Search Results (296)

Persistent reactive azo dyes released from textile finishing are a serious threat to water systems, but effective methods using sunlight to break them down are still limited. Everzol Yellow 3RS (EY-3RS) is particularly recalcitrant: past studies have relied almost exclusively on physical adsorption onto natural or modified clays and zeolites, and no photocatalytic pathway employing engineered nanomaterials has been documented to date. This study reports the synthesis, characterization, and performance of a visible-active ternary nanocomposite, Cu₄O₃/ZrO₂/TiO₂, prepared hydrothermally alongside its binary (Cu₄O₃/ZrO₂) and rutile TiO₂ counterparts. XRD, FT-IR, SEM-EDX, UV-Vis, and PL analyses confirm a heterostructured architecture with a narrowed optical bandgap of 2.91 eV, efficient charge separation, and a mesoporous nanosphere-in-matrix morphology. Photocatalytic tests conducted under midsummer sunlight reveal that the ternary catalyst removes 91.41% of 40 ppm EY-3RS within 100 min, markedly surpassing the binary catalyst (86.65%) and TiO₂ (81.48%). Activity trends persist across a wide range of operational variables, including dye concentrations (20–100 ppm), catalyst dosages (10–40 mg), pH levels (3–11), and irradiation times (up to 100 min). The material retains ≈ 93% of its initial efficiency after four consecutive cycles, evidencing good reusability. This work introduces the first nanophotocatalytic strategy for EY-3RS degradation and underscores the promise of multi-oxide heterojunctions for solar-driven remediation of colored effluents. Full article

Poly(trimethylene terephthalate) (PTT) is a thermoplastic polyester with a unique structure due to having three methylene groups in the glycol unit. PTT competes with poly(ethylene terephthalate) (PET) and poly(butylene terephthalate) (PBT) in carpets, textiles, and thermoplastic materials, primarily due to the development of economically efficient synthesis methods. PTT is widely utilized in textiles, carpets, and engineering plastics because of its advantageous properties, including quick-drying capabilities and wrinkle resistance. However, its low melting point, resistance to chemicals, and brittleness compared to PET, have limited its applications. To address some of these limitations for targeted applications, PTT nanocomposites incorporating clay, carbon nanotube, silica, and ZnO have been developed. The distribution of nanoparticles within the PTT matrix remains a significant challenge for its potential applications. Several techniques, including sol–gel blending, melt blending, in situ polymerization, and in situ forming methods have been developed to obtain better dispersion. This review discusses advancements in the synthesis of various PTT nanocomposites and the effects of nanoparticles on the isothermal and nonisothermal crystallization of PTT. Full article

This study investigates the hydrogen permeability of injection-molded polyamide 6 (PA6) nanocomposites reinforced with organo-modified montmorillonite (OMMT) at varying concentrations (1, 2.5, 5, and 10 wt. %) for potential use as Type IV composite-overwrapped pressure vessel (COPV) liners. While previous work examined their mechanical properties, this study focuses on their crystallinity, morphology, and gas barrier performance. The precise inorganic content was determined using thermal gravimetry analysis (TGA), while differential scanning calorimetry (DSC), wide-angle X-ray diffraction (WAXD), and scanning electron microscopy (SEM) were used to characterize the structural and morphological changes induced by varying filler content. The results showed that generally higher OMMT concentrations promoted γ-phase formation but also led to increased agglomeration and reduced crystallinity. The PA6/OMMT-1 wt. % sample stood out with higher crystallinity, well-dispersed clay, and low hydrogen permeability. In contrast, the PA6/OMMT-2.5 and -5 wt. % samples showed increased permeability, which corresponded to WAXD and SEM evidence of agglomeration and DSC results indicating a lower degree of crystallinity. PA6/OMMT-10 wt. % showed the most-reduced hydrogen permeability compared to all other samples. This improvement, however, is attributed to a tortuous path effect created by the high filler loading rather than optimal crystallinity or dispersion. SEM images revealed significant OMMT agglomeration, and DSC analysis confirmed reduced crystallinity, indicating that despite the excellent barrier performance, the compromised microstructure may negatively impact mechanical reliability, showing PA6/OMMT-1 wt. % to be the most balanced candidate combining both mechanical integrity and hydrogen impermeability for Type IV COPV liners. Full article

