Search Results (706)

The practical application of inorganic ferroelectric fillers in flexible piezoelectric composites is critically constrained by low polarization efficiency and severe interfacial incompatibility with polymer matrices. Herein, we report a multi-level in situ surface modification strategy that simultaneously addresses both limitations. High-purity one-dimensional tetragonal barium titanate nanofibers (BTO NFs) are first synthesized via sol–gel electrospinning combined with a two-step gradient annealing process, which precisely controls phase evolution and preserves structural continuity. To overcome the detrimental acid-induced degradation of BTO NFs during functionalization, a polydopamine (PDA) buffer layer is first conformally coated, followed by the liquid-phase deposition of a conductive polypyrrole (PPy) shell, forming a robust core–shell PPy@PBT NFs architecture. Incorporating only 4 wt% of these multifunctional fillers into a poly(vinylidene fluoride) (PVDF) matrix yields a dramatic enhancement in electromechanical performance. The resulting flexible piezoelectric energy harvesters achieve a piezoelectric coefficient (d₃₃) of 28.7 pC/N, an output voltage of 13 V, and an output current of 0.7 μA, representing substantial improvements over unmodified filler systems. This synergistic enhancement originates from the PDA-mediated interfacial stress transfer and the PPy-induced Maxwell–Wagner polarization intensification, establishing a robust and generalizable paradigm for high-performance flexible piezoelectric composites in self-powered wearable electronics. Full article

Escherichia coli (E. coli) is a microorganism commonly found in water and food matrices, and its rapid and accurate detection is crucial for maintaining public health and ensuring food safety. However, traditional molecularly imprinted polymer (MIP) sensors often face challenges such as tedious template removal and prolonged sensing times. This study develops a label-free bacterial molecularly imprinted sensor that utilizes the synergistic effect of polypyrrole (PPy) and multi-walled carbon nanotubes (MWCNTs) to achieve highly sensitive detection of E. coli. Based on the large specific surface area and superior conductivity of MWCNTs, as well as the favorable electrochemical polymerization properties of PPy, a PPy/MWCNTs composite film was fabricated via a one-step electropolymerization process. The prepared sensor exhibited excellent kinetic characteristics, with a template removal time of only 15 min, and could be regenerated and used for subsequent detection within 30 min. Under optimized conditions, the biosensor showed a satisfactory linear response over the concentration range of 10²–10⁸ CFU/mL, with a low detection limit of 65 CFU/mL (3σ/S). Furthermore, recovery experiments conducted in tap water and lemon juice samples yielded satisfactory recoveries ranging from 87.1% to 114.8%, demonstrating the reliability and practical applicability of the proposed sensor for bacterial detection in real samples. This sensor offers advantages such as simple preparation, low material cost, and high sensitivity, providing a reliable and practical analytical platform for the rapid and reliable detection of bacteria. Full article

The development of reliable electrochemical interfaces for biosensor applications requires materials that combine high conductivity, large effective surface area, and suitable platforms for biomolecule immobilization. In this work, a hybrid electrochemical platform based on screen-printed carbon electrodes (SPCEs) modified with electropolymerized polypyrrole (PPy) and electrodeposited silver particles (AgPs) is presented for the subsequent immobilization of Ki-67 antibodies. PPy films were synthesized under optimized electrochemical conditions, producing homogeneous, porous, and electrochemically stable coatings that significantly enhanced the doping/undoping processes from 0.3280 C/0.3284 C to 0.3281 C/0.3284 C for SPCE and SPCE-PPy, respectively. Subsequently, silver particles were deposited onto the PPy matrix, resulting in a well-dispersed and uniform distribution of AgPs, promoted by the interaction between Ag⁰ and the nitrogen groups in the polymer backbone. The synergistic combination of PPy and AgPs resulted in improved charge-transfer properties and enhanced electrochemical reversibility, thereby decreasing the peak-to-peak separation of the ferricyanide/ferrocyanide redox couple used as a probe by 40%. Immobilization of Ki-67 antibodies was achieved via direct interaction with AgPs, resulting in a marked passivation effect, as evidenced by the suppression of redox probe signals, confirming successful biofunctionalization. The proposed SPCE-PPy-AgP architecture provides a robust, reproducible, and versatile platform for antibody immobilization, as demonstrated by oxidation and reduction peaks with relative standard deviations (RSDs) of 3.18% and 4.43%, respectively, highlighting its potential for developing label-free electrochemical immunosensors for clinically relevant proliferation biomarkers. Full article

