Search Results (325)

To address the current absence of targeted gradation design for porous asphalt pavements both domestically and internationally, this study employs the Coarse Aggregate Void Filling (CAVF) method to design the gradation of porous asphalt mixtures. Marshall stability tests, rutting tests, and scattering tests were conducted to investigate the relationship between coarse aggregate proportions and the structural stability of the mixture skeleton. An orthogonal experimental design was further utilized to examine the influence of three levels of fine aggregate gradation on the acoustic absorption characteristics of the mixture, and to analyze the effects of aggregate gradation on the primary pore diameter, connected pore diameter, and connected pore length. The results indicate that the coarse aggregate gradation predominantly governs the skeleton strength and overall pavement performance of the mixture, whereas the fine aggregate gradation exhibits significant effects on the interconnected void ratio, pore structure, and sound absorption performance. The optimal roughness range of coarse aggregates in porous asphalt mixtures is determined to be 0.46–0.52. The proportion of 0.6–1.18 mm aggregates has a pronounced influence on the primary pore diameter, connected pore diameter, and connected pore length. By integrating the design considerations for both coarse and fine aggregate gradations, a recommended gradation range for porous asphalt mixtures is proposed that achieves a balance between pavement performance and sound absorption/noise-reduction effectiveness. Full article

Underwater acoustic coatings are widely used to suppress low-frequency noise radiation and sonar reflection in underwater vehicles. In this study, an underwater acoustic coating model consisting of viscoelastic rubber layers and micro-perforated panel (MPP) structures is investigated, with particular emphasis on the low-frequency sound absorption mechanism and predictive modeling. Based on an improved transfer function method, a novel Micro-Perforated Panel Acoustic Coating Layer (MPPACL) model is developed to describe the coupled acoustic behavior of multilayer coatings under underwater conditions. The low-frequency sound absorption performance is primarily governed by the viscoelastic characteristics of the rubber layer, including material damping and complex modulus, while the incorporation of the MPP further enhances absorption through resonance effects. To efficiently explore the relationship between structural parameters and acoustic response, an ensemble learning-based deep neural network (ELDNN) is constructed using analytically generated data, enabling both forward prediction of sound absorption performance and inverse prediction of structural design parameters. The results show that the frequency prediction accuracy of the IDNN model is 3.7 times that of the DNN model. Furthermore, the proposed MPPACL model has achieved a significantly enhanced sound absorption effect within the frequency range of 50 to 2000 hertz. This effect has also been further verified through underwater experiments. The proposed framework provides an efficient and reliable approach for the design and optimization of underwater acoustic coatings. Full article

This study proposes a novel coplanar spiral-varying-channel space-coiled acoustic metamaterial (CSV-SCAM) for efficient low-frequency noise control in the range of approximately 200–400 Hz. By integrating continuously graded spiral channels with secondary spiral branches, the proposed structure enables multi-stage acoustic impedance matching and enhanced thermo-viscous dissipation, effectively overcoming the bulkiness and limited low-frequency efficiency of conventional porous absorbers. Finite element simulations and impedance tube experiments demonstrate that the CSV-SCAM achieves near-unity deep-subwavelength sound absorption, with a peak sound absorption coefficient exceeding 0.99 around 750–850 Hz using a thickness of only 10 mm. Furthermore, hybrid configurations composed of units with different branch numbers significantly broaden the effective absorption bandwidth by more than 20% while maintaining high absorption levels. Compared with traditional Helmholtz resonators, the proposed metamaterial exhibits superior compactness, structural robustness, and design flexibility, providing a promising solution for practical low-frequency noise mitigation in space-constrained engineering applications. Full article

Plastic pollution represents a significant challenge for the building industry, where synthetic foils are extensively used as acoustic absorbers or vapour barriers but persist in the environment for decades, causing risks to ecosystems and human health. In addition, conventional construction materials such as concrete and glass often provide poor acoustic performance, leading to a growing reliance on synthetic acoustic absorbers. In this study, we propose alginate—a biopolymer derived from brown seaweed—as an alternative sustainable material for indoor acoustic conditioning. Thin, bendable, and transparent alginate foils were fabricated and characterized in the impedance tube to assess their sound absorption properties. Results reveal that alginate foils achieve acoustic absorption coefficients comparable to conventional synthetic-based absorbers, while offering biodegradability and a renewable origin. Their physical properties further support potential integration into indoor architectural design, where flexible and transparent properties are desirable. Overall, the findings highlight alginate’s potential as an environmentally friendly replacement for synthetic acoustic foils, supporting the goals of acoustic sustainability and the associated long-term impacts of plastic pollution in the built environment. Full article

