Search Results (122)

In this study, a production method for ceramic shell macrocapsules and a high-temperature-resistant, polymer agent-based self-healing system was developed. Two types of macrocapsules were created by filling hollow ceramic capsules with high-temperature-resistant diallyl phthalate (DAP) resin, known for its thermal stability, and a peroxide-based curing agent. These capsules were incorporated into epoxy and DAP matrix materials to develop polymer composite materials with self-healing properties The macrocapsules were produced by coating polystyrene (PS) sacrificial foam beads with raw ceramic slurry, followed by sintering to convert the liquid phase into a solid ceramic shell. Moreover, FTIR, TGA/DTA, and DSC analyses were performed. According to the thermal analysis results, DAP resin can effectively function as a healing agent up to approximately 340 °C. In addition, quasi-static compression tests were applied to composite specimens. After the first cycle, up to 69% healing efficiency was obtained in the epoxy matrix composite and 63.5% in the DAP matrix composite. Upon reloading, the second-cycle performance measurements showed healing efficiencies of 56% for the DAP matrix composite and 58% for the epoxy matrix composite. Full article

This study used an embedding technique to prepare microcapsules with tea tree oil as the core material and a composite of β-cyclodextrin and nano-montmorillonite as the wall material. The prepared microcapsules were analyzed for their morphological characteristics, thermal stability, and major components. Additionally, the microcapsules’ effect on the quality of and active substances contained in refrigerated strawberries was investigated. The results revealed that the optimal preparation conditions for the microcapsules were a montmorillonite addition of 2% (m/v), a core-to-wall ratio of 1:12 (m/m), an encapsulation temperature of 70 °C, and an encapsulation time of 90 min. Under these conditions, the microcapsules achieved an encapsulation efficiency of 77.67%. The capsules emitted a noticeable aroma of tea tree oil, and their primary components, specifically terpinen-4-ol, 1,8-cineole, p-cymene, and terpinolene, were consistent with those of tea tree oil. The release rate of the microcapsules at 60 °C and 90 °C was significantly lower than that of liquid tea tree oil (p < 0.05). A suitable treatment with tea tree oil microcapsules preserved the appearance and quality of the strawberries, inhibited spoilage during refrigeration, reduced weight loss, maintained firmness, delayed declines in soluble solid contents and acidity in later storage stages, and enhanced the activity of the superoxide dismutase, catalase, and ascorbate peroxidase. The prepared microcapsules also suppressed increases in anthocyanins and inhibited the further maturation of the stored strawberries. The optimal preservative effect was achieved with the placement of 5.0 g of tea tree oil microcapsules per 1.2 L of storage space. Full article

The disadvantage of phase change materials (PCMs) that store thermal energy is their low thermal conductivity. The macro-, micro-, and nanoencapsulation of PCMs are some of the ways to eliminate this drawback. Liquids with micro- and nanometer-sized capsules containing PCMs have become innovative working fluids for heat transfer—a slurry of encapsulated PCMs. This paper shows the results of in-depth studies on the nature of fluid movement (slurry of microencapsulated PCMs) in pipe channels. The slurry flowed inside a tube with a diameter of 4 mm in the range of Re = 350–11,000. The PCM microcapsule (mPCM) concentration ranged from 4.30% to 17.2%. A pressure loss measurement was carried out on a section of 400 mm. The temperature of the flowing slurry was selected so that the PCMs in the microcapsules were in a liquid state and were solid during subsequent measurement series after undergoing a phase transformation. It was found that the boundary of the transition from laminar to turbulent flow is influenced by both the mPCM concentration in the slurry and the state of matter of the PCMs in the microcapsules. The influence of the slurry concentration and the state of matter of the PCMs in the microcapsules on changes such as fluid movement is presented (in terms of the critical Reynolds number). Full article

