Search Results (11)

Fused deposition modeling (FDM) 3D printing (3DP) of PLA biocomposites reinforced with plant-derived cellulosic fibrous materials, including spun yarn, microcrystalline, microfibrillar, nanofibrillar cellulose, and cellulose nanocrystals, offers an environmentally sustainable solution to the mechanical limitations of polymer-only printed materials. Micron- and submicron-scale cellulosic fibers are valued for their renewability, non-toxicity, high surface area, and favorable elastic and specific moduli; notably, micron-scale reinforcements are particularly attractive due to their ease of large-scale industrial production and commercial viability. Similarly, PLA benefits from large-scale production, contributes to CO₂ sequestration through its raw material precursors, and requires less energy for production than non-biodegradable petroleum-derived polymers. Incorporating these raw materials, each of which offers attractive performance properties, complementary commercial strengths, and environmental benefits, as constituent phases in FDM 3D-printed biocomposites (FDMPBs) can further enhance the environmental responsiveness of an already low-waste FDM 3DP technology. Inspired by these compelling advantages, this paper critically reviews research on FDMPB with cellulosic reinforcements in a PLA matrix, uniquely categorizing studies based on the form of cellulosic reinforcement and its impact on the biocomposite’s structure and mechanical performance. Additionally, the review covers biocomposite filament production methods and the equipment involved, presenting an alternative framework for cataloging FDMPB research. A comprehensive literature analysis reveals that the wide variation in feedstocks, fiber–matrix compounding methods, equipment, and processing parameters used in filament production and 3DP complicates the comparison of FDMPB mechanical properties across studies, often resulting in conflicting outcomes. Key processing parameters have been compiled to bridge this gap and offer a more nuanced understanding of the cause-and-effect relationships governing biocomposite properties. Finally, targeted recommendations for future research on developing FDMPB with a PLA matrix and micron-scale cellulosic reinforcements are provided, addressing the knowledge gaps and challenges highlighted in the peer-reviewed literature. Full article

Optical coherence tomography (OCT) phantoms are essential tools for calibrating imaging systems, validating diagnostic algorithms, and bridging technological advancements with clinical applications. This review explores the development and application of materials used in OCT phantoms, emphasising their optical, mechanical, and biochemical fidelity to biological tissues. Gelatin-based phantoms (n = 1.35) offer controllable absorbance and scattering, with penetration depths (PDs) of 500–2000 µm and scattering coefficients (SCs) of 5–20 cm⁻¹ but are unstable at room temperature. Silicone phantoms (n = 1.41) are durable and stable, with SCs of 10–15 cm⁻¹, suitable for long-term studies. Polydimethylsiloxane (PDMS) phantoms (n = 1.41) provide manageable optical properties and are used in microfluidic applications. Polyvinyl alcohol (PVA) phantoms (n = 1.48) mimic soft tissue mechanics, with SCs of 5–15 cm⁻¹, but require freeze–thaw cycles. Fibrin phantoms (n = 1.38) simulate blood clotting, with SCs of 5–20 cm⁻¹. Scattering particles like polystyrene (n = 1.57) and titanium dioxide (TiO₂, n = 2.49) offer modifiable properties, while silica microspheres (SiO₂, n = 3.6) and gold nanoshells (n = 2.59) provide customisable optical characteristics. These materials and particles are crucial for simulating biological tissues, enhancing OCT imaging, and developing diagnostic applications. Despite progress, challenges persist in achieving submicron resolution, long-term stability, and cost-effective scalability. Full article

In this study, we investigate the potential of two-photon lithography (2PL) as a solution to the challenges encountered in conventional membrane fabrication techniques, aiming to fabricate tailor-made membranes with high-resolution submicron pore structures suitable for advanced applications. This approach led to the development of fabrication techniques and printed membranes that can be adapted to various lab-on-a-chip (LOC) devices. Membranes were fabricated with pore diameters as small as 0.57 µm and porosities of 4.5%, as well as with larger pores of approximately 3.73 µm in diameter and very high porosities that reached up to 60%. Direct 3D printing of membranes offers a pathway for fabricating structures tailored to specific applications in microfluidics, enabling more efficient separation processes at miniature scales. This research represents a significant step towards bridging the gap between membrane technology and microfluidics, promising enhanced capabilities for a wide array of applications in biotechnology, chemical analysis, and beyond. Full article

