Search Results (40)

Current micro/nanosystems mainly rely on a planar fabrication framework, where structures are built layer-by-layer on flat surfaces. This conventional approach leaves vertical sidewalls underutilized, posing geometric limits in packaging density, three-dimensional (3D) interconnects, and multi-surface functionalization. To overcome these constraints, sidewall patterning has emerged as a promising strategy, enabling 3D integrated circuits, templates for directed nanostructure synthesis, and microfluidic drag reduction. Nevertheless, traditional photolithography and non-photolithographic techniques face challenges when applied to vertical or curved 3D surfaces. Unidirectional radiation and restricted focal depths prevent high-fidelity pattern transfer, even when using soft lithography, scanning probes, or nanoimprinting. To address these geometric and mechanical barriers, our group has developed several approaches for patterning the sidewalls of microsystems, which are the primary focus of this review. Building upon our approaches, this review further surveys related sidewall-patterning strategies, including micro-transfer printing, multi-stimuli-responsive mechanics, block copolymer self-assembly, two-photon polymerization, and laser-induced forward transfer. Collectively, these techniques expand the capabilities of sidewall engineering and provide valuable insights into next-generation 3D micro- and nanomanufacturing. Full article

Micro-structured SAE H13 tool steel inserts for polymer injection molding require accurate replication of sub-millimeter features while retaining adequate densification and heat-treatment response. This study compared two powder-based routes on the same hemispherical insert containing pyramidal features of approximately 0.145 mm base width: hot embossing (HE) of water-atomized SAE H13 powder (supplier d50 = 5.7 µm, irregular morphology) compounded with a commercial M1 binder, and material extrusion (MEX) of a commercial gas-atomized SAE H13 filament processed on a Markforged Metal X. Rheological screening selected a 57:43 vol% powder-to-binder ratio for the in-house HE feedstock, and DSC/TGA measurements defined two-step debinding windows. The best HE conditions were 220 °C, 8 MPa, and 45 min for the in-house mixture, and 210 °C, 8 MPa, and 30 min for the granulated commercial filament; the latter showed a 0.15% linear deviation from the silicone replica diameter among the best-rated samples. Under the tested commercial MEX configuration, the pyramidal features were not resolved because the 0.40 mm deposition line width exceeded the target feature base width, causing the slicer to omit the sub-line-width geometry. The defect populations differed qualitatively: HE specimens showed porosity and local cracking associated with powder morphology and pressureless sintering, whereas MEX specimens showed build-direction-aligned inter-raster voids associated with the toolpath. Microhardness and tensile data are therefore interpreted as process-history-specific results rather than as a direct route ranking, because sintering conditions were not uniform across all specimens. The study defines an experimentally bound process-selection limit for SAE H13 micro-tooling: HE remains preferable for sub-nozzle surface features, whereas MEX remains attractive for macro-scale geometric freedom, if resolution, densification, and post-sintering consolidation are addressed. Full article

This study systematically investigates the effects of manufacturing errors on the drag reduction performance of micro-grooves fabricated using roll-to-roll hot embossing technology. Numerical simulations were conducted to analyze the drag reduction characteristics of spanwise micro-grooves under a 0.4 Ma incoming flow, with a focus on the influence mechanisms of groove array straightness error (δ) and bottom corner rounding error (σ) on aerodynamic performance. The results indicate that straightness errors induce periodic pressure pulsations, which disrupt large-scale turbulent structures and lead to a linear degradation in drag reduction performance. In contrast, bottom corner rounding errors modulate small-scale turbulence by altering the local curvature at the groove bottom. Positive deviations in particular cause an upward shift of the vortex core and enhanced energy dissipation, significantly impairing drag reduction. Based on these findings, an optimized processing window is proposed, recommending that the straightness error δ and bottom corner rounding error σ be controlled within −4% to 2% and −20% to 4%, respectively. Under these conditions, the fluctuation in the drag reduction rate can be confined within 20%. This study provides important theoretical insights and practical guidance for the precision manufacturing of drag-reducing micro-groove surfaces on aircraft. Full article

Icing on aircraft surfaces during operation poses a threat to flight safety. As a passive anti-icing technology, hydrophobic microstructure can achieve long-term anti-icing. In this work, a composite process combining hot-embossing of PVD-coated punches with a low surface energy fluoride-modification scheme is proposed to generate nanoscale cluster structures on hundreds of microns array channels to construct a superhydrophobic micro-nano composite structure. The droplet freezing and frosting behavior of the hydrophobic microstructures was analyzed, and it was found that the anti-icing and anti-frost properties of the microstructure surface improved with an increase in the microstructure period size (T). Compared with the original surface, the freezing time of the microstructure at T = 500 μm was delayed by 214.3% (7 s → 22 s), and the frost layer coverage time was delayed by 75.7% (70 s → 123 s). The maximum water contact angle of the superhydrophobic micro-nano composite structure was 153.3°, and the droplet freezing time was delayed to 95 s, which is a 1166.67% difference, indicating that the multi-stage micro-nano composite structure can significantly improve surface anti-icing performance. The main reason for this result is that the bottom of the microstructure can store air pockets, preventing droplet wetting and heat exchange. Full article

