Search Results (14)

Large deformation is one of the most critical hazards in tunnels excavated under complex geological conditions. It often causes significant economic losses and threatens construction safety. For layered soft rock tunnels subjected to high in situ stress, the deformation and failure mechanisms are largely governed by the bedding dip angle. To clarify these mechanisms and optimize the corresponding construction control measures, this study investigates a carbonaceous slate section of a railway tunnel in the Western Sichuan Plateau. Field monitoring and FLAC3D numerical modelling are coupled. The influence of the bedding dip angle on the plastic-zone evolution and the failure modes of the surrounding rock is analysed. The micro-bench, three-bench, and reserved core soil methods, together with the rock bolt length, are comparatively evaluated. On this basis, a differentiated reinforcement strategy is proposed for bedding-induced asymmetric loading. The results indicate that: (1) The bedding dip angle governs the failure mode of the surrounding rock. Under the micro-bench method, the plastic zone in subvertically bedded rock masses exhibits a quasi-symmetrical distribution along the normal direction of the bedding planes. The sidewalls predominantly undergo flexural failure. In contrast, under bedding-induced asymmetric loading, the plastic zone concentrates at the left springline and right shoulder. An asymmetric composite failure mode is formed, characterized by shallow flexural–tensile cracking and deep-seated interlayer shear. (2) Under the subvertical bedding condition (89°), the reserved core soil method mitigates the excavation-induced unloading disturbance most effectively. It achieves the lowest peak stress and the smallest tunnel convergence, which is 15.7% and 33.0% lower than those of the micro-bench and three-bench methods, respectively. Its plastic zone reaches full numerical convergence. The reserved core soil method is therefore identified as the optimal excavation Scenario under this condition. (3) The rock bolt length exhibits a threshold effect on deformation control. The most substantial improvement occurs when the bolt length is increased from 4 m to 6 m, beyond which the benefit tends to plateau. A bolt length of 6 m is therefore recommended as the best-performing Scenario among the tested values (4, 6, 8, and 10 m) for the investigated geological and support conditions. For surrounding rock subjected to bedding-induced asymmetric loading, a differentiated reinforcement strategy targeting the vulnerable zones reduces the maximum deformation by 18.8% and 28.3% compared with the uniform reinforcement Scenario and the baseline Scenario, respectively. These findings provide practical insights into excavation-method selection and support optimization for layered soft rock tunnels under similar conditions. Full article

Tunnel construction in soft soil environments involves significant geological and hydraulic uncertainty, particularly where permeable sandy interlayers within soft clay are prone to seepage-induced instability and excessive settlement. Although hydraulic–mechanical coupling is widely recognized, the spatial variability of key soil parameters (e.g., permeability and elastic modulus) is often inadequately represented, limiting quantitative evaluation of heterogeneous ground effects on construction-induced deformation. In this study, statistical analyses of site investigation and monitoring data are conducted to characterize parameter distributions and transverse settlement trough morphology, supporting model validation. A fluid–solid hydro-mechanical coupled numerical model in ABAQUS demonstrates that groundwater flow increases maximum surface settlement from 3.18 cm to 3.58 cm, confirming the significance of hydraulic coupling. To quantify spatial variability effects, a stochastic finite element framework based on random field theory is developed, showing that variations in vertical correlation length influence both the mean and dispersion of maximum settlement. Specifically, under a settlement control threshold of 40 mm, the failure probability decreases from 24.21% to 1.01% as the vertical correlation length increases from 1.5 m to 6 m. Finally, an engineering-oriented risk assessment framework is established using settlement trough area as the core loss indicator; its lognormal distribution is verified, and failure probability and reliability indices are integrated with code-based thresholds to evaluate construction risk under different scenarios, with the resulting risk levels ranging from Relatively High (Level III) to Moderate (Level II). Full article