Background/Objectives: This study aims to develop a solid self-nanoemulsifying drug delivery system (SNEDDS) to enhance the solubility and oral bioavailability of cannabidiol (CBD). Methods: According to the solubility of CBD and pseudo-ternary phase diagrams of the different ingredients, an oil (medium-chain triglyceride, MCT), mixed surfactants (Labrasol, Tween 80), and a co-surfactant (Transcutol) were selected for the SNEDDS. CBD-loaded SNEDDS formulations were prepared and characterized. The optimal SNEDDS was converted into solid SNEDDS powders via solid carrier adsorption and spray drying techniques. Various evaluations including flowability, drug release, self-emulsifying capacity, X-ray diffraction (XRD), differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), morphology, and pharmacokinetic characteristics were conducted. Subsequently, the solid powders with fillers, disintegrants, and lubricants were added to the capsules for accelerated stability testing. Results: The investigations showed that the two S-SNEDDS formulations improved the CBD’s solubility and in vitro drug release, with good storage stability. The pharmacokinetic data of Sprague Dawley rats indicated that a single oral dose of L-SNEDDS and spray drying SNEDDS led to a quicker absorption and a higher Cmax of CBD compared to the two oil-based controls (CBD-sesame oil (similar to Epidiolex^®) and CBD-MCT), which is favorable for the application of CBD products. Conclusions: SNEDDS is a prospective strategy for enhancing the solubility and oral bioavailability of CBD, and solid SNEDDS offers flexibility for developing more CBD-loaded solid formulations. Moreover, SNEDDS provides new concepts and methods for other poorly water-soluble drugs. Full article

The European Union, producing over 2.5 billion tons of waste annually, has prompted the European Parliament to implement legal measures and encourage the shift towards a circular economy. Millions of tons of biowaste from olive plant leaves are generated annually, resulting in environmental and economic challenges. To address this, the biowaste of olive leaves was valorized, resulting in the extraction of valuable components, triterpenes and polyphenols, which hold potential pharmaceutical, food, or cosmetic applications. Our research involved the formulation of a triterpene extract (TTP70, 70% triterpenes) as a solid dispersion using Poloxamer-188 (P188) and Poloxamer-407 (P407). The solid dispersions were prepared using a kneading method and various extract-to-polymer weight ratios, including 1:1, 1:2, and 1:5. The influence of hydrophilic carriers on the solubility, dissolution profile, and in vitro passive permeability of TTP70 was evaluated. Both carriers and all considered weight ratios significantly improved the solubility of hydrophobic extract and the dissolution of triterpenes. PAMPA experiments demonstrated the efficacy of the formulation in improving the passive permeation of triterpenes. Subsequently, the solid dispersions were physically mixed with a polyphenol-enriched extract (OPA40, 49% of polyphenols) also obtained from olive leaves, and they were used to fill hard gelatin capsules and produce an oral dosage form. The composite formulations improved the dissolution of both classes of constituents. Full article

Sample preparation is broadly recognized as the most critical, time-consuming, and error-prone step of a bioanalytical workflow. Over the years, the development of pretreatment methods aimed at the isolation and preconcentration of the target analytes from sample matrices has been an ongoing effort. Recent innovations have aimed at miniaturizing sample preparation to streamline laboratory processes and enhance analytical performance. Sorbent-based microextraction techniques, including solid-phase microextraction, microextraction by packed sorbent, bar adsorptive microextraction, capsule phase microextraction, etc., have recently gained attention as effective sample preparation tools prior to gas chromatography-mass spectrometric analysis. This article provides an overview of the bioanalytical GC-MS applications of sorbent-based techniques published in the last decade (2014–2024) that enable the efficient and sensitive determination of various compounds in biological samples. Full article

Background: The purpose of this study was to detect proteomic alterations and corresponding signaling pathways involved in the formation of age-related cataract (ARC), diabetic cataract (DC), and post-vitrectomy cataract (PVC). Methods: Three sample types, the aqueous humor (AH), the anterior capsule (AC), and the content of the phaco cassette, were collected during phacoemulsification surgery. The samples were obtained from 12 participants without diabetes mellitus (DM), 11 participants with DM, and 7 participants without DM, with a history of vitrectomy surgery in the past 12 months. The Sp3 protocol (Single-Pot, Solid-Phase, Sample-Preparation) was used for the sample preparation. The recognition and quantification of proteins were carried out with liquid chromatography online with tandem mass spectrometry. The DIA-NN software was applied for the identification and quantification of peptides/proteins. Statistical analysis and data visualization were conducted on Perseus software. Data are available via ProteomeXchange. Results: A very rich atlas of the lens and AH proteome has been generated. Glycosaminoglycan biosynthesis and the non-canonical Wnt receptor signaling pathway were differentially expressed in ARC compared to both the DC and PVC groups. In the PVC group, complement activation was differentially expressed in AH samples, while glutathione metabolism and oxidoreductase activity were differentially expressed in AC samples. Microfilament motor activity, microtubule cytoskeleton organization, and microtubule binding were differentially expressed in the DC and PVC groups in both AH and AC samples. Conclusions: The results of this study expand the existing knowledge on pathways involved in the pathophysiology of cataract, and suggest possible important druggable targets for slower progression or even prevention of cataract. Full article

