Search Results (14)

This work investigates the influence of crystallinity on the mechanical properties of needle-punched non-woven flax/polylactic acid (PLA) biocomposites with different flax fiber contents. Biocomposites were fabricated by a compression molding adopting different cooling rates to understand the mechanism of crystallinity and their contribution to the mechanical properties. Image-based analysis of the fiber distribution in non-woven preform indicates the probable origins of the residual porosities and the potential nucleation sites for crystal formation within the composites. The improvement of 25% and 100% in flexural modulus is observed for the composites with 40% and 50% of flax fiber mass fractions, respectively, when subjected to a lower cooling rate, which implies the significant influence of the void content on the brittleness of composites. The impact properties of the composites decrease from 11% to 18% according to the flax fiber mass fraction when the cooling rate decreases to 1 °C/min, and the composites become more brittle. The induced impact and flexural properties of the composites are compared with those of other composites in the literature to emphasize their applicability to semi-structural applications. Full article

Introduction: Comparative studies on Hounsfield units (HU) and bone volume fraction (BVF%) for the demonstration of cancellous bone density in the entire spine and in the various intravertebral regions are rare. The aim of the present study was to determine HU in various segments and sectional planes (sagittal, axial, coronary) of the spine and their description in the context of bone density measurement on micro-CT, as well as the significance of the values for bone loss and fracture risk. Materials/Methods: The spines of 11 body donors were analyzed by means of high-resolution spiral CT and micro-CT. Vertebral deformities were identified on sagittal reformations and classified. Cancellous bone density in the individual vertebrae from C3 to L5, expressed in HU, was measured on CT images (in all 242 vertebral bodies). For this purpose, a manually positioned ROI was established in mid-vertebral cancellous bone in the axial, sagittal, and coronary planes. Using a Jamshidi^® needle, we obtained 726 specimens from prepared vertebrae extracted from three quadrants (QI: right-sided edge, QII: central, QIII: left-sided edge) and analyzed these on a micro-CT device (SKYSCAN 1172, RJL Micro & Analytic GmbH, Germany). The study design with multiple measurements was reflected by a General Linear Model Repeated Measures. The model was adjusted to the bone density values of both procedures (HU, BVF%) in the viewed sectional planes and quadrants for 22 vertebrae, with the predictors gender and fracture status, controlled for age and body mass index (BMI). Analysis of variance provided estimations of density values and comparisons of several subgroups. Results: All spines were osteoporotic. Both procedures revealed a significant reduction in cancellous bone density from C3 to L5 (p ≤ 0.018). Gender (p = 0.002) and fracture status (p = 0.001) have an impact on bone density: men have higher bone density values than women; cases with fewer fractures also have higher bone density values. CT revealed both effects (p = 0.002 for each) with greater clarity. HU on CT measurements in the axial plane showed higher density values than in the sagittal or coronary planes. CT measurement profiles along the spine as well as along the individual profiles of the 11 body donors were independent of the measured quadrants, but the micro-CT measurements were not. Discussion: The craniocaudal reduction in bone density was demonstrated in different degrees of clarity by the two procedures. Likewise, the procedure-related visualization of differences in cancellous bone density between genders, fracture groups, sectional planes, and quadrants indicates the need for a better understanding of the advantages of each procedure for patient-oriented approaches to the diagnosis of osteoporosis. Future research should be focused on the determination of standard values and their clinical application for the prevention and treatment of osteoporosis. Full article

Background and clinical significance: Phyllodes tumors (PTs) are rare stromal neoplasms originating in the connective tissue of the breast, distinct from carcinomas that arise from the ducts or lobules. These tumors exhibit a broad spectrum of morphologic features and are traditionally classified as benign, borderline, or malignant. Case presentation: We present the case of a 71-year-old female diagnosed with a malignant PT and treated at our hospital. The patient noticed a gradually enlarging lump in her right breast over several months. Mammography was inconclusive, but an ultrasound later revealed a lobulated, firm mass, classified as BIRADS 5. Physical examination identified a 20 cm mass, and core needle biopsy suggested a borderline PT. Following lumpectomy, pathology confirmed a malignant tumor with narrow surgical margins (0.1 cm). Although mastectomy was recommended to achieve wider margins, the patient opted for adjuvant radiotherapy. She received 50 Gy in 25 fractions to the whole breast, followed by a 16 Gy boost to the tumor bed in 8 fractions. The treatment was well tolerated and completed successfully. Initially, the patient’s therapeutic management was delayed due to a combination of personal and organizational factors. However, the process was later streamlined through the use of a novel digital tool developed to facilitate the entire patient journey within our hospital system. Conclusions: This case highlights the diagnostic complexities of PTs, the critical need for effective collaboration between specialties, and the importance of timely treatment planning for optimal patient outcomes. Full article