One of the most interesting and poorly studied carriers of medicinal substances is the polymer clay composite material (PCCM). Bentonite clays are used in pharmacy for the manufacturing of various dosage forms, as well as in the adsorption of drugs to slow their release. Polymer–clay nanocomposites have demonstrated significantly improved properties compared to pure polymers. A review of recent scientific advances has shown promising results regarding the application of polymer–clay materials in medicine and bioengineering, particularly in the development of carrier sorbents with prolonged action for controlled drug release. As a result, interest in polymer–clay systems is steadily growing and gaining momentum. This paper focuses on the structure and properties of bentonite clays, including their sorption, ion exchange, binding, and rheological properties. The methods for preparing intercalated and exfoliated nanocomposites, such as radical intercalative polymerization in situ on clay surfaces, are reviewed. Furthermore, the improved efficacy and exposure times of PCCMs, combined with their enhanced bactericidal properties, are analyzed for the creation of universal and multifunctional preparations for medical use. Full article

This study prepared epoxy–clay nanocomposites (ECNs) by incorporating organophilic clays modified with either non-redox cetyltrimethylammonium bromide (CTAB) or redox-active aniline pentamer (AP), then compared their anticorrosion performance on metal substrates in saline environments. The test solution contained 2 wt% alkaline copper quaternary (ACQ) wood preservatives. Cold-rolled steel (CRS) panels coated with the ECNs were evaluated via electrochemical impedance spectroscopy (EIS) in saline media both with and without ACQ. For CRS coated with unmodified epoxy, the Nyquist plot showed impedance dropping from 255 kΩ to 121 kΩ upon adding 2 wt% ACQ—indicating that Cu²⁺ ions accelerate iron oxidation. Introducing 1 wt% CTAB–clay into the epoxy increased impedance from 121 kΩ to 271 kΩ, while 1 wt% AP–clay raised it to 702 kΩ. This improvement arises because the organophilic clay platelets create a more tortuous path for Cu²⁺ and O₂ diffusion, as confirmed by ICP–MS measurements of Cu²⁺ after EIS and oxygen permeability tests (GPA), thereby slowing iron oxidation. Moreover, ECN coatings containing AP–clay outperformed those with CTAB–clay in corrosion resistance, suggesting that AP not only enhances platelet dispersion but also promotes formation of a dense, passive metal oxide layer at the coating–metal interface, as shown by TEM, GPA, and XRD analyses. Finally, accelerated salt-spray exposure following ASTM B-117 yielded corrosion behavior consistent with the EIS results. Full article

Organic dyes are pollutants that threaten aquatic life and human health. These dyes are used in various industries; therefore, recent research focuses on the problem of their removal from wastewater. The aim of this study is to examine the clay/gum arabic nanocomposite (CG/NC) as an adsorbent to adsorb methylene blue (MB) and crystal violet (CV) dyes from synthetic wastewater. The CG/NC was characterized using Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), and Brunaure–Emmett–Teller (BET). The effect of parameters that may influence the efficiency of removing MB and CV dyes was studied (dosage of CG/NC, contact time, pH values, initial concentration, and temperature), and the optimal conditions for removal were determined. Furthermore, an artificial neural network (ANN) model was adopted in this study. The results indicated that the adsorption behavior adhered to the Langmuir model and conformed to pseudo-second-order kinetics. The results also indicated that the removal efficiency reached 99%, and q_max reached 66.7 mg/g and 52.9 mg/g for MB and CV, respectively. Results also proved that CG/NC can be reused up to four times with high efficiency. The ANN models proved effective in predicting the process of the removal, with low mean squared errors (MSE = 1.824 and 1.001) and high correlation coefficients (R² = 0.945 and 0.952) for the MB and CV dyes, respectively. Full article

