Search Results (73)

With the implementation of the ISO 8217-2024 marine fuel standard, the use of high-concentration biofuels in ships has become viable. However, relatively few studies have been conducted on the effects of biofuels on cylinder lubrication performance in low-speed, two-stroke marine diesel engines. In this study, catering waste oil was blended with 180 cSt low-sulfur fuel oil (LSFO) to prepare biofuels with volume fractions of 24% (B24) and 50% (B50). These biofuels were evaluated in a MAN marine diesel engine under load conditions of 25%, 50%, 75%, and 90%. The experimental results showed that, at the same engine load, the use of B50 biofuel led to lower kinematic viscosity and oxidation degree of the cylinder residual oil, but higher total base number (TBN), nitration level, PQ index, and concentrations of wear elements (Fe, Cu, Cr, Mo). These results indicate that the wear of the cylinder liner–piston ring interface was more severe when using B50 biofuel than when using B24 biofuel. For the same type of fuel, as the engine load increased, the kinematic viscosity and TBN of the residual oil decreased, while the PQ index and the concentrations of Fe, Cu, Cr, and Mo increased, reflecting the aggravated wear severity. Ferrographic analysis further revealed that ferromagnetic wear particles in the oil mainly consisted of normal wear debris. When using B50 biodiesel, a small amount of fatigue wear particles were detected. These findings offer crucial insights for optimizing biofuel utilization and improving cylinder lubrication systems in marine engines. Full article

The lubrication performance of the cylinder liner–piston ring (CLPR) is crucial for the energy efficiency and operating reliability of marine diesel engines. To enhance the boundary lubrication of marine engine oil, a 1,3-diketone fluid HPTD (1-(4-hexylphenyl) tridecane-1,3-dione, HPTD) was introduced as an ash-free friction modifier. Besides that, octadecylamine-functionalized nanocopper particles (ODA-Cu) were also added to the marine oil to improve its anti-wear behavior. Through cylinder-on-disk friction tests, the appropriate contents of HPTD and ODA-Cu were determined, which then formed hybrid additives and modified the engine oil. The tribological performance of the modified oil was analyzed under various normal loads, reciprocating frequencies, and testing temperatures. Based on the synergy of the tribochemical reaction of HPTD and the mending effect of ODA-Cu on the sliding surface, the modified oil not only had lower sulfated ash content but also exhibited superior lubrication performance (i.e., reduced coefficient of friction by 15%, smaller wear track by 43%, and higher maximum non-seizure load by 11%) than the pristine engine oil. The results of this study would be helpful for the design of novel hybrid eco-friendly additives for marine engine oil. Full article

This experimental study investigates the critical role and impact of additive concentration in enhancing the tribological performance of castor oil as a biolubricant for agricultural tractor engines. Friction and wear are major contributors to reduced engine efficiency, highlighting the need for effective lubrication strategies. While biolubricants like castor oil offer environmental benefits, they often require additives to achieve optimal performance. However, the concentration of these additives is crucial, as an imbalance can negatively impact the lubrication system, leading to a higher coefficient of friction, increased wear, and reduced engine efficiency and lifespan. This study examines the effects of varying concentrations of a mixture of propyl gallate (PG) and ionic liquid (IL) additives on the tribological performance of castor oil. The tribological behaviour of lubricated top compression piston ring and cylinder liner samples was evaluated under simulated engine conditions using a Bruker UMT Tribolab test rig, in accordance with the ASTM G181 standard. The experimental results revealed an influence of additive concentration on the coefficient of friction and wear behaviour. This emphasises the importance of optimising additive formulations to minimise engine wear and friction. Notably, a 0.5% volume concentration of the additive mixture led to a remarkable 34.8% reduction in the average coefficient of friction (COF) and a lower wear rate. Full article

