Search Results (42)

As the planet most similar to Earth in the solar system, Mars holds an important role in exploring significant scientific problems, such as the evolution of the solar system and the origins of life. Research on Mars mainly rely on planetary remote sensing technology, among which thermal infrared remote sensing is of great studying significance. This technology enables the recording of Martian thermal radiation properties. However, the current spatial resolution of Mars thermal infrared remote sensing images remains relatively low, limiting the detection of fine-scale thermal anomalies and the generation of higher-precision surface compositional maps. While updating extraterrestrial exploration satellites can help enhancing the spatial resolution of thermal infrared images, this method entails high cost and long update cycles, making improvement difficult to conduct in the short term. To address this issue, this paper proposes a super-resolution reconstruction method for Mars thermal infrared remote sensing images integrating multi-source data. First, based on the principle of domain adaptation, we introduced a method using highly correlated visible light images as auxiliary to enhance the spatial resolution of thermal infrared images. Then, a multi-sources data integration method is designed to constrain the thermal radiation flux of resulting images, ensuring the radiation distribution remains consistent with the original low-resolution thermal infrared images. Through both subjective and objective evaluations, our method is demonstrated to significantly enhance the spatial resolution of existing Mars thermal infrared images. It optimizes the quality of existing data, increasing the resolution of the original thermal infrared images by four times. In doing so, it not only recovers finer texture details to produce better visual effects than typical super-resolution methods, but also maintains the consistency of thermal radiation flux, with the error after applying the consistency constraint reduced by nearly tenfold, ensuring the applicability of the results for scientific research. Full article

The ice surface temperature (IST) derived from thermal infrared remote sensing is crucial for accurately monitoring ice or snow surface temperatures in the polar region. Generally, the remote sensing IST needs to be validated by the in situ IST to ensure its accuracy. However, due to the limited availability of in situ IST measurements, previous studies in the validation of remote sensing ISTs are scarce in the Antarctic ice sheet. This study utilizes ISTs from eight broadband radiation stations to assess the accuracy of the latest-released Moderate Resolution Imaging Spectroradiometer (MODIS) IST and Visible Infrared Imager Radiometer Suite (VIIRS) IST products, which were derived from two different algorithms, the Split-Window (SW-based) algorithm and the Temperature–Emissivity Separation (TES-based) algorithm, respectively. This study also explores the sources of uncertainty in the validation process. The results reveal prominent errors when directly validating remote sensing ISTs with the in situ ISTs, which can be attributed to incorrect cloud detection due to the similar spectral characteristics of cloud and snow. Hence, cloud pixels are misclassified as clear pixels in the satellite cloud mask during IST validation, which emphasizes the severe cloud contamination of remote sensing IST products. By using a cloud index (n) to remove the cloud contamination pixels in the remote sensing IST products, the overall uncertainties for the four products are about 2 to 3 K, with the maximum uncertainty (RMSE) reduced by 3.51 K and the bias decreased by 1.26 K. Furthermore, a progressive cold bias in the validation process was observed with decreasing temperature, likely due to atmospheric radiation between the radiometer and the snow surface being neglected in previous studies. Lastly, this study found that the cloud mask errors of satellites are more pronounced during the winter compared to that in summer, highlighting the need for caution when directly using remote sensing IST products, particularly during the polar night. Full article

