Search Results (8)

Low temperature combustion (LTC) mitigates the nitrogen oxide (NO_x) and particulate matter (PM) trade-off in conventional compression ignition engines. Significant research on LTC using partially premixed charge compression ignition (PPCI) has typically reduced the compression ratio of the engine to control combustion phasing and lower peak temperatures. This study investigates LTC using PPCI with a high-compression-ratio (=21.2) engine by varying fuel injection timing (FIT) from 12.5° to 30.0° before top dead center (BTDC) while modulating EGR (0%, 7%, 14%, and 25%). Advancing FIT led to a gradual rise in the equivalence ratio of the mixture, in-cylinder pressure, temperature, and rate of heat release due to energy losses associated with ignition occurring before the end of the compression stroke. PPCI was successfully achieved with minimal performance impact using a combination of FIT advancements in the presence of high rates of EGR. Specifically, fuel injected at 25.0° BTDC and 25% EGR reduced PM emissions by 59% and total hydrocarbons by 25% compared with conventional FIT (12.5°) without EGR. Moreover, carbon monoxide and NO_x emissions were comparable across set points. As a result, PPCI using high compression ratios is possible and can lead to greater thermal efficiencies while reducing emissions. Full article

Gasoline engines employing the spatially distributed auto-ignition combustion mode, known as controlled auto-ignition (CAI), are a prospective technology for significantly improving engine efficiency and reducing emissions. This review paper provides an overview of developments in various gasoline CAI technologies and discusses their attendant strengths and weaknesses. Hybrid propulsion systems powered by high-efficiency gasoline CAI engines can provide a low-carbon pathway for mobility sector decarbonisation. Therefore, this paper focuses on the challenges and opportunities of CAI implementation, especially for electrified powertrains. Different control actuators that can extend the CAI operating range are discussed, and opportunities for synergistic operation between thermal and electric components of hybridised powertrains are identified. Such synergies can remove impediments in the way of CAI system adoption and can, thus, support CAI adoption and maximise efficiency gains from its implementation. The prospects of supporting CAI combustion for different powertrain electrification levels, hybrid architectures, engine size, and energy management systems are discussed. Load levelling offered by electrified powertrains through CAI-favouring energy management strategies has the potential to substantially relax the operating point requirements for CAI-based thermal propulsion units and to remove the need for expensive actuators. The highly flexible spark-assisted partially premixed compression ignition hybrid mode (SACI-PPCI) emerges as a promising CAI strategy for conventional powertrains, and the moderately flexible spark-assisted compression ignition (SACI) configuration can be a cost-effective thermal propulsion mode for electrified powertrains. Full article

The global automotive industry is undergoing a significant transition as battery electric vehicles enter the market and diesel sales decline. It is widely recognized that internal combustion engines (ICE) will be needed for transport for years to come; however, demands on ICE fuel efficiency, emissions, cost, and performance are extremely challenging. Gasoline compression ignition (GCI) is one approach for achieving the demanding efficiency and emissions targets. A key technology enabler for GCI is partially-premixed, compression ignition (PPCI) combustion, which involves two high-pressure, late fuel injections during the compression stroke. Both NOx and smoke emissions are greatly reduced relative to diesel, and this reduces the aftertreatment (AT) requirements significantly. For robust low-load and cold operation, a two-step valvetrain system is used for exhaust rebreathing (RB). Exhaust rebreathing involves the reinduction of hot exhaust gases into the cylinder during a second exhaust lift event during the intake stroke to help promote autoignition. The amount of exhaust rebreathing is controlled by exhaust backpressure, created by the vanes on the variable nozzle turbine (VNT) turbocharger. Because of the higher cycle temperatures during rebreathing, exhaust HC and CO may be significantly reduced, while combustion robustness and stability also improve. Importantly, exhaust rebreathing significantly increases exhaust temperatures in order to maintain active catalysis in the AT system for ultra-low tailpipe emissions. To achieve these benefits, it is important to optimize the rebreathe valve lift profile and develop an RB ON→OFF (mode switch) strategy that is easy to implement and control, without engine torque fluctuation. In this study, an engine model was developed using GT-Suite to conduct steady-state and transient engine simulations of the rebreathing process, followed by engine tests. The investigation was conducted in four parts. In part 1, various rebreathe lift profiles were simulated. The system performance was evaluated based on in-cylinder temperature, exhaust temperature, and pumping work. The results were compared with alternative variable valve actuation (VVA) strategies such as early exhaust valve closing (EEVC), negative valve overlap (NVO), positive valve overlap (PVO). In part 2, steady-state simulations were conducted to determine an appropriate engine load range for mode switching (exhaust rebreathing ON/OFF and vice-versa). The limits for both in-cylinder temperature and exhaust gas temperature, as well as the external exhaust gas recirculation (EGR) delivery potential were set as the criteria for load selection. In part 3, transient simulations were conducted to evaluate various mode switch strategies. For RB OFF, the cooled external EGR was utilized with the goal to maintain exhaust gas dilution during mode switches for low NOx emissions. The most promising mode-switch strategies produced negligible torque fluctuation during the mode switch. Finally, in part 4, engine tests were conducted, using the developed RB valve lift profile, at various low-load operating conditions. The mode switch experiments correlated well with the simulation results. The tests demonstrated the simplicity and robustness of the exhaust rebreathing approach. A robust engine response, low CNL, high exhaust gas temperature, and low engine out emissions were achieved in the low load region. Full article