The present study aims to prepare a composite via pyrolysis, based on sodium alginate (SA) and a natural clay collected from the eastern region of Morocco, specifically the OUJDA area (C.O.R), for use in the disposal process of emerging pharmaceuticals. The strategy of rapid microwave heating followed by nitrogen calcination at 500 °C was successfully applied to produce the pyrolyzed carbonaceous materials. The removal of paracetamol (PCT) by adsorption on the carbonaceous clay (ca-C.O.R) composite was investigated to determine the effect of operating parameters (initial contaminant concentration, contact time, pH, and temperature) on the efficiency of PCT removal. The nanocomposite was analyzed using various techniques, including the nitrogen gas adsorption–desorption isothermal curve, X-ray diffraction, scanning electron microscopy, and Fourier transform infrared spectroscopy. Three models were used to describe the kinetic adsorption, and it was found that the experimental kinetic data fit well with a pseudo-second-order kinetic model with a coefficient of determination R² close to one, a nonlinear chi-square value close to zero, and a reduced root mean square error RMSE (R² → 1, X² → 0 and lower RMSE). The adsorption was best described by the Sips isotherm. The ca-C.O.R composite achieved a PCT removal efficiency of 91% and a maximum adsorption capacity of 122 mg·g⁻¹ improving on the performance of previous work. Furthermore, the variation in enthalpy (∆H°), Gibbs free energy (∆G°), and entropy (∆S°) indicated that the adsorption is exothermic in nature. The composite has shown promising efficiency for the adsorption of PCT as a model of emergent pollutant from aqueous solutions, making it a viable option for industrial wastewater treatment. Using Density Functional Theory (DFT) along with the 6-31G (d) basis set, the geometric structure of the molecule was determined, and the properties were estimated by analyzing its boundary molecular orbitals. The adsorption energy of PCT on MMT and ca-C.O.R studied using the Monte Carlo (MC) simulation method was −120.3 and −292.5 (kcal·mol⁻¹), respectively, which shows the potential of the two adsorbents for the emerging product. Full article

This study uses the melt compounding method to recycle polypropylene-based car bumper waste (PP-CBW) in order to produce nanocomposite films for mulch application. The nanocomposite films were compounded by mixing virgin linear low-density polyethylene (LLDPE) with PP-CBW at a constant ratio of 4:1 in the presence of different percentages of nanofillers. Nanocomposites reinforced with nanoclays were compatibilized with an anhydride grafted polyethylene (PE-g-MAH), at a constant compatibilizer-to-clay ratio equal to 3, to improve the adherence between the nonpolar matrix and the hydrophilic nanoclay and acrylic paint present in the car bumper. An extruder with a corotating twin screw was used to produce blends of different compositions. To create nanocomposite films, the mixtures were further processed in a blown film extruder. The effect of the presence of nanoclays on the barrier, thermal, and mechanical properties of the nanocomposite films was investigated. The dispersion of clay layers in the matrix was examined by atomic force microscopy (AFM). The results indicate that 3 wt% of clay loading maximized the tensile strength in the transverse direction (TD) and machine direction (MD). A 1 wt% clay loading increased the MD tear resistance by 66% and manifested an optimum dart impact strength. Significant improvements in thermal and barrier properties were also achieved in the presence of 3 wt% clay loading. Full article

This study presents the synthesis and utilization of a conductive polymer/clay nanocomposite for the adsorptive removal of an azo dye, methyl orange (MO), from artificial wastewater. The PANI-CLAY nanocomposites were synthesized by means of the oxidative polymerization route and characterized using the Brunauer, Emmett and Teller thermogravimetric analysis, Fourier-Transform Infrared spectra and Scanning Electron Microscopy. The surface area of the clay mineral decreased from 37.38 to 13.44 m²/g for 10 g of PANI/CLAY when made into a composite with PANI. Such behavior is most likely due to the possible coverage of the clay surface by a layer of PANI. Further, TGA revealed that incorporating CLAY significantly improved the thermal stability of PANI. The effects of adsorption process parameters such as adsorbent dosage (0.006–0.4 g), solution pH (1, 3, 5, 7, 9, 11 and 13), initial dye concentration (50–300 ppm), contact time (1–80 min) and temperature (25 °C, 30 °C, 35 °C and 40 °C) on the % removal efficiency were investigated. The experimental data were well fitted by the pseudo-second-order kinetic model. The maximum uptake capacity (q_max) values increased from 42.017 mg/g (PANI/CLAY 10 g) to 55.87 mg/g for PANI alone. The uptake capacity implies that the prepared adsorbents possess excellent adsorption characteristics with high affinity towards organic dye removal. Full article