Developing efficient and durable electrocatalysts for the alkaline hydrogen evolution reaction (HER) remains challenging due to intrinsically sluggish reaction kinetics and the limited long-term stability of many non-noble metal catalysts under continuous operation. Herein, a nickel-doped polypyrrole/chitosan composite electrode on stainless steel (PPy/Chi/Ni) was fabricated via electrodeposition as a low-cost and scalable method. Benefiting from the combined effects of Ni incorporation and the conductive polymer–biopolymer composite framework, the optimized PPy/Chi/Ni electrode exhibits enhanced HER activity in alkaline environment, delivering a low overpotential of η₁₀ = 78 mV at a current density of 10 mA·cm⁻² and a reduced Tafel slope of 93 mV·dec⁻¹, indicative of accelerated reaction kinetics. Structural and morphological characterizations by XRD, FTIR, and FESEM indicate the formation of the composite structure. FESEM images suggest that the deposited layer forms a relatively uniform coating on the stainless steel substrate. EIS further reveals improved interfacial charge-transfer characteristics upon Ni doping. Additionally, long-term stability tests confirm the structural integrity of the composite electrode and its electrochemical stability under HER conditions by demonstrating stable HER performance for 15 h with only a 22 mV potential change at a constant current density. By providing a conductive interface and numerous catalytic sites, the Ni-doped electrocatalyst coating activates the stainless steel substrate, leading to a 79% reduction in overpotential compared to bare stainless steel and thereby significantly improving its HER performance. Full article

To enhance the functionality of collagen (Coll)-based scaffolds, we developed a double-crosslinking strategy incorporating an electroconductive chitosan (Ch) and polypyrrole (Ppy) composite. Successful pre-crosslinking of Ch and Ppy was achieved using glutaraldehyde (GTA) at 100 µM. This facilitated imine linkage formation, confirmed by FTIR, enabling synergistic integration with Coll and successful nanofiber scaffold fabrication via electrospinning. While increasing the Ch-Ppy-GTA ratio affected the spinning process and higher GTA concentrations compromised fiber homogeneity, all other measured properties generally improved with increasing ratios. Crucially, this methodology allowed the membranes to maintain their morphology and significantly extended their degradation profile up to 20–30 days in PBS medium at 37 °C. Furthermore, the scaffolds exhibited electroactivity characterized by pseudocapacitance in the presence of Na⁺ and Ca²⁺ ions. These findings demonstrate a robust, tunable method for creating electroactive and structurally stable nanofiber scaffolds suitable for advanced tissue engineering. Full article

