Search Results (18)

Five series of rigid polyurethane–polyisocyanurate (RPU/PIR) foams were obtained. They were modified by ashes from burning paper (P) and wood: conifers (pine—S, spruce—S’) and deciduous trees (oak—D, birch—B). The ash was added to rigid polyurethane–polyisocyanurate foams (PU/PIR). In this way, five series of foams with different ash contents (from 1 to 9% wt.) were obtained: PP, PS, PD, PS’, PB. The model foam (reference—W) was obtained without filler. The basic properties, physico-mechanical, and thermal properties of the ashes and obtained foams were examined. It was specified, among other things, the cellular structure by scanning electron microscopy (SEM), and changes in chemical structure by Fourier-transform infrared spectroscopy (FTIR) were compared. The obtained foams were also subjected to thermostating in a circulating air dryer in increased temperature (120 °C) for 48 h. Ash tests showed that their skeletal density is about 2.9 g/cm³, and the pH of their solutions ranges from 9 to 13. The varied color of the ashes affected the color of the foams. SEM-EDS tests showed the presence of magnesium, calcium, silicon, potassium, aluminum, phosphorus, sodium, and sulfur in the ashes. Foam tests showed that pine ash is the most beneficial for foams, because it increases their compressive strength three times compared to W foam and improves their thermal stability. All ashes cause the residue after combustion of the foams (retention) to increase and the range of combustion of the samples to decrease. Full article

A deep understanding of the material parameters and the behavior of sandwich panels, which are used in the construction industry as roof and façade cladding, is important for the design of these construction components. Due to the constant changes in the polyurethane (PU) foams used as a core material, the experimental database for the current foams is small. Nowadays, there is an increasing number of failures of façade and roof panels after installation. This article presents a variety of experimental investigations on sandwich panels from two manufacturers with a core of polyisocyanurate (PIR) rigid foam (density: 40 kg/m³). As part of this study, compression, tension, shear, and bending tests were performed in several spatial directions and over the range required by the standard. The results of the tests showed the orthotropy of the core material and the dependence of the material on the direction and type of load. The stress-strain curves showed linear and non-linear areas. Using the data from this experimental study, a numerical model was implemented which utilized the Hill yield criterion to represent the orthotropy of the core material. The present investigation suggests that the classical von Mises failure criterion, used in many studies, is not suitable for the foam system applied in these sandwich panels. Instead, the Tsai–Wu criterion is more appropriate for defining the failure stresses. Full article

Two series of rigid polyurethane–polyisocyanurate (PU/PIR) foams were obtained. They were modified using powder fillers, such as industrial food cocoa (K5–K15 foam) and instant freeze-dried coffee (KR-KR15) added in amounts of 5, 10 and 15 wt.%. W foam (reference) was obtained without filler. The foams were degraded in a climate chamber for 1 week, 2 weeks or 3 weeks. Appropriate temperature, humidity and UV radiation were set in the chamber, which did not change throughout the degradation process. The foams were also degraded in an oven for two days at 120 °C. The foam tests carried out indicated, among others, on the decrease in compressive strength along with the increase in the residence time of the samples in the chamber. Degraded foams also changed color. Foams containing 5% and 10% of industrial cocoa or freeze-dried coffee were more susceptible to degradation. The addition of 15% coffee or cocoa slows down the degradation process. In the present study, industrial food cocoa and instant freeze-dried coffee were used as modifiers of rigid PU/PIR foam. These fillers have two functions: they accelerate the biodegradation of foams and have antioxidant properties. Full article

The article compares the properties of bio-polyols obtained from white mustard (Sinapis alba) seed oil, which contain boron and sulfur atoms. Each of the bio-polyols was prepared by a different method of testing the efficiency of the incorporation of boron and sulfur atoms. All synthesis methods were based on the epoxidation of unsaturated bonds followed by the opening of epoxy rings by compounds containing heteroatoms. Two of the bio-polyols were subjected to additional esterification reactions of hydroxyl groups with boric acid or its ester. Three new bio-polyols were obtained as a result of the performed syntheses. The synthesized compounds were subjected to detailed physicochemical (physical state, color, smell, density, viscosity and pH), analytical (hydroxyl number, acid number, water content, content of C, H, N, S, O, B elements and GPC analysis), spectroscopic (FTIR, ¹H NMR and ¹³C NMR) and thermal (DSC) tests. The obtained results allowed for a detailed characterization of the synthesized bio-polyol raw materials. Their suitability for obtaining polyurethane materials was also determined. The synthesized compounds have been found to be an interesting alternative to petrochemical polyols. The influence of the synthesized compounds on the flammability of polyurethane materials was tested experimentally. On the basis of this testing, a number of rigid polyurethane/polyisocyanurate foams were obtained, which were then subjected to flammability tests with the methods of horizontal and vertical burning, limiting oxygen index (LOI) and using the cone calorimeter. Based on this research, it was found that the presence of sulfur and boron heteroatoms reduced the flammability of polyurethane materials based on synthesized bio-polyols. Full article