Airframe noise generated at wing trailing edges and high-lift devices, such as flaps, remains a major challenge during landing, with significant contributions in the low-frequency band of 500–1500 Hz. While solid surfaces reflect this acoustic energy, metallic porous materials can effectively absorb it through viscous and thermal dissipation within their internal pore structure. To address this, the present study examines the acoustic absorption characteristics of open-cell AlSi porous cylinders featuring controlled pore diameters between 0.3 mm and 2.25 mm. Measurements were conducted in an acoustic impedance tube according to the ISO 10534-2:2023 standard, using six cylindrical samples (28 mm diameter, 70 mm length). Two sets of measurements were performed for each sample (front and rear faces), and the average values were used. The findings indicate that the normal-incidence sound absorption coefficient α rises as pore size increases, reaching 0.93–0.97 at low frequencies of 500–700 Hz for the samples with the largest pores (1.8–2.25 mm). These results indicate that open-cell AlSi alloys offer strong low-frequencies sound absorption, positioning them as promising options for aeroacoustic noise mitigation, including applications such as porous trailing edge and hybrid flap designs. Full article

The upper atmospheric microwave sounding channels data are important for atmospheric data assimilation and retrieval. However, radiative transfer simulation accuracy is constrained by the precise characterization of the Zeeman splitting effect. This study investigates key influencing factors in upper-atmospheric microwave radiance simulations, focusing on the geomagnetic field parameters and the Zeeman splitting absorption coefficients. A three-dimensional (3D) atmosphere-magnetic coupling dataset is constructed using the Sounding of the Atmosphere using Broadband Emission Radiometry (SABER) version 2.0 Level 2A atmospheric profiles and the International Geomagnetic Reference Field (IGRF-13) as input for the microwave Line-by-Line (LBL) model. Observations from Special Sensor Microwave Imager/Sounder (SSMIS) channels 19 and 20 are used to quantitatively compare the effects of 2D and 3D geomagnetic fields on simulations and evaluate the impact of updated Zeeman splitting coefficients. Quantitative analysis reveals that the average vertical attenuation rate of geomagnetic field strength between 50 and 0.001 hPa is 2.98%, and using 3D magnetic field parameters improves the observation and simulation bias (O-B) for SSMIS channels 19 and 20 by approximately 3.67% and 3.52%, respectively. The updated microwave LBL model, incorporating molecular self-spin interactions and higher-order Zeeman effects, reduces the mean absolute error (MAE) and root mean square error (RMSE) of the SSMIS channel 20 by approximately 2.7% and 2.25%, respectively. Experimental results indicate that the 7⁺ line within a 2 MHz frequency shift is sensitive to moderate magnetic field strength (0.35–0.55 Gauss), while the 1⁻ line is sensitive to strong magnetic fields (0.5–0.7 Gauss). This study demonstrates that optimizing geomagnetic field representation and Zeeman splitting coefficients can improve upper atmospheric microwave radiance simulation accuracy by detailed comparison with observations. Full article

This study investigates the synergistic use of Fischer–Tropsch wax (FTW) and recycled rubber powder (RP) as dual modifiers in stone mastic asphalt (SMA11) to improve its mechanical and functional performance. Rheological analysis demonstrated that an FTW content of 4% achieves the optimal balance of high-temperature rutting resistance, aging resistance, and workability, with a binder viscosity of 1.6 Pa·s at 135 °C. When incorporated into SMA11 mixtures at 15%, RP yielded the best overall mechanical performance, including a reduction in rut depth to 1.22 mm and a 25% decrease in wheel tracking slope (WTS). The 15% RP mixtures also exhibited superior long-term skid resistance (μ_m = 0.329 after 180,000 polishing cycles, corresponding to a 13% reduction in braking distance) and enhanced thermal cracking resistance (failure temperature improved by 8.0 °C to −32.7 °C). An RP content of 5% maximized moisture resistance (ITSR = 100%), while 10% RP produced the highest mid-frequency sound absorption coefficient (α = 0.050). The hybrid modification system enables a 20 °C reduction in production temperature, consistent with published data on wax-based warm-mix technologies, and is associated with reduced energy consumption and lower emissions. The approach simultaneously supports sustainable pavement design through the high-value reuse of waste tire rubber. Full article