This study employed novel joint treatments to strengthen the carbon fiber reinforced polymer (CFRP) composites. Vertically aligned carbon nanotubes (VACNTs) were prepared in situ on the catalyst-treated CF surface via the chemical vapor deposition (CVD) method, intertwining into three-dimensional fiber-nets and fully surrounding CF to form an integrated structure. The resin pre-coating (RPC) technique was further used to guide diluted epoxy resin (without hardener) to flow into nanoscale and submicron spaces to eliminate void defects at the root of VACNTs. Three-point bending testing results showed the “growing CNTs and RPC”-treated CFRP composites yielded the best flexural strength, a 27.1% improvement over the specimens without treatment, while the failure modes indicated that the original delamination failure was changed into “flexural failure” with through-the-thickness crack propagation. In brief, growing VACNTs and RPC on the CF surface enabled toughening of the epoxy adhesive layer, reducing potential void defects and constructing the integrated quasi-Z-directional fiber bridging at the CF/epoxy interface for stronger CFRP composites. Therefore, the joint treatments of growing VACNTs in situ via the CVD method and RPC technique are very effective and have great potential in manufacturing high-strength CFRP composites for aerospace applications. Full article

Exosomes and other extracellular vesicles (EVs) play a significant yet poorly understood role in cell–cell communication during homeostasis and various pathological conditions. Conventional in vitro and in vivo approaches for studying exosome/EV function depend on time-consuming and expensive vesicle purification methods to obtain sufficient vesicle populations. Moreover, the existence of various EV subtypes with distinct functional characteristics and submicron size makes their analysis challenging. To help address these challenges, we present here a unique chip-based approach for real-time monitoring of cellular EV exchange between physically separated cell populations. The extracellular matrix (ECM)-mimicking Matrigel is used to physically separate cell populations confined within microchannels, and mimics tissue environments to enable direct study of exosome/EV function. The submicron effective pore size of the Matrigel allows for the selective diffusion of only exosomes and other smaller EVs, in addition to soluble factors, between co-cultured cell populations. Furthermore, the use of PEGDA hydrogel with a very small pore size of 1.2 nm in lieu of Matrigel allows us to block EV migration and, therefore, differentiate EV effects from effects that may be mediated by soluble factors. This versatile platform bridges purely in vitro and in vivo assays by enabling studies of EV-mediated cellular crosstalk under physiologically relevant conditions, enabling future exosome/EV investigations across multiple disciplines through real-time monitoring of vesicle exchange. Full article

In this study, Cu matrix composites reinforced with reduced graphene oxide-coated submicron spherical Cu (SSCu@rGO) exhibiting both high-strength plastic product (UT) and high electrical conductivity (EC) were prepared. SSCu@rGO results in the formation of Cu₄O₃ and Cu₂O nanotransition layers to optimize the interface combination. In addition, as a flow carrier, SSCu@rGO can also render graphene uniformly dispersed. The results show that SSCu@rGO has a significant strengthening effect on the Cu matrix composites. The relative density (RD) of the SSCu@rGO/Cu composites exceeds 95%, and the hardness, UT, and yield strength (YS) reach 106.8 HV, 14,455 MPa% (tensile strength (TS) 245 MPa, elongation (EL) 59%), and 119 MPa; which are 21%, 72%, and 98% higher than those of Cu, respectively. Furthermore, EC is 95% IACS (International Annealed Copper Standard), which is also higher than that of Cu. The strength mechanisms include transfer load strengthening, dislocation strengthening, and grain refinement strengthening. The plastic mechanisms include the coordinated deformation of the interface of the Cu₄O₃ and Cu₂O nanotransition layers and the increase in the fracture energy caused by graphene during the deformation process. The optimized EC is due to SSCu@rGO constructing bridges between the large-size Cu grains, and graphene on the surface provides a fast path for electron motion. This path compensates for the negative influence of grain refinement and the sintering defects on EC. The reduced graphene oxide-reinforced Cu-matrix composites were studied, and it was found that the comprehensive performance of the SSCu@rGO/Cu composites is superior to that of the rGO/Cu composites in all aspects. Full article

