Search Results (112)

The (1−x)Ba_0.96Ca_0.04TiO₃−xBi(Li_1/3Zr_2/3)O₃ (x = 0.03–0.15) ceramics were fabricated via the traditional solid reaction method. Characterization results revealed that each component exhibited a pure perovskite structure, and the average grain size significantly diminishes with increasing x. The (1−x)Ba_0.96Ca_0.04TiO₃−xBi(Li_1/3Zr_2/3)O₃ ceramics exhibited prominent relaxor ferroelectric behavior, whose characteristic narrow hysteresis loops effectively enhanced the energy storage performance of the material. Most importantly, the composition with x = 0.10 demonstrated exceptional energy storage properties at 150 kV/cm, achieving a high recoverable energy storage density (W_rec = 1.91 J/cm³) and excellent energy efficiency (η = 90.87%). Under the equivalent electric field, this composition also displayed a superior pulsed discharge performance, including a high current density (871 A/cm²), a high power density (67.3 MW/cm³), an ultrafast discharge time (t_0.9 = 109 ns), and a discharged energy density of 1.47 J/cm³. These results demonstrate that the (1−x)Ba_0.96Ca_0.04TiO₃−xBi(Li_1/3Zr_2/3)O₃ ceramic system establishes a promising design paradigm for the creation and refinement of next-generation dielectrics for pulse power applications. Full article

Barium stannate (BaSnO₃) has emerged as a promising alternative electron transport material owing to its superior electron mobility, resistance to UV degradation, and energy bandgap tunability, yet BaSnO₃-based perovskite solar cells have not reached the efficiency levels of TiO₂-based designs. This theoretical study presents a design-driven evaluation of BaSnO₃-based perovskite solar cell architectures, incorporating MAPbI₃ or FAMAPbI₃ perovskite materials, Spiro-OMeTAD, or Cu₂O hole transport materials as well as hole-free configurations, under varying light intensity. Using a systematic device modelling approach, we explore the influence of key design variables—such as layer thickness, donor density, and interface defect concentration—of BaSnO₃ and operating temperature on the power conversion efficiency (PCE). Among the proposed designs, the FTO/BaSnO₃/FAMAPbI₃/Cu₂O/Au heterostructure exhibits an exceptionally effective arrangement with PCE of 38.2% under concentrated light (10,000 W/m², or 10 Sun). The structure also demonstrates strong thermal robustness up to 400 K, with a low temperature coefficient of −0.078% K⁻¹. These results underscore the importance of material and structural optimisation in PSC design and highlight the role of high-mobility, thermally stable inorganic transport layers—BaSnO₃ as the electron transport material (ETM) and Cu₂O as the hole transport material (HTM)—in enabling efficient and stable photovoltaic performance under high irradiance. The study contributes valuable insights into the rational design of high-performance PSCs for emerging solar technologies. Full article

To develop eco-friendly low-temperature NH₃-SCR catalysts for the non-electric industry, a series of CeMn-modified Ba₂Ti₅O₁₂ catalysts were synthesized using the sol-gel method to achieve denitrification. Activity tests revealed that Ce-Mn-modified Ba₂Ti₅O₁₂ catalysts exhibit excellent low-temperature denitrification performance with a broad operational temperature window. Characterization through XRD, XPS, BET, NH₃-TPD, and EPR indicated that Ce-Mn modification enhances surface oxygen chemisorption and increases acidity, significantly improving NO_x reduction. Notably, the optimal catalyst achieved NO_x conversion rates exceeding 90% within the temperature range of 90 to 240 °C under a gas hourly space velocity (GHSV) of 28,000 h⁻¹. In particular, the coexistence of Ce and Mn species promotes the oxidation of NO to NO₂, facilitating the “fast SCR” reaction. The abundance of valence states further enhances the catalyst’s ultra-low-temperature NH₃-SCR denitration performance. Full article