Highways constructed on stratified foundations with thick soft soil interlayers in the Yellow River floodplain of Shandong Province have experienced long-term settlement. However, accurately predicting subgrade settlement caused by the secondary consolidation of soft soils remains a major engineering challenge. In this study, PLAXIS 3D numerical simulation was combined with a neural network model to predict the long-term temporal and spatial settlement behavior of highway subgrades. The results show that the soft soil creep (SSC) constitutive model better represents the consolidation process of the soft soil interlayer than the soft soil (SS) model. A decrease in permeability will prolong the dissipation time of excess pore water pressure and the settlement stabilization time, leading to an increase in the proportion of post-construction settlement in the total settlement. The final settlement increases linearly with the thickness of the soft soil interlayer and embankment height, while it decreases following a power-law function with increasing interlayer burial depth. By comprehensively considering the combined effects of multiple factors, a genetic algorithm–optimized backpropagation neural network (GA-BP) model was developed. The testing dataset achieved a root mean square error (RMSE) of 0.01488 m, a mean absolute percentage error (MAPE) of 7.0562%, and a coefficient of determination (R²) of 0.9706, demonstrating the model’s ability to achieve intelligent full-period and full-section settlement prediction for subgrades with soft soil interlayers. Overall, this study developed an intelligent framework for predicting long-term settlement in subgrades with soft soil interlayers, offering practical guidance for evaluation and timely settlement control. Full article

With advantages in efficiency and sustainability, assembly splicing technology promotes construction industry upgrading. However, research on the seismic response of assembly splicing subway stations (ASS) is particularly scarce. This work studies the asymmetric ASS in soft soil, establishing a refined finite element model with soil–structure interactions. Three seismic records with different frequency characteristics are applied for nonlinear incremental dynamic analysis. Based on the seismic records that produce the most unfavorable seismic response, this research is conducted on the damage distribution characteristics and the mechanical responses. In addition, the influence of the splicing response at different locations on the interlayer displacement and internal forces of structures is systematically studied. The results indicate that when seismic records with low-frequency characteristics are inputted, the ASS structure in soft soil develops into the most unfavorable state. Under strong seismic action, the top joint of the sidewall exhibits significant horizontal sliding and opening, making key areas of weak seismic performance. It also indicates that the interface contact between precast and cast-in-place components is the primary factor that is causing internal force redistribution. This study provides a reference for performance-based seismic design of ASS in soft soil. Full article

The Zigui Basin, located in the Three Gorges Reservoir Area, has developed numerous landslides due to its interlayering of sandstone and mudstone, geological structure, and reservoir operations. This study identifies a fourth type of landslide failure mode: an oblique-dip slope wedge (OdSW) landslide, based on the Wanshuitian landslide. Following four heavy rainfall events from 3 to 13 July 2024, this landslide exhibited significant deformation on the 17th and was completely destroyed within 40 min. The dimensions of the landslide were 350 m in length, 160 m in width, and 20 m in thickness, with a volume estimated at 8.0 × 10⁵ m³. The characteristics of landslide deformation and the changes in moisture content within the shallow slide body were ascertained using unmanned aerial vehicles, moisture meters, and mobile phone photography. The landslide was identified to have occurred within the weathered residual layer of mudstone, situated between two sandstone layers, with the eastern boundary defined by an inclined rock layer. Upon transitioning into the accelerated deformation stage, the landslide initially exhibited uniform overall sliding deformation, culminating in accelerated deformation destruction. The dip structure created terrain disparities, resulting in a step-like terrain on the left bank and gentler slopes on the right bank, with interbedded soil and rock in a shallow layer, because the interlayered soft and hard geological conditions caused varied weathering and erosion patterns on the riverbank slopes. The interbedded weak–hard stratum layer fostered the development of the oblique-dip slope wedge landslide. Based on the improved Green–Ampt model, we developed a stability prediction methodology for an oblique-dip slope wedge landslide and determined the rainfall infiltration depth threshold of the Wanshuitian landslide (9.8 m). This study aimed not merely to sharpen the evolution mechanism and stability prediction of the Wanshuitian landslide but also to formulate more effective landslide-monitoring strategies and emergency management measures. Full article

