Search Results (287)

Rapid sterility testing of radiopharmaceuticals is essential due to their short half-lives and strict safety requirements. Conventional culture-based methods require several days and are not compatible with clinical workflows. In this work, we present a proof-of-concept droplet-based microfluidic platform for rapid optical detection of bacterial contamination through optical extinction analysis of microdroplets. Monodisperse water-in-oil microdroplets were generated and optically interrogated using a fiber-based detection system. Calibration was first performed using 500 nm polystyrene nanoparticles to establish the relationship between particle concentration and optical extinction. Subsequently, Staphylococcus aureus suspensions were analyzed under aerobic and anaerobic conditions at concentrations ranging from 0 to 230 CFU/mL. The system demonstrated reliable detection of bacterial contamination with estimated limits of detection of ~15 CFU/mL (aerobic) and ~7.5 CFU/mL (anaerobic). The platform enables real-time, high-throughput analysis with minimal sample handling and reduced analysis time compared to conventional sterility tests. This study validates the feasibility of microdroplet-based optical detection as a rapid quality control strategy specifically suited for radiopharmaceutical production, where the short half-lives of common radiotracers impose strict time constraints incompatible with conventional 14-day culture-based sterility tests. The results provide a proof-of-concept foundation for future integration into automated sterility testing workflows, with further validation on real radiopharmaceutical matrices planned as the next step. Full article

The exceptional stability of C-F bonds renders PFAS highly persistent in aqueous environments, posing significant challenges for conventional treatment technologies. While plasma-based technologies show promise, their efficiency is often limited by poor gas–liquid mass transfer in bulk liquid. Here, an in-house constructed ultrasonic atomization–dielectric barrier discharge (UEN-DBD) system was developed to promote PFAS degradation under non-thermal plasma conditions. Ultrasonic atomization generated microdroplets, which promoted PFAS enrichment at the surface of microdroplets and facilitate interactions with plasma-generated reactive species. Using perfluorooctanoic acid (PFOA) and perfluorooctanesulfonate (PFOS) as model compounds, degradation behavior was evaluated over an initial concentration range of 0.01–1.0 ppm. At 0.01 ppm, degradation efficiencies of 96.06% for PFOA and 94.86% for PFOS were achieved within 5 min. Electron paramagnetic resonance (EPR) spectroscopy confirmed the formation of oxidative radicals (·OH) and suggested a mixed redox environment involving reactive species, potentially including superoxide (O₂·⁻) or hydrated electrons (e_aq⁻), in the discharge-treated system. High-resolution mass spectrometry results are consistent with a stepwise chain-shortening pathway dominated by successive –CF₂– scission, while fluoride-release measurements provided supporting evidence for partial defluorination. These findings advance the understanding of plasma-assisted PFAS degradation at the gas–liquid interface and provide a basis for the further development of plasma-assisted PFAS treatment strategies. Full article

Gas atomization is one method for producing fine metal powder. In close-coupled gas atomization, a high-speed gas jet is ejected near the molten metal, and the molten metal is further broken down in the shear layer at the outer edge of the jet, producing fine metal powder of several micrometers to several tens of micrometers. By the way, in close-coupled gas atomization, if the protrusion length of the molten metal nozzle is short, a backflow occurs that goes around the melt delivery nozzle tip and reaches the gas nozzle tip, and the small droplets of molten metal that are atomized at the exit of the melt delivery nozzle are carried by this backflow to the gas nozzle tip, causing it to erode. In this study, we experimentally clarified the existence of the backflow for the first time through measurements of velocity distribution, then the flow state of the gas flow inside the gas atomizer was visualized approximately using the atomized water flow, and the existence of a backflow was confirmed. It was shown that microdroplets of water are carried by the backflow and reach the gas nozzle tip. This was also clarified through numerical analysis results for the air flow. Furthermore, the protrusion length of the melt delivery nozzle at which backflow does not occur was determined, and this was verified in actual gas atomization experiments using molten copper. In addition, the length of the melt delivery nozzle at which backflow does not occur, i.e., the gas nozzle tip does not melt, was found. Furthermore, molten-copper experiments were conducted using this gas atomizer to evaluate its performance. Full article

