Search Results (64)

Clarifying the differential effects of temperature gradient and temperature change rate on the evolution of rock fractures and damage mechanism under thermal shock is of great significance for the development and utilization of deep geothermal resources. In this study, granite samples at different temperatures (20 °C, 150 °C, 300 °C, 450 °C, 600 °C, and 750 °C) were subjected to rapid cooling treatment with liquid nitrogen. After the thermal treatment, a series of tests were conducted on the granite, including wave velocity test, uniaxial compression experiment, computed tomography scanning, and scanning electron microscopy test, to explore the influence of thermal shock on the physical and mechanical parameters as well as the meso-structural damage of granite. The results show that with the increase in heat treatment temperature, the P-wave velocity, compressive strength, and elastic modulus of granite gradually decrease, while the peak strain gradually increases. Additionally, the failure mode of granite gradually transitions from brittle failure to ductile failure. Through CT scanning experiments, the spatial distribution characteristics of the pore–fracture structure of granite under the influence of different temperature gradients and temperature change rates were obtained, which can directly reflect the damage degree of the rock structure. When the heat treatment temperature is 450 °C or lower, the number of thermally induced cracks in the scanned sections of granite is relatively small, and the connectivity of the cracks is poor. When the temperature exceeds 450 °C, the micro-cracks inside the granite develop and expand rapidly, and there is a gradual tendency to form a fracture network, resulting in a more significant effect of fracture initiation and permeability enhancement of the rock. The research results are of great significance for the development and utilization of hot dry rock and the evaluation of thermal reservoir connectivity and can provide useful references for rock engineering involving high-temperature thermal fracturing. Full article

Glass ionomer cements (GICs) have been clinically attractive dental restorative materials for many years and are widely used as luting, lining, and restorative materials. However, these materials still have limitations in terms of weak physio-mechanical properties. The aim of the study was to evaluate the effect of zirconium oxide nanoparticles (nano-ZrO₂ particles) on the physical and mechanical properties of two commercially available GICs. Four groups were prepared for each material: the control group (without nanoparticles) and three groups modified by the incorporation of nanoparticles at 2, 5, and 7 weight% (wt%). Firstly, the morphology and size of the nanoparticles were evaluated via scanning electron microscopy (SEM) and X-ray diffraction (XRD). Secondly, flexural strength, flexural modulus, Vickers hardness, water sorption, and solubility were evaluated. The main effect plots revealed that the addition of nano-ZrO₂ particles enhances flexural strength, flexural modulus, and water sorption of GICs at a 7 wt% concentration and Vickers hardness at a 2 wt% concentration. The SEM analysis clearly shows that the cracks became narrower with the addition of nano-ZrO₂ particles, whereas these cracks were completely closed at 7% nano-ZrO₂ particles. The findings of the study appear promising, and it is anticipated that the optimization of nano-ZrO₂ particles may aid the development of improved materials for load-bearing restorations. Full article

Soil microorganisms provide multifaceted benefits, including maintaining soil nutrient dynamics, improving soil structure, and instituting decomposition, all of which are important to soil health. Unpredictable weather events, including flooding from heavy rainfall, flash floods, and seawater intrusion, profoundly impact soil ecology, which is primarily challenged by flooding stress, and imbalances these microbial communities and their functions. This disturbance impairs the symbiotic exchanges between microbes and plants by limiting root exudates and habitats for microbes, as well as nutrient acquisition efficiency for plants. Therefore, this review comprehensively examines the changes in soil microbial communities that occur under flooding conditions. Flooding reduces soil oxygen (O₂) levels, limiting aerobic microbes but promoting anaerobic ones, including potential pathogens. In flooded soil, O₂ deficiency indirectly depends on the size of the soil particles and water turbidity during flooding. O₂ depletion is critical in shaping microbial community adaptation, which is linked to variations in soil pH, nutrient concentrations, and redox status, and fresh and saline water vary differently in terms of the adaptation of microorganisms. Wet soil alters soil enzyme activity, which influences microbial community composition. Notably, three-month post-flooding conditions allow microbial communities to adapt and stabilize more effectively than once-weekly flooding frequency. Based on the presence of aboveground species, fungi are found to reduce under flooding conditions, while nematode numbers, surprisingly, increase. Direct and indirect impacts between soil microbes and physio-chemical properties indicate positive or negative feedback loops that influence the soil ecosystem. Over the years, beneficial microorganisms such as plant-growth-promoting microbes (PGPMs) have been identified as important in regulating soil nutrients and microbial communities in wetland environments, thereby enhancing soil health and promoting better plant growth and development. Overall, understanding the mechanisms of belowground ecosystems under flooding conditions is essential for optimizing agricultural practices and ensuring sustainable crop production in flood-prone areas. Full article