In order to reduce the sintering temperature, MnO₂ was used as a sintering aid to prepare [(Ba_0.85Ca_0.15)_0.999(Dy_0.5Tb_0.5)_0.001](Zr_0.1Ti_0.9)O₃-x mol% MnO₂ (BCDTZT-x mol% MnO₂, x = 0.05, 0.2, 0.4, 0.6, 0.8, 1, 1.5, 3) lead-free piezoelectric ceramics in which the effects of the MnO₂ doping amount and sintering temperature on the phase structure, sintering behavior, and electrical properties of the BCDTZT-x mol% MnO₂ ceramics were systematically analyzed. All ceramics have a single perovskite structure and coexist in multiple phases. The optimal sintering temperature was reduced from 1515 °C to 1425 °C, and the density of all ceramics was increased as compared with the undoped ceramic, reaching a maximum of 5.38 g/cm³ at x = 0.8 mol%. An appropriate MnO₂ doping amount of 0.4 mol% could effectively suppress oxygen vacancies and improve electrical properties, resulting in the best comprehensive performance of the ceramics, with a dielectric constant maximum of 12,817, a high piezoelectric constant of 330 pC/N, and good strain value (S_max = 0.118%) and low strain hysteresis (Hys = 2.66%). The calculation of activation energy indicated that the high-temperature conductivity was dominated by oxygen vacancies in all ceramics. The results showed that the appropriate introduction of MnO₂ as a sintering aid could improve the performance of BCZT-based ceramics while reducing the sintering temperature, presenting high practical application value in the fields of low electric field sensors and actuators. Full article

An Integrated Process Intensification (IPI) technology-based roadmap is proposed for the utilization of renewables (water, air and biomass/unavoidable waste) in the small-scale distributed production of the following primary products: electricity, H₂, NH₃, HNO₃ and symbiotic advanced (SX) fertilizers with CO₂ mineralization capacity to achieve negative CO₂ emission. Such a production platform is an integrated intensified biorefinery (IIBR), used as an alternative to large-scale centralized production which relies on green electricity and CCUS. Hence, the capacity and availability of the renewable biomass and unavoidable waste were examined. The critical elements of the IIBR include gasification/syngas production; syngas cleaning; electricity generation; and the conversion of clean syngas (which contains H₂, CO, CH₄, CO₂ and N₂) to the primary products using nonthermal plasma catalytic reactors with in situ NH₃ sequestration for SA fertilizers. The status of these critical elements is critically reviewed with regard to their techno-economics and suitability for industrial applications. Using novel gasifiers powered by a combination of CO₂, H₂O and O₂-enhanced air as the oxidant, it is possible to obtain syngas with high H₂ concentration suitable for NH₃ synthesis. Gasifier performances for syngas generation and cleaning, electricity production and emissions are evaluated and compared with gasifiers at 50 kWe and 1–2 MWe scales. The catalyst and plasma catalytic reactor systems for NH₃ production with or without in situ reactive sequestration are considered in detail. The performance of the catalysts in different plasma reactions is widely different. The high intensity power (HIP) processing of perovskite (barium titanate) and unary/binary spinel oxide catalysts (or their combination) performs best in several syntheses, including NH₃ production, NO_x from air and fertigation fertilizers from plasma-activated water. These catalysts can be represented as BaTi_1−vO_3−x{#}_yN_z (black, piezoelectric barium titanate, bp-{BTO}) and M⁽¹⁾_3−jM⁽²⁾_kO_4−m{#}_nN_r/SiO₂ (unary (k = 0) or a binary (k > 0) silane-coated SiO₂-supported spinel oxide catalyst, denoted as M/Si = X) where {#} infers oxygen vacancy. HIP processing in air causes oxygen vacancies, nitrogen substitution, the acquisition of piezoelectric state and porosity and chemical/morphological heterogeneity, all of which make the catalysts highly active. Their morphological evaluation indicates the generation of dust particles (leading to porogenesis), 2D-nano/micro plates and structured ribbons, leading to quantum effects under plasma catalytic synthesis, including the acquisition of high-energy particles from the plasma space to prevent product dissociation as a result of electron impact. M/Si = X (X > 1/2) and bp-{BTO} catalysts generate plasma under microwave irradiation (including pulsed microwave) and hence can be used in a packed bed mode in microwave plasma reactors with plasma on and within the pores of the catalyst. Such reactors are suitable for electric-powered small-scale industrial operations. When combined with the in situ reactive separation of NH₃ in the so-called Multi-Reaction Zone Reactor using NH₃ sequestration agents to create SA fertilizers, the techno-economics of the plasma catalytic synthesis of fertilizers become favorable due to the elimination of product separation costs and the quality of the SA fertilizers which act as an artificial root system. The SA fertilizers provide soil fertility, biodiversity, high yield, efficient water and nutrient use and carbon sequestration through mineralization. They can prevent environmental damage and help plants and crops to adapt to the emerging harsh environmental and climate conditions through the formation of artificial rhizosphere and rhizosheath. The functions of the SA fertilizers should be taken into account when comparing the techno-economics of SA fertilizers with current fertilizers. Full article