This paper reports the influence of submicron hydrophilic fibers on the hydration and microstructure of Portland cement paste. Submicron fibrillated cellulose (SMC) fibers was prepared by the acid hydrolysis of cotton fibers in H₂SO₄ solution (55% v/v) for 1.5 h at a temperature of 50 °C. The SMC fibers were added into cement with a dosage of 0.03 wt.%, and the effect of SMC on the hydration and microstructure of cement paste was investigated by calorimeter analysis, XRD, FT-IR, DSC-TG, and SEM. Microcrystalline cellulose (MCC) fibers were used as the contrast admixture with the same dosage in this study. The results show that the addition of SMC fibers can accelerate the cement hydration rate during the first 20 h of the hydration process and improve the hydration process of cement paste in later stages. These results are because the scale of SMC fibers more closely matches the size of the C-S-H gel compared to MCC fibers, given that the primary role of the SMC is to provide potential heterogeneous nucleation sites for the hydration products, which is conducive to an accelerated and continuous hydration reaction. Furthermore, the induction and bridging effects of the SMC fibers make the cement paste microstructure more homogeneous and compact. Full article

The research arose as a result of the need to use the femtosecond laser to fabricate sub-micron and nano-sized bridges that could be analyzed for the Josephson effect. The femtosecond laser has a low pulse duration of 130 femtoseconds. Hence in an optical setup it was assumed that it could prevent the thermal degradation of the superconductive material during fabrication. In this paper a series of micron and sub-micron sized bridges where fabricated on superconductive yttrium barium copper oxide (YBCO) thin film using the femtosecond laser, a spherical convex lens of focal length 30 mm and the G-code control programming language applied to a translation stage. The dimensions of the bridges fabricated where analyzed using the atomic force microscope (AFM). As a result, micron sized superconductive bridges of width 1.68 $\mathsf{\mu }\mathrm{m}$, 1.39 $\mathsf{\mu }\mathrm{m}$, 1.23 $\mathsf{\mu }\mathrm{m}$ and sub-micron sized bridges of width 858 nm, 732 nm where fabricated. The length of this bridges ranged from 9.6 $\mathsf{\mu }\mathrm{m}$ to 12.8 $\mathsf{\mu }\mathrm{m}$. The femtosecond laser technique and the spherical convex lens can be used to fabricate bridges in the sub-micron dimension. Full article

The processes removing aerosols from the atmosphere during rainfall are generically referred to as scavenging. Scavenging influences aerosol distributions in the atmosphere, with consequent effects on cloud properties, radiative forcing, and human health. In this study, we investigated the below-cloud scavenging process, specifically focusing on the scavenging of 0.2 to 2 µm-sized microbial aerosols by populations of water drops with average diameters of 3.0 and 3.6 mm. Rainfall was simulated in convective boundary layer air masses by dispensing the water drops from a 55 m bridge and collecting them at ground level. Particles and microbial cells scavenged by the water drops were visualized, enumerated, and sized using scanning electron and epifluorescence microscopy. Aerosolized particles and DNA-containing microbial cells of 2 µm diameter were scavenged at efficiencies similar to those reported previously in empirical studies; however, the efficiencies derived for smaller aerosols were significantly higher (one to three orders of magnitude) than those predicted by microphysical modeling. Application of the derived scavenging efficiencies to cell data from rainfall implies that, on average, approximately 50 to 70% of the 1 µm microbial cells in the precipitation originated from within the cloud. Further study of submicron to micron-sized aerosol scavenging over a broader raindrop size distribution would improve fundamental understanding of the scavenging process and the capacity to estimate (bio)aerosol abundances in the source cloud through analysis of rainfall. Full article