As a key technology for achieving building heating electrification and decarbonization, the air-source heat pump (ASHP) has long been constrained by outdoor heat exchanger frosting in cold and humid regions. Frosting leads to increased thermal resistance, a sharp rise in air-side pressure drop, and the attenuation of heating capacity, while traditional active defrosting methods, such as reverse-cycle defrosting, suffer from high energy consumption and heating interruption. This review aims to systematically present the recent research progress of superhydrophobic surfaces (SHSs) as a highly efficient passive anti-frosting strategy. First, the complex phase-change dynamics of frosting and key influencing factors such as environment and surface characteristics are deeply analyzed. Second, it elucidates how superhydrophobic surfaces achieve delayed frosting and sloughing off defrosting by delaying nucleation, promoting droplet self-removal, and reducing ice adhesion. Furthermore, fabrication processes suitable for complex fin structures are systematically reviewed from the perspectives of subtractive manufacturing, in situ growth, and additive coatings, and their industrialization prospects are compared. Finally, the practical effects of this technology in improving heat transfer coefficients, reducing fan energy consumption, and improving defrosting efficiency are evaluated. Although superhydrophobic technology has significant energy-saving potential, it still faces challenges such as poor long-term durability, wettability failure under extreme conditions, and residual micro-droplets. Future research should focus on the development of highly durable materials, the matching design of micro–nano structures with macro flow channels, and active–passive synergistic anti-frosting strategies. Full article

Electropolishing is an essential process for the surface treatment of metallic materials. To determine the appropriate replacement timing of electropolishing solutions for their efficient use and improved productivity, it is important to periodically analyze the amounts of dissolved metals in the solutions. However, these solutions are typically highly corrosive, and on-site analytical techniques that can be easily applied at production sites have not yet been established. In this study, we demonstrated microvolume liquid analysis using low-energy laser-induced breakdown spectroscopy (LIBS) combined with a porous silicon substrate fabricated by metal-assisted etching (metal-assisted chemical etching) and a non-contact gas-blowing pretreatment. In the analysis of electropolishing solutions used for niobium superconducting cavities and stainless steel products, emission lines of niobium and of iron and chromium were successfully detected after blowing the respective microdroplet samples on porous silicon, and linear correlations were observed between the spectral line intensity and the polished amounts. The present results provide a basis for future on-site application of LIBS to highly corrosive electropolishing solutions in the metal finishing industry. Full article

High-resolution biofabrication requires precise microscale deposition, yet drop-on-demand (DOD) inkjet bioprinting is constrained by a narrow printable viscosity window. Many biocompatible hydrogel precursors display high zero-shear viscosity and strong shear-thinning, so stable droplet ejection typically requires dilution or reformulation that can compromise the biochemical microenvironment. We present a transient shear-enabled jetting method that exploits intrinsic shear-thinning by using a high-frequency electromagnetic microvalve to deliver short, high-pressure pulses. The resulting localized shear dynamically lowers apparent viscosity in the nozzle region and promotes controlled nucleation, ligament formation, necking, and pinch-off. A coupled, rheology-informed modeling framework (axisymmetric transient CFD, valve dynamics, and electromagnetic FEM) links actuation parameters to droplet volume and stability and guides hardware optimization. Experiments with 2.5% (w/v) sodium alginate validate stable droplet generation and tunable droplet size via stroke length and driving conditions. These results define a practical process window for high-resolution droplet printing of high-viscosity shear-thinning hydrogel inks. Full article

