sinter-bonding pastes. Full article

Solid-state electrolytes for lithium-ion batteries, which enable a significant increase in storage capacity, are at the forefront of alternative energy storage systems due to their attractive properties such as wide electrochemical stability window, relatively superior contact stability against Li metal, inherently dendrite inhibition, and a wide range of temperature functionality. NASICON-type solid electrolytes are an exciting candidate within ceramic electrolytes due to their high ionic conductivity and low moisture sensitivity, making them a prime candidate for pure oxidic and hybrid ceramic-in-polymer composite electrolytes. Here, we report on producing pure and Y-doped Lithium Aluminum Titanium Phosphate (LATP) nanoparticles by spray-flame synthesis. The as-synthesized samples consist of an amorphous component and anatase-TiO₂ crystalline particles. Brief annealing at 750–1000 °C for one hour was sufficient to achieve the desired phase while maintaining the material’s sub-micrometer scale. Rietveld analysis of X-Ray diffraction data demonstrated that the crystal volume increases with Y doping. At the same time, with high Y incorporation, a segregation of the YPO₄ phase was observed in addition to the desired LATP phase. Another impurity phase, LiTiOPO₄, was observed besides YPO₄ and, with higher calcination temperature (1000 °C), the phase fraction for both impurities also increased. The ionic conductivity increased with Y incorporation from 0.1 mS/cm at room temperature in the undoped sample to 0.84 mS/cm in the case of LAY0.1TP, which makes these materials—especially considering the comparatively low sintering temperature—highly interesting for applications in the field of solid-state batteries. Full article

Surface enhanced fluorescence (SEF) based on noble metal nanoparticles is an effective means to achieve high sensitivity in fluorescence detection. Currently, the physical mechanism behind enhanced fluorescence is not fully understood. This paper measures the fluorescence signals of Dihydroporphyrin f methyl ether (CPD4) under both single-photon and two-photon excitation based on submicrometer silver particles with rough morphologies, achieving enhancement factors of 34 and 45 times, respectively. On this basis, by combining the radiative field characteristics produced by the silver particles, a stimulated radiation model of molecules is established to elucidate the changes in the molecular photophysical process when influenced by silver particles. Moreover, the fluorescence lifetime of the molecules was measured, showing that the presence of silver particles induces an increase in the molecular radiative decay rate, causing the fluorescence lifetime to decay from 3.8 ns to 3 ns. The results indicate that the fluorescence enhancement primarily originates from the submicrometer silver particles’ enhancement effect on the excitation light. Additionally, the fluorescence signal emitted by the molecules couples with the silver particles, causing the local surface plasmon resonances generated by the silver particles to also emit light signals of the same frequency. Under the combined effect, the fluorescence of the molecules is significantly enhanced. The findings provide a theoretical foundation for understanding the fluorescence enhancement mechanism of silver particles, adjusting the enhancement effect, and developing enhanced fluorescence detection devices based on submicrometer silver particles, holding significant practical importance. Full article

The processing of pure copper (Cu) has been a challenge for laser-based additive manufacturing for many years since copper powders have a high reflectivity of up to 83% of electromagnetic radiation at a wavelength of 1070 nm. In this study, Cu particles were coated with sub-micrometer tungsten (W) particles to increase the laser beam absorptivity. The coated powders were processed by powder bed fusion-laser beam for metals (PBF-LB/M) with a conventional laser system of <300 watts laser power and a wavelength of 1070 nm. Two different powder manufacturing routes were developed. The first manufacturing route was gas atomization combined with a milling process by a planetary mill. The second manufacturing method was gas atomization with particle co-injection, where a separate W particle jet was sprayed into the atomized Cu jet. As part of the investigations, an extensive characterization of powder and additively manufactured test specimens was carried out. The specimens of Cu/W powders manufactured by the milling process have shown superior results. The laser absorptivity of the Cu/W powder was increased from 22.5% (pure Cu powder) to up to 71.6% for powders with 3 vol% W. In addition, a relative density of test specimens up to 98.2% (optically) and 95.6% (Archimedes) was reached. Furthermore, thermal conductivity was measured by laser flash analysis (LFA) and thermo-optical measurement (TOM). By using eddy current measurement, the electrical conductivity was analyzed. In comparison to the Cu reference, a thermal conductivity of 88.9% and an electrical conductivity of 85.8% were determined. Moreover, the Vickers hardness was measured. The effect of porosity on conductivity properties and hardness was investigated and showed a linear correlation. Finally, a demonstrator was built in which a wall thickness of down to 200 µm was achieved. This demonstrates that the Cu/W composite can be used for heat exchangers, heat sinks, and coils. Full article