Understanding needle biomass turnover rates in Scots pine (Pinus sylvestris L.) stands is crucial for modelling forest ecosystem dynamics and nutrient cycling. This study examined needle litterfall and biomass turnover in Scots pine stands of varying ages in temperate forests (western Poland). The research focused on determining how stand age affects needle biomass, litterfall and the associated turnover rates. Data were collected from 20 Scots pine stands aged 26 to 90 years, and needle litterfall was measured and analysed in relation to stand characteristics such as age, density and biomass. The average annual needle litter production of the sampled Scots pine stands was 2008 kg·ha⁻¹·year⁻¹, similar to the values previously reported for this tree species in other temperate forests in Europe. The average needle biomass turnover rate for sampled Scots pine stands was 23.4%. We could not support the hypothesis that this parameter depended on the age of the Scots pine stand. The needle biomass turnover rate showed a positive correlation with crown length and a negative correlation with stand density due to the very weak correlations; however, further research is needed to confirm these relationships. Despite this, the parameter can be used to estimate needle litterfall and can be applicable to conditions corresponding to those of temperate forests in Central and Western Europe. This study also highlights the need for further research on needle biomass turnover in temperate forests to improve the accuracy of carbon and nutrient cycling models. This work contributes to a deeper understanding of the role of needle litterfall in maintaining soil fertility and forest productivity, offering insights into sustainable forest management and conservation strategies. Full article

This study investigates the nanostructural properties of pseudo-binary Al–1.0Mg₂Si (mass%) alloys with and without 0.5Cu using transmission electron microscopy (TEM) and small-angle neutron scattering (SANS). The TEM results show that both alloys exhibit extra electron diffraction spots related to MgSiMg second clusters at peak-aged conditions. High-resolution TEM images have revealed that the second cluster exists as a needle-shaped precipitate that is shorter and thicker than the β″ phase. We found that the second cluster, which we referred to as the R phase in this paper, is more likely to form partially along the longitudinal axis of a random-type precipitate. Thus, the atomic arrangement in the random-type precipitate is not completely random. SANS is used to quantify the size and volume fraction of the observed needle-shaped precipitates since the R phase is difficult to observe with TEM. The R phase forms even in the Cu-free alloy, but the volume fraction is low, and the growth and formation are retarded near the peak-aged conditions. Undoubtedly, the Cu addition has the effect of stabilizing the growth of the R phase and also promoting its formation. Therefore, the R phase also contributes to the increase in hardness at both under- and peak-aged conditions in the Cu-containing alloy in addition to the strengthening β″ phases. Full article

The composite gelling system of chlorine and magnesium thioxide was prepared by mixing different mass fractions of magnesium sulfate solution into MOC. Detailed studies regarding the influences of magnesium sulfate replacing magnesium chloride on the setting time, compressive strength, and water resistance of magnesium oxychloride cement (MOC) have been carried out in this paper. The phase composition and micro morphology of the hydration products in the mixed system were analyzed by XRD and SEM. The results show that the addition of magnesium sulfate prolongs the setting time and reduces the compressive strength of the mixed MOC. Compared with the primordial MOC system, the water resistance of the mixed system improved, with the mixed system exhibiting optimal water resistance when the mass fraction of magnesium sulfate was 30%. The phases of the mixed system were composed of 5Mg(OH)₂·MgCl₂·8H₂O and 5Mg(OH)₂·MgSO₄·7H₂O phases. The microscopic morphology shows that the interior of air-cured MOC was composed of a large number of needle-like crystals, and continuous crystal structures have close contact and a strong bonding force. Cracks and pores appear on the surface after submerging in water, and the crystallization state of the internal crystals becomes worse. The compressive strength and water stability of MOC were closely related to the crystal morphology. Full article