In this work, 1,3-diketone synthesized via the Claisen condensation method and nano-copper particles modified by the Brust–Schiffrin method were added into a commercial marine medium-speed diesel engine cylinder piston oil to evaluate their effects on boundary lubrication performance. Friction and wear tests conducted on CKS-coated piston ring and cast-iron cylinder liner samples demonstrated significant reductions in both friction and wear with the addition of 1,3-diketone and nano-copper particles. Compared to the original oil without additives, the friction force was reduced by up to 16.7%, while the wear of the piston ring and cylinder liner was decreased by up to 21.6% and 15.1% at 150 °C, respectively. A worn surface analysis indicated that the addition of 1,3-diketone and functionalized nano-copper particles influenced the depolymerization and tribo-chemical reactions of the anti-wear additive ZDDP (zinc dialkyldithiophosphate) in the original engine oil. This modification enhanced the oil’s anti-friction and anti-wear properties, offering valuable insights into the development of eco-friendly lubricants for energy-efficient systems. Full article

This study evaluates the tribological characteristics of quasi-monolithic engine cylinder coatings and piston rings using a custom-built linear reciprocating tribometer. The coatings were deposited on an Al-Si alloy cylinder bore using the Plasma Transfer Wire Arc (PTWA) and Electrolytic Jet Plasma Oxidation (EJPO) processes. The coatings’ tribological performances were investigated in the boundary lubrication regime. The performance of conventional chrome-coated cast iron piston rings was tested and compared to that of EJPO- and PTWA-coated engine cylinder samples that were extracted from a cast Al-Si engine block. Scanning electron microscopy and profilometry were used to compare the evolution of wear and the prevalent wear mechanism. This paper also presents the verification and repeatability analysis of a custom-built tribometer against a standard industry-calibrated tribometer. The wear test results showed that the EJPO coating had 0.05% to 10.35% lower wear rates than its PTWA counterpart throughout a wide range of loading conditions and sliding distances. The variation in the counter-face behavior is likely due to the different surface topographic parameters such as skewness, kurtosis, and porosity. Full article

This research follows closely previous findings in flow characteristics and phenomena that take place in the piston ring and cylinder liner interface during motoring and firing engine operation, and also compares results between different optical engine set-ups. Cavitation visualisation in a simulating lubrication single-ring test rig and oil transport and cavitation visualisation in custom made cylinder assemblies of optical engines are the tools used to quantify the transport process under the piston ring and cylinder liner. Simplification of the interface is an essential technique that enhances the researcher’s confidence in results interpretation. Engine complexity and severe oil starvation are impeding the analysis of the experimental results. Visualisation experiments constitute an effective way to test various lubricant types and assess their overall performance characteristics, including their properties and cavitation behaviour. The repeatability of the visualisation method establishes the parametric study effects and offers valuable experimental results. As a further step towards the lubricant composition effect, a link between the lubricant formulation and the operating conditions could be established as the oil performance is assessed with a view to its transport behaviour. Image processing is used to quantify the impact of cavitation on piston ring lubrication in conjunction with varied operating and lubricant parameters. The characteristics of the lubricant and the working environment have an impact on these types of cavities. Viscosity, cavitation, oil film thickness (OFT), lubricant shear-thinning characteristics and friction are all linked. Full article

This study presents the challenges arising during the numerical design and simulation of surface-microtextured piston rings. The evaluation of performance is based on the values of asperity and hydrodynamic friction, as well as the lubricant film thickness. The simulation tool AVL Excite Piston & Rings is used to perform the calculations. The aim of this study is to understand how selected surface pre-processing (pre-treatment) steps affect the calculations. Two methods are presented to achieve a realistic surface topography representative of a state after running-in. Pre-treatment is performed through metrological filtering and thresholding of the topography, and Gaussian smoothing of the virtually applied micro-texture array is carried out. The results show the anticipated behavior of decreasing asperity and hydrodynamic friction losses with the concurrent application of both techniques. Full article

Lubricating oil and cylinder liner surface textures can significantly reduce the friction coefficient between the piston ring and the cylinder liner, thereby improving engine performance. However, the friction-diminishing mechanisms between the lubricating oil and surface texture remain unclear. Properly combining lubricating oil and surface texture can achieve better friction reduction effects. This paper, based on a transient thermo-hydrodynamic model developed in MATLAB 2020a, conducted numerous simulation experiments to explore the matching characteristics of textured cylinder liners. The study provides theoretical support for the future selection of lubricating oils for textured cylinder liners. The results show that, within the range of the circular texture parameters used in this study, the texture radius is directly proportional to the reduction in friction mean effective pressure (FMEP), while the texture depth is inversely proportional to the FMEP reduction. At the same rotational speed, as the viscosity of the lubricating oil increases, the friction-reducing effect of the texture on the piston ring–cylinder liner pair decreases. When the texture depth is 2 μm, the engine speed is inversely proportional to the reduction in FMEP. As the texture depth increases from 2 μm to 6 μm, there is a significant change in the friction-reducing effect: for the 2 μm texture, the friction-reducing impact decreases with increasing lubricant viscosity, while for the 6 μm texture, the friction-reducing effect increases with increasing lubricant viscosity. Full article