The global, near-real-time monitoring of volcano thermal activity has become feasible through thermal infrared sensors on various satellite platforms, which enable accurate estimations of volcanic emissions. Specifically, these sensors facilitate reliable estimation of Volcanic Radiative Power (VRP), representing the heat radiated during volcanic activity. A critical factor influencing VRP estimates is the identification of hotspots in satellite imagery, typically based on intensity. Different satellite sensors employ unique algorithms due to their distinct characteristics. Integrating data from multiple satellite sources, each with different spatial and spectral resolutions, offers a more comprehensive analysis than using individual data sources alone. We introduce an innovative Remote Sensing Data Fusion (RSDF) algorithm, developed within a Cloud Computing environment that provides scalable, on-demand computing resources and services via the internet, to monitor VRP locally using data from various multispectral satellite sensors: the polar-orbiting Moderate Resolution Imaging Spectroradiometer (MODIS), the Sea and Land Surface Temperature Radiometer (SLSTR), and the Visible Infrared Imaging Radiometer Suite (VIIRS), along with the geostationary Spinning Enhanced Visible and InfraRed Imager (SEVIRI). We describe and demonstrate the operation of this algorithm through the analysis of recent eruptive activities at the Etna and Stromboli volcanoes. The RSDF algorithm, leveraging both spatial and intensity features, demonstrates heightened sensitivity in detecting high-temperature volcanic features, thereby improving VRP monitoring compared to conventional pre-processed products available online. The overall accuracy increased significantly, with the omission rate dropping from 75.5% to 3.7% and the false detection rate decreasing from 11.0% to 4.3%. The proposed multi-sensor approach markedly enhances the ability to monitor and analyze volcanic activity. Full article

Ultra-low Earth orbit (LEO) satellites are widely used in the military, remote sensing, scientific research, and other fields. The ultra-LEO satellite faces the harsh aerothermal environment, and the complex variable attitude task requires the radiator of the satellite to not only meet the heat dissipation requirements of the load but also to resist aerothermal flux. In this study, the aerothermal flux of 160–110 km was calculated, and the loop heat pipe (LHP) coupled with a thermo-electric cooler (TEC) and multi-layer insulation (MLI) were applied to ultra-LEO satellites to determine the variable switching and fast response of heat dissipation and heat protection. An aerothermal flux simulation test platform was built. After the assessment of the ultra-LEO aerothermal flux test, even when the head temperature was as high as 350 °C and the side radiator temperature was as high as 160 °C, the temperature of the internal heat source could be controlled within 22.5 °C through the efficient work of the thermal variable switch system. The study confirms the accuracy and feasibility of the system, which provides an important reference for the subsequent actual on-orbit mission. Full article

Surface longwave radiation (SLR) plays a pivotal role in the Earth’s energy balance, influencing a range of environmental processes and climate dynamics. As the demand for high spatial resolution remote sensing products grows, there is an increasing need for accurate SLR retrieval with enhanced spatial detail. This study focuses on the development and validation of models to estimate SLR using measurements from the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) sensor. Given the limitations posed by fewer spectral bands and data products in ASTER compared to moderate-resolution sensors, the proposed approach combines an atmospheric radiative transfer model MODerate resolution atmospheric TRANsmission (MODTRAN) with the Light Gradient Boosting Machine algorithm to estimate SLR. The MODTRAN simulations were performed to construct a representative training dataset based on comprehensive global atmospheric profiles and surface emissivity spectra data. Global sensitivity analyses reveal that key inputs influencing the accuracy of SLR retrievals should reflect surface thermal radiative signals and near-surface atmospheric conditions. Validated against ground-based measurements, surface upward longwave radiation (SULR) and surface downward longwave radiation (SDLR) using ASTER thermal infrared bands and surface elevation estimations resulted in root mean square errors of 17.76 W/m² and 25.36 W/m², with biases of 3.42 W/m² and 3.92 W/m², respectively. Retrievals show systematic biases related to extreme temperature and moisture conditions, e.g., causing overestimation of SULR in hot humid conditions and underestimation of SDLR in arid conditions. While challenges persist, particularly in addressing atmospheric variables and cloud masking, this work lays a foundation for accurate SLR retrieval from high spatial resolution sensors like ASTER. The potential applications extend to upcoming satellite missions, such as the Landsat Next, and contribute to advancing high-resolution remote sensing capabilities for an improved understanding of Earth’s energy dynamics. Full article