This paper proposes and experimentally validates a label-free microdroplet concentration detector based on a quad-resonator metamaterial. The device exploits the linear relationship between the dielectric constant of a binary mixed solution and its concentration, mapping concentration information to absorption frequency shifts with a sensitivity of 28.53 GHz/RIU. System modeling was performed through full-wave simulation. Experimental results demonstrate a highly linear relationship between resonance frequency shift and concentration across ethanol, water, and ethanol–water solutions. The relative deviation between simulation and measurement is less than 3%, validating the model’s reliability and the robustness of the detection principle. This detector supports rapid non-contact sample replacement without requiring chemical labeling or specialized packaging. It can be mass-produced on standard PDMS substrates, with each unit reusable for >50 cycles. With a single measurement time of <30 s, it meets high-throughput detection demands. Featuring low power consumption, high precision, and scalability, this device holds broad application prospects in point-of-care diagnostics, online process monitoring, and resource-constrained scenarios. Future work will focus on achieving simultaneous multi-component detection via multi-resonator arrays and integrating chip-level wireless readout modules to further enhance portability and system integration. Full article

The high-quality droplet formation in continuous inkjet printing (CIJ) is crucial for precise character deposition on product surfaces. This process, where a piezoelectric transducer perturbs a high-speed ink stream to generate micro-droplets, is highly sensitive to parameters like ink pressure and transducer amplitude. Suboptimal conditions lead to satellite droplet formation and charge transfer issues, adversely affecting print quality and necessitating reliable monitoring. Replacing inefficient manual inspection, this study develops MBSim-YOLO, a deep learning-based method for automated droplet detection. The proposed model enhances the YOLOv8 architecture by integrating MobileNetv3 to reduce computational complexity, a Bidirectional Feature Pyramid Network (BiFPN) for effective multi-scale feature fusion, and a Simple Attention Module (SimAM) to enhance feature representation robustness. A dataset was constructed using images captured by a CCD camera during the droplet ejection process. Experimental results demonstrate that MBSim-YOLO reduces the parameter count by 78.81% compared to the original YOLOv8. At an Intersection over Union (IoU) threshold of 0.5, the model achieved a precision of 98.2%, a recall of 99.1%, and a mean average precision (mAP) of 98.9%. These findings confirm that MBSim-YOLO achieves an optimal balance between high detection accuracy and lightweight performance, offering a viable and efficient solution for real-time, automated quality monitoring in industrial continuous inkjet printing applications. Full article

This study investigates the effects of deposition angle and arc current on the surface morphology and optical response of Ti coatings obtained by unfiltered cathodic arc evaporation for spectrally selective solar-thermal applications. 100 nm-thick Ti films were deposited at normal (0°) and oblique (80°) angles of incidence, with arc currents of 65 A and 90 A, respectively. The SEM measurements revealed the characteristic arc-generated microdroplet population. At normal incidence (0°), droplets are predominantly spherical and relatively uniformly distributed, whereas at 80° incidence, many droplets exhibit elongated footprints aligned with the incoming flux from the Ti cathode. This behavior is consistent with oblique-angle deposition (OAD), where the arrival geometry can promote self-shadowing and transient droplet spreading before solidification. AFM confirms an increase in nanoscale roughness, whereas GIXRD indicates nanocrystalline α-Ti and cubic TiO, with maximum crystallinity for 0°/65 A. Contact-angle measurements demonstrate a transition from hydrophobic 316L (~103°) to moderately hydrophilic Ti-coated surfaces (~68–72°), with only minor dependence on deposition geometry. Optical reflectance in the 400–800 nm range is significantly lower for Ti-coated glass and is further reduced for OAD films, indicating enhanced solar absorptance. Full article