In this study Laminated Veneer Lumber (LVL)—widely used in structural wood applications—was manufactured from seven poplar veneers bonded with polyurethane (PU) adhesive and reinforced with either one sheet of glass fiber or carbon fiber fabrics. In order to determine the effects of the fiber fabrics incorporated into the structure of the produced LVLs on their thermal and acoustic insulation performance in structural applications, the thermal conductivity coefficient (λ), thermal transmittance (U), sound absorption coefficient (α), and sound transmission loss (dB) values were determined. The experimental results indicated that the thermal conductivity coefficient of the glass fiber-reinforced LVL was lower than that of both the control group and the carbon fiber-reinforced LVL. The thermal transmittance coefficient, an important indicator of thermal insulation performance in buildings, followed a similar trend. Regarding the sound absorption coefficients, the fiber fabric-reinforced LVL samples demonstrated lower coefficients compared to the control group. For sound transmission loss, no significant differences were observed among the groups, and the sound transmission loss was found to increase with frequency. Results indicate that glass fiber-reinforced LVL composites can be used as replacement of other wood-based insulating materials in green buildings which exhibit worse sound insulation or thermal insulation and which are significantly more affected by changes in relative humidity of surrounding air. Full article

This paper focuses on examining the impact of introducing sound scattering in room acoustic modelling, using a ray tracing approach. A parametric study is conducted on a simplified shoebox auditorium, isolating distinct factors, such as the average absorption of the room, room geometry, volume of the space or the introduction of prismatic-shape diffusers. Diffusion is considered by assigning a scattering coefficient (s) to the surfaces, except in the analysis of a prismatic diffuser, which is modelled using a geometric approach. Changes in the reverberation time are analyzed alongside their corresponding just noticeable differences (JNDs). It was found that sound scattering can reduce reverberation time, especially in rooms with parallel walls, but only when sufficient and well-distributed sound absorption is present. Geometric modifications that remove parallelism reduce flutter echoes and can decrease reliance on scattering. Volume scaling of a room has negligible perceptual influence on sound scattering, whereas modifying room proportions offers a stronger influence on reverberation perception. Prismatic diffusers provide efficient geometric diffusion, achieving outcomes comparable to flat surfaces assigned with medium sound scattering coefficients. Full article

The development of high-performance, sustainable biocomposites requires biodegradable matrices and optimized natural reinforcements. In this study, flax fiber-reinforced polylactic acid (PLA) hybrid biocomposites incorporating waste pistachio nut shells (WPNS), waste tea leaf fiber (WTLF), and waste quail eggshell (WQES) were developed and evaluated, with direct comparison to previously reported jute-based hybrid systems to assess the benefits of fiber substitution. The composites were fabricated via compression molding and characterized for their mechanical, thermal, acoustic, surface, and moisture-related properties. Replacing the jute with flax resulted in a consistent performance enhancement. Among the hybrids, the flax–WPNS composite exhibited the highest tensile and flexural performance, achieving tensile strength improvements of approximately 30–40% over neat PLA due to effective stress transfer and crack deflection. The flax–WTLF composite showed superior acoustic behavior, attaining a maximum sound absorption coefficient of approximately 0.65–0.70 at mid-to-high frequencies, attributed to its porous microstructure. In contrast, the flax–WQES composite demonstrated the highest thermal conductivity (0.54 W/(mK)) and apparent density (2.24 g/cm³), reflecting dense packing and the presence of CaCO₃-rich particles. Scanning electron microscopy revealed distinct microstructural mechanisms governing these property-specific responses, including differences in interfacial bonding, void distribution, and filler packing efficiency. An integrated fuzzy CRITIC–COPRAS multicriteria decision-making approach identified the flax–WPNS hybrid as the optimal overall formulation. The results clearly demonstrate that flax fibers outperform jute as a reinforcement in PLA-based hybrid biocomposites, and that targeted combinations of flax and waste-derived fillers enable multifunctional performance optimization for sustainable engineering applications. Full article

Amid increasing demand for energy efficiency and reduced CO₂ emissions in the building sector, natural fibres such as sheep wool are gaining attention as a sustainable raw material for low-impact insulation materials. This review summarises the current state of research on the thermal and acoustic properties of sheep wool-based composites and their applications in low-carbon construction. The fibre structure, thermal conductivity, hygroscopicity, heat storage capacity, and sound absorption coefficient are discussed, highlighting the competitiveness of sheep wool compared to conventional synthetic and mineral materials. The review also addresses the use of wool fibres in cement composites, insulation panels, sound-absorbing materials, and sorption mats, emphasising their potential in humidity regulation, acoustic comfort, and circular economy strategies. A literature analysis indicates that utilising sheep wool waste can reduce environmental impact, lower the carbon footprint of building materials, and enhance local agricultural value. The review provides an overview of current knowledge on sustainable sheep wool-based insulation materials and focuses on an interdisciplinary and quantitative approach to the thermal, acoustic, and environmental performance of composites based on waste sheep wool, combined with an analysis of their applicability in low-carbon construction and circular economy frameworks. Future research should focus on assessing long-term durability, material ageing under real service conditions, and standardised life cycle assessment (LCA) methodologies to enable reliable comparison with conventional insulation materials. Full article