Numerical investigations of capped T-ring (CTR) seals performance in reciprocating motion for landing gear shock absorber applications are presented. A lubrication model using the Elastohydrodynamic lubrication theory and deformation mechanics is developed in a multi-material contact zone, and a procedure for coupling fluid and deformation mechanics is introduced. By conducting Finite Element Method (FEM) simulations, the static contact pressure is obtained, which subsequently is used within the model developed herein consisting of a modified Reynolds equation and an asperity contact model, to calculate the fluid film pressure, and the deformation of the fluid channel is determined using an elastic deformation model applied to a multi-component multi-mechanical property channel. These computational results are used for estimations of the seal leakage and friction under various conditions. In addition, the influence of asperity orientation is compared with other parameters, such as sealing pressure and piston velocity. A correlation between asperity orientation and leakage was found, and a general trend of reduced leakage with longitudinally oriented asperities was established. Full article

During shearer operation, the piston rod is susceptible to wear from the invasion of pollutants, thus ruining the sealing ring in the hydraulic cylinder. This work attempts to conduct a systematic investigation of Cu-doped diamond-like carbon (Cu-DLC) film to improve the seal performance. The failure process of the cylinder was analyzed, and relevant parameters were determined. Several Cu-DLC films were deposited on the substrate of the piston rod in a multi-ion beam-assisted system, and their structures and combined tribological performances were investigated. The hardness of the film ranges from 27.6 GPa to 14.8 GPa, and the internal stress ranges from 3500 MPa to 1750 MPa. The steady-state frictional coefficient of the film ranges from 0.04 to 0.15; the wear rate decreases first and then increases, and it reaches its lowest (5.0 × 10⁻⁹ mm³/N·m) at 9.2 at.% content. a:C-Cu_9.2% film presents optimal combined tribological performances in this experiment. The modification mechanism of Cu-DLC film for the seal performance may come from the synergistic effects of (i) the contact force and friction-heat-induced film graphitization, (ii) Cu doping improves the toughness of the film and acts as a solid lubricant, and (iii) the transfer layer plays a role in self-lubrication. Full article

With the marine industry’s demands for carbon reduction and increased reliability, the friction and wear performance of marine engines is becoming increasingly important. MAX phase materials show great potential in marine engine tribopair materials due to their unique microstructure and performance. The typical MAX phase material Ti₃AlC₂ was combined with MoDTC and added to the lubricant containing ZDDP additive for the tribopair composed of chromium-based ceramic composite coated steel (CKS) piston rings and cast iron cylinder liners under impact-sliding conditions. Compared to Ti₃AlC₂ alone, the friction coefficient and wear depth of the designed composite additive MoDTC/Ti₃AlC₂ were reduced by 36.9% and 41.4%, respectively. The worn surface lubricated with the Ti₃AlC₂/MoDTC composite additive showed fewer scratches with significantly less plastic deformation and clearer honing grooves. The multi-component tribofilm containing FeS, MoS₂, MoO₃, ZnO, TiO₂, Al2O₃, unoxidised particles, short-chain phosphates, and some ZnS was present on the worn cylinder liner surface. The synergistic effect of Ti₃AlC₂, MoDTC and ZDDP additives in the lubricant can isolate the mutual contact, generate a solid tribofilm and reduce the scratching. This can provide some guidance for the development of high-performance lubricant additives under impact-sliding conditions. Full article