Molecularly imprinted polymers (MIPs) are widely employed for selective adsorption of target molecules in sensing and separation applications. The architecture of MIP films can influence adsorption behavior, interfacial stability, and reusability, yet systematic investigations of these effects are limited. This study aimed to evaluate how different polypyrrole (PPy) MIP film architectures affect the adsorption, stability, and regeneration characteristics of geraniol-imprinted layers on gold electrodes. Geraniol-imprinted and non-imprinted PPy films were electropolymerized onto quartz crystal microbalance (QCM) substrates. Two film architectures were compared: (i) a single-layer geraniol-imprinted PPy film, and (ii) a double-layer film consisting of a non-imprinted PPy underlayer followed by a geraniol-imprinted layer. Film characterization was performed using cyclic voltammetry (CV) and electrochemical quartz crystal microbalance (EQCM) measurements. Adsorption–desorption cycles were conducted to assess mass uptake, signal stability, and regeneration performance. EQCM analysis revealed that the double-layer architecture exhibited enhanced frequency signal stability during repeated adsorption–desorption cycles compared to single-layer films, suggesting a stabilizing effect of the underlying non-imprinted PPy layer at the electrode interface. Geraniol-imprinted films demonstrated significantly higher mass uptake than non-imprinted controls, confirming the sensitivity provided by molecular imprinting. Single-layer films showed more variability in signal response and less consistent regeneration performance. The architecture of MIP films significantly affects adsorption behavior, stability, and regeneration on electrode surfaces. Incorporating a non-imprinted PPy underlayer can improve signal reproducibility and enhance the robustness of MIP-based sensing interfaces. These findings provide guidance for the rational design of MIP coatings for electrochemical sensors and QCM-active platforms. Full article

Early intervention is pivotal for mitigating the progression of Alzheimer’s disease (AD). This study presents an electrochemical immunosensor targeting synaptic vesicle glycoprotein 2A (SV2A) to facilitate early AD diagnosis. A sensing interface was engineered using a nanocomposite of graphene oxide (GO) and 3-carboxyl polypyrrole (3-COOH-PPy). Leveraging the synergistic effects between the large specific surface area of GO and the superior conductivity of 3-COOH-PPy, the composite established an efficient electron transport network. This architecture provided abundant active sites for capture antibody immobilization while significantly enhancing interfacial electron transfer kinetics. Coupling this interface with an enzyme-mediated signal amplification strategy based on the horseradish peroxidase (HRP)-catalyzed TMB/H₂O₂ system, the immunosensor achieved high sensitivity. It exhibited a wide linear range of 2 ng/mL to 16 μg/mL with a low limit of detection (LOD) of 0.15 ng/mL. Furthermore, successful detection in C57 mouse serum samples validated the method’s reliability and potential for clinical application. In conclusion, this immunosensor offers a sensitive and robust platform for the early diagnosis of AD. Full article

Flexible electrode materials with tailored electrical and mechanical properties are essential for reliable electrocardiographic (ECG) sensing. In this work, p-toluenesulfonic-acid-doped polypyrrole (PPy–TSA) films were modified using polymeric and inorganic fillers, as well as their combinations (polyethylene glycol, graphene, carbon nanotubes, and zeolite), to tune their functional performance. The reference PPy–TSA film exhibits typical morphological and chemical characteristics of doped polypyrrole and serves as a reliable baseline for comparison. All composite films retain electrical conductivity within the range required for ECG applications while showing improved mechanical compliance (i.e., enhanced ability to conform to the skin and sustain deformation). Based on the optimized balance between electrical and mechanical properties, flexible ECG electrodes were fabricated using the TSA-doped PPy-based composite film. ECG recordings obtained with the several proposed electrodes show good agreement with those acquired using a commercial ECG electrode, demonstrating the potential of PPy-based composite films for flexible bioelectronic sensing applications. Full article

This study investigates the combined effect of electrodeposited gold nanoparticles (AuNPs) and AuNP–polypyrrole (PPy)-modified Saccharomyces cerevisiae on electrochemical glucose sensing. AuNPs were deposited onto electrode surfaces by cyclic voltammetry, and the resulting interfaces were characterized using atomic force microscopy, cyclic voltammetry, and electrochemical impedance spectroscopy. AFM analysis confirmed increased surface roughness and height variability after deposition, indicating substantial restructuring of the electrode interface. Electrochemical measurements showed that AuNP deposition altered interfacial charge storage and transfer and increased the measured charge-transfer resistance. Glucose sensing was evaluated in a ferricyanide-mediated system using yeast layers with or without AuNP and PPy modification over a 0–60 mM concentration range. All configurations exhibited saturating, non-linear glucose responses described by Hill fitting. Among the evaluated yeast-modified electrodes, the AuNP–PPy modified yeast produced the strongest glucose-induced current increase and the best low-concentration performance, achieving a limit of detection of 0.540 mM, compared with 1.016 mM and 1.330 mM for single-modified layers and 3.360 mM for unmodified yeast. These results show that combining AuNP electrodeposition with AuNP–PPy yeast modification improves interfacial properties and enhances mediator-assisted electrochemical glucose sensing. Full article

