Search Results (23)

Cr-based composite coatings with superior wear resistance are in growing demand for high-performance applications in the automotive, aerospace, and general manufacturing sectors. In this study, an Al10Cu alloy produced via powder metallurgy was coated with a chromium/nanodiamond (Cr/ND) composite layer using an electrodeposition process to enhance its tribological performance. The coatings were characterized using scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray diffraction. The resulting Cr/ND layer exhibited a uniform thickness of 73.5–76.2 μm and markedly improved surface hardness (809.4 HV), representing a 15-fold increase over the uncoated alloy (53.6 HV). Pin-on-disk tribological testing under dry sliding conditions showed complete elimination of detectable mass loss (0.00 mg vs. 0.55 mg for uncoated) within the measurement system resolution, indicating excellent resistance to both abrasive and adhesive wear. XRD analysis revealed the formation of a hexagonal close-packed Cr₂H phase with incorporated nanodiamond particles. To capture and predict the temporal evolution of the friction coefficient, a customized dual-layer long short-term memory neural network—optimized with a look-back window of 3 timesteps and ReLU-activated dense layers—was implemented. The model achieved superior predictive performance on the coated system, with validation and test R² values of 0.9973 and 0.9965, respectively, demonstrating enhanced modeling accuracy for surface-engineered materials. These findings demonstrate a significant advancement in wear protection for aluminum alloys and introduce a robust data-driven approach for real-time friction prediction in engineered surfaces. Full article

The development of collagen-based composite materials offers new opportunities for designing bioactive porous structures with tunable properties. This study focuses on sponges or scaffolds fabricated from fish skin-derived tropocollagen combined with detonation nanodiamonds (NDs), aiming to explore how incorporation of NDs and application of radiation, as a potential sterilization method, influence structural and functional characteristics of the material. Freeze-dry methods of sponge fabrication resulted in a bilayered structure of open porosity, with microporosity at the top and a microchannel at the lower part of the material. The sponges demonstrated mechanical properties with relatively low elongation of below 10%, while the maximum stress was reduced by ca. 20% due to irradiation. Hydration and absorption experiments, mimicking the resorption of collagen in physiological conditions of expected application as wound dressing material, demonstrated controllable fluid uptake and gradual material dissolution, taking place over several hours, depending essentially on the irradiation treatment and morphological characteristics of the sponge. These findings highlight the versatility of collagen–nanodiamond composites as platforms, in which structural design and processing parameters control performance. Moreover, they provide a strong indication of the expected behavior of collagen–nanoparticle systems, including those incorporating NDs modified to impart specific biological functionality, such as antimicrobial activity. Full article

This study focuses on improving the operational properties of a magnesium potassium phosphate (MPP) matrix MgKPO₄ × 6H₂O for the immobilization of radioactive waste (RW) by introducing detonation nanodiamonds (NDs). The study evaluates the impact of NDs on the phase composition of the resulting composite based on the MPP matrix (further referred to as MPP-ND composite), as well as its compressive and flexural strength, porosity, thermal conductivity, and leaching resistance to actinides (²³⁹Pu, ²³⁸U) and europium (as a lanthanide simulator). It was found that the optimal content of NDs in the composite is 1 wt%, along with 20 wt% of wollastonite as a reinforcing additive. This MPP-ND composite exhibited high compressive and flexural strengths of 24 and 4 MPa, respectively, a thermal conductivity coefficient of (0.5–1.0) W/(m∙K) in the interval of (47–510) °C, and a minimal open porosity of no more than 5%. An increase in hydrolytic stability to leaching of actinides and europium due to their prior sorption on NDs was observed. The leaching rates of ²³⁹Pu, ²³⁸U, and Eu from the MPP-ND composite on the 28th day of sample contact with water were 3.5 × 10⁻⁶, 1.5 × 10⁻⁴, and 4.0 × 10⁻⁶ g/(cm²·day), respectively. Thus, for the first time, data on the influence of NDs on the physicochemical properties and hydrolytic stability of MPP-ND composite demonstrating the practical applicability of this composite for RW immobilization have been obtained. Full article

TiCN-based cermets have been widely used as cutting tools and wear-resistant coatings due to their excellent performance. New kinds of TiCN-based cermets that are being developed to have high performance have attracted extensive attention. In this work, TiCN-based cermets with nano-diamonds (NDs) as an additive were prepared by spark plasma sintering (SPS). The phase composition, microstructure, mechanical properties and wear behavior of the samples with different ND contents were systematically studied. The results show that a large fraction of the added nano-diamonds was transformed into graphite, while part of the diamond phase remained. The aggregation of the graphite became serious with more than 7 wt.% added nano-diamond. The relative density of the samples was approximately 87% and the hardness decreased with an increase in the added amount of nano-diamond. The average coefficient of friction of the samples ranged from 0.4 to 0.5. The graphite generated from nano-diamond lead to a deterioration in the mechanical properties of the prepared cermets and a reduction in their wear resistance. How to reduce the graphitization of diamond during the preparation of cermets should be considered in the follow-up study. Full article