Engineering practice has demonstrated that seal failure can result in severe leakage and wear, reducing the efficiency of hydraulic systems and even leading to major safety risks. Currently, analyses of the thermal aspect of seal interfaces are relatively limited, with most studies focusing on mechanical analysis. However, in actual applications, temperature has a significant impact on sealing performance. In this paper, nonlinear elastomechanics, viscous fluid mechanics, micro-contact mechanics, micro-deformation theory, and thermodynamics are coupled to establish a mixed lubrication model considering the thermal effect. The reliability of the mixed lubrication model is verified through experiments, and the temperature distribution of the oil film in the sealing area and the temperature distribution of the seal ring are simulated. Finally, the effects of the reciprocating speed, root mean square roughness, fluid medium pressure, and seal pre-compression on seal friction force and leakage are investigated. The results show that the heat generated in the sealing area accumulates at the bottom of the V-ring. Under the same conditions, compared with the instroke, the temperature-rise area of the outstroke is biased to the left and the increase in temperature is greater. In addition, the piston rod speed and the preliminary compression of the seal ring have a greater impact on the overall seal friction force and leakage. Under a lower seal pre-compression, the RMS roughness has a great influence on the leakage and friction in the outstroke, while the impact of the internal stroke is limited. Full article

Axial piston pumps with compact structures and high efficiency are widely used in construction machinery. The efficiency and lifetime strongly depend on the tribological performance of the pump’s valve plate pair. To enhance the tribological performance of the valve plate pair, surface textures, and H-DLC coatings were fabricated to modify the CuAl10Fe5Ni5 surfaces. The influences of elliptic textures of different sizes and textured H-DLC coatings on the surface friction and wear properties of the valve plate surface under oil lubrication were evaluated using a ring-on-disk tribometer. The results reveal that the friction and wear properties of the CuAl10Fe5Ni5 surfaces are significantly enhanced by elliptic textures, and the friction coefficient and wear rate of textured CuAl10Fe5Ni5 with E90 are maximally decreased by 95% and 87%, respectively. Compared with the surface textures and H-DLC coatings, the textured H-DLC coating has the greatest ability to reduce wear and adhesion. The wear rate of the textured H-DLC coating is further reduced by 98%. This improvement can be explained by the synergistic effect of the elliptic textures and H-DLC coatings, which are attributed to the reduced contact area, debris capture, and secondary lubrication of the elliptic textures, and increased surface hardness. Full article

This article compares the tribological performance of coatings produced by PVD sputtering. Transition metal dichalcogenide (TMD) coatings doped with carbon (WSC and MoSeC) and nitrogen (WSN and MoSeN) and a conventional diamond-like carbon (DLC) coating are compared. The tribological evaluation was oriented towards the use of coatings on piston rings. Block-on-ring tests in a condition lubricated with an additive-free polyalphaolefin (PAO 8) and at temperatures of 30, 60, and 100 °C were carried out to evaluate the coatings in boundary lubrication conditions. A load scanner test was used to evaluate dry friction and scuffing propensity. In addition to WSN, all other TMD coatings (WSC, MoSeC, and MoSeN) exhibited lower friction than DLC in dry and lubricated conditions. The study reveals that WSC, among TMD coatings, offers promising results, with significantly lower friction levels than DLC, while demonstrating reduced wear and a lower risk of metal adhesion. These findings suggest that WSC may be a viable alternative to DLC in piston rings, with potential benefits for reducing fuel consumption and increasing engine durability. Full article

This work focuses on the evolution of lubrication wedge shaping in internal combustion piston engines, taking into account liquid microflows on curved surfaces and coating microgeometries. It introduces a new approach to the analysis of friction losses by simulating the microflow of lubricating oil between the surfaces of piston rings cooperating with the cylinder surface. The models used take into account three types of microgeometry and material expansion. Key results indicate that microirregularities with a stereometry of 0.1–0.2 µm significantly influence the distribution of oil film thickness in the phase of maximum working pressure, which is critical for the functioning of the seal ring. The innovation of the work consists of demonstrating that, despite small changes in the friction force and power in the piston rings, changes in the minimum values of the oil film thickness are significant. The work highlights the failure to take into account microgeometry parameters in friction models, which leads to significant errors in the simulation results, especially in terms of oil film continuity and the contribution of mixed friction. The simulations also indicate that advanced geometric models with high mesh resolution are necessary only for the assessment of changes in oil film thickness during the highest pressure increase in the combustion chamber and taking into account various mixed friction conditions. The results suggest significant progress in engine design and performance, confirming the importance of advanced fluid and mixed friction models in piston engine lubrication research. Full article