Polyurethane material is used as an interior finish and wall cavity insulation. Flame-retardant products may be used for ignition, flame diffusion, and heat-release blocking. A large-scale test was conducted to understand the flame propagation characteristics of polyurethane with the addition of a flame retardant. The fire propagation properties and fire risks of four commonly used polyurethane materials were examined using three tests. Specifically, ignition properties, flame propagation behavior, and flashover occurrence were probed using full-scale tests, while heat release and fire characteristics were examined using cone calorimeter tests, and the toxicity of gaseous combustion products was assessed using gas toxicity tests. PIR F and PIR B, which contained flame retardants, featured slow flame propagation and a long-lasting residual flame, and PIR F released HCl and Br₂ on combustion. Full-scale tests revealed that although external flame propagation was always accompanied by flashover, irrespective of whether the flame retardant was present, a delay or blockage of energy transfer to the inside was observed for flame-retardant-containing specimens. Apart from checking the safety at the material level, the importance of identifying the actual fire characteristics through a full-scale test was confirmed. Full article

Incorporating biodegradable reinforcement, such as wood particles, into rigid polyurethane foams (RPUFs) is among the alternatives to reduce their environmental impact. This study aims to assess the effect of different wood particles as reinforcement in RPUFs. Reinforced rigid polyurethane foams are synthesized with milled wood particles of various forms and sizes and commercial polyol and isocyanate. The effect of fiber treatments and mechanical stirring on foams’ properties is also studied. Additional tests on polyisocyanurate foams (PIR) were undertaken to assess the effect of reinforcement on their properties. Mechanical properties are measured to investigate the impact of wood particle reinforcement on the foam. Confocal microscopy and Fourier-transform infrared spectroscopy (FTIR) showed the interaction between the wood fibers and the matrix. Despite the adhesion observed for some fibers, most of the cell walls of RPUFs were punctured by the rigid wood fibers, which explained the decrease in the compressive strength of the composites for manually mixed foams. Mechanical stirring proved to be an efficient method to enhance the reinforcement power of untreated fibers. RPUF foams’ properties showed similar changes when untreated wood flour was introduced to the formula, increasing compressive strength significantly. Full article

In this study, nineteen unmodified lignins from various sources (hardwood, softwood, wheat straw, and corn stover) and isolation processes (kraft, soda, organosolv, sulfite, and enzymatic hydrolysis) were used to replace 30 wt.% of petroleum-based polyol in rigid polyurethane/polyisocyanurate (PUR/PIR) foam formulations. Lignin samples were characterized by measuring their ash content, hydroxyl content (Phosphorus Nuclear Magnetic Resonance Spectroscopy), impurities (Inductively Coupled Plasma), and pH. After foam formulation, properties of lignin-based foams were evaluated and compared with a control foam (with no lignin) via cell morphology, closed-cell content, compression strength, apparent density, thermal conductivity, and color analysis. Lignin-based foams passed all measured standard specifications required by ASTM International C1029-15 for type 1 rigid insulation foams, except for three foams. These three foams had poor compressive strengths, significantly larger cell sizes, darker color, lower closed-cell contents, and slower foaming times. The foam made with corn stover enzymatic hydrolysis lignin showed no significant difference from the control foam in terms of compressive strength and outperformed all other lignin-based foams due to its higher aliphatic and p-hydroxyphenyl hydroxyl contents. Lignin-based foams that passed all required performance testing were made with lignins having higher pH, potassium, sodium, calcium, magnesium, and aliphatic/p-hydroxyphenyl hydroxyl group contents than those that failed. Full article

In this study, rigid polyurethane (PU) and polyisocyanurate (PIR) foam samples made from renewable material (tall oil fatty acid) based polyols were analyzed by pyrolysis gas chromatography mass spectrometry (Py-GC/MS) to obtain information about the full relative smoke content, with a focus on substance identification by their functional groups and hazardousness. The relative content of gaseous products produced during the thermal degradation was evaluated between the two samples, differenced by their assigned isocyanate (NCO) index value—150 and 300. The main thermal degradation components of the rigid PU-PIR foam were found to originate from the decomposition of isocyanate, primarily forming 4,4′-methylenedianiline, 3,3′-diaminodiphenylmethane, N-methylaniline, aniline, 4-benzylaniline and phenyl isocyanate. Hazard analysis revealed that the most common hazards were the hazards related to health: H315 (36%), H319 (28%), H335 (25%), and H302 (23%). The chemical compound with the highest relative content value—4,4′-methylenedianiline (45.3% for PU and 52.4% for PIR)—was identified to be a suspected carcinogen and mutagen. The focus of the study was identifying and evaluating the relative quantities of the produced gaseous products, examine their hazardousness, and provide information on the released thermal degradation products to form a renewable-source based rigid PU and PIR foam. Full article