This study presents the spatio–temporal evolution of the electric and magnetic fields recorded by the China Seismo–Electromagnetic Satellite (CSES) and the thermal infrared remote sensing data observed by the Chinese stationary meteorological satellites Feng Yun–2G (FY–2G) associated with the 2021 Mw7.3 Maduo earthquake. Specifically, we analyzed the power spectrum density (PSD) data of the electric field in the extremely low frequency (ELF) band, the geomagnetic east–west vector data, and the temperature of brightness blackbody (TBB) data to investigate the spatio–temporal evolution characteristics under quiet space weather conditions (Dst > −30 nT and Kp < 3). Results showed that (1) the TBB radiation began to increase notably along the northern fault of the epicenter ~1.5 months prior to the occurrence of the earthquake. It achieved its maximum intensity on 17 May, and the earthquake occurred as the anomalies decreased. (2) The PSD in the 371 Hz–500 Hz and 700 Hz–871 Hz bands exhibited anomaly perturbations near the epicenter and its magnetic conjugate area on May 17, with particularly notable perturbations observed in the latter. The anomaly perturbations began to occur ~1 month before the earthquake, and the earthquake occurred as the anomalies decreased. (3) Both the magnetic –east–west component vector data and the ion velocity Vx data exhibited anomaly perturbations near the epicenter and the magnetic conjugate area on 11 May and 16 May. (4) The anomaly perturbations in the thermal infrared TBB data, CSES electric field, and magnetic field data all occurred within a consistent perturbation time period and spatial proximity. We also conducted an investigation into the timing, location, and potential causes of the anomaly perturbations using the Vx ion velocity data with magnetic field –east–west component vector data, as well as the horizontal –north–south and vertical component PSD data of the electric field with the magnetic field –east–west component vector data. There may be both chemical and electromagnetic wave propagation models for the “lithosphere—atmosphere—ionosphere” coupling (LAIC) mechanism of the Maduo earthquake. Full article

Land surface temperature (LST) is a fundamental parameter in global climate, environmental, and geophysical studies. Remote sensing is an essential approach for obtaining large-scale and frequently updated LST data. However, due to the wide field of view of remote sensing sensors, the observed LST with diverse view geometries suffers from inconsistency caused by the thermal radiation directionality (TRD) effect, which results in LST products being incomparable, especially during daytime. To address this issue and correct current off-nadir LSTs to nadir LSTs, a semi-physical time-evolved kernel-driven model (TEKDM) is proposed, which depicts multitemporal TRD patterns during the daytime. In addition, we employ a Bayesian optimization method to calibrate seven unknown parameters in the TEKDM. Validation results using the U.S. Climate Reference Network (USCRN) sites show that the RMSE (MBE) for GOES-16 and MODIS off-nadir LST products is reduced from 3.29 K (−2.0 K) to 2.34 K (−0.02 K), with an RMSE reduction of 0.95 K (29%) and a significant reduction in systematic bias. Moreover, the proposed method successfully eliminates the angular and temporal dependence of the LST difference between the satellite off-nadir LST and in situ nadir LST. In summary, this study presents a feasible approach for estimating the high-accuracy nadir LST, which can enhance the applicability of LST products in various domains. Full article

Land Surface Temperature (LST) products obtained by thermal infrared (TIR) remote sensing contain considerable blank areas due to the frequent occurrence of cloud coverage. The studies on the all-time reconstruction of the cloud-covered LST of geostationary meteorological satellite LST products are relatively few. To accurately fill the blank area, a hybrid method for reconstructing hourly FY-4A AGRI LST under cloud-covered conditions was proposed using a random forest (RF) regression algorithm and Savitzky-Golay (S-G) filtering. The ERA5-Land surface cumulative net radiation flux (SNR) reanalysis data was first introduced to represent the change in surface energy arising from cloud coverage. The RF regression method was used to estimate the LST correlation model based on clear-sky LST and the corresponding predictor variables, including the normalized difference vegetation index (NDVI), the normalized difference water index (NDWI), surface elevation and slope. The fitted model was then applied to reconstruct the cloud-covered LST. The S–G filtering method was used to smooth the outliers of reconstructed LST in the temporal dimension. The accuracy evaluation was performed using the measured LST of the representative meteorological stations after scale correction. The coefficients of determination derived with the reference LST were all above 0.73 on the three examined days, with a bias of −1.13–0.39 K, mean absolute errors (MAE) of 1.46–2.4 K, and root mean square errors (RMSE) of 1.77–3.2 K. These results indicate that the proposed method has strong potential for accurately restoring the spatial and temporal continuity of LST and can provide a solution for the production and research of gap-free LST products with high temporal resolution. Full article