Unlike classical multi-layered micro-perforated panels (MPPs), which rely on sub-millimeter orifices for sound dissipation, we propose a multi-layered porous Helmholtz resonators absorber. It consists of alternately layered perforated porous material panels and perforated rigid panels with millimeter- to centimeter-scale orifices, primarily relying on porous materials for sound energy dissipation. Theoretically, perforated porous material panels are modeled as homogeneous fluid layers using double porosity theory, and the total surface impedance is derived through bottom-to-top impedance translation. A double-layered prototype was tested to validate the theoretical and numerical models, achieving near-perfect absorption peaks at 262 Hz and 774 Hz, with a subwavelength total thickness of 11 cm and a broadband absorption above an absorption coefficient of 0.7 from 202 Hz to 1076 Hz. Simulations of sound pressure, particle velocity, power dissipation, and sound intensity flow confirm that Helmholtz resonances in each layer enhance sound entry into resistive porous materials, causing absorption peaks. Parameter studies show this absorber maintains high absorption peaks across wide ranges of orifice diameters and panel thicknesses. Finally, an optimized triple-layer porous Helmholtz resonators absorber achieves an ultra-broadband absorption above a coefficient of 0.95 from 280 Hz to 1349 Hz with only 16.5 mm thickness. Compared with conventional MPPs, this design features significantly larger orifices that are easier to fabricate and less susceptible to blockage in harsh environments, offering an alternative solution for low-frequency and broadband sound absorption. Full article

Low-frequency noise, primarily generated by transformers and electrical machinery in substations, presents considerable environmental and health risks due to its strong penetration and minimal attenuation. Conventional noise control methods often fail to effectively absorb such low-frequency sounds. In response to this challenge, acoustic metamaterials featuring unique subwavelength structures have emerged as a promising solution for absorbing low-frequency and broadband noise. This study introduces a novel sound-absorbing metamaterial that integrates parallel-connected Helmholtz resonators with a helical cavity structure. To enhance its performance across a broad frequency range, the metamaterial is optimized using a genetic algorithm. Experimental validation, based on 3D-printed samples and impedance tube measurements, demonstrates high absorption efficiency at target frequencies (100 Hz, 300 Hz, and 500–1300 Hz), with absorption coefficients exceeding 0.9. The results confirm that the metamaterial effectively reduces low-frequency core noise. This work represents a significant advancement in noise control technologies for substations, with broader implications for urban noise mitigation and environmental protection. Full article

The increasing amount of multilayer packaging waste poses significant environmental challenges and calls for sustainable valorization solutions. This study aimed to investigate the acoustic properties of composite materials produced by hot-pressing multilayer waste without the addition of binders or other substances. The waste was carefully cleaned and shredded into square or strip-like geometries, and the composite material plates were compressed at different temperatures (120 °C, 125 °C, 130 °C, 135 °C, and 140 °C) under a constant pressure of 5 MPa. The sound absorption coefficients were evaluated for representative samples, with results analyzed as a function of constituent geometry and processing temperature. Experimental results indicate that the pressing temperature critically affects the internal structure of the material, while waste shape exhibits a frequency-dependent influence on the absorption coefficient. The resulting composite materials display low porosity, which limits internal sound absorption and promotes sound wave reflection, indicating that these materials are more suitable for sound insulation rather than acoustic absorption. These results highlight the potential of multilayer packaging waste-based composites as a sustainable solution for noise control applications and highlight the importance of processing parameters in tailoring their acoustic performance. Full article

Air-penetrating and noise-canceling constructions are required for numerous noise control issues. High ventilation performance conflicts with effective sound insulation, and vice versa. For this reason, ventilated noise barriers are currently being intensively researched and developed. One of the most popular solutions is the louvered-type barrier, whose acoustic efficiency depends on its geometric parameters as well as the acoustic properties of the louvers. One of the main challenges is optimizing the acoustic impedance of louver surfaces in order to achieve maximum reflection, absorption, or minimum transmission of sound waves. This paper proposes an analytical solution to the diffraction problem of a plane sound wave incident on a periodic array of similar thin screens with arbitrary impedance surfaces. An infinite system of linear equations is derived, and its numerical solution allows us to find the reflection and transmission coefficients. It has been shown that screens with reactive impedance are necessary to achieve maximum sound reflection. On the other hand, dissipative screens are required for minimal sound transmission. Additionally, the absorption properties of the array have been studied. It has been found that there is an optimal impedance value that provides the maximum absorption coefficient. Full article