There has been growing interest and increasing attention in the field of functional clothing textiles, particularly in product and process development, as well as innovations in heat-generating, retaining, and releasing fibers to maintain a healthy body temperature without relying on unsustainable energy sources. This study, for the first time, reports the various physio-mechanical properties of surface-functionalized regenerated cellulose fibers (RCFs) coated with ceramic particles. The coating imparts photothermal conversion-based heat generation and retention properties with the aid of polyelectrolyte binders. In this design, ZrC enables the conversion of light energy into thermal energy, providing heat for the human body. A feasible coating process was employed, utilizing industrially feasible exhaustion methods to deposit the ZrC particles onto the RCF surface in conjunction with two distinctive polymeric binders, specifically polyethyleneimine (PEI) and polydiallyldimethylammonium chloride (polyDADMAC). The morphological characteristics and tensile properties of the coated RCFs were analyzed via scanning electron microscopy (SEM) and single-fiber tensile testing. Heat retention and release behaviors of a bundle of fiber samples were assessed using infrared (IR) imaging and an IR emission lamp setup. The SEM results confirmed the successful coating of the ZrC particles on the surface of the RCF samples, influencing negligible on their physical–mechanical properties. The heat retention of the coated RCFs with ZrC and both binders was higher than that of reference regenerated cellulose fibers (RCFs), demonstrating their effective heat generation, retention, and heat release properties. Based on the highlighted prominent results for the coated RCFs, these findings highlight the suitability of the developed functional clothing textiles for targeted applications in non-extreme thermal conditions, ensuring thermo-physiological comfort by maintaining body temperature within a tolerable thermal range (36.5–37.5 °C), in contrast to studies reporting significantly higher temperatures (50–78 °C) for extreme thermal conditions. Full article

Tissue-engineered biocompatible scaffolds could mimic the extracellular matrix structure for cell adhesion and proliferation; however, patients suffer from large volume implantation. In this study, a thermal sensitive shape memory polyurethane porous 3D scaffold based on poly(ε-caprolactone) and poly(ethylene glycol adipate) was developed, utilizing the water-splitting property of aliphatic hexamethylene diisocyanate (HDI) to crosslink rigid segments during the polymerization process. The chemical structure, microstructure, and morphology, as well as mechanical strength, of the scaffolds were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), a scanning electron microscope (SEM), and tensile tests. The results show that gas foaming action caused by the release of CO₂ occurred simultaneously in the reactive process, resulting in the interconnective porous structure of the PU scaffolds with a porosity of over 70% and pore sizes from 100 μm to 800 μm. Additionally, after programming to a temporary shape, the scaffolds could recover to their initial shapes and could be programmed into various shapes according to different defects. These smart shape-changeable scaffolds with high porosity and good physio-chemical properties are a promising material for minimally invasive tissue engineering. Full article

The impact of a glycerol–silicate (GS) plasticizer on the mechanical, thermal and hydrophobic properties pertaining to sodium alginate (NaAlg) and calcium alginate (CaAlg) films were investigated. Spectroscopic and physio-chemical analysis were conducted to evaluate the effects of the GS incorporation. The results determine that both NaAlg and CaAlg films exhibited poor mechanical properties which only improved by increasing the GS loading (up to 25 wt%), after which it declined. CaAlg exhibited the highest tensile strength after 25 wt% GS loading was incorporated. The elongation at break varied, with NaAlg films showing a ~10-fold increase, while the CaAlg films remained relatively unchanged. Thermal gravimetric analysis (TGA) revealed that GS reduced the onset decomposition temperature of NaAlg films, whereas CaAlg films maintained a greater onset decomposition temperature. The advancing contact angle measurements indicated a nearly linear decrease (from 54° to 39°) in hydrophobicity for the NaAlg films while the hydrophobicity for CaAlg films initially increased from 65° to 74°, and then became more hydrophilic with greater GS loading. These findings highlight the potential of GS plasticization to enhance and tailor alginate film properties, providing insights into the development of sustainable bioplastics with improved mechanical properties. Full article

