Search Results (31)

Silicon is the most commonly used material in the electronic industries due to its unique properties, which also make it very difficult to machine using conventional machining. Electrical discharge machining (EDM) is a non-traditional process that is gaining popularity for machining silicon, although a slower machining rate is one of its limitations. This study investigates two electrode design strategies to enhance the efficiency of EDM by improving the material removal rates, reducing tool wear, and refining the quality of machined features. The first approach involves using graphite electrodes in various array configurations (1 × 4 to 6 × 4) and leg heights (0.2″ and 0.3″). The second approach employs hollow electrodes with differing wall thicknesses (0.04″, 0.08″, and 0.12″). The effects of these variables on performance were evaluated by maintaining constant EDM parameters. The results indicate that increasing the number of electrode legs improves the flushing conditions, resulting in shorter machining times. Meanwhile, the shorter electrode height outperforms the taller electrode, providing a higher machining speed. The thinnest wall thickness for hollow electrodes yielded the best performance due to the increased energy distribution. Both electrode design methodologies can be used for the mass fabrication of features with targeted profiles on silicon using the die-sinking EDM process. Full article

This research outlines the design of capacitive pressure sensors fabricated from three biocompatible materials, featuring both circular and square geometries. The sensors were structured with a dielectric layer positioned between gold-plated electrodes at the top and bottom. Their performance was assessed through simulations conducted with ANSYS Workbench. Of the various sensor configurations tested, the circular design that included two crescent-shaped slots and a 20 µm thick PDMS dielectric material demonstrated the highest sensitivity of 10.68 fF/mmHg. This study further investigated the relationship between resonant frequency shifts and arterial blood pressure, revealing an exceptionally linear response, as evidenced by a Pearson’s correlation coefficient of −0.99986 and an R-squared value of 0.99972. This confirmed the sensor’s applicability for obtaining precise blood pressure measurements. Additionally, a 3 × 30 mm cobalt–chromium (Co-Cr) stent was obtained, and its inductance was measured using an impedance analyzer. Full article

Slot-die coating is widely used in the preparation of negative electrodes for lithium batteries. The thickness of the negative electrode has a significant influence on the battery performance and lifespan, and different manufacturers have different requirements for its thickness. In order to reduce the waste caused by trial and error in the electrode preparation process, a prediction model for the negative electrode thickness was established and verified through simulation and experiments. Based on the Landau–Levich film equation and the Ruschak model, a high-precision prediction model was constructed by taking into account the influence of factors’, such as temperature and slurry, spreading characteristics on the coating thickness. The minimum coating thickness and its influencing factors were explored. Meanwhile, the simulation analysis of the coating thickness was performed, and the theoretical values of three common process parameters were compared with the simulation results, showing a deviation of only 2.9%. An experiment on predicting the thickness of the negative electrode of lithium batteries was conducted. Thickness measurements were performed on the samples prepared through the experiment and compared with theoretical values. The accuracy rate of this thickness prediction model can reach 98.75%. Full article

Silver nanowire transparent conductive films (AgNW TCFs), as the novel transparent electrode materials replacing ITO, are anticipated to be applied in numerous optoelectronic devices, and slot-die coating is currently acknowledged as the most suitable method for the mass production of large-sized AgNW TCFs. In this study, sodium carboxymethyl cellulose (CMC) and polyvinyl alcohol (PVA), as film-forming aids, and AgNWs, as conductive materials, were utilized to prepare a specialized AgNW ink, and a slot-die coating is employed to print and prepare AgNW TCFs. The optoelectrical properties of AgNW TCFs are optimized by adjusting the compositions of AgNW ink and the process parameters of slot-die coating. The suitable compositions of AgNW ink and the optimal parameters of slot-die coating are a CMC type of V, a PVA volume of 1 mL, a AgNW volume of 1.5 mL, a volume ratio of 30 and 45 nm AgNWs (2:1), and a coating height of 400 μm. The resultant AgNW TCFs achieve excellent comprehensive optoelectronic performance, with a sheet resistance of less than 50 Ω/sq, a visible light transmittance exceeding 92%, and a haze below 1.8%. This research provides a valuable approach to producing AgNW TCFs on a large scale via the slot-die coating. Full article

