Search Results (87)

The mean force between two highly like-charged macroions in the presence of monovalent counterions and added multivalent salt within solvents of varying dielectric constants was studied using Monte Carlo simulations. Without additional salt, the mean force is strongly repulsive at all macroion separations in solvents with a dielectric constant ${ϵ}_r$ ≥ 30. However, in solvents with ${ϵ}_r$≤ 30, macroions experience effective attraction, indicating that attractive interactions between highly charged macroions can occur even without multivalent salt in nonpolar solvents with low dielectric constants. The total multivalent counterion charge-to-total macroion charge ratio is defined as β which determines the amount of salt that is added to the system. At β = 0.075, the mean force becomes attractive at short separations in solvents with ${ϵ}_r$= 54 containing 1:3 salt, as well as in all solvents with 1:5 salt, while still exhibiting significant repulsion at longer separations. In contrast, for solvents with 1:3 salt and dielectric constants ${ϵ}_r$= 68 and ${ϵ}_r$= 78.4, the mean force turns attractive at a higher salt concentration, around β = 0.225. The shift in the mean force to an attractive state at short separations signifies charge inversion on the macroion surface when a sufficient amount of salt is present. At a stoichiometric ratio of multivalent counterions, long-range repulsion vanishes, and attraction becomes significant. However, with excess salt, the strength of the attractive mean force diminishes. Additionally, the attractive force at a given salt concentration increases as the dielectric constant decreases and is stronger in systems with 1:5 salt than in those with 1:3 salt. Full article

The rapid development of the global energy industry has driven an escalating worldwide demand for lithium resources. As a major lithium source, salt lake brines contain abundant divalent ions that hinder efficient lithium extraction. Compared with conventional lithium recovery technologies, nanofiltration membranes emerge as an energy-efficient and environmentally friendly alternative. Over the past decade, interfacial polymerization has been widely adopted to fabricate nanofiltration membranes for lithium–magnesium separation, with studies confirming the superior performance of positively charged membranes in distinguishing monovalent and divalent cations. This review systematically summarizes recent advancements in positively charged nanofiltration membranes synthesized via interfacial polymerization for lithium–magnesium separation, categorizing the design strategies into five distinct approaches. The correlations between intrinsic membrane structural characteristics and separation performance are critically analyzed. Furthermore, current challenges and future research directions are discussed to provide new perspectives for developing high-performance positively charged composite nanofiltration membranes. This work aims to inspire innovative designs and accelerate the practical implementation of nanofiltration technology in lithium extraction from salt lake brines. Full article

End-stage renal disease occurs when there is permanent loss of the kidney’s ability to filter toxins from the blood. Due to the limited number of transplants, dialysis is currently the most common treatment, but it significantly limits a patient’s lifestyle and has significant side effects. One solution is an artificial kidney, but significant challenges remain in its development. One challenge is the separation of glucose from urea. Nanofiltration is ideal for this separation; however, there is little understanding of the important parameters for this separation under physiological conditions. In this study, operating parameters (pressure and temperature) as well as feed conditions (increased glucose/salt) were explored for their effects on the separation of glucose from urea in six commercial membranes. The rejection of monovalent and divalent ions was also characterized. While increasing pressure increased flux, it had little effect on metabolite rejection, except for glucose, which increased above 20 psi. Increasing temperature led to a slight increase in flux and a slight decrease in the rejection of divalent ions. Glucose rejection was sensitive to feed conditions, while urea rejection was less affected. Divalent ions were rejected more strongly than monovalent ions and were also more affected by feed conditions. Full article