In this work, a polypyrrole–tungsten disulfide (PPy–WS₂) nanocomposite was synthesized through oxidative polymerization and evaluated as an electrode material for supercapacitors. Structural and morphological analyses confirmed the successful integration of WS₂ within the PPy matrix. Electrochemical testing revealed a high specific capacitance of 816 F g⁻¹ at a scan rate of 1 mVs⁻¹, together with excellent cycling durability. To further assess device-level performance, an asymmetric supercapacitor was assembled using the PPy–WS₂ nanocomposite as the positive electrode, activated carbon as the negative electrode, and a PVA/KOH gel electrolyte. The device achieved an energy density of 41.6 Wh kg⁻¹ and a power density of 1500 W kg⁻¹, while maintaining 105% of its capacitance after 2500 charge–discharge cycles. The prototype was also able to power a light-emitting diode, highlighting its practical potential. These findings demonstrate that the synergistic coupling between polypyrrole and tungsten disulfide substantially improves electrochemical behaviour, positioning the PPy–WS₂ nanocomposite as a promising candidate for advanced energy storage applications. Full article

Polypyrrole-based functional composites are increasingly explored and extensively adopted for energy storage, sensing, and environmental applications due to their tunable electronic properties, chemical versatility, and mechanical stability. However, rational optimization of these composites requires a unified understanding of electronic, mechanical, thermal, and chemical behavior at the atomic scale, which underlies their multifunctional behavior, and remains fragmented. Notably, Density Functional Theory (DFT) provides indispensable atomistic insight into the electronic, mechanical, thermal, and chemical interactions that govern the performance of multifunctional materials. To bridge these gaps, this review presents a comprehensive assessment of recent DFT and time-dependent DFT (TD-DFT) studies that elucidate the electronic, mechanical, thermal, and chemical characteristics of polypyrrole and its hybrid composites. Key theoretical descriptors, including electronic structure modulation, charge transfer behavior, adsorption energetics, interfacial binding energies, hydrogen bond formation, and charge redistribution, are critically assessed to establish structure–property relationships across diverse functional systems. Considerable attention is given to interfacial interactions, doping strategies, and composite architectures that govern durability, conductivity, and chemical stability. By consolidating current atomistic insights and identifying existing limitations, this review provides a coherent framework for rational material design. Notably, it presents the first systematic quantification of dopant steric effects in PPy multifunctional composites, linking atomistic-scale modifications to the optimization of functional properties in next-generation applications. Full article

Conducting polymers (CPs) have become cornerstone materials in electrochemical sensors and biosensors due to their mixed ionic–electronic conduction, mechanical softness, and intrinsic biointerface compatibility. This review provides a comprehensive and critical overview of the field, tracing the evolution of CP-based devices from classical poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS), polyaniline (PANI), and polypyrrole (PPy) electrodes to emerging nanostructured, hybrid, wearable, and transient systems. We discuss fundamental charge-transport mechanisms, doping strategies, structure–property relationships, and the role of morphology and biofunctionalization in dictating sensitivity, selectivity, and stability. Particular emphasis is placed on reliability challenges—including drift, dopant leaching, environmental degradation, and biofouling—and on the current lack of standardized metrology, which hampers cross-study comparability. We propose a framework for rigorous calibration, reference electrode design, and data reporting, enabling quantitative benchmarking across materials and architectures. To support meaningful cross-platform comparison, representative performance envelopes—including conductivity, limit of detection, sensitivity, selectivity strategies, and operational stability—are critically benchmarked across major CP families and sensing modalities. Finally, we explore future directions such as organic mixed ionic–electronic conductors, biohybrid and living polymer interfaces, Artificial Intelligence-driven modeling, and sustainable transient electronics. Full article