In recent years, third-generation solar cells have experienced a remarkable growth in efficiency, making them a highly promising alternative energy solution. Currently, high-efficiency solar cells often use top electrodes fabricated by thermal evaporation, which rely on high-cost and high energy-consumption vacuum equipment, raising significant concerns for mass production. This study develops a method for fabricating silver electrodes using the screen-printing process, aiming to achieve solar cell production through an all-solution coating process. By selecting appropriate blocking-layer materials and optimizing the process, we have achieved device efficiencies for organic photovoltaics (OPVs) with screen-printed silver electrodes comparable to those with silver electrodes fabricated by thermal evaporation. Furthermore, we developed a method to cure the silver ink using near-infrared (NIR) annealing, significantly reducing the curing time from 30 min with hot air annealing to just 5 s. Additionally, by employing sheet-to-sheet (S2S) slot-die coating, we scaled up the device area and completed module development, successfully verifying stability in ambient air. We have also extended the application of screen-printed silver electrodes to perovskite solar cells (PSCs). Full article

In fabricating functional layers, including thin-film transistors and conductive electrodes, using roll-to-roll (R2R) processing on polymer-based PET film, the instability of the slot-die coating meniscus under a high-speed web impedes functional layer formation with the desired thickness and width. The thickness profiles of the functional layers significantly impact the performance of the final products. In this study, we introduce an electrohydrodynamic (EHD)-based voltage application module to a slot-die coater to ensure the uniformity of the cross-machine direction (CMD) thickness profile within the functional layer and enable a stable, high-speed R2R process. The module can effectively control the spreadability of the meniscus by utilizing variations in the surface tension of the ink. The effectiveness of the EHD module was experimentally verified by applying a high voltage to a slot-die coater while keeping other process variables constant. As the applied voltage increases, the CMD thickness deviation reduces by 64.5%, and the production rate significantly increases (up to 300%), owing to the formation of a stable coated layer. The introduction of the EHD-based application module to the slot-die coater effectively controlled the spreadability of the meniscus, producing large-area functional layers. Full article

The mixing process is the basis of the electrode microstructure, which defines key cell performance indicators. This work investigated the effects of varying the energy input within the mixing procedure on slurry rheology, coating behavior, mechanical and electrical properties of dry electrodes and electrochemical performance of cells fabricated from these negative electrodes. Energy input differences were achieved by varying the solids content within the mixing procedure; however, the final total solids content of the slurries was always the same. The slurries, produced with graphite and silicon oxide as active materials and carboxymethylcellulose (CMC) and styrene-butadiene rubber as binders, showed large differences in flow behavior which were explained by changes in CMC adsorption and mechanical degradation because of increasing energy input. Low shear viscosity and the degree of shear thinning decreased with increasing energy input, resulting in a narrower stability window for slot-die coating. The resistance between the electrode and current collector decreased as more CMC was adsorbed on the active material. Electrode adhesion drastically dropped at the highest energy input, presumably due to a change in SBR distribution. Despite these variations, all fabricated pouch cells demonstrated excellent electrochemical performance and a slight trend of increased charge capability was observed in cells prepared with higher energy input. Full article

In die-sinking electrical discharge machining (EDM), it is challenging to implement internal flushing, mainly because it is easy to produce residual material columns on the workpiece cavity’s bottom surface, affecting the processing quality and efficiency. In order to solve this problem, the internal flushing slotted electrode EDM technology was proposed. The slotted electrode was designed, and its preparation method was described. The influence of pulse width, pulse interval, and flushing pressure on the performance of the internal flushing slotted electrode EDM was studied using single-factor experiments. The experimental results indicate that, with the increase in pulse width, the material removal rate (MRR) increases first and then decreases, while the electrode wear rate (EWR) and the relative electrode wear rate (REWR) decrease gradually; with the increase in pulse interval, the MRR decreases, while the EWR and the REWR increase gradually; with the increase in flushing pressure, the MRR increases first and then decreases, while the EWR and the REWR increase gradually. When the slotted electrode is used for continuous internal flushing EDM, the appropriate pulse width, flushing pressure, and smaller pulse interval can improve the MRR and reduce the EWR and the REWR. Full article