Background: Several artificial intelligence systems based on large language models (LLMs) have been commercially developed, with recent interest in integrating them for clinical questions. Recent versions now include image analysis capacity, but their performance in gastroenterology remains untested. This study assesses ChatGPT-4’s performance in interpreting gastroenterology images. Methods: A total of 740 images from five procedures—capsule endoscopy (CE), device-assisted enteroscopy (DAE), endoscopic ultrasound (EUS), digital single-operator cholangioscopy (DSOC), and high-resolution anoscopy (HRA)—were included and analyzed by ChatGPT-4 using a predefined prompt for each. ChatGPT-4 predictions were compared to gold standard diagnoses. Statistical analyses included accuracy, sensitivity, specificity, positive predictive value (PPV), negative predictive value (NPV), and area under the curve (AUC). Results: For CE, ChatGPT-4 demonstrated accuracies ranging from 50.0% to 90.0%, with AUCs of 0.50–0.90. For DAE, the model demonstrated an accuracy of 67.0% (AUC 0.670). For EUS, the system showed AUCs of 0.488 and 0.550 for the differentiation between pancreatic cystic and solid lesions, respectively. The LLM differentiated benign from malignant biliary strictures with an AUC of 0.550. For HRA, ChatGPT-4 showed an overall accuracy between 47.5% and 67.5%. Conclusions: ChatGPT-4 demonstrated suboptimal diagnostic accuracies for image interpretation across several gastroenterology techniques, highlighting the need for continuous improvement before clinical adoption. Full article

This study investigates the quality characteristics and healing performance of precast concrete incorporating self-healing technology, with the aim of supporting smart city implementation. To enhance the self-healing capabilities of concrete, hybrid self-healing capsules, combining solid capsules and liquid capsules, were utilized, and their applicability and practicality were assessed. The findings revealed that incorporating hybrid self-healing capsules into precast concrete resulted in a reduction in slump by up to 14% and air content by up to 9%. Furthermore, the addition of hybrid capsules led to a maximum reduction in compressive strength of 16% and flexural strength of 18% at 28 days, while demonstrating an increase in healing efficiency as the capsule content increased. The results also indicated that the use of hybrid capsules enhanced the healing efficiency by approximately 16%, 25%, and 32% for mixing ratios of 1%, 3%, and 5%, respectively, with the overall healing efficiency ranging between 75% and 90%. Additionally, the interaction between the hybrid capsules and natural healing mechanisms promoted crystal formation around cracks, thereby significantly improving the long-term durability of the concrete. Full article

Background: Lake Al-Asfar in KSA was used as a sink for wastewater for decades and suffered from pollution. The lake is a habitat to different microbial species that play important ecological roles, some of which are good, and some are bad and even pathogenic. In a previous investigation, algal-bacteria consortia have proven to be beneficial in bioremediating heavy metals and hydrocarbons in Lake Al-Asfar. The identity of algae was revealed to be Chlorella sp. and Geitlernema sp. in the consortia. The identity of the heterotrophic bacterial partners, on the other hand, awaits investigation and is addressed in the present research. On the other hand, investigating the diversity of Protozoa and parasites is also tackled as they represent indicators of pollution. Some pose serious health risks, but some of them also contribute to reducing some of the pollution levels. Methods: Bacteria associated with algae were isolated in pure form. The polyphasic approach was used to identify bacterial samples, including staining procedures, the use of Vitek technology, and scanning electron microscopy. This information was integrated with structure information such as capsule presence, endospore formation, and wall characteristics indicated by Gram stain. With regard to protists including Protozoa and parasites, Light microscopy and taxonomic books of identification were used to reveal their identity. Results: three main bacterial strains belonging to the following genera were identified: Sphingomonas, Rhizobium, and Enterbacter. The last is potentially pathogenic and poses health risks to Lake goers. Rhizobium, on the other hand, is most likely found in the lake from agricultural wastewater and is a nitrogen fixer that increases the fertility of crops. The first bacterium is associated with special lipid metabolism and is hardly pathogenic. Several diverse microscopic forms of protists, mainly Protozoa and parasites, were identified, which included Entamoeba histolytica, Balantidium coli, Ascaris lumbricoides, Amoeba, Paramecium, Euglena, and Gymnodinium sp. Discussion: The three types of bacteria identified have metabolic activities that are associated with bioremediation. On the other hand, protists, including Protozoa and parasites, are regular members of wastewater communities and help in scavenging solid wastes, but they cause hazards such as secreting toxins, causing disease, and impacting the bioremediation potential by feeding on beneficial bioremediating algae and bacteria. This is part of the wastewater ecosystem dynamics, but efforts must be exerted to minimize, if not completely eliminate, pathogenic parasites in order to maximize the growth of algal consortia. Conclusions: Vitek technology is an emerging less time- and effort-consuming fast technology for identifying bacteria. Bacteria identified have significant ecological bioremediating roles, together with their algal partners, but some pose pathogenic risks. Identifying co-inhabitants like protists and parasites helps to shed light on their impact on one another and pave the way for restoration efforts that minimize the biological hazards and maximize the use of beneficial local microorganisms. Full article

