Search Results (59)

Ion-exchange membranes (IEMs) are widely used in reverse-electrodialysis (RED) technology, which can collect the salinity gradient energy between concentrated and diluted solutions and convert it into electromotive force (EMF) to drive power generation and hydrogen production. Recent studies have indicated that the permselectivity of IEMs is vital to determining the performance of an RED stack. In this study, the influences of solution concentration, ion species, and solution temperature on the permselectivity of IEMs were experimentally investigated. The results demonstrate that the permselectivity of IEMs decreases with increasing concentrations of KAc, LiCl, and LiBr solutions for both concentrated solutions (3–5 M) and dilute solutions (0.02–0.2 M). Further, through comparing the LiBr and KBr solutions as well as the LiCl, KCl, and NH₄Cl solutions, respectively, K⁺ demonstrates a higher permselectivity than Li⁺, and both of which are smaller than NH₄⁺ under the same cation and concentration conditions. Moreover, another test was conducted using three potassium salt solutions with different anions, and the experimental permselectivity order is Ac⁻ > Br⁻ > Cl⁻. A slight increase in solution temperature enhances the permselectivity of IEMs due to the increase in ionic mobility. However, an excessive temperature is detrimental to membrane stability and thus reduces permselectivity. It can be seen that ions with low hydration energy, a small hydration radius, and high mobility show a higher permselectivity. Full article

The feasibility of an analogous reverse electrodialysis (RED) process for power generation and acid recovery from acidic waste streams in the steel industry is investigated in this study. A comprehensive model was established to simulate the transport phenomena and power generation, which was validated through experimental data. The simulated operation time was 3 h, during which an acid recovery rate of 41.7% was achieved, and the maximum output power density reached 30.37 μW·cm⁻². The results demonstrated a strong dependence of output power density on the acid concentration, with a linear relationship within the tested range of 1.0–3.0 mol·L⁻¹ HCl. An optimal flow rate range was identified that maximized power output, with the best value of 90 mL∙min⁻¹. The differences in energy harvesting between the traditional acid diffusion dialysis process and our analogous RED process were demonstrated via simulation. The importance of system electroneutrality in driving ion migration and forming ionic currents was crucial for effective power generation. The analogous RED process is a promising solution for efficient acid recovery and power generation from industrial acid waste, offering a sustainable treatment approach. Full article

Sustainable development is linked to the achievement of several different objectives, as outlined by the 17 Sustainable Development Goals (SDGs) defined by the United Nations. Among them are the production of clean water and the combat of climate change, which is strictly linked to the use of fossil fuels as a primary energy source and their related CO₂ emissions. Water and energy are strongly interconnected. For instance, when processing water, energy is needed to pump, treat, heat/cool, and deliver water. Membrane operations for water treatment/desalination contribute to the recovery of purified/fresh water and reducing the environmental impact of waste streams. However, to be sustainable, water recovery must not be energy intensive. In this respect, this contribution aims to illustrate the state of the art and perspectives in desalination by reverse osmosis (RO), discussing the various approaches looking to improve the energy efficiency of this process. In particular, the coupling of RO with other membrane operations, like pressure-retarded osmosis (PRO), reverse electrodialysis (RED), and forward osmosis (FO), as well as the osmotic-assisted reverse osmosis (OARO) system, are reported. Moreover, the possibility of coupling a membrane distillation (MD) unit to an RO one to increase the overall freshwater recovery factor and reduce the brine volumes that are disposed is also discussed. Specific emphasis is placed on the strategies being applied to reduce the MD thermal energy demand, so as to couple the production of the blue gold with the fight against climate change. Full article

Salinity gradient power (SGP) technologies, including pressure-retarded osmosis (PRO) and reverse electrodialysis (RED), have the potential to be utilized for the purpose of harvesting energy from the difference in salinity between two water streams. One challenge associated with SGP is a reduction in power density due to membrane fouling when impaired water is utilized as a low-salinity water stream. Accordingly, this study sought to explore the feasibility of membrane capacitive deionization (MCDI), a low-energy water treatment technique, as a novel pretreatment method for SGP. Laboratory-scale experiments were conducted to evaluate the impact of MCDI pretreatment on the performance of PRO and RED. The low-salinity water was obtained from a brackish water reverse osmosis (BWRO) plant, while the high-salinity water was a synthetic seawater desalination brine. The removal efficiency of organic and inorganic substances in brackish water reverse osmosis (BWRO) brine by MCDI was estimated, as well as theoretical energy consumption. The results demonstrated that MCDI attained removal efficiencies of up to 88.8% for organic substances and 78.8% for inorganic substances. This resulted in a notable enhancement in the lower density for both PRO and RED. The power density of PRO exhibited a notable enhancement, reaching 3.57 W/m² in comparison to 1.14 W/m² recorded for the BWRO brine. Conversely, the power density of RED increased from 1.47 W/m² to 2.05 W/m². Given that the energy consumption by MCDI is relatively low, it can be surmised that the MCDI pretreatment enhances the overall efficiency of both PRO and RED. However, to fully capitalize on the benefits of MCDI pretreatment, it is recommended that further process optimization be conducted. Full article