Wireless passive neural recording systems integrate sensory electrophysiological interfaces with a backscattering-based telemetry system. Despite the circuit simplicity and miniaturization with this topology, the high electrode–tissue impedance creates a major barrier to achieving high signal sensitivity and low telemetry power. In this paper, buffered impedance is utilized to address this limitation. The resulting passive telemetry-based wireless neural recording is implemented with thin flexible packages. Thus, the paper reports neural recording implants and integrator systems with three improved features: (1) passive high impedance matching with a simple buffer circuit, (2) a bypass capacitor to route the high frequency and improve mixer performance, and (3) system packaging with an integrated, flexible, biocompatible patch to capture the neural signal. The patch consists of a U-slot dual-band patch antenna that receives the transmitted power from the interrogator and backscatters the modulated carrier power at a different frequency. When the incoming power was 5–10 dBm, the neurosensor could communicate with the interrogator at a maximum distance of 5 cm. A biosignal as low as 80 µV peak was detected at the receiver. Full article

Dye-sensitized solar cells (DSSCs) are a very promising solution as remote sustainable low power sources for portable electronics and Internet of Things (IoT) applications due to their room-temperature and low-cost fabrication, as well as their high efficiency under artificial light. In addition, new achievements in developing semitransparent devices are driving interest in their implementation in the building sector. However, the main obstacle towards the large-scale exploitation of DSSCs mainly concerns their limited long-term stability triggered by the use of liquid electrolytes. Moreover, the device processing generally involves using a thick adhesive separator layer and vacuum filling or injection of the liquid polymer electrolyte between the two electrodes, a method that is difficult to scale up. This review summarizes the advances made in the design of alternative (quasi-)solid polymer electrolytes, with a focus on polysiloxane-based poly(ionic liquid)s. Their behavior in full DSSCs is presented and compared in terms of power generation maximization, advantages and shortcomings of the different device assembly strategies, as well as polymer electrolyte-related processing limitations. Finally, a fair part of the manuscript is allocated to the assessment of liquid and gel polymer electrolyte printability, particularly focusing on polysiloxane-based electrolytes. Spray, blade (slot-dye), screen and inkjet printing technologies are envisaged considering the polymer electrolyte thermophysical and rheological properties, as well as DSSC processing and operating conditions. Full article

The paper presents the study results of the parameters influence of arc welding with a consumable electrode with two-jet gas shielding in CO₂ on the structure and microhardness of high-strength steel 45 welded joints with slotted edges. Controlling the dynamic impact of the internal shielding gas jet on the processes in the welding zone changes the heat and mass transfer processes in the welding zone and results in the intensive mixing of the molten electrode metal with the base metal in the weld pool. The results of the studies determined the dynamic effect of the active shielding gas jet on the structure and microhardness of multilayered steel 45 welded joints with slotted edges using the method of full factorial experiment, developed dependences of chemical elements (carbon, silicon, manganese) content in the weld metal of multilayered steel 45 welded joints on the controlled parameters of the welding mode (Q, Iw, U). Due to uneven heat introduction into each of the welded plates during edge slotting, the asymmetric distribution of microhardness in the cross sections of welded joints relative to the weld axis indicates some differences in the structure and properties of the heat-affected zone (HAZ) and the weld. According to the results of the studies, consumable electrode arc welding with two-jet gas shielding provides faster distribution and equalization of heat on the product surface and reduces its instantaneous overheating, which improves the structural phase state of the welded joint made of steel 45 and reduces the microhardness gradient in the HAZ. An increase in the heat input of welding (a simultaneous increase in the welding current and voltage of the welding arc) leads to a decrease and smoothing of the microhardness peak in the HAZ. Full article