The side effects associated with the chemotherapy of triple-negative breast cancer (TNBC), such as nucleotide-binding oligomerization domain (NOD)-like receptor family (NLR), pyrin domain containing 3 (NLRP3) inflammasome activity, are responsible for the treatment failure and high mortality rates. Therefore, advanced delivery systems have been developed to improve the transport and targeted administration of anti-tumor agents at the tumor sites using tissue engineering approaches. Implantable delivery systems based on biodegradable polymers are an effective alternative due high biocompatibility, porosity, and mechanical strength. Moreover, the use of paclitaxel (PTX)-cyclodextrin complexes increases the solubility and permeability of PTX, enhancing the bioavailability and efficacy of the drug. All of these properties contribute to the efficient encapsulation and controlled release of drugs, preventing the damage of healthy tissues. In the current study, we detailed the synthesis process and evaluation of 3D scaffolds based on gelatin functionalized with methacryloyl groups (GelMA) and pectin loaded with PTX–cyclodextrin inclusion complexes on TNBC pathogenesis in vitro and in vivo. Bio-physio-chemical analysis of the proposed scaffolds revealed favorable mechanical and biological properties for the cellular component. To improve the drug solubility, a host–guest interaction was performed by the complexation of PTX with a cyclodextrin derivative prior to scaffold synthesis. The presence of PTX suppressed the growth of breast tumor cells and promoted caspase-1 activity, the release of interleukin (IL)-1β, and the production of reactive oxygen species (ROS), conditioning the expression levels of the genes and proteins associated with breast tumorigenesis and NLRP3 inflammasome. The in vivo experiments suggested the activation of pyroptosis tumor cell death, confirming the in vitro experiments. In conclusion, the bio-mechanical properties of the GelMA and pectin-based scaffolds as well as the addition of the PTX–cyclodextrin complexes allow for the targeted and efficient delivery of PTX, suppressing the viability of the breast tumor cells via pyroptosis cell death initiation. Full article

Traditional pulp-capping materials like mineral trioxide aggregate (MTA) offer excellent biocompatibility and sealing, but limitations such as prolonged setting time, low bioactivity, and high costs persist. Metformin, with its potential in craniofacial regeneration, could enhance dentin synthesis by targeting pulp cells. This study aimed to: (1) develop a calcium phosphate cement with chitosan (CPCC) with improved physio-mechanical properties; (2) incorporate metformin (CPCC-Met) to assess release; and (3) evaluate human dental pulp stem cells (hDPSCs) response. CPCC was mixed at different powder-to-liquid ratios to evaluate physio-mechanical properties compared to MTA. The optimized CPCC formulation was loaded with 0, 50, 100, and 150 µg of metformin to measure release and assess hDPSCs attachment and proliferation (1, 4, and 7 d) via live/dead imaging and SEM. One-way ANOVA was used for statistical analysis. Results showed CPCC at a 3.25:1 ratio significantly reduced setting time to 41.5 min versus 123 min for MTA (p < 0.05). Metformin release correlated with concentration, and SEM confirmed the presence of a porous, hydroxyapatite-rich surface. Cell viability was consistently high across groups (>93% at 1 d, >95% at 4 d, ≈98% at 7 d), with no significant differences (p > 0.05). These findings suggest that the novel CPCC-Met demonstrates promise as a fast-setting, cost-effective pulp-capping material, offering metformin delivery to enhance dentin repair. Full article

Dimethylformamide (DMF), a polar solvent, is commonly used for preparing graphene/epoxy nanocomposites. While previous research has commonly predominantly highlighted the improvement in physio-mechanical properties of these nanocomposites, the effect of DMF on processing and its direct influence on the final characteristics of MXene/epoxy nanocomposites have not been investigated. This unexplored link between DMF dosage, MXene concentrations, and the final composite properties presents an exciting direction for future research. In this study, a fixed dosage of DMF was used with varying MXene concentrations to fabricate the nanocomposites. To assess the reliability of DMF dosage on the characteristics of the fabricated nanocomposites, various evaluation techniques were employed, including dispersion evaluation, mechanical tests, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), electromagnetic interference (EMI) shielding, and surface roughness measurements. The research outcomes revealed that as MXene concentration increased, the characteristics of the MXene/epoxy nanocomposites, improved across the board, indicating their potential for use in energy storage applications. Full article