Due to the complexity of planning and constructing underground lines, construction challenges—such as close proximity and multi-line interactions—are increasingly being recognized, along with their associated safety hazards. The visual observation of tunnel deformation and changes in the surrounding strata is difficult. In this study, laboratory model experiments were conducted using a mixture of liquid paraffin, n-tridecane, and silica gel powder, combined in specific proportions to create a transparent material that simulates natural soft rock. The new tunnel was designed to simultaneously cross over and under two existing tunnels. The impact of the new tunnel on the existing tunnels was examined, with excavation length and soil layer thickness considered as the primary influencing factors. The results indicate that excavating the new tunnel causes settlement deformation in the tunnels above and heave deformation in the tunnels below. The magnitude of deformation increases as excavation progresses but decreases with the greater thickness of the soil interlayer. For an existing tunnel, variations in the thickness of the soil interlayer not only affect its own deformation but also disturb the tunnel on the opposite side. Therefore, to ensure safer and orderly urban tunnel construction and to address the “black box” effect, it is essential to study the deformation characteristics of existing tunnels and their surrounding rock during the construction of new tunnels. Full article

As a new rock breaking method, CO₂ transient cracking has been widely used in rock excavation projects in recent years. However, in the actual construction process, there are often situations where the fracturing effect varies due to different rock mass structures. Through theoretical analysis and on-site cracking tests, this article studies the effect of CO₂ transient cracking under the control of different rock mass structures. The results show that: (1) the dynamic compressive strength of rock directly determines the number and range of dynamic impact fractures; the original fractures of rock mass and those caused by dynamic impact in the first stage jointly determine the effect of high-pressure gas expansion in the second stage. (2) The arrangement of holes along the strata is conducive to the action of high-pressure expanding gas along the soft structural plane in the rock mass, which is conducive to the fracturing of the rock mass; the amount of crack formation is small, but the influence range is large. (3) The cracking effect of carbon dioxide transient cracking applied to massive rock mass is better than that of monolithic rock mass, while the cracking effect of layered rock mass with soil interlayer is poor. The research results are of great significance for improving the effectiveness of carbon dioxide transient-induced cracking excavation and guiding actual construction. Full article

After coupling long-period seismic motions with the soil–structure interaction (SSI) effect, isolated structures can easily be resonated, and the seismic response of the structure is significantly enhanced. The SSI effect can alter the dynamic characteristics of a structure, resulting in a deviation between the assumed seismic-isolation effect of the rigid foundation and the theoretical results. To investigate the dynamic characteristics and seismic-response laws of interlayer structures considering SSI under long-term seismic motion, four types of ground motions (near-field ordinary, far-field ordinary, near-field pulse, and far-field harmonic ground motions) were selected, and two structural models (rigid-foundation and soft soil foundation interlayer seismic-isolation structure models) were established. Experiments were conducted using a combination of shaking-table tests and finite-element simulations. The results show that the use of the SSI effect caused the decrease in the acceleration response of the upper structure of both models under four types of seismic motions and increased the seismic peak ground acceleration (PGA). In addition, the weakening of the acceleration response of the upper structure under ordinary seismic motion is significant for longer periods of seismic motion. Furthermore, when considering the SSI effect, the displacement response ratio under long periods and ordinary ground motions is greater than that of rigid foundations, and the horizontal deformation of the isolation layer under long-period ground motions is greater than that under ordinary ground motions. This shows that the SSI effect weakens the interlayer shear force under ordinary seismic action more than that under long-period seismic action. When PGA increases, the interlayer shear force response of the interlayer isolation structure model with a soft soil foundation under a long-period seismic action may be smaller than that of the rigid-foundation model. Full article