Condensation-type polysiloxane composites with montmorillonite (MMT) of different organic modifications were prepared in this study. X-ray diffraction (XRD) characterization revealed that the higher degree of organic modification in Cloisite 20A, compared to that in Cloisite 30B, resulted in a larger interlayer spacing between the clay platelets. This facilitates the insertion of elastomer chains between the layers, enabling easier exfoliation and dispersion in the elastomeric matrix. Differential scanning calorimetry (DSC) showed that the reinforcing agents used reduced the cold crystallization temperature of the condensation-type polysiloxane while leaving the glass transition and melting temperatures nearly unaffected. Additionally, the nanocomposites exhibited slightly lower crystallization and melting enthalpies compared to pure silicone. Thermogravimetric analysis (TGA) showed that incorporating the two organically modified clays (Cloisite 20A and Cloisite 30B) into the condensation-type polysiloxane significantly improved the thermal stability of the resulting nanocomposites. This improvement was reflected in the significant increase in the onset and maximum degradation rate temperatures across all examined reinforcement ratios. It was observed that a higher degree of organic modification in MMT (Cloisite 20A) resulted in a more efficient dispersion in the PDMS matrix and enhanced the thermal stability of the composites. These PDMS nanocomposites could be suitable as protective coatings for devices exposed to elevated temperatures. Full article

The use of essential oil components as natural antifungal preservatives in the active packaging of bread is an innovative approach that leverages the antimicrobial properties of these compounds to extend the shelf life of bread and ensure its safety. The aim of the present work was the thorough investigation of the antioxidant properties and antifungal activity of low-density polyethylene (LDPE or PE) nanocomposite films with organically modified montmorillonite (O) loaded with carvacrol (C) or thymol (T) as a function of time, starting from 2 months and concluding at 12 months. The films PE_OC and PE_OT were prepared through the evaporation/adsorption method, a green methodology developed by our group compatible with food packaging. For a comprehensive analysis of the synthesized films’ oxygen permeability (OTR), measurements were employed, indicating that the incorporation of clay–bioactive nanocarriers into LDPE films reduced their oxygen permeability. A thorough analysis in terms of the antioxidant activity of the films was assessed at various intervals (2, 3, 6, and 12 months), showing high antioxidant activity for films PE_OC10 and PE_OT10 (polyethylene with 10% wt. organically modified montmorillonite loaded with carvacrol or thymol), even at 12 months. Based on the overall analysis, the PE_OC10 film was identified as the most effective option in the antifungal evaluation conducted using white bread, demonstrating substantial inhibition of fungal growth for up to six months. Full article

Nanocomposite hydrogels are gaining significant attention for biomedical applications in soft tissue engineering due to the increasing demand for highly flexible and durable soft polymer materials. This research paper focused on investigating and optimizing a procedure for the development of novel nanocomposite hydrogels based on poly(2-hydroxyethyl methacrylate)-co-(2-acrylamido-2-methylpropane sulfonic acid) (HEMA/AMPSA) copolymers. These hydrogels were synthesized through a grafting-through process, where the polymer network was formed using a modified clay crosslinker. The layered double hydroxide (LDH) clay modified with 3-(trimethoxysilyl)propyl methacrylate (ATPM) was synthesized using a novel recipe through a two-step procedure. The nanocomposite hydrogel compositions were optimized to achieve soft hydrogels with high flexibility. The developed materials were analyzed for their mechanical and morphological properties using tensile and compressive tests, transmission electron microscopy (TEM), scanning electron microscopy (SEM), and micro-computed tomography (micro-CT). The swelling behavior, network density, and kinetic diffusion mechanism demonstrated the specific characteristics of the materials. The modified LDH-ATPM was further characterized using Thermogravimetry (TGA), FTIR-ATR and X-ray diffraction (XRD). Biological assessments on human adipose-derived stem cells (hASCs) were essential to evaluate the biocompatibility of the nanocomposite hydrogels and their potential for soft tissue applications. Full article

Montmorillonite (Mont) is a natural two-dimensional material with a 2:1 layered silicate crystal structure. It possesses abundant surface groups, cation exchange capacity, and adsorption performance. In addition, it has other advantages such as abundant reserves, environmental friendliness, strong mechanical stability, and a large specific surface area. As such, it shows excellent potential for application in environmental remediation. In the following paper, we focus on the removal of TCS (triclosan) from an aqueous environment by utilizing montmorillonite-supported bimetallic Fe/Ag particles. We use scanning electron microscopy, X-ray diffraction patterns, Fourier-transform infrared spectra, and specific surface area to analyze the structure, morphology, and composition of these nanocomposites. The effects of the pH, different materials, contact time, and different initial concentrations on the degradation efficiency of TCS were studied systematically. Based on the results of our study, montmorillonite-supported bimetallic Fe/Ag nanoparticles (Fe/Ag-Mont) should be categorized as a type of mesoporous material of high uniformity because the pore size of all its catalysts ranges from 10 to 20 nm, and they are well-distributed. The Si-O stretching vibrations of montmorillonite can be changed by adding Fe/Ag. We found that Fe or Ag combined with -O to form a new bond and interacted with Si-O, and the incorporation of Fe/Ag-Mont nanoparticles removed TCS with better reduction rates. By enhancing reduction capacity, the pH was below 4 due to H• species generation by Fe/Ag. H• was the main factor enhancing the redox reaction in reducing TCS. The pH controlled the competition between Fe corrosion and silver formation, which enabled the system to self-regulate. In addition, this study provided a suitable method of efficiently synthesizing clay-supported bimetallic nano-system materials for reduction. Full article