The extensive use of lithium-ion batteries and other energy storage systems (ESS) in recent years has resulted in a critical need for effective thermal management solutions that ensure safe and reliable operations. Carbon-based materials (C-bMs) are a promising candidate for addressing the thermal challenges in ESS due to their unique thermal, electrical, and structural properties. This article provides a concise overview of C-bM thermal management solutions for improved battery safety. The key thermal management requirements and failure modes associated with battery systems are highlighted, underscoring the importance of effective battery thermal management (BTM). Various forms of C-bMs, including graphite, graphene, carbon nanotubes, carbon foams, nanodiamonds, and graphdiyne, are examined for their potential applications in battery thermal management systems. The recent innovations and advancements in C-bM thermal management solutions, such as phase change composites, heat pipes, and thermal interface materials, are highlighted. Furthermore, the latest research trends focus mainly on the development of hybrid battery thermal management solutions, carbon-based aerogels, and complex C-bM structures with tailored thermal pathways for optimized thermal management. Most of the current innovations are still at the laboratory scale; hence, future research efforts will be focused on developing integrated multi-functional C-bMs, sustainable and scalable manufacturing techniques, self-healing C-bMs composites, intelligent C-bMs, and further explorations of uncommon C-bMs. These advancements are bound to enhance performance, sustainability, and application-specific adaptations for BTM. This article provides valuable insights for researchers, and stakeholders interested in leveraging C-bMs for BTM. Full article

More than 15 years ago, the study of nanodiamond (ND) powders as a material for designing reflectors of very cold neutrons (VCNs) and cold neutrons (CNs) began. Such reflectors can significantly increase the efficiency of using such neutrons and expand the scope of their application for solving applied and fundamental problems. This review considers the principle of operation of VCN and CN reflectors based on ND powders and their advantages. Information is presented on the performed experimental and theoretical studies of the effect of the size, structure, and composition of NDs on the efficiency of reflectors. Methods of chemical and mechanical treatments of powders in order to modify their chemical composition and structure are discussed. The aim is to avoid, or at least to decrease, the neutron inelastic scatterers and absorbers (mainly hydrogen atoms but also metallic impurities and nitrogen) as well as to enhance coherent elastic scattering (to destroy ND clusters and sp² carbon shells on the ND surface that result from the preparation of NDs). Issues requiring further study are identified. They include deeper purification of NDs from impurities that can be activated in high radiation fluxes, the stability of NDs in high radiation fluxes, and upscaling methods for producing larger quantities of ND powders. Possible ways of solving these problems are proposed. Full article

This paper presents a study on the prospects of functionalizing nanodiamonds (NDs) with aminoacetic acid to obtain high-strength composites based on an epoxy matrix. The impact of the functionalization of the ND surface with aminoacetic acid in various concentrations on the properties of the epoxy composite was assessed. The success of grafting amine onto the ND surface was confirmed by X-ray phase analysis and IR spectroscopy. The results show a significant decrease in the average size of ND particles, from 400 nm for the pristine ones to 35 nm, and the contact angle, from 27° to 22°, with an increase in the specific surface area after treatment with a 5% solution of aminoacetic acid. Reducing the average size of NDs allows them to be better distributed throughout the epoxy matrix, which, as a result of the formation of chemical interaction at the matrix–nanofiller phase interface, can significantly increase the strength of the obtained composite. The addition of NDs treated with aminoacetic acid ensures an increase in the deformation-strength properties of epoxy composites by 19–23% relative to an epoxy composite containing the pristine NDs. Moreover, the presence of functionalized NDs significantly influences the structure and thermal stability of the epoxy nanocomposite. Full article