Assuming that the ground anchor is connected with the rock–soil of the sidewall by a tangential linear spring, the load transfer model of the fully grouted ground anchor is established by using the spring element method, and the analytical solutions of the displacement, axial force, and shear stress distribution of the ground anchor in the upper and lower parallel strata foundation and sandwich foundation are given, respectively. Corresponding to the above two kinds of alternating strata, the mechanical behavior of the vertical fully grouted ground anchor in the soft–hard alternating stratum is analyzed using the four conditions in Case 1 and the six conditions in Case 2, respectively. Through the case analysis, it can be concluded that the mechanical behavior of the round anchor is greatly affected by the shear modulus of the shallow stratum, and is less affected by the shear modulus of the deep stratum. The depth of the stratum interface and the thickness of the interlayer have some influence on the mechanical behavior of the whole ground anchor but have little influence on the displacement and axial force distribution of the ground anchor. This paper has certain guidance and reference significance for the design of vertical fully grouted ground anchors in the alternating strata. Full article

With the rapid development of road engineering today, a large number of high-grade highways need to pass through expansive soil distribution areas. At present, the research on expansive soil slope mainly focuses on the newly excavated cutting slope. However, according to engineering experience, a landslide of fill embankment on expansive soil foundation is also very common. The expansive soil layer is heterogeneous. There are many weak intercalations or large fissures under the ground, which are generally parallel to the trend, with low strength and high permeability. After rainfall, the strength of the weak interlayer and large fissures will be further reduced after moisture absorption, and the sliding surface is easily formed under the load of filler, which is the main factor inducing embankment landslide. On the basis of landslide investigation and a laboratory test, a FORTRAN calculation program is developed in this paper, which can comprehensively consider the special moisture absorption and softening characteristics of expansive soil. Taking a high fill embankment slope with a soft interlayer in the Baoshan area of Yunnan Province as an example, the stability and instability characteristics of the fill slope on the expansive soil foundation are analyzed, and the influence of moisture absorption and softening on the expansive soil slope is emphatically discussed. Finally, this paper puts forward the reinforcement method of the high fill embankment slope on the soft expansive soil foundation, which is proven to have a good reinforcement effect through calculation analysis and field practice. For expansive soil foundation with weak interlayer, it is better to directly reinforce the weak layer through rigid piles. Full article

Soft soil is widely distributed in the riverside area of southern China. The creep deformation characteristics of the soft soil affect the long-term stability of the structure foundation, which cannot be ignored. Through the triaxial drainage creep test, the creep characteristics of riverside soil with a soft interlayer from Jiangsu Province were studied. The test results show that the creep procedure of the soft soil is divided into two stages, exhibiting steady-state creep and shear shrinkage characteristics with time and stress growth, which presents typical nonlinear behavior. Additionally, the confining pressure and stress are critical factors affecting creep characteristics. The fractal dashpot based on fractal derivative theory is introduced in place of the Abel dashpot in the classical fractional Burgers model; a fractal Burgers creep model with few parameters, high precision, and clear physical significance is established. Additionally, an analytical solution to the creep model is given. The model parameters are determined by fitting the test results, and the comparison shows that the results estimated with the model are more accurate than those estimated with the traditional model. The sensitivity analyses of the model parameters reveal the influence of key parameters on the creep characteristics of the soil. The results further confirm that the proposed fractal Burgers model can characterize the creep behavior of viscoelastic soil. These observations are extremely important for predicting the foundation displacement and formulating measures to prevent the deformation, which can provide a reference for engineering applications in the riverside area of southern China. Full article