The aim of the presented research was to obtain two new eco-polyols based on waste polylactide (PLA) and to check the effect on the properties of rigid polyurethane (RPU) foams and, based on these, rigid polyurethane/polyisocyanurate (RPU/PIR) foams. The synthesis of eco-polyols was based on the transesterification reaction of melted PLA with diethylene glycol in the presence of an organometallic catalyst. Properties of the obtained eco-polyols were examined for their potential as raw materials for synthesis of rigid polyurethane and polyisocyanurate foams, i.e., hydroxyl value, acid value, density, viscosity, pH, water content. Spectroscopic studies (FTIR, ¹H NMR and ¹³C NMR) were also carried out. Results of these tests confirmed the assumed chemical structure of the new polyols. RPU and RPU/PIR foam formulations were developed based on the obtained analytical results. Partial replacement of petrochemical polyol by eco-polyols in RPU and RPU/PIR foams decreased the value of apparent density, compressive strength, brittleness and water absorption. Moreover, all foams modified by eco-polyols showed higher resistance to aging. All RPU/PIR foams and most PRU foams modified by eco-polyols from waste PLA had better functional properties than the reference foams based on petrochemical polyol. Full article

Rigid polyurethane/polyisocyanurate (RPU/PIR) foam formulations were modified by evening primrose (Oenothera biennis) oil cake as a bio-filler in the amount of 5 to 50 wt.%. The obtained foams were tested in terms of processing parameters, cellular structure (SEM analysis), physico-mechanical properties (apparent density, compressive strength, brittleness, accelerated aging tests), thermal insulation properties (thermal conductivity coefficient, closed cells content, absorbability and water absorption), flammability, smoke emission, and thermal properties. The obtained results showed that the amount of bio-filler had a significant influence on the morphology of the modified foams. Thorough mixing of the polyurethane premix allowed better homogenization of the bio-filler in the polyurethane matrix, resulting in a regular cellular structure. This resulted in an improvement in the physico-mechanical and thermal insulation properties as well as a reduction in the flammability of the obtained materials. This research provided important information on the management of the waste product from the edible oil industry and the production process of fire-safe RPU/PIR foams with improved performance properties. Due to these beneficial effects, it was found that the use of evening primrose oil cake as a bio-filler for RPU/PIR foams opens a new way of waste management to obtain new “green” materials. Full article

The paper describes the preparation and characterization of rigid polyurethane-polyisocyanurate (PUR-PIR) foams obtained with biopolyol synthesized in the process of liquefaction of biomass from the Baltic Sea. The obtained foams differed in the content of biopolyol in polyol mixture (0–30 wt%) and the isocyanate index (I_ISO = 200, 250, and 300). The prepared foams were characterized in terms of processing parameters (processing times, synthesis temperature), physical (sol fraction content, apparent density) and chemical structure (Fourier transform infrared spectroscopy), microstructure (computer microtomography), as well as mechanical (compressive strength, dynamic mechanical analysis), and thermal properties (thermogravimetric analysis, thermal conductivity coefficient). The influence of biopolyol and I_ISO content on the above properties was determined. The addition of up to 30 wt% of biopolyol increased the reactivity of the polyol mixture, and the obtained foams showed enhanced mechanical, thermal, and insulating properties compared to foams prepared solely with petrochemical polyol. The addition of up to 30 wt% of biopolyol did not significantly affect the chemical structure and average cell size. With the increase in I_ISO, a slight decrease in processing times and mechanical properties was observed. As expected, foams with higher I_ISO exhibited a higher relative concentration of polyisocyanurate groups in their chemical structure, which was confirmed using principal component analysis (PCA). Full article

