Search Results (24)

Coatings based on the eutectic alloy Fe–TiB₂–CrB₂ were obtained by detonation spraying and subjected to pulsed plasma treatment. Comprehensive studies of the microstructure, phase composition, and mechanical and electrochemical properties of the coatings were carried out using SEM, TEM, and XRD methods. The initial coatings are characterized by a typical lamellar structure with interlamellar pores and defects. After pulsed plasma treatment, pronounced compaction of the surface layer, grain refinement, and sealing of interlamellar voids and cracks are observed. The thickness of the modified zone is about 15–30 μm, and the structure becomes fine-grained and more uniform. According to XRD and TEM data, the main boride phases (TiB₂, CrB₂) remain stable, while the intensity of γ-Fe decreases and weak Cr₂₃C₆ peaks appear, indicating phase stabilization and diffusion hardening. After treatment, the microhardness of the near-surface zone increases from ~14 GPa to 17–18 GPa, confirming the strengthening effect. Electrochemical tests showed an increase in corrosion resistance: the corrosion potential shifts to the positive side by approximately 0.15 V, and the corrosion current density decreases by almost two times. Thus, the use of pulsed plasma treatment significantly improves the density, phase stability, hardness, and corrosion resistance of Fe–TiB₂–CrB₂ detonation coatings, making this duplex approach promising for use in conditions of intense wear and exposure to aggressive environments. Full article

Background/Objective: Oligodeoxynucleotides (ODNs) containing base-labile modifications such as N4-acetyldeoxycytidine (4acC), N6-acetyladenosine (6acA), N2-acetylguanosine (2acG), and N4-methyoxycarbonyldeoxycytidine (4mcC) are highly challenging to synthesize because standard ODN synthesis methods require deprotection and cleavage under strongly basic and nucleophilic conditions, and there is a lack of ideal alternative methods to solve the problem. The objective of this work is to explore the capability of the recently developed 1,3-dithian-2-yl-methoxycarbonyl (Dmoc) method for the incorporation of multiple 4acC modifications into a single ODN molecule and the feasibility of using the method for the incorporation of the 6acA, 2acG and 4mcC modifications into ODNs. Methods: The sensitive ODNs were synthesized on an automated solid phase synthesizer using the Dmoc group as the linker and the methyl Dmoc (meDmoc) group for the protection of the exo-amino groups of nucleobases. Deprotection and cleavage were achieved under non-nucleophilic and weakly basic conditions. Results: The 4acC, 6acA, 2acG, and 4mcC were all found to be stable under the mild ODN deprotection and cleavage conditions. Up to four 4acC modifications were able to be incorporated into a single 19-mer ODN molecule. ODNs containing the 6acA, 2acG, and 4mcC modifications were also successfully synthesized. The ODNs were characterized using RP HPLC, capillary electrophoresis, gel electrophoresis and MALDI MS. Conclusions: Among the modified nucleotides, 4acC has been found in nature and proven beneficial to DNA duplex stability. A method for the synthesis of ODNs containing multiple 4acC modifications is expected to find applications in biological studies involving 4acC. Although 6acA, 2acG, and 4mcC have not been found in nature, a synthetic route to ODNs containing them is expected to facilitate projects aimed at studying their biophysical properties as well as their potential for antisense, RNAi, CRISPR, and mRNA therapeutic applications. Full article

The austenitic–martensitic transformation in austenitic–ferritic duplex stainless steel CF8 subjected to cold plastic deformation with a deformation degree ε = 10–95% is studied here using transmission Mössbauer spectroscopy (MS), conversion electron Mössbauer spectroscopy (CEMS), and X-ray diffraction (XRD) methods. It is assumed that the α′-martensite phase appeared at ε > 10%. The CEMS results showed that the formation of α′-martensite occurred most intensively in the near-surface layers of the steel, distributing in depth with the growth of the deformation degree. The volume fraction of the α′-martensite was determined based on the results of calculations carried out via the MS and XRD methods, and a good correlation was observed. A modified Olson–Cohen model was proposed to determine the dependence of the amount of α′-martensite on the deformation degree ε. The coefficients included in the Olson–Cohen expression were found. Full article

The Plasma Immersion Ion Implantation (PIII) nitriding was used to form a modified layer rich in expanded austenite (γ_N) and expanded ferrite (α_N) phases in super duplex steel. The thermal stability of these phases was investigated through the in situ synchrotron X-ray diffraction. All the surfaces were analyzed by SEM, EDS, and nanoindentation. During the heating stage of the thermal treatments, the crystalline structure of the γ_N phase expanded thermally up to a temperature of 350 °C and, above this temperature, a reduction in the lattice parameter was observed due to the diffusion of nitrogen into the substrate. During the isothermal heating, the gradual diffusion of nitrogen continued and the lattice parameter of the γ_N phase decreased. Increasing the treatment temperature from 450 °C to 550 °C, a greater reduction in the lattice parameter of the γ_N phase occured and the peaks related to the CrN, α, and α_N phases became more evident in the diffractograms. This phenomenon is associated with the decomposition of the γ_N phase into CrN + α + α_N. After the heat treatments, the thickness of the modified layers increased and the hardness values close to the surface decreased, according to the diffusion of the nitrogen to the substrate. Full article