Xylem-associated fungus can secrete many secondary metabolites to help Aquilaria trees resist various stresses and play a crucial role in facilitating agarwood formation. However, the dynamics of endophytic fungi in Aquilaria sinensis xylem after artificial induction have not been fully elaborated. Endophytic fungi communities and xylem physio-biochemical properties were examined before and after induction with an inorganic salt solution, including four different times (pre-induction (0M), the third (3M), sixth (6M) and ninth (9M) month after induction treatment). The relationships between fungal diversity and physio-biochemical indices were evaluated. The results showed that superoxide dismutase (SOD) and peroxidase (POD) activities, malondialdehyde (MDA) and soluble sugar content first increased and then decreased with induction time, while starch was heavily consumed after induction treatment. Endophytic fungal diversity was significantly lower after induction treatment than before, but the species richness was promoted. Fungal β-diversity was also clustered into four groups according to different times. Core species shifted from rare to dominant taxa with induction time, and growing species interactions in the network indicate a gradual complication of fungal community structure. Endophytic fungi diversity and potential functions were closely related to physicochemical indices that had less effect on the relative abundance of the dominant species. These findings help assess the regulatory mechanisms of microorganisms that expedite agarwood formation after artificial induction. Full article

The increasing awareness of global ecological concerns and the rising sustainability consciousness associated with the manufacturing of non-renewable and non-biodegradable composite materials have led to extensive research on product and process developments of more sustainable, environmentally friendly, and fully biodegradable biocomposites for higher-value end-use applications. All-cellulose composites (ACCs) are an emerging class of biocomposites, which are produced utilizing solely cellulose as a raw material that is derived from various renewable biomass resources, such as trees and plants, and are assessed as fully biodegradable. In this study, sustainable ACCs were fabricated for the first time based on the full dissolution of commercially available sulfite dissolving (D) pulps as a matrix with concentrations of 1.5 wt.% and 2.0 wt.% in an aqueous NaOH–urea solvent, and they were then impregnated on/into the pre-fabricated birch (B), abaca (A), and northern softwood (N) fiber sheets as reinforcements by the vacuum-filtration-assisted impregnation approach. This research aimed to investigate the effects of the impregnated cellulose matrix concentrations and types of the utilized cellulose fiber reinforcements (B, A, N) on the morphological, crystalline, structural, and physio-mechanical properties of the ACCs. The highest degrees of improvements were achieved for tensile strength (+532%, i.e., from 9.24 MPa to 58.04 MPa) and strain at break of the B fiber-reinforced ACC B_1.5 (+446%, i.e., from 1.36% to 4.62%) fabricated with vacuum impregnation of the 1.5 wt.% cellulose matrix. Noticeably, the greatest improvements were attained in strain at break of the A and N fiber-reinforced ACCs A_2.0 (+218%, i.e., from 4.44 % to 14.11%) and N_2.0 (+466%, i.e., 2.59% to 14.65%), respectively, produced with vacuum impregnation of the 2.0 wt.% cellulose matrix. The study highlights the diverse properties of the all-cellulose biocomposite materials that could, expectedly, lead to further development and research for upscaled production of the ACCs. Full article

Sirtuins (SIRTs) belong to the family of nicotine adenine dinucleotide (NAD⁺)-dependent class III histone deacetylases, which come into play in the regulation of epigenetic processes through the deacetylation of histones and other substrates. The human genome encodes for seven homologs (SIRT1-7), which are localized into the nucleus, cytoplasm, and mitochondria, with different enzymatic activities and regulatory mechanisms. Indeed, SIRTs are involved in different physio-pathological processes responsible for the onset of several human illnesses, such as cardiovascular and neurodegenerative diseases, obesity and diabetes, age-related disorders, and cancer. Nowadays, it is well-known that Citrus fruits, typical of the Mediterranean diet, are an important source of bioactive compounds, such as polyphenols. Among these, flavonoids are recognized as potential agents endowed with a wide range of beneficial properties, including antioxidant, anti-inflammatory, hypolipidemic, and antitumoral ones. On these bases, we offer a comprehensive overview on biological effects exerted by Citrus flavonoids via targeting SIRTs, which acted as modulator of several signaling pathways. According to the reported studies, Citrus flavonoids appear to be promising SIRT modulators in many different pathologies, a role which might be potentially evaluated in future therapies, along with encouraging the study of those SIRT members which still lack proper evidence on their support. Full article