In this work, a diamond/Ti/diamond multilayer structure has been fabricated by successively following thin-film CVD and PVD routes. It has been found that a combined pre-treatment of the silicon base substrate, via argon plasma etching for creating surface roughness and, thereafter, detonation nanodiamond (DND) seeding, helps in the nucleation and growth of well-adherent CVD diamond films with a well-defined Raman signal at 1332 cm⁻¹, showing the crystalline nature of the film. Ti sputtering on such a CVD-grown diamond surface leads to an imprinted bead-like microstructure of the titanium film, generated from the underlying diamond layer. The cross-sectional thickness of the titanium layer can be found to vary by as much as 0.5 µm across the length of the surface, which was caused by a subsequent hydrogen plasma etching process step of the composite film conducted after Ti sputtering. The hydrogen plasma etching of the Ti–diamond composite film was found to be essential for smoothening the uneven as-grown texture of the films, which was developed due to the unequal growth of the microcrystalline diamond columns. Such hydrogen plasma surface treatment helped further the nucleation and growth of a nanocrystalline diamond film as the top layer, which was deposited following a similar CVD route to that used in depositing the bottom diamond layer, albeit with different process parameters. For the latter, a hydrogen gas diluted with PH₃ precursor recipe produced smaller nanocrystalline diamond crystals for the top layer. The titanium layer in between the two diamond layers possesses a very-fine-grained microstructure. Transmission electron microscopy (TEM) results show evidence of intermixing between the titanium and diamond layers at their respective interfaces. The thin films in the composite multilayer follow the contour of the plasma-etched silicon substrate and are thus useful in producing continuous protective coatings on 3D objects—a requirement for many engineering applications. Full article

In this study, we aimed to design and research proton-conducting membranes based on Aquivion^®-type material that had been modified with detonation nanodiamonds (particle size 4–5 nm, 0.25–5.0 wt. %). These nanodiamonds carried different functional groups (H, OH, COOH, F) that provided the hydrophilicity of the diamond surface with positive or negative potential, or that strengthened the hydrophobicity of the diamonds. These variations in diamond properties allowed us to find ways to improve the composite structure so as to achieve better ion conductivity. For this purpose, we prepared three series of membrane films by first casting solutions of perfluorinated Aquivion^®-type copolymers with short side chains mixed with diamonds dispersed on solid substrates. Then, we removed the solvent and the membranes were structurally stabilized during thermal treatment and transformed into their final form with –SO₃H ionic groups. We found that the diamonds with a hydrogen-saturated surface, with a positive charge in aqueous media, contributed to the increase in proton conductivity of membranes to a greater rate. Meanwhile, a more developed conducting diamond-copolymer interface was formed due to electrostatic attraction to the sulfonic acid groups of the copolymer than in the case of diamonds grafted with negatively charged carboxyls, similar to sulfonic groups of the copolymer. The modification of membranes with fluorinated diamonds led to a 5-fold decrease in the conductivity of the composite, even when only a fraction of diamonds of 1 wt. % were used, which was explained by the disruption in the connectivity of ion channels during the interaction of such diamonds mainly with fluorocarbon chains of the copolymer. We discussed the specifics of the mechanism of conductivity in composites with various diamonds in connection with structural data obtained in neutron scattering experiments on dry membranes, as well as ideas about the formation of cylindrical micelles with central ion channels and shells composed of hydrophobic copolymer chains. Finally, the characteristics of the network of ion channels in the composites were found depending on the type and amount of introduced diamonds, and correlations between the structure and conductivity of the membranes were established. Full article

Carbon-based nanomaterials have rapidly advanced over the last few decades. Fullerenes, carbon nanotubes, graphene and its derivatives, graphene oxide, nanodiamonds, and carbon-based quantum dots have been developed and intensively studied. Among them, fullerenes have attracted increasing research attention due to their unique chemical and physical properties, which have great potential in a wide range of applications. In this article, we offer a comprehensive review of recent progress in the synthesis and the chemical and physical properties of fullerenes and related composites. The review begins with the introduction of various methods for the synthesis of functionalized fullerenes. A discussion then follows on their chemical and physical properties. Thereafter, various intriguing applications, such as using carbon nanotubes as nanoreactors for fullerene chemical reactions, are highlighted. Finally, this review concludes with a summary of future research, major challenges to be met, and possible solutions. Full article

An amorphous carbon film with embedded detonation nanodiamond (DND) particles (a-C:ND) was produced by magnetron sputtering of nanodiamond powder. An Ag film was deposited on the carbon structure by radiofrequency magnetron sputtering. The silver film was irradiated with a 150 eV Ar⁺ to form plasmonic-active nanoparticles (NP) on the surface of the a-C:ND. The structure of the obtained a-C:ND and a-C:ND/Ag structures were studied by scanning and transmission electron microscopy, electron energy-loss spectroscopy, UV–Visible absorption spectroscopy, Raman spectroscopy, and fluorescence lifetime imaging at two-photon excitation. The analysis revealed 76% of sp³-carbon and a good dispersion of diamond nanoparticles in the a-C. Surface-enhanced Raman scattering (SERS) was applied to investigate the a-C:ND/Ag structure, allowing for the observation of SERS from the sp²-carbon species and the absence of significant a-C:ND damage after Ar⁺ irradiation of the Ag overlayer. A plasmonic-metal-enhanced luminescence was observed at one- and two-photon excitations, revealing a two- to five-fold intensity increase. The activity of the used DNDs was tested using the agar diffusion method and observed against the bacteria of Bacillus subtilis, Staphylococcus aureus, and Escherichia coli and the fungi of Aspergillus niger, Aspergillus fumigatus, and the yeast of Candida albicans, showing DND activity against all the test strains of fungi. Full article