Duplex stainless steel is a unique material for cast products, the use of which is possible in various fields. With the same chemical composition, melting, casting and heat treatment technology, pitting and crevice corrosion were observed at the interphase boundaries of non-metallic inclusions and the steel matrix. To increase the cleanliness of steel, it is necessary to carefully select the technology for deoxidizing with titanium or aluminum, as the most common deoxidizers, and the technology for modifying with rare earth metals. In this work, a comprehensive analysis of the thermodynamic data in the literature on the behavior of oxides and sulfides in this highly alloyed system under consideration was performed. Based on this analysis, a thermodynamic model was developed to describe their behavior in liquid and solidified duplex stainless steels. The critical concentrations at which the existence of certain phases is possible during the deoxidation of DSS with titanium, aluminum and modification by rare earth metals, including the simultaneous contribution of lanthanum and cerium, was determined. Experimental ingots were produced, the cleanliness of experimental steels was assessed, and the key metric parameters of non-metallic inclusions were described. In steels deoxidized using titanium, clusters of inclusions with a diameter of 84 microns with a volume fraction of 0.066% were formed, the volume fraction of which was decreased to 0.01% with the subsequent addition of aluminum. The clusters completely disappeared when REMs were added. The reason for this behavior of inclusions was interpreted using thermodynamic modeling and explained by the difference in temperature at which specific types of NMIs begin to form. A comparison of experimental and calculated results showed that the proposed model adequately describes the process of formation of non-metallic inclusions in the steel under consideration and can be used for the development of industrial technology. Full article

Magnetic nanoparticles based on iron oxide attract researchers’ attention due to a wide range of possible applications in biomedicine. As synthesized, most of the magnetic nanoparticles do not form the stable colloidal solutions that are required for the evaluation of their interactions with cells or their efficacy on animal models. For further application in biomedicine, magnetic nanoparticles must be further modified with biocompatible coating. Both the size and shape of magnetic nanoparticles and the chemical composition of the coating have an effect on magnetic nanoparticles’ interactions with living objects. Thus, a universal method for magnetic nanoparticles’ stabilization in water solutions is needed, regardless of how magnetic nanoparticles were initially synthesized. In this paper, we propose the versatile and highly reproducible ligand exchange technique of coating with 3,4-dihydroxiphenylacetic acid (DOPAC), based on the formation of Fe-O bonds with hydroxyl groups of DOPAC leading to the hydrophilization of the magnetic nanoparticles’ surfaces following phase transfer from organic solutions to water. The proposed technique allows for obtaining stable water–colloidal solutions of magnetic nanoparticles with sizes from 21 to 307 nm synthesized by thermal decomposition or coprecipitation techniques. Those stabilized by DOPAC nanoparticles were shown to be efficient in the magnetomechanical actuation of DNA duplexes, drug delivery of doxorubicin to cancer cells, and targeted delivery by conjugation with antibodies. Moreover, the diversity of possible biomedical applications of the resulting nanoparticles was presented. This finding is important in terms of nanoparticle design for various biomedical applications and will reduce nanomedicines manufacturing time, along with difficulties related to comparative studies of magnetic nanoparticles with different magnetic core characteristics. Full article

SAF-2507 super duplex stainless steel powders (SDSS) were prepared using a high-energy planetary ball milling process. The X-ray diffraction (XRD) shows peak broadening after 20 h of ball milling and revealed a phase transformation resulting in a two-phase alloy mixture containing nearly equal amounts of ferrite (α) and austenite (γ). After 20 h of ball milling the particle size was reduced to ~201 nm. Scanning electron microscope (SEM) micrographs showed small-size irregular grains with an average particle size ranging from 5–7 µm. The high-resolution transmission microscope (HRTEM) analysis confirmed the presence of nanocrystalline particles with sizes ranging from 10 to 50 nm. The presence of ferrite phase is visible in the corresponding diffraction pattern as well. In this paper, we have discussed the electrochemical sensor application of mechanically alloyed nano-structured duplex stainless steel powders. The fabricated 4 mg duplex stainless steel modified carbon paste electrode (SDSS-MCPE) has shown excellent current sensitivity in comparison with 2, 6, 8, and 10 mg SDSS-MCPEs during the detection of ascorbic acid (AA) in a phosphate buffer solution with a pH of 6.8. The calculated electrode active surface area of SDSS-MCPE was found to be almost two times larger than the surface area of the bare carbon paste electrode (BCPE). The limit of detection (LD) and limit of quantification (LQ) were found to be 0.206 × 10⁻⁸ M and 0.688 × 10⁻⁸ M, respectively, for the fabricated 4 mg SDSS-MCPE. Full article