The specific branches of industry utilize needle coke, a carbon form with a highly anisotropic structure. Searching for novel raw materials for its production is now rigorously studied. In the present work, we use low-sulfur gasoil for this purpose, namely its high-boiling fractions. We study their chemical and physicochemical parameters with the set of physicochemical and spectral methods. The data of FT-IR and UV-Vis spectroscopies with a phenomenological method (that allows assessing average electronic structure parameters) indicate that the gas oil of the West Siberian origin contains polycyclic aromatic hydrocarbons (PAHs) with 3–5 condensed benzene rings. The maximum amount of PAHs with molecular masses of 400–600 a.u. is contained in the fractions with boiling points higher than 450 °C. According to the data of polarized-light optical microscopy, the higher boiling point of the gasoil fraction the higher anisotropy of the produced coke. This occurs as a result of an increase in the amount of PAHs capable of condensation with the formation of a mesophase. Thus, low-sulfur gas oils from thermally processed West Siberian oil are promising raw materials for the production of needle coke in delayed coking processes. Full article

Transformation of aragonite, a mineral phase metastable at Earth’s surface, to calcite widely occurs in both sedimentary and metamorphic systems with the presence of an aqueous phase. The transformation process can affect geochemical signatures of aragonite (a protolith). This study focused on quantification of the retention of Mg/Ca and Sr/Ca ratios, and δ¹⁸O during the transformation process as well as evaluation of the transformation rate. To investigate the effect of transformation from aragonite to calcite on elemental and stable isotope ratios, we conducted a series of experiments in NaCl solutions at temperatures between 120 and 184 °C. Two additional experiments at 250 °C were conducted to estimate the transformation rate of aragonite to calcite. Protolith materials consist of (1) synthetic (Mg; Sr-bearing or non-Mg; Sr bearing) needle-shaped microcrystals of aragonite (<5 µm in size) and (2) larger chips (>100 µm in size) of natural aragonite. X-ray diffraction (XRD) showed that microcrystals successfully transformed to calcite within 30 h and scanning electron microscopy (SEM) yielded a change in the crystal size to >10 µm in rhombohedral shape. Electron backscatter diffraction (EBSD) of the larger aragonite chips showed that transformation to randomly oriented calcite occurred at the rims and along the cracks while the core retained an aragonite crystal structure. Isotope-ratio mass spectrometry (IRMS) analyses showed that calcite δ¹⁸O was controlled by temperature and δ¹⁸O of the solution. The obtained calibration curve of isotope fractionation factor versus temperature is consistent with other studies. Inductively coupled plasma optical emission spectroscopy (ICP-OES) analyses showed that calcite partially or completely retained Mg/Ca and Sr/Ca ratios through the transformation. Full article

The present work describes the use of Centrifugal Partition Chromatography (CPC) for the bio-guided isolation of repellent active volatile compounds from essential oils. Five essential oils (EOs) obtained from three Pinus and two Juniperus species were initially analyzed by gas chromatography–mass spectrometry (GC/MS) and evaluated for their repellent properties against Aedes albopictus. The essential oil from needles of P. pinea (PPI) presented the higher activity, showing 82.4% repellency at a dose of 0.2 μL/cm². The above EO, together with the EO from the fruits of J. oxycedrus subsp. deltoides (JOX), were further analyzed by CPC using the biphasic system n-Heptane/ACN/BuOH in ratio 1.6/1.6/0.2 (v/v/v). The analysis of PPI essential oil resulted in the recovery of (−)-limonene, guaiol and simple mixtures of (−)-limonene/β-pheladrene, while the fractionation of JOX EO led to the recovery of β-myrcene, germacrene-D, and mixtures of α-pinene/β-pinene (ratio 70/30) and α-pinene/germacrene D (ratio 65/45). All isolated compounds and recovered mixtures were tested for their repellent activity. From them, (−)-limonene, guaiol, germacrene-D as well the mixtures of (−)-limonene/β-pheladrene presented significant repellent activity (>97% repellency) against Ae. albopictus. The present methodology could be a valuable tool in the effort to develop potent mosquito repellents which are environmentally friendly. Full article