The development of highly effective natural-based adsorbents to face the increasing rates of CO₂ production and their delivery to the atmosphere are a big concern nowadays. For such purposes, synthetic and natural zeolites were modified via an ion exchange procedure to enhance the CO₂ uptake. Samples were characterized by SEM, EDS, TGA and nitrogen adsorption at 77 K, showing the correct incorporation of the new metals; in addition, the CO₂ adsorption isotherms were determined using a gas analyser. During the first stage, the role of the compensation cations for CO₂ adsorption was assessed by modifying a pure ZSM-5 synthetic zeolite with different metal precursors present in salt solutions via an ion exchange procedure. Then, five samples were studied; the samples modified with bivalent cation precursors (Zn²⁺ and Cu²⁺) presented a higher adsorption uptake than those modified with a monovalent cation (Na⁺ and K⁺). Specifically, the substitution of the compensation cations for Cu²⁺ increased the CO₂ capture uptake without affecting the surface properties of the zeolite. The results depict the prevalence of π-cation interactions enhanced by the field gradient induced by divalent cations and their lower ionic radii, if compared to monovalent ones. Subsequently, a natural zeolite was modified considering the best results of the previous phase. This Surface Response Methodology was implemented considering 11 samples by varying the concentration of the copper precursor and the time of the ion exchange procedure. A quantitative quadratic model to predict the adsorption uptake with an R² of 0.92 was obtained. The results depicted the optimal conditions to modify the used natural zeolite for CO₂ capture. The modification procedure implemented increased the CO₂ adsorption capacity of the natural zeolite more than 20%, reaching an adsorption capacity of 75.8 mg CO₂/g zeolite. Full article

A membrane system was applied for ultrapure water production from the treatment of saline effluent from the canned food industry. The industrial effluent presented a high saline concentration, including sodium chloride, calcium carbonate, calcium sulfates, and magnesium. The effluent was treated using a system of reverse osmosis (RO) and a post-treatment process consisting of ion exchange resins (IEXRs). The RO was accompanied by the addition of a hexametaphosphate dose (2, 6, and 10 mg/L) as an antiscalant to avoid the RO membrane scaling by minerals. In turn, IEXRs were used for water deionization to produce ultrapure water with a reduced concentration of monovalent ions. The antiscalant dose was 6 mg/L, producing clean water from RO permeates with an efficiency of 65–70%. The brine from RO was projected for its reuse in food industry processes. The clean water quality from RO showed 20% total dissolved solids (TDS) removal (equivalent to salts). The antiscalant inhibited the formation of calcium salt incrustation > 200 mg/L, showing low fouling. In turn, anionic resins removed 99.8% of chloride ions, whereas the monovalent salts were removed by a mix of cationic–anionic resin, producing ultrapure water with electrical conductivity < 3.3 µS/cm. The cost of ultrapure water production was 2.62 USD/m³. Full article

This study examines the effects of natural organic matter (NOM) and dissolved solids on fluoride (F⁻) retention in polyelectrolyte multilayer-based hollow-fiber nanofiltration membranes (dNF40). Lab-scale filtration experiments were conducted under varying operating conditions (initial salt concentration, NOM concentration, permeate flux, crossflow velocity, and recovery rate). dNF40 membranes exhibited F⁻ retention above 70% ± 1.2 in the absence of NOM and competing ions. However, when filtering synthetic model water (SMW) designed to simulate groundwater contaminated with high total dissolved solids (TDSs) and NOM, F⁻ retention decreased to approximately 60% ± 0.7, which was generally attributed to ion competition. Furthermore, despite limited declines in normalized permeability, the addition of NOM to SMW notably deceased F⁻ retention in the steady state to~20% due to fouling effects. The facilitated transport of the divalent cations Ca²⁺ and Mg²⁺ could be observed, as they accumulated in the organic fouling layer. While SO₄²⁻ retention remained relatively stable, the retention of monovalent anions (NO₃⁻, Cl⁻, and F⁻) decreased substantially due to drag effects. Na⁺ retention improved slightly to maintain electroneutrality. Feed salinity was shown to significantly affect separation efficiency, with PEC layers undergoing swelling and certain structural changes as the ionic strength increased. During batch filtration experiments at varying recovery rates, the retention of monovalent anions further decreased, with F⁻ retention reducing to just ~10% at a 90% recovery rate. This study provides valuable insights into better understanding and optimizing the performance of PEC-based NF membranes across diverse water treatment scenarios. Full article