The absorption refrigeration system (ARS) stands as a remarkable device that is capable of efficiently harnessing low-grade thermal energy and converting it into cooling capacity. The reverse electrodialysis (RED) system harvests the salinity gradient energy embedded in two solutions of different concentrations into electricity. An innovative RED–ARS integration system is proposed that outputs cooling capacity and electric energy, driven by waste heat. In this study, a comprehensive mathematical simulation model of a RED–ARS integration system was established, and an aqueous lithium bromide solution was selected as the working solution. Based on this model, the authors simulated and analyzed the impact of various factors on system performance, including the heat source temperature (90 °C to 130 °C), concentrated solution concentration (3 mol∙L⁻¹ to 9 mol∙L⁻¹), dilute solution concentration (0.002 mol∙L⁻¹ to 0.5 mol∙L⁻¹), condensing temperature of the dilute solution (50 °C to 70 °C), solution temperature (30 °C to 60 °C) and flow rate (0.4 cm∙s⁻¹ to 1.3 cm∙s⁻¹) in the RED stacks, as well as the number of RED stacks. The findings revealed the maximum output power of 934 W, a coefficient of performance (COP) of 0.75, and overall energy efficiency of 33%. Full article

In response to the growing demand for potable water, this study presents a practical methodology for designing and fabricating a hybrid desalination system that integrates reverse electrodialysis and electrodialysis using 3D-printing technology. The hybrid system combines the energy generation potential of RED with the salt removal capabilities of ED, reducing energy consumption. Customized reactors were designed to enhance flow distribution and ion exchange, with computational fluid dynamics simulations validating the hydrodynamic performance. The reactors were fabricated using 3D printing, allowing rapid, cost-effective production, with functional reactors constructed in under 24 h. The system achieved a 15% reduction in salt concentration within one hour, with a specific energy consumption of 0.1388 Wh/m³ and a water recovery rate of 50%. These results demonstrate the functionality of the RED-ED hybrid system for achieving energy savings and performing water desalination. This methodology provides a scalable and replicable solution for water treatment applications, especially in regions with abundant salinity gradients and limited freshwater resources, while offering a multidisciplinary approach that integrates physicochemical and engineering principles for effective device development. Full article

The reverse electrodialysis heat engine (REDHE) represents a transformative innovation that converts low-grade thermal energy into salinity gradient energy (SGE). This crucial form of energy powers reverse electrodialysis (RED) reactors, significantly changing wastewater treatment paradigms. This comprehensive review explores the forefront of this emerging field, offering a critical synthesis of key discoveries and theoretical foundations. This review begins with a summary of various oxidation degradation methods, including cathodic and anodic degradation processes, that can be integrated with RED technology. The degradation principles and characteristics of different RED wastewater treatment systems are also discussed. Then, this review examines the impact of several key operational parameters, degradation circulation modes, and multi-stage series systems on wastewater degradation performance and energy conversion efficiency in RED reactors. The analysis highlights the economic feasibility of using SGE derived from low-grade heat to power RED technology for wastewater treatment, offering the dual benefits of waste heat recovery and effective wastewater processing. Full article

The shape of nanochannels plays a crucial role in the ion selectivity and overall performance of reverse electrodialysis (RED) systems. However, current research on two-dimensional nanochannel shapes is largely limited to a few fixed asymmetric forms. This study explores the impact of randomly shaped nanochannels using dimensionless methods, controlling their randomness by varying their length and shape amplitude. The research systematically compares how alterations in the nanochannel length and shape amplitude influence various system performance parameters. Our findings indicate that increasing the nanochannel length can significantly enhance the system performance. While drastic changes in the nanochannel shape amplitude positively affect the system performance, the most significant improvements arise from the interplay between the nanochannel length and shape amplitude. This compounding effect creates a local optimum, resulting in peak system performance. Within the range of dimensionless lengths from 0 to 30, the system reaches its optimal performance at a dimensionless length of approximately 25. Additionally, we explored two other influencing factors: the nanochannel surface charge density and the concentration gradient of the solution across the nanochannel. Optimal performance is observed when the nanochannel has a high surface charge density and a low concentration gradient, particularly with random shapes. This study advances the theoretical understanding of RED systems in two-dimensional nanochannels, guiding research towards practical operational conditions. Full article