Great variation in shape and size between primary (juvenile) and secondary (adult) needles, so-called leaf-heteroblasty, occurs in several Pinus species. Most of them loss primary needles during the juvenile-to-adult transition of the tree. An exception to this is Pinus canariensis (a Canary Islands endemism) in which basal resprouting twigs of adult trees frequently wear both primary and secondary needles. Taking advantage of this extraordinary study-case-species, we conducted an exhaustive comparison of both needle types through quantitative analyses of needle anatomy, photochemical performance, gas exchange, and resistance to extreme dehydration and to extreme needle temperature. We hypothesized that primary needles would show lower investment to leaf structure but higher photosynthetical efficiency. Primary needles had less stomatal density and thicker and less wettable cuticles. In cross section, primary needles showed smaller structural fraction (e.g., percent of hypodermis, endodermis and vascular tissue) and higher fraction of photosynthetic parenchyma. Significant differences between primary and secondary needles were not found in net carbon assimilation not in their leaf mass area values. Interestingly, secondary needles showed higher electron transport rate, and they were additionally much more efficient in retaining water under severe and controlled desiccant conditions. When subjected to extreme temperatures (−10° to +50 °C), primary needles recovered better their photochemical efficiency than secondary needles, after +46° and +48 °C heat-shock treatments. Our results indicate that both needle types broaden the diversity of physiological responses against environmental constrains in basal twigs of adult P. canariensis trees. Considering that this is a fire-resistant and resprouting species, this advantage could be particularly useful after a drastic environmental change such a fire or a gap opening in the forest. Full article

Scheelite (CaWO₄) and powellite (CaMoO₄) are isostructural minerals considered as a non-ideal solid solution series. Micron- to nanoscale investigation of a specimen of skarnoid from Zhibula, Gangdese Belt, Tibet, China, was carried out to assess the identity of the phases within a broad scheelite-powellite (Sch-Pow) compositional range, and to place additional constraints on redox changes during ore formation. An electron probe microanalysis shows that Mo-rich domains within complex oscillatory-zoned single crystals, and as thin sliver-like domains, have a compositional range from 20 mol.% to 80 mol.% Pow. These occur within a matrix of unzoned, close-to-end-member scheelite aggregates (87 mol.%–95 mol.% Sch). Laser-ablation inductively coupled plasma mass spectrometry spot analysis and element mapping reveal systematic partitioning behaviour of trace elements in skarn minerals (grossular₅₀, diopside₈₀, anorthite, and retrograde clinozoisite) and scheelite-powellite aggregates. The Mo-rich domains feature higher concentrations of As, Nb, and light rare earth elements LREE, whereas W-rich domains are comparatively enriched in Y and Sr. Transmission electron microscopy (TEM) was carried out on focused-ion-beam-prepared foils extracted in situ from domains with oscillatory zoning occurring as slivers of 20 mol.%–40 mol.% Pow and 48 mol.%–80 mol.% Pow composition within an unzoned low-Mo matrix (20 mol.% Pow). Electron diffractions, high-angular annular dark field (HAADF) scanning-TEM (STEM) imaging, and energy-dispersive spectroscopy STEM mapping show chemical oscillatory zoning with interfaces that have continuity in crystal orientation throughout each defined structure, zoned grain or sliver. Non-linear thermodynamics likely govern the patterning and presence of compositionally and texturally distinct domains, in agreement with a non-ideal solid solution. We show that the sharpest compositional contrasts are also recognisable by variation in growth direction. Atomic-scale resolution imaging and STEM simulation confirm the presence of scheelite-powellite within the analysed range (20 mol.%–80 mol.% Pow). Xenotime-(Y) inclusions occur as nm-wide needles with epitaxial orientation to the host scheelite-powellite matrix throughout both types of patterns, but no discrete Mo- or W-bearing inclusions are observed. The observed geochemical and petrographic features can be reconciled with a redox model involving prograde deposition of a scheelite+molybdenite assemblage (reduced), followed by interaction with low-T fluids, leading to molybdenite dissolution and reprecipitation of Mo as powellite-rich domains (retrograde stage, oxidised). The observation of nanoscale inclusions of xenotime-(Y) within scheelite carries implications for the meaningful interpretation of petrogenesis based on rare earth element (REE) concentrations and fractionation patterns. This research demonstrates that HAADF-STEM is a versatile technique to address issues of solid solution and compositional heterogeneity. Full article