The mechanical properties of S32760 duplex stainless steel under dynamic loading conditions at high strain rates are significantly different from those under quasi-static conditions. As a result of large strain, high strain rate, and high temperature, the analysis of the cutting process needs to factor in the influence of the viscous behavior of the material on the plastic deformation process. Based on the viscous effect of the two phases and the mixing rule, a mechanical threshold stress (MTS) constitutive model of S32760 duplex stainless steel considering the viscous effect is established to analyze the effect of strain rate on flow stress. An inverse identification method of the constitutive parameters based on Oxley's theory is proposed. The constitutive parameters of S32760 duplex stainless steel were reversely modified using an equal shear zone model and an orthogonal cutting experiment. The results show that the viscosity of the austenite phase was greater than that of the ferrite phase, and the strain rate had the greatest influence on the viscosity effect in the constitutive model. The prediction error of the constitutive model constructed in this manuscript was less than 4%, which had high accuracy. Full article

Super-duplex stainless steel (SDSS) shows high mechanical and corrosion resistance because of the balanced structure of austenite and ferrite. However, maintaining this phase ratio after welding is a challenge. The use of austenite stabilizing components is recommended to balance the microstructure. The addition of alloying elements presents a challenge because of the characteristics of Nd:YAG pulsed laser welding. An approach, which has proven to be effective, is to use metal electroplating to prepare the surfaces of the mechanical SDSS components that will be welded, therefore promoting the phase balance in the fusion zone. While the effects of metals such as nickel as an austenite stabilizer are well recognized, cobalt’s effects require more research. The present work investigated the influence of the use of cobalt addition in the joining process by preliminary electroplating on UNS S32750 SDSS Nd: YAG pulsed laser welding, specifically regarding microstructure and microhardness. Three conditions were investigated, changing the thickness of the deposited cobalt layer. The addition of cobalt modified the morphology and increased the volume fraction of austenite. An austenite volume fraction of around 48% was obtained using a 35 μm thick cobalt coating. The microhardness was affected by austenite/ferrite proportions. The microhardness dropped from about 375 HV to 345 HV as the cobalt layer’s thickness rose, being similar to that of the base metal. The effect of cobalt as an austenite stabilizer was observed, and the cobalt electroplating technique was effective to correct the phase balance on UNS S32750 laser welding. Full article

The development of chemically modified oligonucleotides enabling robust, sequence-unrestricted recognition of complementary chromosomal DNA regions has been an aspirational goal for scientists for many decades. While several groove-binding or strand-invading probes have been developed towards this end, most enable recognition of DNA only under limited conditions (e.g., homopurine or short mixed-sequence targets, low ionic strength, fully modified probe strands). Invader probes, i.e., DNA duplexes modified with +1 interstrand zippers of intercalator-functionalized nucleotides, are predisposed to recognize DNA targets due to their labile nature and high affinity towards complementary DNA. Here, we set out to gain further insight into the design parameters that impact the thermal denaturation properties and binding affinities of Invader probes. Towards this end, ten Invader probes were designed, and their biophysical properties and binding to model DNA hairpins and chromosomal DNA targets were studied. A Spearman’s rank-order correlation analysis of various parameters was then performed. Densely modified Invader probes were found to result in efficient recognition of chromosomal DNA targets with excellent binding specificity in the context of denaturing or non-denaturing fluorescence in situ hybridization (FISH) experiments. The insight gained from the initial phase of this study informed subsequent probe optimization, which yielded constructs displaying improved recognition of chromosomal DNA targets. The findings from this study will facilitate the design of efficient Invader probes for applications in the life sciences. Full article

Our groups previously reported that conjugation at 3′-end with ursodeoxycholic acid (UDCA) significantly enhanced in vitro exon skipping properties of ASO 51 oligonucleotide targeting the human DMD exon 51. In this study, we designed a series of lipophilic conjugates of ASO 51, to explore the influence of the lipophilic moiety on exon skipping efficiency. To this end, three bile acids and two fatty acids have been derivatized and/or modified and conjugated to ASO 51 by automatized solid phase synthesis. We measured the melting temperature (T_m) of lipophilic conjugates to evaluate their ability to form a stable duplex with the target RNA. The exon skipping efficiency has been evaluated in myogenic cell lines first in presence of a transfection agent, then in gymnotic conditions on a selection of conjugated ASO 51. In the case of 5′-UDC-ASO 51, we also evaluated the influence of PS content on exon skipping efficiency; we found that it performed better exon skipping with full PS linkages. The more efficient compounds in terms of exon skipping were found to be 5′-UDC- and 5′,3′-bis-UDC-ASO 51. Full article