Lakes on the Qinghai Tibet Plateau (QTP) are widely distributed spatially, and they are mostly seasonally frozen. Due to global warming, the thickness and phenology of the lake ice has been changing, which profoundly affects the regional climate evolution. There are a few studies about lake ice in alpine regions, but the understanding of climatological characteristics of lake ice on the QTP is still limited. Based on a field experiment in the winter of 2022, the thermal conductivity of Qinghai Lake ice was determined as 1.64 W·m⁻¹·°C⁻¹. Airborne radar ice thickness data, meteorological observations, and remote sensing images were used to evaluate a quasi-steady ice model (Leppäranta model) performance of the lake. This is an analytic model of lake ice thickness and phenology. The long-term (1979–2017) ice history of the lake was simulated. The results showed that the modeled mean ice thickness was 0.35 m with a trend of −0.002 m·a⁻¹, and the average freeze-up start (FUS) and break-up end (BUE) were 30 December and 5 April, respectively, which are close to the field and satellite observations. The simulated trend of the maximum ice thickness from 1979 to 2017 (0.004 m·a⁻¹) was slightly higher than the observed result (0.003 m·a⁻¹). The simulated trend was 0.20 d·a⁻¹ for the FUS, −0.34 d·a⁻¹ for the BUE, and −0.54 d·a⁻¹ for the ice duration (ID). Correlation and detrending analysis were adopted for the contribution of meteorological factors. In the winters of 1979–2017, downward longwave radiation and air temperature were the two main factors that had the best correlation with lake ice thickness. In a detrending analysis, air temperature, downward longwave radiation, and solar radiation contributed the most to the average thickness variability, with contributions of 42%, 49%, and −48%, respectively, and to the maximum thickness variability, with contributions of 41%, 45%, and −48%, respectively. If the six meteorological factors (air temperature, downward longwave radiation, solar radiation, wind speed, pressure, and specific humidity) are detrending, ice thickness variability will increase 83% on average and 87% at maximum. Specific humidity, wind, and air pressure had a poor correlation with ice thickness. The findings in this study give insights into the long-term evolutionary trajectory of Qinghai Lake ice cover and serve as a point of reference for investigating other lakes in the QTP during cold seasons. Full article

Satellite laser altimetry technology, a novel space remote sensing technique, actively acquires high-precision elevation information about the Earth’s surface. However, the accuracy of laser altimetry can be compromised by alterations in the satellite-ground environment, thermal dynamics, and cosmic radiation. These factors may induce subtle variations in the installation and internal structure of the spaceborne laser altimeter on the satellite platform, diminishing measurement precision. In-orbit calibration is thus essential to enhancing the precision of laser altimetry. Through collaborative calculations between satellite and ground stations, we can derive correction parameters for laser pointing and ranging, substantially improving the accuracy of satellite laser altimetry. This paper introduces a sophisticated calibration method for laser altimeter pointing and ranging that utilizes dense control points. The approach interpolates discrete ground control point data into continuous simulated terrain using empirical Bayesian kriging, subsequently categorizing the data for either pointing or ranging calibration according to their respective functions. Following this, a series of calibration experiments are conducted, prioritizing “pointing” followed by “ranging” and continuing until the variation in the ranging calibration results falls below a predefined threshold. We employed experimental data from ground control points (GCPs) in Xinjiang and Inner Mongolia, China, to calibrate the GaoFen-7 (GF-7) satellite Beam 2 laser altimeter as per the outlined method. The calibration outcomes were then benchmarked against those gleaned from infrared laser detector calibration, revealing disparities of 1.12 s in the pointing angle and 2 cm in the ranging correction value. Post validation with ground control points, the measurement accuracy was refined to 0.15 m. The experiments confirm that the proposed calibration method offers accuracy comparable to that of infrared laser detector calibration and can facilitate the updating of 1:10,000 topographic maps utilizing stereo optical imagery. Furthermore, this method is more cost-effective and demands fewer personnel for ground control point collection, enhancing resource efficiency compared to traditional infrared laser detector calibration. The proposed approach surpasses terrain-matching limitations when calibrating laser ranging parameters and presents a viable solution for achieving frequent and high-precision in-orbit calibration of laser altimetry satellites. Full article