Zirconium is an element of considerable petrogenetic significance but is rarely found in hematite at concentrations higher than a few parts-per-million (ppm). Coarse-grained hematite ore from the metamorphosed Peculiar Knob iron deposit, South Australia, contains anomalous concentrations of Zr and has been investigated using microanalytical techniques that can bridge the micron- to nanoscales to understand the distribution of Zr in the ore. Hematite displays textures attributable to annealing under conditions of high-grade metamorphism, deformation twins (r~85° to hematite elongation), relict magnetite and fields of sub-micron-wide inclusions of baddeleyite as conjugate needles with orientation at ~110°/70°. Skeletal and granoblastic zircon, containing only a few ppm U, are both present interstitial to hematite. Using laser-ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) spot analysis and mapping, the concentration of Zr in hematite is determined to be ~260 ppm on average (up to 680 ppm). The Zr content is, however, directly attributable to nm-scale inclusions of baddeleyite pervasively distributed throughout the hematite rather than Zr in solid solution. Distinction between nm-scale inclusions and lattice-bound trace element substitutions cannot be made from LA-ICP-MS data alone and requires nanoscale characterization. Scandium-rich (up to 0.18 wt. % Sc₂O₃) cores in zircon are documented by microprobe analysis and mapping. Using high-angle annular dark field scanning transmission electron microscopy imaging (HAADF-STEM) and energy-dispersive spectrometry STEM mapping of foils prepared in-situ by focused ion beam methods, we identify [ $0\overline{1}1$ ]_baddeleyite epitaxially intergrown with [ $2\overline{2}.1$ ]_hematite. Lattice vectors at 84–86° underpinning the epitaxial intergrowth orientation correspond to directions of r-twins but not to the orientation of the needles, which display a ~15° misfit. This is attributable to directions of trellis exsolutions in a precursor titanomagnetite. U–Pb dating of zircon gives a ²⁰⁶Pb/²³⁸U weighted mean age of 1741 ± 49 Ma (sensitive high-resolution ion microprobe U–Pb method). Based on the findings presented here, detrital titanomagnetite from erosion of mafic rocks is considered the most likely source for Zr, Ti, Cr and Sc. Whether such detrital horizons accumulated in a basin with chemical precipitation of Fe-minerals (banded iron formation) is debatable, but such Fe-rich sediments clearly included detrital horizons. Martitization during the diagenesis-supergene enrichment cycle was followed by high-grade metamorphism during the ~1.73–1.69 Ga Kimban Orogeny during which martite recrystallized as granoblastic hematite. Later interaction with hydrothermal fluids associated with ~1.6 Ga Hiltaba-granitoids led to W, Sn and Sb enrichment in the hematite. By reconstructing the evolution of the massive orebody at Peculiar Knob, we show how application of complimentary advanced microanalytical techniques, in-situ and on the same material but at different scales, provides critical constraints on ore-forming processes. Full article

Mechanisms of protecting soil carbon (C) are still poorly understood despite growing needs to predict and manage the changes in soil C or organic matter (OM) under anticipated climate change. A fundamental question is how the submicron-scale interaction between OM and soil minerals, especially poorly-crystalline phases, affects soil physical aggregation and C stabilization. Nano-sized composites rich in OM and poorly-crystalline mineral phases were presumed to account for high aggregate stability in the Andisol we previously studied. Here we searched for these nanocomposites within a sonication-resistant aggregate using scanning transmission X-ray microscopy (STXM) and near-edge X-ray absorption fine structure (NEXAFS) as well as electron microscopy (SEM, TEM). Specifically, we hypothesized that nanometer-scale spatial distribution of OM is controlled by poorly-crystalline minerals as both co-exist as physically-stable nanocomposites. After maximum dispersion of the cultivated Andisol A-horizon sample in water, one aggregate (a few µm in diameter) was isolated from 0.2–2 µm size fraction which accounted for 44–47% of total C and N and 50% of poorly-crystalline minerals in bulk soil. This fraction as well as <0.2 µm fraction had much higher extractable Al and Fe contents and showed greater increase in specific surface area (N₂-BET) upon OM oxidation compared to bulk and >2 µm size fractions, implying high abundance of the nanocomposites in the smaller fractions. The isolated aggregate showed a mosaic of two distinctive regions. Smooth surface regions showed low adsorption intensity of carbon K-edge photon energy (284–290 eV) with well-crystalline mineralogy, whereas rough surface regions had features indicative of the nanocomposites: aggregated nanostructure, high C intensity, X-ray amorphous mineral phase, and the dominance of Si, O, Al, and Fe based on SEM/EDX and TEM/EDX. Carbon functional group chemistry assessed by NEXAFS showed the dominance of amide and carboxyl C over aromatic and aliphatic C with some variation among the four rough surface regions. Together with C and N isotopic patterns among the size fractions (relatively low C:N ratio, high ¹⁵N natural abundance, and more positive Δ¹⁴C of the <2 μm fractions), our results provided the direct evidence of preferential binding of microbially-altered, potentially-labile C with poorly-crystalline mineral phases at submicron scale. The role of the nanocomposite inferred from this study may help to bridge the knowledge gap between physical aggregation process and biogeochemical reactions taking place within the soil physical structure. Full article