Energy shortage has become a global issue in the twenty-firt century, as energy consumption grows at an alarming rate as the fossil fuel supply exhausts. Perovskite solar cells (PSCs) are a promising photovoltaic technology that has grown quickly in recent years. Its power conversion efficiency (PCE) is comparable to that of traditional silicon-based solar cells, and scale-up costs can be substantially reduced due to its utilization of solution-processable fabrication. Nevertheless, most PSCs research uses hazardous solvents, such as dimethylformamide (DMF) and chlorobenzene (CB), which are not suitable for large-scale ambient operations and industrial production. In this study, we have successfully deposited all of the layers of PSCs, except the top metal electrode, under ambient conditions using a slot-die coating process and nontoxic solvents. The fully slot-die coated PSCs exhibited PCEs of 13.86% and 13.54% in a single device (0.09 cm²) and mini-module (0.75 cm²), respectively. Full article

Electrochromic (EC) windows on glass for thermal and glare protection in buildings, often referred to as smart (dimmable) windows, are commercially available, along with rearview mirrors or windows in aircraft cabins. Plastic-based applications, such as ski goggles, visors and car windows, that require lightweight, three-dimensional (3D) geometry and high-throughput manufacturing are still under development. To produce such EC devices (ECDs), a flexible EC film could be integrated into a back injection molding process, where the films are processed into compact 3D geometries in a single automized step at a low processing time. Polycarbonate (PC) as a substrate is a lightweight and robust alternative to glass due to its outstanding optical and mechanical properties. In this study, an EC film on a PC substrate was fabricated and characterized for the first time. To achieve a highly transmissive and colorless bright state, poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) was used as the working electrode, while titanium dioxide (TiO₂) was used as the counter electrode material. They were deposited onto ITO-coated PC films using dip- and slot-die coating, respectively. The electrodes were optically and electrochemically characterized. An ECD with a polyurethane containing gel electrolyte was investigated with regard to optical properties, switching speed and cycling behavior. The ECD exhibits a color-neutral and highly transmissive bright state with a visible light transmittance of 74% and a bluish-colored state of 64%, a fast switching speed (7 s/4 s for bleaching/coloring) and a moderately stable cycling behavior over 500 cycles with a decrease in transmittance change from 10%to 7%. Full article

Perovskites have already shown potential as active layers in photovoltaic applications. Furthermore, a low-cost and simple solution processing technology allows perovskites to be used in flexible and printed electronics. Perovskite solar cells (PSC) with a back-contact (BC) structure, in which the electrode system is based on a quasi-interdigitated back-contact (QIBC) design, promise to increase the power conversion efficiency (PCE) of devices beyond those that can be obtained using PSCs with a traditional sandwich structure. While the spin-coating technique is used to deposit the perovskite layer of lab-scale BC PSCs, the application of large-area printing techniques to deposit the perovskite layer of such devices is yet to be explored. Therefore, this work demonstrates an application of the slot-die coating technique to print the perovskite active layer of BC PSCs with QIBC electrodes on flexible polymer substrates. The morphology of the obtained perovskite films on QIBC electrodes are investigated and the primary photoelectric parameters of the resulting BC PSCs are measured. The charge carrier recombination processes in the fabricated BC PSCs are investigated and the dominant mechanism for carrier loss in the devices is determined. The findings of the work give an insight into the properties of the slot-die-coated perovskite active layer of BC PSCs and points to exciting new research opportunities in this direction. Full article

The connection of macrosystems with microsystems for in-line measurements is important in different biotechnological processes as it enables precise and accurate monitoring of process parameters at a small scale, which can provide valuable insights into the process, and ultimately lead to improved process control and optimization. Additionally, it allows continuous monitoring without the need for manual sampling and analysis, leading to more efficient and cost-effective production. In this paper, a 3D printed microfluidic (MF) chip for glucose (Glc) sensing in a liquid analyte is proposed. The chip made in Poly(methyl methacrylate) (PMMA) contains integrated serpentine-based micromixers realized via stereolithography with a slot for USB-like integration of commercial DropSens electrodes. After adjusting the sample’s pH in the first micromixer, small volumes of the sample and enzyme are mixed in the second micromixer and lead to a sensing chamber where the Glc concentration is measured via chronoamperometry. The sensing potential was examined for Glc concentrations in acetate buffer in the range of 0.1–100 mg/mL and afterward tested for Glc sensing in a cell culturing medium. The proposed chip showed great potential for connection with macrosystems, such as bioreactors, for direct in-line monitoring of a quality parameter in a liquid sample. Full article