The paper considers the development of a technological scheme for preparing metal matrix nanocomposites based on the interaction between nanodiamond reinforcing particles and a chromium matrix when being heated, forming chromium carbide nanoparticles. These carbides are in situ synthesized ceramic reinforcing nanoparticles. The first stage of preparing composites is to obtain composites with the chromium matrix and nanodiamond reinforcing particles. For this purpose, mechanical alloying is used, i.e., processing in planetary mills. The size of a primary nanodiamond particle is 5 nm, but they are combined in agglomerates that are hundreds of micrometers in size. The time of processing in the planetary mill defines the crushing degree of the agglomerates. In this study, processing was carried out for 0.5 h, 2 h, and 4 h. The second stage for obtaining composites with reinforcing particles of chromium carbides is thermal processing. Explorations using the method of differential scanning calorimetry showed that reducing the size of nanodiamond reinforcing particles (by prolonging the time of processing in the planetary mill) leads to a decrease in the initial temperature of the reaction for developing carbides. The worked-out technique for obtaining composites was patented in the Russian Federation (the patent for invention 2772480). Full article

Compositional proton-conducting membranes based on perfluorinated Aquivion^®-type copolymers modified by detonation nanodiamonds (DND) with positively charged surfaces were prepared to improve the performance of hydrogen fuel cells. Small-angle neutron scattering (SANS) experiments demonstrated the fine structure in such membranes filled with DND (0–5 wt.%), where the conducting channels typical for Aquivion^® membranes are mostly preserved while DND particles (4–5 nm in size) decorated the polymer domains on a submicron scale, according to scanning electron microscopy (SEM) data. With the increase in DND content (0, 0.5, and 2.6 wt.%) the thermogravimetric analysis, potentiometry, potentiodynamic, and potentiotatic curves showed a stabilizing effect of the DNDs on the operational characteristics of the membranes. Membrane–electrode assemblies (MEA), working in the O₂/H₂ system with the membranes of different compositions, demonstrated improved functional properties of the modified membranes, such as larger operational stability, lower proton resistance, and higher current densities at elevated temperatures in the extended temperature range (22–120 °C) compared to pure membranes without additives. Full article

Improving the operating performance of superhard composites is an important and urgent task, due to a continuing industrial need. In this work, diamond composites with high wear resistance were obtained by sintering fluorinated mixtures of micron-sized diamonds with nanodiamonds at high pressures and temperatures (7–8 GPa, 1550–1700 °C). Aluminum and cobalt powders were added to the diamond mixture to activate the process. The external infiltration of nickel into the diamond layer was carried out additionally during the sintering process, and the effects of nickel infiltration on the structure and properties of composites were studied. The metal melt ensured the mass transfer of carbon within a volume, and the formation of a strong diamond framework. The composition of the additives was selected in such a way that the binding phase became ultimately composed of the intermetallic AlNi_xCo_1−x(x ≤ 1). The Young’s modulus of composites synthesized in this way had a value of 850 GPa, and their wear resistance when turning white granite was more than twice as high as that of premium commercial PDC. The obtained results thus demonstrate that by using nickel to increase melt infiltration into diamond-based composites, the mechanical properties of Al/Co/fluorinated diamond compositions, studied previously, can be further improved. Full article

This investigation is motivated by increasing interest in diamond and composite films for applications in biomedical and electronic devices. A biomimetic strategy is based on the use of commercial bile acids, such as ursodeoxycholic acid (UDCA) and hyodeoxycholic acid (HDCA). Composite films are developed using UDCA and HDCA as solubilizing agents for poly(ethyl methacrylate) (PEMA) in isopropanol and as dispersing agents for micro- and nanodiamonds. In this approach, the use of traditional toxic solvents for PEMA dissolution is avoided. The ability to obtain high concentrations of high molecular mass PEMA and disperse diamond particles in such solutions is a key factor for the development of a dip-coating method. The PEMA dissolution and diamond dispersion mechanisms are discussed. The composition and microstructure of the films can be varied by variation of the diamond particle size and concentration in the suspensions. The films can be obtained as singular layers of different compositions, multilayers of similar composition, or alternating layers of different compositions. The films combine corrosion protection property and biocompatibility of PEMA with advanced functional properties of diamonds. Full article