It is of great significance to study the thermal radiation anomalies of earthquake swarms in the same area in terms of selecting abnormal characteristic determination parameters, optimizing and determining the processing model, and understanding the abnormal machine. In this paper, we investigated short-term and long-term thermal radiation anomalies induced by earthquake swarms in Iran and Pakistan between 2007 and 2016. The anomalies were extracted from infrared remote sensing black body temperature data from the China Geostationary Meteorological Satellites (FY-2C/2E/2F/2G) using the multiscale time-frequency relative power spectrum (MS T-FRPS) method. By analyzing and summarizing the thermal radiation anomalies of series earthquake groups with consistency law through a stable and reliable MS T-FRPS method, we first obtained the relationship between anomalies and ShakeMaps from USGS and proposed the anomaly regional indicator (ARI) to determine seismic anomalies and the magnitude decision factor (MDF) to determine seismic magnitude. In addition, we explored the following discussions: earthquake impact on regional thermal radiation background and the relationship between thermal anomalies and earthquake magnitude and the like. Future research directions using the MS T-FRPS method to characterize regional thermal radiation anomalies induced by strong earthquakes could help improve the accuracy of earthquake magnitude determination. Full article

Following the launch of the ZY1-02E satellite, the thermal infrared sensor aboard the satellite experienced alterations in the space environment, leading to varying degrees of attenuation in some components. The laboratory calibration accuracy could not satisfy the demands of quantitative production, and a certain degree of deviation was observed in on-orbit calibration. To accurately characterize the on-orbit radiation properties of thermal infrared remote sensing payloads, an absolute radiometric calibration campaign was carried out at the Ulansuhai Nur and Baotou calibration sites in Inner Mongolia in July 2022. This paper outlines the processes of onboard calibration and vicarious calibration for the ZY1-02E satellite, comparing the outcomes of onboard calibration with those of vicarious calibration. The onboard calibration method involved internal calibration, while the vicarious calibration method utilized an on-orbit absolute radiometric calibration technique based on various natural features that were not constrained by satellite–Earth spectrum matching requirements. Calibration coefficients were acquired, and the absolute radiometric calibration results of on-orbit vicarious and onboard calibration were compared, analyzed, and verified using the radiance computed from measured data and the reference sensor data. The accuracy of on-orbit absolute vicarious calibration was determined, and the causes for the decline in the radiation calibration accuracy on the orbiting satellite were examined. The findings revealed that the vicarious calibration results exhibited a lower percentage of radiance deviation compared with the onboard calibration results, meeting the quantitative requirements of remote sensing data. These results were significantly better than those obtained from onboard blackbody calibration, offering a data foundation for devising satellite calibration plans and enhancing calibration algorithms. In the future, the developmental trend of on-orbit radiometric calibration technology will encompass high-precision and slow-attenuation onboard calibration techniques, as well as high-frequency and simplified-step vicarious calibration methods. Full article

Georeferencing accuracy plays a crucial role in providing high-quality ready-to-use remote sensing data. The georeferencing of nighttime thermal satellite imagery conducted by matching to a basemap is challenging due to the complexity of thermal radiation patterns in the diurnal cycle and the coarse resolution of thermal sensors in comparison to sensors used for imaging in the visual spectral range (which is typically used for creating basemaps). The presented paper introduces a novel approach for the improvement of the georeferencing of nighttime thermal ECOSTRESS imagery: an up-to-date reference is created for each to-be-georeferenced image, derived from land cover classification products. In the proposed method, edges of water bodies are used as matching objects, since water bodies exhibit a relatively high contrast with adjacent areas in nighttime thermal infrared imagery. The method was tested on imagery of the East African Rift and validated using manually set ground control check points. The results show that the proposed method improves the existing georeferencing of the tested ECOSTRESS images by 12.0 pixels on average. The strongest source of uncertainty for the proposed method is the accuracy of cloud masks because cloud edges can be mistaken for water body edges and included in fitting transformation parameters. The georeferencing improvement method is based on the physical properties of radiation for land masses and water bodies, which makes it potentially globally applicable, and is feasible to use with nighttime thermal infrared data from different sensors. Full article