The catalyst in methanol oxidation plays a pivotal role in direct fuel cell reaction. The aim of this work is to study the influence of polypyrrole polymer (PPy) added in the carbon Vulcan support for the methanol oxidation reaction. The catalytic active phase synthesized was nickel-based materials, which have been demonstrated to exhibit remarkable chemical stability in alkaline solutions. The metallic-active phase was supported at the PPy-carbon Vulcan matrix. PPy is a conductor polymer and the research of electric conduction in synergy with a carbon Vulcan and a Ni catalyst is scarcely reported. The morphology characterization of composite catalytic material was carried out by XRD, XPS, and TEM techniques. In turn, the catalytic activity of the composite is characterized by means of cyclic voltammetry (CV). Electrochemical impedance spectroscopy (EIS) showed the influence of PPy on the charge transfer resistance (Rch. t.). The results indicate that a decrease in the Rch. t. was associated with an increase in methanol oxidation; therefore, higher amounts of charge transfer is produced. Furthermore, the DEMS technique corroborates the EIS results, confirming elevated conversion toward oxidation products. In turn, the selectivity of the composite-catalytic support on the methanol oxidation was elucidated using in situ Raman spectroscopy. Full article

Conductive hydrogels that simultaneously exhibit high mechanical robustness, reliable electrical conductivity, and interfacial adhesion are highly desirable for flexible sensing applications; however, achieving these properties in a single system remains challenging due to intrinsic structure–property trade-offs. Herein, a multifunctional conductive hydrogel (ASP hydrogel) is developed based on a polyacrylamide (PAM)/sodium alginate (SA) double-network architecture using a gallic acid (GA)–Fe³⁺–pyrrole (Py) coupling strategy. In this design, GA provides metal-coordination sites for Fe³⁺, while Fe³⁺ simultaneously serves as an oxidant to trigger the in situ polymerization of pyrrole, enabling the homogeneous integration of polypyrrole (PPy) conductive networks within the hydrogel matrix. The resulting ASP hydrogel exhibits a markedly enhanced fracture strength of 2.95 MPa compared with PAM (0.26 MPa) and PAM–SA (0.22 MPa) hydrogels, together with stable electrical conductivity and reproducible strain-dependent electrical responses. Moreover, the introduction of dynamic metal–phenolic coordination and hydrogen-bonding interactions endows the hydrogel with intrinsic self-healing capability and strong adhesion to diverse substrates. Rather than relying on simple filler incorporation, this work demonstrates an integrated network design that balances mechanical strength, conductivity, and adhesion, providing a versatile material platform for flexible strain sensors and wearable electronics. Full article

Conductive polymers (CPs), such as polypyrrole (PPy), have shown promising properties for use as electro-responsive bioactive scaffolds for tissue regeneration. PPy can be synthesized by chemical electrosynthesis and doped with biomolecules such as hyaluronic acid (HA). Taking advantage of the electrochemical synthesis versatility, nanofibers for surface-modified indium tin oxide (ITO) electrodes can be used as templates to produce tridimensional HA-doped PPy scaffolds. In this study, polyvinyl alcohol/chitosan (PVA/CTS) electrospun nanofibers deposited on ITO electrodes were used as a 3D template for the in situ electrosynthesis of HA-doped PPy to produce a bioactive scaffold for tissue engineering. The final material gathers the advantages of each biopolymer, the porous morphology of the nanofiber, and the conductivity of the electrosynthetized polymer. Furthermore, the biological activity of the NF-PVA/CTS@PPy:HA composite was evaluated in NIH-3T3 fibroblasts by MTT, resulting in a cell viability of 146 ± 40% and wound-healing capacity of 97 ± 1.9% at 24 h of culture. Full article