Astaxanthin, one of the most commercially valuable carotenoids, is renowned for its potent antioxidant and anti-inflammatory properties and is experiencing growing demand across diverse industries. To enhance astaxanthin production in Paracoccus marcusii, compound mutagenesis was performed using ethyl methanesulfonate (EMS), ultraviolet (UV) radiation, and atmospheric room temperature plasma (ARTP) treatment. Subsequently, a high-throughput microbial microdroplet culture (MMC) system was employed to select fast-growing microdroplet, followed by screening for high astaxanthin-producing mutants on dual-inhibitor plates. The mutant M21 was isolated and exhibited a significant increase of 16.86% in astaxanthin content (1.53 mg/g) and a 19.81% increase in astaxanthin production (11.71 mg/L) compared with the wild type (WT) (p < 0.05). Moreover, the enhanced phenotype of M21 was genetically stable. Response surface methodology (RSM)-based optimization of fermentation conditions further increased astaxanthin content and production to 1.72 mg/g and 12.92 mg/L, respectively, corresponding to improvements of 16.44% and 23.02% over the WT, while simultaneously reducing culture time, total nitrogen requirements, and sodium lactate consumption, thereby lowering production costs. This study achieved significant enhancement of astaxanthin production through novel mutant breeding and fermentation optimization, underscoring the effectiveness of this integrated strategy for application in industrial biotechnology. Full article

Gallium-based liquid metals have been extensively studied in the field of biomedical engineering, including applications in tumor and inflammatory disease therapy, as well as targeted drug delivery. Among these, leveraging the photothermal effect of gallium liquid metals enables effective treatment of heat-sensitive cells in tumor regions and enhances the diffusion capability of liquid metal microdroplets. However, research on the active treatment of ulcerative colitis (UC) using photothermal therapy with liquid metals remains unexplored. This study focuses on constructing an active composite colloidal motor based on gallium indium liquid metal alloy, using liquid metal microdroplets as the core. Through layer-by-layer assembly of polyelectrolytes, a liquid metal active droplet loaded with the drug mesalazine (5-aminosalicylic acid), named as LMAD-A was developed. Under asymmetric light fields generated by NIR-II light source irradiation, LMAD-A exhibits autonomous locomotion, achieving an effective diffusion coefficient more than 800 times greater than that of Brownian motion in liquid metal microdroplets of similar size. Furthermore, LMAD-A demonstrates phototactic behavior, moving toward the NIR light source autonomously. Through in vitro and in vivo experiments in mice, it was verified that LMAD-A can aggregate, deform, and fuse in the mouse colon under photothermal effects, leading to enhanced release of the loaded drug. In simulated treatments, LMAD-A significantly alleviated DSS-induced colitis in mice, confirming the targeted therapeutic capability of active liquid metal microdroplets as an active therapeutic agent in UC-affected regions. Full article

This review explores the pervasive role of water in generating, storing, and mediating electric charge across natural and artificial systems. Far from being a passive medium, water actively participates in electrostatic and electrochemical processes through its intrinsic ionization, interfacial polarization, and charge separation mechanisms. The Maxwell–Wagner–Sillars (MWS) effect is presented as a unifying framework explaining charge accumulation at air–water, water–ice, and water–solid interfaces, forming dynamic “electric mosaics” across Earth’s environments. The authors integrate diverse phenomena—triboelectricity, hygroelectricity, hydrovoltaic effects, elastoelectricity, and electric-field-driven phase transitions—showing that ambient water continually shapes the planet’s electrical landscape. Electrostatic shielding by humid air and hydrated materials is described, as well as the spontaneous electrification of sliding or dripping water droplets, revealing new pathways for clean energy generation. In addition, the review highlights how electric fields and interfacial charges alter condensation, freezing, and chemical reactivity, underpinning discoveries such as microdroplet chemistry, “on-water” reactions, and spontaneous redox processes producing hydrogen and hydrogen peroxide. Altogether, the paper frames water as a universal electrochemical medium whose interfacial electric imprint influences atmospheric, geological, and biological phenomena while offering novel routes for sustainable technologies based on ambient charge dynamics and water-mediated electrification. Full article