High-speed railways are built in deep soft-soil foundations interlayered with hard materials. However, the hard layers cannot be penetrated by conventional foundation treatment. Moreover, the project cost is sometimes prohibitive, which is an issue for post-construction subsidence control. The bag grouting pile is a special grouting-pile-reinforcement technique for treating soft-soil foundations interlayered with hard materials. This paper conducted tests on the Ningbo-Taizhou-Wenzhou ballast track passenger railway, combining a conventional mixing-pile-foundation (not through hard layer) processing station and the bag-grouting-pile-processing subgrade line. Using field tests combined with numerical calculation, the lateral displacement, settlement and pile–soil stress were tested to obtain the working properties of the grouting-pile-composite foundation. The variation in the law of lateral displacement, settlement, and pile–soil stress of the foundation was studied. The results showed that the post-construction subsidence of bag-grouting-pile- and conventional mixing-pile-foundation control was less than 15 cm and 30 cm, respectively, which met the design requirements. The results also showed that the design scheme was reasonable (load-sharing ratio of bag-pile-foundation pile soil-based test was reasonable). The numerical calculation showed a change in pile diameter. It also showed that pile spacing could not improve subsidence-control properties, bag grouting pile can promote pore-pressure dissipation and accelerate consolidation, and pile spacing can be increased to cut project costs incurred by the pile-bearing capacity. Full article

The existence of local soft interlayer can significantly amplify or attenuate the ground motion and thus might influence the lagged spatial coherency between spatially varying earthquake ground motions. A target site with a local soft interlayer was assumed first, and then two numerical examples were set. In example 1, linear soil behavior was considered and a large amount of quasi-stationary spatially varying earthquake ground motions were generated by combining the one-dimensional wave propagation theory and the classical spectral representation method. The influence regularity of varying shear wave velocity, buried depth, and thickness of the soft interlayer on the characteristics of lagged spatial coherency was investigated. In example 2, non-linear soil behavior was taken into account and fully non-stationary spatially varying earthquake ground motions were thus generated by using time-varying transfer function and spectral representation method. An overall evaluation was carried out to shed light on the differences of characteristics of spatial coherency between non-linear soil and linear soil cases. It showed that: (i) As the shear wave velocity of interlayer declines and as the buried depth and thickness increase, remarkable reduction of spatial coherency showed up; (ii) the reduction of lagged spatial coherency caused by varying buried depth may be more inclined to concentrate in the lower frequency range; (iii) the non-linear soil behavior can cause greater further reduction of lagged spatial coherency in comparison with linear soil behavior, especially in the higher frequency range; (iv) the troughs of lagged spatial coherency curve tend to be located in the variation range of vibration frequency of time-varying spectral ratio. Full article

The marine clays located in the Southeast area of China are characterized by their higher water content, higher compressibility and higher salinities. This soil is mainly composed of illite/montmorillonite interlayer minerals. Previous research has shown that the saline water significantly influences the liquid limit and other physical characteristics of the clays. As the desalination of pore water occurs as a result of freshwater or rainfalls, the physical and mechanical behaviors of the soft marine clays changes, and this can lead to potential hazards for infrastructure. Therefore, it is essential to understand the effects of chemistry variations and to predict the long-term foundation deformations. Based on previous works, the deformation behavior of artificial soils corresponding to a mixture of kaolinite and bentonite (the mass ratios of bentonite were 0%, 5%, 10% and 20%) was further discussed in a ln(1 + e)-logp’ system. The permeabilities of the samples mixed with different concentrations of sodium chloride solutions were compared based on oedometer tests. The micro-structures in the samples were investigated by SEM (scanning electronic microscopy) tests. The declining trend of a newly defined volume compression index C_cv and swelling index C_sv with pore water salinity and e₀/e_L was observed when the initial void ratios e₀ of the samples were close. The permeability coefficient k and the slopes C_k = e/logk of the mixtures increased with the ionic concentrations. Finally, the changes in volume deformations and permeabilities induced by sodium chloride solution are discussed based on ‘suction pressure’ and initial void compression at micro-level. This paper proves that the influences of salinity on the mechanical behavior of clays are mainly attributable to the interaction between diffused double layers, and these findings are helpful for improving the constitutive model of soft clays when taking pore water chemistry changes into consideration. Full article