This work focuses on the preparation and application of silver nanoparticles/organophilic clay/polyethylene glycol for the catalytic reduction of the contaminants methylene blue (MB) and 4-nitrophenol (4-NP) in a simple and binary system. Algerian clay was subjected to a series of treatments including acid treatment, ion exchange with the surfactant hexadecyltrimethylammonium bromide (HTABr), immobilization of polyethylene glycol polymer, and finally dispersion of AgNPs. The molecular weight of polyethylene glycol was varied (100, 200, and 4000) to study its effect on the stabilization of silver nanoparticles (AgNPs) and the catalytic activity of the resulting samples. The results showed that the catalyst with the highest molecular weight of polyethylene glycol had the highest AgNP content. Catalyst mass, NaBH₄ concentration, and type of catalyst were shown to have a significant influence on the conversion and rate constant. The material with the highest silver nanoparticle content was identified as the optimal catalyst for the reduction of both pollutants. The measured rate constants for the reduction of methylene blue (MB) and 4-nitrophenol (4-NP) were 164 × 10⁻⁴ s⁻¹ and 25 × 10⁻⁴ s⁻¹, respectively. The reduction of MB and 4-NP in the binary system showed high selectivity for MB dye, with rate constants of 64 × 10⁻⁴ s⁻¹ and 9 × 10⁻⁴ s⁻¹ for MB and 4-NP, respectively. The reuse of the best catalyst via MB dye reduction for four cycles showed good results without loss of performance. Full article

The main purpose of this study is to prepare a melamine aniline formaldehyde foam, an MAF copolymer, with lower water sensitivity and non-flammability properties obtained by the condensation reaction of melamine, aniline, and formaldehyde. In addition, the preparation of MAFF composites with organoclay reinforcement was determined as a secondary target in order to obtain better mechanical strength, heat, and sound insulation properties. For the synthesis of foams, the microwave irradiation technique, which offers advantages such as faster reactions, high yields and purities, and reduced curing times, was used together with the heating technique and the effect of organoclay content on the structural and textural properties of foams and both heat insulation and mechanical stability was investigated. Virgin melamine formaldehyde foam, MFF, melamine aniline formaldehyde foam, MAFFF, and melamine aniline formaldehyde–organoclay nanocomposite foams prepared with various organoclay contents, MAFOCFs, were characterized by HRTEM, FTIR, SEM, and XRD techniques. From spectroscopic and microscopic analyses, it was observed that organoclay flakes could be exfoliated without much change in the resin matrix with increasing clay content. In addition, it was determined that aniline formaldehyde, which is thought to enter the main polymer network as a bridge, caused textural changes in the polymeric matrix, and organoclay reinforcement also affected these changes. Although the highest compressive strength was obtained in MAFOCF5 foam with high organoclay content (0.40 MPa), it was determined that the compressive strengths in the nanocomposites were generally quite high despite their low bulk densities. In the prepared nanocomposite with 0.30% organoclay content (MAFOCF2), 0.33 MPa compressive strength and 0.051 thermal conductivity coefficient were measured. For virgin polymers and composites, bulk density, thermal conductivity, and compressive strength values were determined in the order of magnitude as MFF > MAFOCF1 > MAFOCF5 > MAFOCF6 > MAFF > MAFOCF3 > MAFOCF2 > MAFOCF4; MFF > MAFF > MAFOCF6 > MAFOCF5 > MAFOCF1 > MAFOCF4 > MAFOCF3 > MAFOCF2 and MAFOCF5 > MAFOCF4 > MAFOCF2 > MAFF > MAFOCF6 > MFF > MAFOCF1 > MAFOCF3. As a result, both compressive strength and thermal conductivity values indicate that nanocomposite foam with 0.20 wt% organoclay content can be a promising new insulation material. Full article