In the field of piezoelectric applications, perovskite-based multifunctional composite ceramics are widely explored. The morphotropic phase boundary (MPB) regions, where dual structural phases coexist, play a crucial role in boosting the ferroelectric and piezoelectric properties significantly. Herein, MPB-region-existent 0.7BiFeO₃-0.3BaTiO₃ (BFBT) composite ceramic is investigated under the influence of wt%Sn-ion incorporation at the lattice sites of the BFBT. Specifically, the ceramic composition BFBT:0.2Sn has demonstrated excellent remnant polarization (P_r ~ 22.68 µC/cm²), an impressive piezoelectric coefficient (d₃₃ ~ 211 pC/N), stable impedance of 1.07 × 10⁷ Ω, a Curie temperature of 435 °C and low dielectric loss (tanδ) of <0.5. Moreover, the BFBT:0.2Sn ceramic has also maintained a stable d₃₃ of ~150 pC/N and resistivity of ~10² Ω even at a temperature of 400 °C. Such outcomes confirm the ability and potential of the BFBT:0.2Sn ceramic composition for high-temperature piezoelectric applications. Full article

This paper investigates the synthesis and characterization of eco-friendly piezoelectric composite thin films composed of chitosan and Ln₂O₃-doped Na_0.5Bi_0.5TiO₃-BaTiO₃ (NBT-BT) nanoparticles. The films were fabricated using a solution-casting technique, successfully embedding the particles into the chitosan matrix, which resulted in enhanced piezoelectric properties compared to pure chitosan. Characterization methods, such as photoluminescence spectroscopy and piezo-response force microscopy (PFM) which revealed strong electromechanical responses, with notable improvements in piezoelectric performance due to the inclusion of NBT-BT nanoparticles. X-ray diffraction (XRD) analysis revealed a pure perovskite phase with the space group R3c for NBT-BT and NBT-BT-Ln particles. Scanning electron microscopy (SEM) images showed a non-uniform distribution of NBT-BT particles within the chitosan matrix. The results also suggest that the incorporation of rare earth elements further enhances the electrical and piezoelectric properties of the composites, highlighting their potential in flexible and smart device applications. Overall, these findings underscore the potential of chitosan-based composites in addressing environmental concerns while offering effective solutions for energy harvesting and biomedical applications. Full article

Amidst the swift expansion of the electric vehicle industry, the imperative for alternative battery technologies that balance economic feasibility with sustainability has reached unprecedented importance. Herein, we utilized Perovskite-based oxide compounds barium titanate (BaTiO₃) and strontium titanate (SrTiO₃) nanoparticles as anode materials for lithium-ion batteries from straightforward and standard carbonate-based electrolyte with 10% fluoroethylene carbonate (FEC) additive [1M LiPF₆ (1:1 EC: DEC) + 10% FEC]. SrTiO₃ and BaTiO₃ electrodes can deliver a high specific capacity of 80 mA h g⁻¹ at a safe and low average working potential of ≈0.6 V vs. Li/Li⁺ with excellent high-rate performance with specific capacity of ~90 mA h g⁻¹ at low current density of 20 mA g⁻¹ and specific capacity of ~80 mA h g⁻¹ for over 500 cycles at high current density of 100 mA g⁻¹. Our findings pave the way for the direct utilization of perovskite-type materials as anode materials in Li-ion batteries due to their promising potential for Li⁺ ion storage. This investigation addresses the escalating market demands in a sustainable manner and opens avenues for the investigation of diverse perovskite oxides as advanced anodes for next-generation metal-ion batteries. Full article