Background/Objectives: Renal cell carcinoma is an aggressive form of kidney cancer, contributing to an estimated 138,000 deaths globally in 2017. Traditional treatments like chemotherapy and radiation are generally considered ineffective. Additionally, CD47 has been identified as a crucial tumor antigen involved in the development and progression of various cancers, including renal cell carcinoma. The interaction of CD47 with SIRPα triggers a “don’t eat me” signal to the macrophages, inhibiting phagocytosis. Much progress has been made in targeting CD47 for cancer immunotherapy in solid tumors (STs) and hematological malignancies. This study aimed to evaluate CD47 expression in malignant and benign renal cell tumors and compare it with prognostic histopathological parameters. Methods: We included 160 malignant and 26 benign tumors. The malignant tumors consisted of renal cell carcinoma (RCC) subtypes including 37 clear cell, 30 chromophobe, 30 papillary type 1, 29 papillary type 2, and 34 unclassified RCC cases. As for the benign tumors, we included 26 oncocytoma cases. All samples were stained with anti-CD47 antibodies by immunohistochemistry methods. Results: The statistical analysis yielded a significant correlation between CD47 expression and survival, metastasis, and capsule invasion for the unclassified RCC cases. We did not find any further significant correlation between CD47 expression and the studied parameters. Conclusions: To the best of our knowledge, our study is the first to research CD47 expression in benign and malignant renal carcinoma subtypes. Further large-scale studies are needed to determine the expression profile of CD47 in renal cell tumors. Full article

This work presents the synthesis, purification, and characterization of a molten salt fuel for the irradiation experiment SALIENT-03 (SALt Irradiation ExperimeNT), a collaborative effort between the Nuclear Research and Consultancy Group and the Joint Research Centre, European Commission. The primary objective of the project is to investigate the corrosion behavior of selected Ni-alloy based structural materials which are being considered for the construction of fluoride molten salt reactors. During the test, these materials will be exposed to selected liquid molten fuel salts under irradiation in the High Flux Reactor in Petten, the Netherlands. In addition, the properties and distribution of the fission products formed in the fuel salt during burn-up will be studied by various post irradiation examinations. In the SALIENT-03 fuel, U and Pu fluorides, as fissile material, are dissolved in a carrier melt based on a 78⁷LiF-22ThF₄ eutectic mixture to form fuel salts with four different compositions, containing PuF₃, UF₄, UF₃, and CrF₃. This article comprehensively describes all the steps of this fuel synthesis process: the synthesis of the required pure fluoride powders (⁷LiF, ThF₄, UF₄, UF₃, and PuF₃); the mixing, melting, and purification of the different fuel salt compositions; and the fabrication of solid ingots to be loaded into the irradiation capsules. The characterization of the intermediate and final products is also carried out, following a rigorous quality assurance protocol. The quality assurance is achieved using an analytical scheme consisting of mass balance-based conversion efficiency evaluation, X-ray diffraction, and differential scanning calorimetry analyses. All experimental goals were successfully achieved, highlighting promising prospects for advancing future research and development regarding fuel production methods for fluoride-based molten salt reactors. Full article