Four types of rigid polyurethane-polyisocyanurate foams (RPU/PIR) were obtained. Three of them were modified by powder fillers, such as cinnamon extract (C10 foam), green coffe extract (KZ10), and cocoa extract (EK10) in an amount of 10 wt %. The last foam was obtained without a filler (W foam). The basic properties and thermal properties of obtained foams were examined. All foams were subjected to degradation in the climatic chamber acting on samples of foams in a defined temperature, humidity, and UV radiation for 7, 14, and 21 days. The physico-mechanical properties of foams were tested. The compressive strength of degraded foams after 7, 14, and 21 days was compared with the compressive strength of nondegraded foams (0 days). The chosen properties of degraded foams, such as cellular structure by scanning electron microscopy (SEM) and changes of chemical structure by FTIR spectroscopy were compared. The obtained foams were also subjected to degradation in a circulating air dryer in an increased temperature (120 °C) for 48 h. Additionally, W, C10, ZK10, EK10 foams were placed in a soil environment and subjected to 28 days biodegradation process. The biochemical oxygen demand (BOD), the theoretical oxygen demand (TOD), and the degree of biodegradation (D_t) of foams were determined in this measurment. Test results showed that the compressive strength of foams decreased with the longer time of foam degradation in the conditioner. The foam subjected to degradation darkened and became more red and yellow in color. The addition of natural compounds of plant origin to foams increased their susceptibility to biodegradation. Full article

This article raised the issue of studies on the use of new bio-polyol based on white mustard seed oil and 2,2’-thiodiethanol (3-thiapentane-1,5-diol) for the synthesis of rigid polyurethane/polyisocyanurate (RPU/PIR) foams. For this purpose, new formulations of polyurethane materials were prepared. Formulations contained bio-polyol content from 0 to 0.4 chemical equivalents of hydroxyl groups. An industrial flame retardant, tri(2-chloro-1-methylethyl) phosphate (Antiblaze TCMP), was added to half of the formulations. Basic foaming process parameters and functional properties, such as apparent density, compressive strength, brittleness, absorbability and water absorption, aging resistance, thermal conductivity coefficient λ, structure of materials, and flammability were examined. The susceptibility of the foams to biodegradation in soil was also examined. The increase in the bio-polyol content caused a slight increase in processing times. Also, it was noted that the use of bio-polyol had a positive effect on the functional properties of obtained RPU/PIR foams. Foams modified by bio-polyol based on mustard seed oil showed lower apparent density, brittleness, compressive strength, and absorbability and water absorption, as well as thermal conductivity, compared to the reference (unmodified) foams. Furthermore, the obtained materials were more resistant to aging and more susceptible to biodegradation. Full article

This article presents the results of research on obtaining new polyurethane materials modified by a by-product from vegetable oils industry—rapeseed cake. The chemical composition of rapeseed cake was examined. Rigid polyurethane-polyisocyanurate (RPU/PIR) foams containing a milled rapeseed cake in their composition were obtained as part of the conducted research. Biofiller was added in amount of 30 wt.% up to 60 wt.%. Effects of rapeseed cake on the foaming process, cell structure and selected properties of foams, such as apparent density, compressive strength, brittleness, flammability, absorbability, water absorption, thermal resistance and thermal conductivity are described. The foaming process of RPU/PIR foams modified by rapeseed cake was characterized by a lower reactivity, lower foaming temperature and decrease in dielectric polarization. This resulted in a slowed formation of the polyurethane matrix. Apparent density of RPU/PIR foams with biofiller was higher than in unmodified foam. Addition of rapeseed cake did not have a significant influence on the thermal conductivity of obtained materials. However, we observed a tendency for opening the cells of modified foams and obtaining a smaller cross-sectional area of cells. This led to an increase of absorbability and water absorption of obtained materials. However, an advantageous effect of using rapeseed cake in polyurethane formulations was noted. Modified RPU/PIR foams had higher compressive strength, lower brittleness and lower flammability than reference foam. Full article

Two series of rigid polyurethane-polyisocyanurate foams (RPU/PIR) modified by cinnamon extract (series C_0t and CU_0t) were obtained. One RPU/PIR series contained a commercial flame retardant (C_0t) in the formulation. The other was produced without its participation (CU_0t). The basic properties of obtained foams, e.g., apparent density, brittleness, water absorption, compressive strength, flammability were examined. Afterwards, both series of foams (C_0t and CU_0t) were subjected to degradation in the climatic chamber, acting on samples of foams a defined temperature, humidity and UV radiation for a seven days. In this way, two successive series of RPU/PIR foams were obtained, which were designated, respectively, C_1t and CU_1t, Chosen properties of degraded foams such as: compressive strength, cellular structure by scanning electron microscopy (SEM) and changes of chemical structure by FTIR spectroscopy were determined. Compressive strength and the aging resistance was also determined (against the coefficient of compressive strength variation (CV). The possible replacement of a commercial flame retardant in polyurethane formulations by the antioxidant raw material (cinnamon extract) was evaluated. Full article