This study discusses the effect of a duplex aging + nitriding process on the wear resistance of an aged double-phase titanium alloy, BT22. Nitriding was applied simultaneously with the heat treatment of the alloy, which is advantageous over the conventional heat and surface treatment methods applied to titanium alloys. According to the results, the thickness of the case depth of the nitrided samples was 40–50 μm. Moreover, nitrogen was uniformly dispersed in the substrate, which was indicated by the hardness tests. The average microhardness of the substrate material was 300 HV_0.01, while the hardness of the top layer was 1190 HV_0.01, which is an almost four-fold increase. The applied duplex treatment substantially affected the wear performance of the tested alloy. For the untreated alloy, the maximum coefficient of friction was 0.8, while in the surface-modified sample, the maximum fluctuations reached 0.6. The abrasive wear process was dominant in the nitrided samples, while delamination and adhesive wear were observed for the untreated specimens. The nitrided alloy exhibited double the wear resistance of the untreated samples. The proposed treatment does not require additional time or energy consumption, providing a substantial technological advantage over conventional methods. Though the alpha case reduces the mechanical performance of titanium, the nitriding of only the component sections intended to withstand friction will have a positive effect. Full article

In this paper, we propose, implement and analyze an Authenticated Encryption with Associated Data Scheme (AEADS) based on the Modified Duplex Construction (MDC) that contains a chaotic compression function (CCF) based on our chaotic neural network revised (CNNR). Unlike the standard duplex construction (SDC), in the MDC there are two phases: the initialization phase and the duplexing phase, each contain a CNNR formed by a neural network with single layer, and followed by a set of non-linear functions. The MDC is implemented with two variants of width, i.e., 512 and 1024 bits. We tested our proposed scheme against the different cryptanalytic attacks. In fact, we evaluated the key and the message sensitivity, the collision resistance analysis and the diffusion effect. Additionally, we tested our proposed AEADS using the different statistical tests such as NIST, Histogram, chi-square, entropy, and correlation analysis. The experimental results obtained on the security performance of the proposed AEADS system are notable and the proposed system can then be used to protect data and authenticate their sources. Full article

The electrochemical behavior of low alloyed Fe-Cr steels with 3 and 5% wt. of Cr in neutral Na₂SO₄ electrolyte combined with a detailed chemical and morphological characterization of these alloys performed by Auger electron spectroscopy, X-ray photoelectron spectroscopy, time-of-flight secondary ion mass spectrometry and scanning electron microscopy are presented here. The corrosion of low alloyed Fe-Cr steels proceeds in the prepassive range, with the formation of corrosion surface films having a duplex structure with outer iron oxide/hydroxide layer and inner Cr oxide-rich layer. The thickness, composition, and the morphology of the surface films vary as a function of chromium content in the alloy as well as conditions of electrochemical tests (temperature). Even a low chromium content shows a beneficial effect on the corrosion performances of the Fe-Cr steels. The chromium as a more active component than iron of ferrite increases the anodic activity of this phase, which results in a rapid saturation of the surface with the anodic reaction products forming a fine crystalline-like and compact layer of corrosion products. In this way, the chromium acts as a modifier of formation/crystallization of the iron-rich surface film (mainly magnetite) in the prepassive range. Full article

The precise site-specific positioning of metal–ligand complexes on various DNA structures through covalent linkages has gained importance in the development of hybrid catalysts for aqueous-phase homogeneous catalysis. Covalently modified double-stranded and G-quadruplex DNA-based hybrid catalysts have been investigated separately. To understand the role of different DNA secondary structures in enantioselective Friedel–Crafts alkylation, a well-known G-quadruplex-forming sequence was covalently modified at different positions. The catalytic performance of this modified DNA strand was studied in the presence and absence of a complementary DNA sequence, resulting in the formation of two different secondary structures, namely duplex and G-quadruplex. Indeed, the secondary structures had a tremendous effect on both the yield and stereoselectivity of the catalyzed reaction. In addition, the position of the modification, the topology of the DNA, the nature of the ligand, and the length of the linker between ligand and DNA were found to modulate the catalytic performance of the hybrid catalysts. Using the optimal linker length, the quadruplexes formed the (−)-enantiomer with up to 65% ee, while the duplex yielded the (+)-enantiomer with up to 62% ee. This study unveils a new and simple way to control the stereochemical outcome of a Friedel–Crafts reaction. Full article