The current absence of well-established and standardized methods for characterizing submicrometer- and nano-sized particles in water samples presents a significant analytical challenge. With the increasing utilization of nanomaterials, the potential for unintended exposure escalates. The widespread and persistent pollution of water by micro- and nanoplastics globally is a concern that demands attention, not only to reduce pollution but also to develop methods for analyzing these pollutants. Additionally, the analysis of naturally occurring nano entities such as bubbles and colloidal matter poses challenges due to the lack of systematic and consistent methodologies. This study presents Asymmetric Flow Field-Flow Fractionation (AF4) separation coupled with a UV-VIS spectrometer followed by Multi-Angle Light Scattering (MALS) for detection and size characterization of nanometric entities. It is coupled with an Inductively Coupled Plasma Mass Spectrometer (ICP-MS) for elemental analysis. Water samples from different sources, such as untreated mountain spring water, groundwater, and bottled drinking water, were analyzed. The system was calibrated using pure particle standards of different metallic compositions. Our study demonstrates the capability of AF4-UV-MALS-ICP-MS to detect metals such as Al, Ba, Cu, and Zn in particles of around 200 nm diameter and Mg associated with very small particles between 1.5 and 10 nm in different drinking water samples. Full article

Aqueous complexation has long been considered the only viable means of transporting gold to depositional sites in hydrothermal ore-forming systems. Here, we present direct evidence supporting an alternative hypothesis, namely, the transport of gold as colloidal particles. We observed nano-scale gold particles adsorbed on halloysite and micro-scale gold particles in altered rocks by TEM and SEM in the Shanggong orogenic gold deposit. Based on this evidence, we propose a feasible model for the origin of microscopic gold particles in alteration zones. In the early stage of ore-forming fluid, gold may migrate in the form of collaurum, which is maintained by supercritical CO₂ and colloidal silica. Low salinity and high pressure are conducive to the stable migration of colloidal gold. When the physicochemical conditions change, some collaurum is precipitated and adsorbed by the clay minerals produced by hydrothermal alteration, and some collaurum undergoes growth and evolves into micro-submicrometer-sized gold particles. This study highlighted the significance of collaurum in the formation of orogenic gold deposits. Full article

The relationship between exposure to inhaled inorganic particulate matter and risk for deployment-related lung disease in military personnel is unclear due in part to difficulties characterizing individual exposure to airborne hazards. We evaluated the association between self-reported deployment exposures and particulate matter (PM) contained in lung tissue from previously deployed personnel with lung disease (“deployers”). The PM in deployer tissues was compared to normal lung tissue PM using the analytical results of scanning electron microscopy and inductively coupled plasma mass spectrometry. The majority of PM phases for both the deployers and the controls were sub-micrometer in size and were compositionally classified as aluminum and zirconium oxides, carbonaceous particles, iron oxides, titanium oxides, silica, other silicates, and other metals. The proportion of silica and other silicates was significantly higher in the retained dust from military veterans with biopsy-confirmed deployment-related lung disease compared to the control subjects. Within the deployer population, those who had combat jobs had a higher total PM burden, though the difference was not statistically significant. These findings have important implications for understanding the role of inhaled inorganic dusts in the risk for lung injury in previously deployed military veterans. Full article

Gel-immobilized colloidal amorphous structures comprise short-range-ordered monodisperse submicrometer particles embedded into a soft polymer gel. They exhibit an angle-independent structural color that is tunable in response to external stimuli via a volume change in the gel, which has significant potential for the development of sensors that respond to stimuli via angle-independent color changes. In this study, the amorphous structure of a charged colloidal suspension in water was immobilized in a thermoresponsive poly(N-isopropylacrylamide) (PNIPAM) gel film and simultaneously attached to a polyethylene terephthalate (PET) substrate. The gel film exhibited a uniform angle-independent color that changed in response to changes in temperature (i.e., thermosensitivity). Attachment to the PET substrate suppressed changes in the gel film area and film distortion, despite significant volume changes in the gel. Consequently, the degree of thermosensitivity was enhanced. The PET-attached gel-immobilized colloidal amorphous film was easy to handle and had excellent flexibility, allowing it to wrap around the surfaces of curved objects. These features are advantageous for sensor applications. Full article