Natural gas (NG) engines have very broad application prospects. The pilot-ignited NG diesel engine can be organized into two combustion modes according to the sequence of oil and gas injection: (1) High-pressure direct injection, where NG is mainly diffused combustion; and (2) partially premixed compression ignition, where NG is mainly premixed combustion. In this study, we used CONVERGE to explore the influence of the NG injection timing on the distribution of the mixture equivalence ratio, ignition characteristics, thermal efficiency, emission, and combustion reaction rate under the two combustion modes. We also used a multi-step soot model to analyze the particle mass and quantity. We showed herein that the NG injection timing significantly affects the mixture distribution in the cylinder, thereby consequently affecting the combustion process. Both very early and very late injection times were not conducive to NG combustion. In addition, the mass, quantity, and diameter of the soot produced by diffusion combustion were larger than those produced with premixed combustion. Full article

An improved heating and evaporation model of fuel droplets is implemented into the commercial Computational Fluid Dynamics (CFD) software CONVERGE for the simulation of sprays. The analytical solutions to the heat conduction and species diffusion equations in the liquid phase for each time step are coded via user-defined functions (UDF) into the software. The customized version of CONVERGE is validated against measurements for a single droplet of n-heptane and n-decane mixture. It is shown that the new heating and evaporation model better agrees with the experimental data than those predicted by the built-in heating and evaporation model, which does not consider the effects of temperature gradient and assumes infinitely fast species diffusion inside droplets. The simulation of a hollow-cone spray of primary reference fuel (PRF65) is performed and validated against experimental data taken from the literature. Finally, the newly implemented model is tested by running full-cycle engine simulations, representing partially premixed compression ignition (PPCI) using PRF65 as the fuel. These simulations are successfully performed for two start of injection timings, 20 and 25 crank angle (CA) before top-dead-centre (BTDC). The results show good agreement with experimental data where the effect of heating and evaporation of droplets on combustion phasing is investigated. The results highlight the importance of the accurate modelling of physical processes during droplet heating and evaporation for the prediction of the PPCI engine performance. Full article

The direct injection of natural gas (NG), which is an important research direction in the development of NG engines, has the potential to improve thermal efficiency and emissions. When NG engines operate in low-load conditions, combustion efficiency decreases and hydrocarbon (HC) emissions increase due to lean fuel mixtures and slow flame propagation speeds. The effect of two combustion modes (partially premixed compression ignition (PPCI) and high pressure direct injection (HPDI)) on combustion processes was investigated by CFD (Computational Fluid Dynamics), with a focus on different injection strategies. In the PPCI combustion mode, NG was injected early in the compression stroke and premixed with air, and then the pilot diesel was injected to cause ignition near the top dead center. This combustion mode produced a faster heat release rate, but the HC emissions were higher, and the combustion efficiency was lower. In the HPDI combustion mode, the diesel was injected first and ignited, and then the NG was injected into the flame. This combustion mode resulted in higher emissions of NO_x and soot, with a diffusion combustion in the cylinder. HC emissions significantly decreased. Compared with PPCI combustion, HPDI had a higher thermal efficiency. Full article

A study on unregulated emissions of a conventional diesel self-ignition and partial premixed compression ignition (PPCI) marine engine at full load condition was performed, respectively. In this work, PPCI was realized in a marine engine by blending 15% diesel with 85% light hydrocarbons (LHC). Gas chromatography-mass spectrometry (GC-MS) was used to detect and identify unregulated emissions, and the chemical formula and peak area of representative species were obtained. Furthermore, the unregulated emissions were classified and semi-quantitatively analyzed. The results show that the maximum in-cylinder pressure of PPCI is almost 11 bar lower than that of conventional diesel combustion, and the crank angle at that moment is also delayed by 2 °CA. Compared to conventional diesel combustion, the maximum pressure rise rate of PPCI is reduced by 3.5%, while the maximum heat release rate of PPCI increases by 23.5%. Further, PPCI produces fewer species in unregulated emissions, and their chemical formula are less complex than that of conventional diesel combustion. Compared to conventional diesel combustion, the relative concentration of alkane and organic components in PPCI decreases significantly, while ketone and ester increase. Full article

Pilot injection combined with exhaust gas recirculation (EGR) is usually utilized to realize the partially premixed compression ignition (PPCI) mode in diesel engines, which enables the simultaneous decrease of nitrogen oxide and soot emissions to satisfy emission regulations. Moreover, the ignition delay of main injection combustion can also be shortened by pilot injection, and then combustion noise is reduced. Nevertheless, the mechanisms of pilot injection impacts on combustion noise are not completely understood. As such, it is hard to optimize pilot injection parameters to minimize combustion noise. Therefore, experiments were conducted on a four-stroke single-cylinder diesel engine with different pilot injection strategies and 20% EGR as part of an investigation into this relationship. Firstly, the combustion noise was analyzed by cylinder pressure levels (CPLs). Then, the stationary wavelet transforms (SWTs) and stationary wavelet packet transform (SWPT) were employed to decompose in-cylinder pressures at different scales, and thus the combustion noise generated by pilot and main combustion was investigated in both the time and frequency domain. The results show that pilot injection is dominant in the high frequency segment of combustion noise, and main injection has a major impact on combustion noise in the low and mid frequency segment. Finally, the effects of various pilot injection parameters on suppressing combustion noise were analyzed in detail. Full article