Atmospheric ozone plays an important role in the biosphere’s absorbing of dangerous solar UV radiation and its contributions to the Earth’s climate. Nowadays, ozone variations are widely monitored by different local and remote sensing methods. Satellite methods can provide data on the global distribution of ozone and its anomalies. In contrast to measurement techniques based on solar radiation measurements, Fourier-transform infrared (FTIR) satellite measurements of thermal radiation provide information, regardless of solar illumination. The global distribution of total ozone columns (TOCs) measured by the IKFS-2 spectrometer aboard the “Meteor M N2” satellite for the period of 2015 to 2020 is presented. The retrieval algorithm uses the artificial neural network (ANN) based on measurements of TOCs by the Aura OMI instrument and the method of principal components for representing IKFS-2 spectral measurements. Latitudinal and seasonal dependencies on the ANN training errors are analyzed and considered as a first approximation of the TOC measurement errors. The TOCs derived by the IKFS-2 instrument are compared to independent ground-based and satellite data. The average differences between the IKFS-2 data and the independent TOC measurements are up to 2% (IKFS-2 usually slightly underestimates the other data), and the standard deviations of differences (SDDs) vary from 2 to 4%. At the same time, both the analysis of the ANN approximation errors of the OMI data and the comparison of the IKFS-2 results with independent data demonstrate an increase in discrepancies towards the poles. In the spring–winter period, SDDs reach 8% in the Southern and 6% in the Northern Hemisphere. The technique presented can be used to process the IKFS-2 spectral data, and as a result, it can provide global information on the TOCs in the period of 2015–2020, regardless of the solar illumination and the presence of clouds. Full article

On 2 January 2022, an earthquake of M_s 5.5 occurred in Ninglang County, Lijiang City, the earthquake-prone area of northwestern Yunnan. Whether this earthquake caused significant deformation and thermal anomalies and whether there is a relationship between them needs further investigation. Currently, multi-source remote sensing technology has become a powerful tool for long-time-series monitoring of earthquakes and active ruptures which mainly focuses on single crustal deformation and thermal anomaly. This study aims to reveal the crustal deformation and thermal anomaly characteristics of the Ninglang earthquake by using both Interferometric Synthetic Aperture Radar (InSAR) and Robust Satellite Techniques (RST). First, Sentinel-1A satellite SAR data were selected to obtain the coseismic deformation field based on Differential InSAR (D-InSAR), and the Small Baseline Set InSAR (SBAS-InSAR) technique was exploited to invert the pre- and post-earthquake displacement sequences. Then, RST was used to extract the thermal anomalies before and after the earthquake by using Moderate Resolution Imaging Spectroradiometer Land Surface Temperature (MODIS LST). The results indicate that the seismic crustal deformation is dominated by subsidence, with 23 thermal anomalies before and after the earthquake. It is speculated that the Yongning Fault in the deformation area is the main seismogenic fault of the Ninglang earthquake, which is dominated by positive fault dip-slip motion. Meanwhile, the seismic fault system composed of NE- and NW-oriented faults is an important factor in the formation of thermal anomalies, which are accompanied by changes in stress at different stages before and after the earthquake. Moreover, the crustal deformation and seismic thermal anomalies are correlated in time and space, and the active rupture activities in the region produce deformation accompanied by changes in thermal radiation. This study provides clues from remote sensing observations for analyzing the Ninglang earthquake and provides a reference for the joint application of InSAR and RST for earthquake monitoring. Full article