Electrolytes play a vital role in the performance and safety of electrochemical energy storage devices, such as lithium-ion batteries (LIBs). While traditional LIBs rely on organic electrolytes, these flammable solutions pose safety risks and require expensive, moisture-sensitive manufacturing processes. Aqueous electrolytes offer a safer, more cost-effective alternative, but their narrow electrochemical window, corrosivity to electrodes, and enabling of dendritic growth on metal anodes limit their practical applications. Water-in-salt electrolytes (WiSEs) have emerged as a promising solution to these challenges. By significantly reducing water activity and forming a stable solid–electrolyte interphase (SEI), WiSEs can expand the electrochemical stability window, inhibit material dissolution, and suppress dendritic growth. This unique SEI formation mechanism, which is similar to that observed in organic electrolytes, contributes to the improved performance and stability of WiSE-based batteries. Additionally, the altered solvation structure of WiSEs minimizes the presence of free water molecules, further stabilizing the SEI and reducing water activity. This review comprehensively examines the composition, mechanisms, and characterization of WiSEs and their application in monovalent-metal-ion batteries. Full article

To fulfil the goals of the circular economy, the treatment of textile wastewater should be focused on the recovery of valuable components. Monovalent anion-selective electrodialysis (MASED) was applied for the separation of reactive dyes from mineral salts. Standard cation-exchange membranes (CM membranes) and monovalent selective anion-exchange membranes (MVA membranes) were used in the electrodialysis (ED) stack. The separation efficiency was evaluated for model solutions of various reactive dyes (varying in molecular weight and chemical reactivity) containing NaCl. In the course of MASED, the mineral salt was successfully removed from the dye solutions with an efficacy of 97.4–99.4%, irrespectively of the composition of the treated solution. The transport of dye molecules through the ion-exchange membranes (IEMs) from diluate to concentrate compartments was irrelevant. Nonetheless, a significant adsorption of dye particles on the membranes was observed. Around 11–40% of the initial dye mass was deposited in the ED stack. Dye adsorption intensity was significantly affected by dye reactivity. This study showed the potential of the MASED process for the separation of the reactive dye from the mineral salt on condition that antifouling membrane properties are improved. The obtained streams (the concentrate rich in mineral salt and the diluate containing the reactive dye) can be reused in the dye-house textile operations; however, some loss of dye mass should be included. Full article

Efficient dye/salt separation poses a great challenge to nanofiltration (NF) membrane technology in the desalting sector of the dye synthesis industry. In this study, we fabricated a novel loose polyester NF membrane via an interfacial polymerization method using “hydroxyl-ammonium” biquaternary diethanolamine (MDET) and trimesoyl chloride. The molecular design of MDET provides a loose crosslinking network, showing high rejection of dyes and the passage of monovalent salt/divalent salt ions in the dye solution, exhibiting exceptional filtration efficiency with high selectivity. Furthermore, the membrane exhibits excellent operational stability for over 100 h, demonstrating superior antifouling properties and high resistance to chlorine. This study provides new insights into the role of dyes and mono- and divalent ions in desalination processes related to the dye synthesis industry. Full article