Oleogels (organogels) are systems resembling a solid substance based on the gelation of organic solvents (oil or non-polar liquid) through components of low molecular weight or oil-soluble polymers. Such compounds are organogelators that produce a thermoreversible three-dimensional gel network that captures liquid organic solvents. Oleogels based on natural oils are attracting more attention due to their numerous advantages, such as their unsaturated fatty acid contents, ease of preparation, and safety of use. As a result of the research, two oleogels were developed, into which freeze-dried alginate carriers with a probiotic, L. casei, were incorporated. Two techniques were used to produce probiotic-loaded capsules—extrusion and emulsification. Alginate beads obtained by the extrusion process have a size of approximately 1.2 mm, while much smaller microspheres were obtained using the emulsification technique, ranging in size from 8 to 17 µm. The trehalose was added as a cryoprotectant to improve the survival rate of probiotics in freeze-dried alginate carriers. The encapsulation efficiency for both of the methods applied, the emulsification and the extrusion technique, was high, with levels of 90% and 87%, respectively. The obtained results showed that the production method of probiotic-loaded microspheres influence the bacterial viability. The better strain survival in the developed systems was achieved in the case of microspheres produced by the emulsification (reduction in bacterial cell viability in the range of 1.98–3.97 log in silica oleogel and 2.15–3.81 log in sucragel oleogel after 7 and 30 days of storage) than by the extrusion technique (after a week and a month of oleogel storage, the decrease in cell viability was 2.52–4.52 log in silica oleogel and 2.48–4.44 log in sucragel oleogel). Full article

An ice slurry or an emulsion of a phase change material (PCM) is a multiphase working fluid from the so-called Latent Functional Thermal Fluid (LFTF) group. LFTF is a fluid that uses, in addition to specific heat, the specific enthalpy of the phase change of its components to transfer heat. Another fluid type has joined the LFTF group: a slurry of encapsulated phase change material (PCM). Technological progress has made it possible for the phase change material to be enclosed in a capsule of the size of the order of micrometers (microencapsulated PCM—mPCM) or nanometers (nanoencapsulated PCM—nPCM). This paper describes a method for determining the Reynolds number (Re) at which the nature of the flow of the mPCM slurry inside a straight pipe changes. In addition, the study results of the effect of the concentration of mPCM in the slurry and the state of the PCM inside the microcapsule on the value of the critical Reynolds number (Re_cr) are presented. The aqueous slurry of mPCM with a concentration from 4.30% to 17.20% wt. flowed through a channel with an internal diameter of d = 4 mm with a flow rate of up to 110 kg/h (Re = 11,250). The main peak melting temperature of the microencapsulated paraffin wax used in the experiments was around 24 °C. The slurry temperature during the tests was maintained at a constant level. It was 7 °C, 24 °C and 44 °C (the PCM in the microcapsule was, respectively, a solid, underwent a phase change and was a liquid). The experimental studies clearly show that the concentration of microcapsules in the slurry and the state of the PCM in the microcapsule affect the critical Reynolds number. The higher the concentration of microcapsules in the slurry, the more difficult it was to maintain laminar fluid flow inside the channel. Furthermore, the laminar flow of the slurry terminated at a lower critical Reynolds number when the PCM in the microcapsule was solid. Caution is advised when choosing the relationship to calculate the flow resistance or heat transfer coefficients, because assuming that the flow motion changes at Re = 2300, as in the case of pure liquids, may be an incorrect assumption. Full article

Objective: To evaluate and project the shelf life of GLPG4399, an early-phase clinical drug formulation by applying the Accelerated Stability Assessment Program (ASAP) approach. Methods: Forced degradation conditions were implemented to identify the stability-limiting degradation product. The drug and its degradation products were separated using a validated liquid chromatography method. Then, the selected clinical capsule formulation was placed in a glass vial and exposed to accelerated short-term conditions of combinations of high- and low-level heat and humidity in an open state for 5 weeks. The liquid chromatography results were evaluated using the ASAP, which is based on the moisture-modified Arrhenius principle. The resulting data were fitted using a suitable diffusion kinetics method. Results: The developed model was applied to predict the shelf life of the drug product when using clinically appropriate primary packaging (high-density polyethylene container). The derived stability parameters of the moisture-modified Arrhenius equation were the Arrhenius collision frequency, activation energy, and humidity sensitivity constant. The goodness of fit parameters R² (>0.95) and goodness of prediction Q² (>0.80) parameters for the selected model were acceptable. The results of the accelerated, short-term stability study were verified against real-time, long-term 12-month data. Conclusions: We demonstrated the application of the ASAP approach to evaluate the shelf life of a GLPG4399 solid capsule formulation. The studied ASAP approach can be extended to evaluate the stability and shelf-life estimations of other early-phase clinical formulations. Full article