Since individual embryos cannot be evaluated in group culture, establishing a single culture from in vitro maturation to in vitro culture may provide new insights into oocyte and embryo quality. This study aimed to develop a single culture system for individual oocytes, from in vitro maturation through fertilization to embryo development. The effects of curcumin supplementation during in vitro maturation on oocyte maturation, embryo development, and embryo quality were examined in single and group culture systems. Porcine oocytes were cultured individually in 20 µL microdroplets, with one oocyte per droplet, or in groups of 50 oocytes per 500 µL. The maturation medium contained curcumin at concentrations of 20 µM or less. Supplementation with 10 µM curcumin increased oocyte maturation in both systems compared to the controls. The fertilization rates and oocyte/embryo quality did not differ among the treatment groups. Oocytes matured with 10 µM curcumin in a single culture showed a higher blastocyst formation rate (7.0%) than the control (2.3%). In the group culture, 10 µM curcumin increased cleavage rates compared to the control (75.2% vs. 63.0%), but blastocyst formation rates did not differ. Blastocyst formation rates were similar between single and group cultures under control (2.3% and 4.3%, respectively) or 10 µM curcumin (7.0% and 11.4%, respectively) conditions. Therefore, porcine oocytes can develop to the blastocyst stage in a single culture system. Incorporating antioxidants during in vitro maturation may be an effective condition for in vitro embryo culture that can be implemented in a single oocyte. Full article

Monitoring humidity is essential for the protection and long-term preservation of historical monuments and cultural heritage structures, particularly those made of stone, marble, or iron. Excess moisture can accelerate material degradation and compromise structural integrity. This paper presents an alternative, low-cost method for enhancing the sensitivity of a raindrop sensor, aiming to detect micro-droplets such as early morning dew—an important factor in environmental monitoring around such sensitive sites. The proposed method involves covering the sensor’s surface with a fine nylon mesh, such as a stocking, which allows tiny water droplets to accumulate and spread more effectively across the sensor. This modification improves the electrical conductivity between the copper tracks when droplets are present, enabling the sensor to detect moisture levels that would otherwise go unnoticed. Experimental results demonstrate that the modified sensor performs significantly better than the original, unaltered version, offering greater sensitivity and consistency in its readings. The sensor responds more reliably to low volumes of moisture without requiring internal changes to its circuitry, making it both practical and cost-effective. The outcomes of this work are encouraging, suggesting that this approach is suitable for moisture detection in both research and real-world conservation scenarios. It provides a simple and scalable solution for integrating humidity monitoring into broader environmental sensing systems. Full article

Plants play critical roles as nature-based solutions to maintaining air quality and regulating biogeochemical cycles, yet the mechanisms underlying these complex systems remain poorly understood. Hydrogen peroxide (H₂O₂), a globally present atmospheric oxidant, shows well-documented diurnal variation, but no direct link to plant transpiration has previously been reported. This study aimed to determine whether plants can produce exogenous H₂O₂ through transpiration and condensation, thereby revealing a novel pathway by which plants influence proximal and potentially global atmospheric chemistry. To investigate this, we examined a natural plant system undergoing photosynthesis and transpiration; our work was inspired by recent laboratory findings where spontaneous H₂O₂ was generated during the condensation of water vapour into microdroplets in engineered systems. Condensed water collected near leaf surfaces revealed H₂O₂ concentrations of 1–5 ppm, verified using both commercial peroxide test strips and spectrophotometric titration. Importantly, H₂O₂ production occurred only under light conditions when plants were transpiring, while controls without plants or without light showed no detectable levels. A strong distance-dependence was also observed, with minimal to no H₂O₂ detected beyond 40 cm from leaves. These findings suggest that plant-driven formation of water vapour and subsequent condensation produces measurable H₂O₂, establishing a previously unrecognized mechanism with implications for air quality improvement, atmospheric oxidation processes, and climate change modelling and mitigation. Full article