Background/Objectives: Abiotic stresses such as salinity and drought significantly constrain crop cultivation and affect productivity. Quinoa (Chenopodium quinoa Willd.), a facultative halophyte, exhibits remarkable tolerance to drought and salinity stresses, making it a valued model for understanding stress adaptation mechanisms. The objective of this study was to identify and characterize Sodium/Hydrogen antiporter (NHX) genes from the quinoa genome and study their role in stress tolerance. Methods: We identified and characterized 10 NHX genes from the quinoa genome, which belong to the monovalent cation/proton antiporter 1 (CPA1) superfamily. Comprehensive analysis, including phylogenetic relationships, motif patterns, and structural characteristics, was performed to classify these genes into three subfamilies. Physicochemical properties such as isoelectric point (pI), GRAVY, and transmembrane domains were examined. Promoter analysis was conducted to identify cis-elements linked to abiotic stress responses, phytohormone signalling, and light regulation. qPCR analysis was used to assess the differential expression patterns of CqNHX genes under salt and drought stress. Results: The analysis revealed that the NHX genes were divided into three subfamilies localized to vacuolar, plasma, and endosomal membranes. These genes exhibited structural and functional diversity. Promoter analysis indicated the presence of cis-elements associated with abiotic stress responses, phytohormone signalling, and light regulation, suggesting diverse regulatory roles. qPCR analysis revealed differential expression patterns of CqNHX genes under salt and drought stress, with vacuolar NHXs showing higher induction in leaf tissues under salinity. This underscores their critical role in sodium sequestration and ion homeostasis. Evolutionary analysis indicated a high degree of conservation within subfamilies, alongside evidence of purifying selection. Conclusions: The findings enhance our understanding of the molecular basis of stress tolerance in quinoa and provide valuable targets for genetic engineering to improve crop resilience to environmental challenges. Full article

In this paper, a novel mixed Tutton salt (K_0.86Na_0.14)₂Ni(SO₄)₂(H₂O)₆ was successfully synthesized as a single crystal and evaluated as a thermochemical heat storage material. Its thermal and thermochemical properties were correlated with the structure, which was determined by powder X-ray diffraction using the Le Bail and Rietveld methods. The elemental ratio between the K⁺ and Na⁺ monovalent cations was established by energy-dispersive X-ray spectroscopy. Similar compounds such as Na₂Ni(SO₄)₂(H₂O)₄ and K₂Ni(SO₄)₂(H₂O)₆ were also synthesized and used for structural comparisons. The (K_0.86Na_0.14)₂Ni(SO₄)₂(H₂O)₆ salt crystallizes in monoclinic symmetry with the P2₁/c-space group, typical of hexahydrate crystals from the Tutton salt family. The lattice parameters closely resemble those of K₂Ni(SO₄)₂(H₂O)₆. A comprehensive analysis of the intermolecular contacts, based on Hirshfeld surfaces and 2D fingerprint mappings, revealed that the primary interactions are hydrogen bonds (H···O/O···H) and ion-dipole interactions (K/Na···O/O···Na/K). The unit cell exhibits minimal void space, accounting for only 0.2%, indicative of strong atomic packing. The intermolecular molecular and atomic packing are important factors influencing crystal lattice stabilization and thermal energy supplied to release crystallographic H₂O. The thermal stability of mixed Tutton salt ranges from 300 K to 365 K. Under the dehydration of its six H₂O molecules, the dehydration reaction enthalpy reaches 349.8 kJ/mol, yielding a thermochemical energy storage density of 1.79 GJ/m³. With an H₂O desorption temperature ≤393 K and a high energy storage density ≥1.3 GJ/m³ (criteria established for applications at the domestic level), the (K_0.86Na_0.14)₂Ni(SO₄)₂(H₂O)₆ shows potential as a thermochemical material for small-sized heat batteries. Full article

This work is an effort to mitigate the existing environmental issues caused by brine discharge from Kuwait’s desalination plants and to find an economical and efficient way of managing reject brine from local desalination plants. Low- and high-resistance membranes (LRMs and HRMs, respectively) were used to produce salt and low-salinity water from brine effluent utilizing an electrodialysis (ED)–evaporator hybrid system. The effect of high current densities of 300, 400, and 500 A/m² and brine flowrates of 450 and 500 L/h on the quality of produced salt and diluate were investigated for LRM and HRM. The recovered salt purity for LRM is up to 90.58%. Results show that the low-resistance membrane (LRM) achieved higher water recovery, energy consumption, desalination rate, operation time and ion removal rate than those of the high-resistance membrane (HRM) under the same operating conditions. The difference in concentration for 300 A/m² between LRM and HRM increased from 0.93% at 10 min to 8.28% at 140 min. The difference in diluate concentration effluent is negligible for both membranes, whereas LRM produced higher concentrate effluent than HRM for all current densities and low flowrate (400 L/h). The maximum difference between LRM and HRM (with LRM achieving higher concentrations) is 10.7% for 400 A/m². The permselectivity of LRM for monovalent cations decreased with current density, whereas the effect on permselectivity for HRM was insignificant for the current density values. The addition of a neutral cell was effective in reducing the buildup of divalent ions on the inner membrane of the cathode side. Full article