Reverse electrodialysis (RED) is one of the methods able to generate energy from the salinity gradient between sea- and river water. The technique is based on the diffusion of ions through membranes that specifically allow either cations or anions to pass through. This ion current is converted into an external electric current at electrodes via suitable redox reactions. Seawater contains mainly eight different ions and the description of transport phenomena in membranes in classical terms of isolated species is not sufficient because the different particles have different velocities—in the same direction or opposite—in the same membrane. More realistic is the Maxwell–Stefan (MS) theory that takes all interactions between the different particles in account; however, such a model is complex and validation is difficult. Therefore, a simplified system is used with solely NaCl in solution, using only 9 diffusivities in the calculation. These values are estimated from the literature and are applied to an MS model of the RED process. Using experimental data of NaCl and water transport as well as power density, these diffusivities are adapted in the MS model. Reliable values for the diffusivities were obtained for the following three interactions: H₂O–Na⁺, H₂O–Cl⁻ and Na⁺–Cl⁻. Full article

Exploring the utilization of ion exchange membranes (IEMs) in salinity gradient energy harvesting, a technique that capitalizes on the salinity difference between seawater and freshwater to generate electricity, this study focuses on optimizing PVDF to Nafion ratios to create ultra-thin membranes. Specifically, our investigation aligns with applications such as reverse electrodialysis (RED), where IEMs facilitate selective ion transport across salinity gradients. We demonstrate that membranes with reduced Nafion content, particularly the 50:50 PVDF:Nafion blend, retain high permselectivity comparable to those with higher Nafion content. This challenges traditional understandings of membrane design, highlighting a balance between thinness and durability for energy efficiency. Voltage–current analyses reveal that, despite lower conductivity, the 50:50 blend shows superior short-circuit current density under salinity gradient conditions. This is attributed to effective ion diffusion facilitated by the blend’s unique microstructure. These findings suggest that blended membranes are not only cost-effective but also exhibit enhanced performance for energy harvesting, making them promising candidates for sustainable energy solutions. Furthermore, these findings will pave the way for advances in membrane technology, offering new insights into the design and application of ion exchange membranes in renewable energy. Full article

In this study, novel pore-filled anion-exchange membranes (PFAEMs) modified with polypyrrole (PPy) and reduced graphene oxide (rGO) were developed to improve the energy harvesting performance of reverse electrodialysis (RED). The surface-modified PFAEMs were fabricated by varying the contents of PPy and rGO through simple spin coating and chemical/thermal treatments. It was confirmed that the PPy and PPy/rGO layers introduced on the membrane surface did not significantly increase the electrical resistance of the membrane and could effectively control surface characteristics, such as structural tightness, hydrophilicity, and electrostatic repulsion. The PPy/rGO-modified PFAEM showed excellent monovalent ion selectivity, more than four times higher than that of the commercial membrane (AMX, Astom Corp., Tokyo, Japan). This means that the PPy/rGO layer can effectively reduce the permeation of multivalent ions with a high charge intensity and a relatively large hydration radius compared to monovalent ions. The results of evaluating the performance of the surface-modified PFAEMs by applying them to a RED cell revealed that the decrease in potential difference occurring in the membrane was reduced by effectively suppressing the uphill transport of multivalent ions. Consequently, the PPy/rGO-modified membrane exhibited a 5.43% higher power density than the AMX membrane. Full article