In this work, a 3D printing methodology based on the robocasting of catalytic ink pastes was applied to obtain structured matrix-like cylinders as innovative materials for an effective utilization of carbon dioxide. The influence of three different binders (i.e., PEI, HPMC and MC) on the physio-chemical, mechanical and catalytic properties of multi-channel monoliths was studied against a reference binder-free powdered system in order to envisage the effectiveness of the printing procedure in realizing hybrid advanced materials at a higher control and reproducibility than from traditional preparation techniques. In terms of textural and structural properties, the micro-extruded 3D cylinders only evidenced a slight difference in terms of relative crystallinity, with minor effects on the surface area exposure in relation to the specific binder used during the direct ink writing process. More importantly, the typology of binder significantly affected the rheological properties of the catalytic ink, with the need of a controlled viscosity to ensure a suitable thixotropic behaviour of the extrudable pastes, finally determining an optimal mechanical resistance of the final 3D monolith. The experimental validation of the hybrid multi-channel cylinders under conditions of CO₂ hydrogenation demonstrated the great potential of additive manufacturing in the realization of catalyst architectures characterized by unique features and fidelity scarcely reproducible via conventional synthetic techniques. Full article

The widely used high-density polyethylene (HDPE) polymer has inadequate mechanical and thermal properties for structural applications. To overcome this challenge, nano zinc oxide (ZnO) and nano boron oxide (B₂O₃) doped lignin-containing cellulose nanocrystals (L-CNC) were blended in the polymer matrix. The working hypothesis is that lignin will prevent CNC aggregation, and metal oxides will reduce the flammability of polymers by modifying their degradation pathways. This research prepared and incorporated safe, effective, and eco-friendly hybrid systems of nano ZnO/L-CNC and nano B₂O₃/L-CNC into the HDPE matrix to improve their physio-mechanical and fire-retardant properties. The composites were characterized using Fourier transform infrared spectroscopy, scanning electron microscopy, energy dispersive X-ray analysis, thermo-gravimetric analysis, differential scanning calorimetry, dynamic mechanical analysis, horizontal burning test, and microcalorimetry test. The results demonstrated a substantial increase in mechanical properties and a reduction in flammability. The scanning electron microscope (SEM) images showed some agglomeration and irregular distribution of the inorganic oxides. Full article

Dental implants can be made of various materials, and amongst them, titanium and titanium alloy were the materials of choice for dental implants for many years because of their biocompatibility. The two alloys have a high level of biocompatibility, a lower modulus of elasticity, and better corrosion resistance than other alloys. Thus, they are frequently utilized in biomedical applications and mostly replace stiff fabrics. The latest advances in a new strontium oxide–cp titanium composite alloy are the main topic of this research. With regard to biomedical applications, additions of strontium oxide were synthesized at three distinct weight percentages (2%, 4%, and 6% by wt%). Powder metallurgy was used to create the alloys, which were then sintered by heating the samples. The effects of adding strontium oxide were analyzed by utilizing measurements of the Brinell hardness, X-ray diffraction, porosity, diametral tensile strength, roughness, and wettability of the finished surfaces. The results show that adding more strontium oxide (gradually increasing the ratio from 2% SrO to a 6% addition) raised the roughness and porosity. However, the microhardness and diametral tensile strength were enhanced with an increase in the volume fraction of strontium oxide particles. In conclusion, the alloy that contained 6 wt% strontium oxide microparticles had reasonably high mechanical properties and might be regarded as suitable for use in dental and medical applications due to its high wettability or, in other words, its low contact angle. The Brinell testing results for the diametral tensile strength, microhardness, and porosity of the generated strontium oxide–cp titanium composite alloy demonstrate its high potential for usage as a biomaterial, particularly in dental applications. Full article