Ba_0.75Ca_0.25TiO₃ ceramics were successfully synthesized by a simple solid-state reaction method. This study examined the influence of sintering temperature on the structure, microstructure, dielectric properties and electrical behavior of the material. The XRD analysis reveals that the tetragonal phase (P4mm) is dominant in all the synthesized materials, with those sintered at T = 1400 °C and T = 1450 °C being single-phase, while others exhibit a minor orthorhombic phase (Pbnm). Higher sintering temperatures promoted better grain boundary formation and larger grain sizes. The electric permittivity increased with temperature up to T = 1400 °C, followed by a sharp decline at T = 1450 °C. Additionally, the Curie temperature decreased with increasing sintering temperature, indicating changes in phase transition characteristics. Thermal analysis showed that higher sintering temperatures led to sharper heat capacity peaks, while pyroelectric and thermally stimulated depolarization currents were maximized at T = 1400 °C due to oxygen vacancies. These findings highlight the significant impact of sintering temperature on the material’s structural and functional properties. Full article

A bottleneck characterized by high strain and low hysteresis has constantly existed in the design process of piezoelectric actuators. In order to solve the problem that actuator materials cannot simultaneously exhibit large strain and low hysteresis under relatively high electric fields, Nb⁵⁺-doped 0.975(Ba_0.85Ca_0.15)[(Zr_0.1Ti_0.9)_0.999Nb_0.001]O₃-0.025(Bi_0.5Na_0.5)ZrO₃ (BCZTNb_0.001-0.025BiNZ) ceramic thick films were prepared by a film scraping process combined with a solid-state twin crystal method, and the influence of sintering temperature was studied systematically. All BCZTNb_0.001-0.025BiNZ ceramic thick films sintered at different sintering temperatures have a pure perovskite structure with multiphase coexistence, dense microstructure and typical dielectric relaxation behavior. The conduction mechanism of all samples at high temperatures is dominated by oxygen vacancies confirmed by linear fitting using the Arrhenius law. As the sintering temperature elevates, the grain size increases, inducing the improvement of dielectric, ferroelectric and field-induced strain performance. The 1325 °C sintered BCZTNb_0.001-0.025BiNZ ceramic thick film has the lowest hysteresis (1.34%) and relatively large unipolar strain (0.104%) at 60 kV/cm, showing relatively large strain and nearly zero strain hysteresis compared with most previously reported lead-free piezoelectric ceramics and presenting favorable application prospects in the actuator field. Full article

To meet the current demand for lead-free piezoelectric ceramics, a novel sol-gel synthesis route is presented for the preparation of Ba_0.85Ca_0.15Ti_0.9Zr_0.1O₃ doped with cerium (Ce = 0, 0.01, and 0.02 mol%) and vanadium (V = 0, 0.3, and 0.4 mol%). X-ray diffraction patterns reveal the formation of a perovskite phase (space group P4mm) for all samples after calcination at 800 °C and sintering at 1250, 1350, and 1450 °C, where it is proposed that both dopants occupy the B site. Sintering studies show that V doping allows the sintering temperature to be reduced to at least 1250 °C. Undoped BCZT samples sintered at the same temperature show reduced functional properties compared to V-doped samples, i.e., d₃₃ values increase by an order of magnitude with doping. The dissipation factor tan δ decreases with increasing sintering temperature for all doping concentrations, while the Curie temperature T_C increases for all V-doped samples, reaching 120 °C for high-concentration co-doped samples. All results indicate that vanadium doping can facilitate the processing of BCZT at lower sintering temperatures without compromising performance while promoting thermal property stability. Full article