Pinus morrisonicola Hayata, usually called Taiwan five-leaf pine (5LP), is an endemic species in Taiwan and is traditionally used to relieve hypertension symptoms and improve cardiovascular function. In this study, the needle extract of 5LP was fractionated and analyzed by LC/MS/MS to search for possible antihypertensive candidates. In addition, bioassay-guided purification of the bioactive components was performed by Ca²⁺ fluorescent signal (Fluo 4-AM) assays. Two dihydrobenzofuran lignans, pinumorrisonide A (1) and icariside E4 (2), and one acylated flavonoid glycoside, kaempferol 3-O-α-(6‴-p-coumaroylglucosyl-β-1,4-rhamnoside) (3) were characterized from the active fractions. The structure of a new compound 1 was established on the basis of 2D NMR spectroscopic and mass spectrometric analyses, and the known compounds 2 and 3 were identified by comparison of their physical and spectroscopic data with those reported in the literature. The purified compounds 1–3 exhibited significant inhibition of Ca²⁺ fluorescence with IC₅₀ values of 0.71, 0.36, and 0.20 mM, respectively. A mechanism study showed that these compounds showed vasorelaxant effects by blocking the voltage-operated Ca²⁺ channel (VOCC) and inhibiting Ca²⁺ influx to the cytoplasmic. These results suggested that 5LP and the three characterized components could be promising antihypertensive candidates for the use as VOCC blockers. Full article

Superhydrophobic surface, as a promising micro/nano material, has tremendous applications in biological and artificial investigations. The electrohydrodynamics (EHD) technique is a versatile and effective method for fabricating micro- to nanoscale fibers and particles from a variety of materials. A combination of critical parameters, such as mass fraction, ratio of N, N-Dimethylformamide (DMF) to Tetrahydrofuran (THF), inner diameter of needle, feed rate, receiving distance, applied voltage as well as temperature, during electrospinning process, to determine the morphology of the electrospun membranes, which in turn determines the superhydrophobic property of the membrane. In this study, we applied a recently developed feedback system control (FSC) scheme for rapid identification of the optimal combination of these controllable parameters to fabricate superhydrophobic surface by one-step electrospinning method without any further modification. Within five rounds of experiments by testing totally forty-six data points, FSC scheme successfully identified an optimal parameter combination that generated electrospun membranes with a static water contact angle of 160 degrees or larger. Scanning electron microscope (SEM) imaging indicates that the FSC optimized surface attains unique morphology. The optimized setup introduced here therefore serves as a one-step, straightforward, and economic approach to fabricate superhydrophobic surface with electrospinning approach. Full article

Hyperspectral remote sensing serves as an effective tool for estimating foliar nitrogen using a variety of techniques. Vegetation indices (VIs) are a simple means of retrieving foliar nitrogen. Despite their popularity, few studies have been conducted to examine the utility of VIs for mapping canopy foliar nitrogen in a mixed forest context. In this study, we assessed the performance of 32 vegetation indices derived from HySpex airborne hyperspectral images for estimating canopy mass-based foliar nitrogen concentration (%N) in the Bavarian Forest National Park. The partial least squares regression (PLSR) was performed for comparison. These vegetation indices were classified into three categories that are mostly correlated to nitrogen, chlorophyll, and structural properties such as leaf area index (LAI). %N was destructively measured in 26 broadleaf, needle leaf, and mixed stand plots to represent the different species and canopy structure. The canopy foliar %N is defined as the plot-level mean foliar %N of all species weighted by species canopy foliar mass fraction. Our results showed that the variance of canopy foliar %N is mainly explained by functional type and species composition. The normalized difference nitrogen index (NDNI) produced the most accurate estimation of %N (R²_CV = 0.79, RMSE_CV = 0.26). A comparable estimation of %N was obtained by the chlorophyll index Boochs2 (R²_CV = 0.76, RMSE_CV = 0.27). In addition, the mean NIR reflectance (800–850 nm), representing canopy structural properties, also achieved a good accuracy in %N estimation (R²_CV = 0.73, RMSE_CV = 0.30). The PLSR model provided a less accurate estimation of %N (R²_CV = 0.69, RMSE_CV = 0.32). We argue that the good performance of all three categories of vegetation indices in %N estimation can be attributed to the synergy among plant traits (i.e., canopy structure, leaf chemical and optical properties) while these traits may converge across plant species for evolutionary reasons. Our findings demonstrated the feasibility of using hyperspectral vegetation indices to estimate %N in a mixed temperate forest which may relate to the effect of the physical basis of nitrogen absorption features on canopy reflectance, or the biological links between nitrogen, chlorophyll, and canopy structure. Full article