Reverse electrodialysis (RED), an emerging membrane-based technology, harnesses salinity gradient energy for sustainable power generation. Accurate characterization of electrical parameters in RED stacks is crucial to monitoring its performance and exploring possible applications. In this study, a DC electronic load module (DCELM) is implemented in a constant current condition (CC mode) for characterization of lab scale RED process, using a RED prototype in-house designed and manufactured (RU1), at different data capture setups (DCS), on which the total number of steps for data capture (NS) and the number of measurements per step (ρ) are the parameters that were modified to study their effect on obtained electrical parameters in RED. NS of 10, 50, and 100 and ρ of 10 and 20 were used with this purpose. The accuracy of resulting current and voltage steps can be enhanced by increasing NS and ρ values, and according to obtained results, the higher accuracy of resulting output current and voltage steps, with low uncertainty of the average output steps (AOS) inside the operational region of power curve, was obtained using a DCS of NS = 100 and ρ = 20. The developed DCELM is a low-cost alternative to commercial electronic load devices, and the proposed methodology in this study represents an adaptative and optimizable CC mode characterization of RED process. The results obtained in this study suggest that data capture conditions have a direct influence of RED performance, and the accuracy of electrical parameters can be improved by optimizing the DCS parameters, according to the required specifications and the scale of RED prototypes. Full article

The power conversion of salinity gradient energy (SGE) between concentrated brine from seawater desalination and seawater by reverse electrodialysis (RED) benefits energy conservation and also dilutes the discharge concentration to relieve the damage to coastal ecosystems. However, two key performance indexes of the maximum net power density and energy conversion efficiency for a RED stack harvesting the energy usually cannot reach the optimal simultaneously. Here, an optimization study on the two indexes was implemented to improve the performance of RED in harvesting the energy. A RED model for capturing the SGE between concentrated brine and seawater was constructed, and the correlation coefficients in the model were experimentally determined. Based on the model, the effects of a single variable (concentration, flow rate, temperature, thickness of the compartment, length of the electrode) on the performance of a RED stack are analyzed. The multi-objective optimization method based on the genetic algorithm was further introduced to obtain the optimal solution set, which could achieve the larger net power density and energy conversion efficiency with coordination. The ranges of optimal feed parameters and stack size were also obtained. The optimal flow velocity of the dilute solution and the concentration of the dilute solution are approximately 7.3 mm/s and 0.4 mol/kg, respectively. Full article

The chemical potential difference at the discharge points of coastal Wastewater Treatment Plants (WWTPs) uncovers the opportunity to harness renewable salinity gradient energy (SGE). This work performs an upscaling assessment of reverse electrodialysis (RED) for SGE harvesting of two selected WWTPs located in Europe, quantified in terms of net present value (NPV). For that purpose, a design tool based on an optimization model formulated as a Generalized Disjunctive Program previously developed by the research group has been applied. The industrial scale-up of SGE-RED has already proven to be technically and economically feasible in the Ierapetra medium-sized plant (Greece), mainly due to a greater volumetric flow and a warmer temperature. At the current price of electricity in Greece and the up-to-date market cost of membranes of 10 EUR/m², the NPV of an optimized RED plant in Ierapetra would amount to EUR117 thousand operating with 30 RUs in winter and EUR 157 thousand for 32 RUs in summer, harnessing 10.43 kW and 11.96 kW of SGE for the winter and summer seasons, respectively. However, in the Comillas facility (Spain), this could be cost-competitive with conventional alternatives, namely coal or nuclear power, under certain conditions such as lower capital expenses due to affordable membrane commercialization (4 EUR/m²). Bringing the membrane price down to 4 EUR/m² would place the SGE-RED’s Levelized Cost of Energy in the range of 83 EUR/MWh to 106 EUR/MWh, similar to renewable sources such as solar PV residential rooftops. Full article

Salinity gradient energy has gained attention in recent years as a renewable energy source, especially employing reverse electrodialysis technology (RED), which is based on the role of ion exchange membranes. In this context, many efforts have been developed by researchers from all over the world to advance the knowledge of this green source of energy. However, the influence of divalent ions on the performance of the technology has not been deeply studied. Basically, divalent ions are responsible for an increased membrane resistance and, therefore, for a decrease in voltage. This work focuses on the estimation of the resistance of the RED membrane working with water flows containing divalent ions, both theoretically by combining the one-thread model with the Donnan exclusion theory for the gel phase, as well as the experimental evaluation with Fumatech membranes FAS-50, FKS-50, FAS-PET-75, and FKS-PET-75. Furthermore, simulated results have been compared to data recently reported with different membranes. Besides, the influence of membrane resistance on the overall performance of reverse electrodialysis technology is evaluated to understand the impact of divalent ions in energy generation. Results reflect a minor effect of sulfate on the gross power in comparison to the effect of calcium and magnesium ions. Thus, this work takes a step forward in the knowledge of reverse electrodialysis technology and the extraction of salinity gradient energy by advancing the influence of divalent ions on energy recovery. Full article