The application of low-pressure nanofiltration (NF) was investigated for three different applications: water reuse from acid mine drainage (AMD), surface water containing natural organic matter (NOM) and agricultural reuse of microfiltered biologically treated sewage effluent (MF-BTSE). AMD contains many valuable rare earth elements (REEs) and copper (Cu) that can be recovered with fresh water. The NF90 membrane was investigated for recovery of fresh water from synthetic AMD. A steady permeate flux of 15.5 ± 0.2 L/m²h was achieved for pretreated AMD with over 98% solute rejection. NF90 achieved a high dissolved organic carbon (DOC) rejection of 95% from surface water containing NOM where 80% of the organic fraction was hydrophilic, mainly humics. The NF process maintained a high permeate flux of 52 LMH at 4 bars. The MF-BTSE was treated by NTR-729HF for agricultural reuse. NTR-729HF membranes were capable of rejecting DOC and inorganics such as sulfates and divalent ions (SO₄²⁻, Ca²⁺ and Mg²⁺) from MF-BTSE, with less than 20% rejection of monovalent (Na⁺ and Cl⁻) ions. The sodium adsorption ratio (SAR) was significantly reduced from 39 to 14 after treatment through NTR-729HF at 4 bar. The resulting water was found to be suitable to irrigate salt-sensitive crops. Full article

The effect of hydrostatic pressure and cation type on chloride ion transport in marine underwater concrete cannot be ignored. The study of the chloride ion transport behavior of concrete under the effect of hydrostatic pressure and cation type coupling can provide a basis for durability design and the protection of marine concrete. In this work, the chloride ion transport behavior of marine concrete in four common chloride salt solutions under different hydrostatic pressures is studied by a hydrostatic pressure test device developed by the authors. The results show that hydrostatic pressure and its action time significantly influence the chloride ion transport behavior in marine concrete; the higher the hydrostatic pressure of concrete, the faster the chloride ion transport rate. The longer the time, the more chloride ions accumulated in the same position, and the farther the chloride ion transport distance. Cation type has a certain influence on the transport process of chloride ions. Under the same test conditions, the chloride ion transport rate in a divalent cation solution is about 5% higher than that in a monovalent cation solution. The results also show that the chloride ion binding capacity under hydrostatic pressure is only 10~20% of that under natural diffusion. Using the test results, a predictive model of a chloride ion apparent transport coefficient based on the hydrostatic pressure and hydrostatic pressure action time corrected by a cation type influence coefficient is established. Full article

Native potato starch is an excellent carrier of minerals due to its inherent ion exchange capacity. Mineral enrichment not only changes the nutritional value but also influences starch pasting and swelling properties. Hydrothermal treatments like annealing constitute a straightforward and green way to tune functional properties. Here, novel combinations of mineral enrichment and annealing were studied. Ion exchange was readily achieved by suspending starch in a salt solution at room temperature over 3 h and confirmed by ICP-OES. Annealing at 50 °C for 24 h using demineralized water or salt solutions strongly affected pasting, thermal, and swelling properties. The obtained XRD and DSC results support a more ordered structure with relative crystallinity increasing from initially 41.7% to 44.4% and gelatinization onset temperature increasing from 60.39 to 65.94 J/g. Solid-state NMR spectroscopy revealed no detectable changes after annealing. Total digestible starch content decreased after annealing from 8.89 to 7.86 g/100 g. During both ion exchange at room temperature and annealing, monovalent cations promoted swelling and peak viscosity, and divalent cations suppressed peak viscosity through ionic crosslinking. The presented combination allows fine-tuning of pasting behavior, potentially enabling requirements of respective food applications to be met while offering an alternative to chemically modified starches. Full article