BaTiO₃-Bi(Zn,Ti)O₃ (BT-BZT) ceramics have been used as capacitors due to their large dielectric permittivity and excellent temperature stability and are good candidates for lead-free materials for electrocaloric and energy storage devices. However, BT-BZT ceramics often suffer from inferior properties and poor reproducibility due to heterogeneous compositional distribution after calcination and sintering. In this work, (1−x)BT-xBZT ceramics (x = 0~0.2) were fabricated with nano-sized BaTiO₃ raw materials (nano-BT) by a solid-state reaction method to enhance the chemical homogeneity. The (1−x)BT-xBZT ceramics prepared from the nano-BT showed larger densities and more uniform microstructures at the lower calcination and sintering temperatures than the samples prepared from more frequently used micrometer-sized raw materials BaCO₃, TiO₂, Bi₂O₃, and ZnO. The (1−x)BT-xBZT ceramic prepared from the nano-BT displayed a phase transition from a tetragonal ferroelectric to a pseudo-cubic relaxor in a narrower composition range than the sample prepared from micro-sized raw materials. Larger adiabatic temperature changes due to the electro-caloric effect (ΔT_ECE) and recoverable energy storage density (U_rec) were observed in the samples prepared from the nano-BT due to the higher breakdown electric fields, the larger densities, and uniform microstructures. The 0.95BT-0.05BZT sample showed the largest ΔTECE of 1.59 K at 80 °C under an electric field of 16 kV/mm. The 0.82BT-0.18BZT sample displayed a U_rec of 1.45 J/cm², which is much larger than the previously reported value of 0.81 J/cm² in BT-BZT ceramics. The nano-BT starting material produced homogeneous BT-BZT ceramics with enhanced ECE and energy storage properties and is expected to manufacture other homogeneous solid solutions of BaTiO₃ and Bi-based perovskite with high performance. Full article

In the present work, we investigate the potential of modified barium titanate (BaTiO₃), an inexpensive perovskite oxide derived from earth-abundant precursors, for developing efficient water oxidation electrocatalysts using first-principles calculations. Based on our calculations, Rh doping is a way of making BaTiO₃ absorb more light and have less overpotential needed for water to oxidize. It has been shown that a TiO₂-terminated BaTiO₃ (001) surface is more promising from the point of view of its use as a catalyst. Rh doping expands the spectrum of absorbed light to the entire visible range. The aqueous environment significantly affects the ability of Rh-doped BaTiO₃ to absorb solar radiation. After Ti→Rh replacement, the doping ion can take over part of the electron density from neighboring oxygen ions. As a result, during the water oxidation reaction, rhodium ions can be in an intermediate oxidation state between 3+ and 4+. This affects the adsorption energy of reaction intermediates on the catalyst’s surface, reducing the overpotential value. Full article

Given the increasingly severe environmental problems caused by water pollution, the degradation of organic dyes can be effectively achieved through the utilization of photocatalysis. In this work, metal alkoxides and a combination of alcohol/hydrophobic solvents are employed to prepare BaTiO₃ aerogels via a liquid-phase and template-free synthetic route. The preparation process of the aerogels solely entails facile agitation and supercritical drying, eliminating the need for additional heat treatment. The binary solvent of ethanol and toluene is identified as the optimal choice, resulting in a significantly enhanced surface area (up to 223 m²/g) and an abundant pore structure of BaTiO₃ aerogels compared to that of the BaTiO₃ nanoparticles. Thus, the removal efficiency of the BaTiO₃ aerogel sample for MO is nearly twice as high as that of the BaTiO₃ nanoparticles sample. Noble metal Ag nanoparticles’ deposition onto the BaTiO₃ aerogel surface is further achieved via the photochemical deposition method, which enhances the capture of photogenerated electrons, thereby ensuring an elevated level of photocatalytic efficiency. As a result, Ag nanoparticles deposited on BaTiO₃ aerogel can degrade MO completely after 40 min of illumination, while the corresponding aerogel before modification can only remove 80% of MO after 60 min. The present work not only complements the preparatory investigation of intricate aerogels but also offers a fresh perspective for the development of diverse perovskite aerogels with broad applications. Full article

In cation–anion co-doping, rare earth elements excel at regulating the electronic structure of perovskites, leading to their improved photocatalytic performance. In this regard, the impact of co-doping rare earth elements at the Ba and Ti sites in BaTiO₃ on its electronic and photocatalytic properties was thoroughly investigated based on 2 × 2 × 2 supercell structures of BaTiO₃ with different La concentrations of 12.5% and 25% using DFT calculations. The band structure, density of states, charge density difference, optical properties, and the redox band edge of the co-doped models mentioned above were analyzed. The results indicated that the BaTiO₃ structure co-doped with 25% La at the Ti site exhibited higher absorption in the visible range and displayed a remarkable photocatalytic water-splitting performance. The introduced La dopant at the Ti site effectively reduced the energy required for electronic transitions by introducing intermediate energy levels within the bandgap. Our calculations and findings of this study provide theoretical support and reliable predictions for the exploration of BaTiO₃ perovskites with superior photocatalytic performances. Full article