Aluminum alloy surface microstructures possess functional characteristics such as hydrophilicity/hydrophobicity and anti-icing and have important applications in fields such as aerospace and power systems. In order to improve the filling quality of the microstructure and verify the anti-icing property of the microstructure, this work develops a scheme for achieving large-area hot embossing of anti-icing functional microstructures based on a multi-arc ion-plating mold. Compared with conventional steel, the hardness of the PVD-coated steel increases by 44.7%, the friction coefficient decreases by 66.2%, and the wear resistance is significantly enhanced. The PVD-coated punch-assisted embossing could significantly improve filling properties. While the embossing temperature is 300 °C, the PVD-coated punch-assisted embossing can ensure the complete filling of the micro-array channels. In contrast, under-filling defects occur in conventional hot embossing. Then, a large-area micro-channel specimen of 100 cm² was precisely formed without warping, and the average surface roughness Ra was better than 0.8 µm. The maximum freezing fraction of the micro-array channel was reduced by about 53.2% compared with the planar, and the complete freezing time was delayed by 193.3%. The main reason is that the air layer trapped by the hydrophobic structures hinders heat loss at the solid–liquid interface. Full article

This paper presents an experimental study of a novel automated manufacturing process that integrates cold embossing to add complex features, such as micro-Fresnel lens designs, onto a 3D-printed ABS polymer component. The research demonstrates that precise control over process parameters, including embossing time (E_t) and velocity (E_v), is critical for successful feature replication. Gloss analysis confirmed that surface softening as a crucial prerequisite for embossing was successfully achieved using a vapour smoothing (VS) chamber that was developed and optimised for the process. High-speed automation using a 6-axis KUKA robot allowed 48 embosses to be completed in just over one minute, highlighting its efficiency over conventional hot embossing (HE) methods. Results showed that an E_t (0.01 s) prevented feature replication as there was insufficient time to allow for polymer flow, while an optimal E_t (0.1 s) produced high-quality embosses across all test segments. Additionally, this study identified that while insufficient cycle times hinder polymer flow, extended durations can lead to surface hardening, prohibiting replication. These findings pave the way for integrating Diffractive Optical Elements into 3D-printed parts, potentially enhancing precision, functionality, and productivity beyond the capabilities of standard 3D-printing processes. Full article

The development of hydrophobicity on polymer surfaces in mass production is one of the most critical challenges in the plastic industry. This paper deals with a novel combined hot embossing process in which femtosecond laser ablation is utilized to texture the embossing stamps. By controlling the process temperature and axial forces, the laser textures were transferred to polymer surfaces, successfully resulting in hydrophobicity. Four different polymers, including ABS, PP, PA, and PC, along with two different laser textures, namely ball and pyramid, were tested. The laser and hot embossing parameters under which the textures were transferred to the polymers are introduced. The critical micro- and nano-features of the transferred textures that resulted in high hydrophobic contact angles are also discussed. The results indicate that PP and ABS have higher contact angles, respectively, while under the given parameters, PA and PC did not exhibit hydrophobic surfaces. Full article

The roller-to-plate (R2P) hot-embossing process is an effective, low-cost method for producing high-quality micro-/nano-optical components. In the field of night vision applications, the fabrication of chalcogenide glass microstructures is emerging as a promising alternative to traditional infrared glass. This trend is driven by the potential of chalcogenide glass to surpass conventional materials in terms of performance. However, the development of R2P hot embossing faces challenges, such as the high cost of curved mold manufacturing, the reliance on roll-to-roll processes for nano hot embossing, the limitations of plastic materials, and the unclear viscoelastic properties of infrared glass. In this study, a novel R2P hot-embossing process was developed to fabricate flat chalcogenide glass structures. The key parameters, such as roller temperature, speed, and embossing pressure, were investigated to understand their impact on the glass-filling performance. The deformation mechanism of the glass microstructures was also analyzed. The experimental results show that the R2P hot-embossing method offers excellent reproducibility, achieving a maximum filling rate of 96% and an average roughness deviation of 8.36 nm. The increase in the roller temperature and embossing force increased the filling height of the glass microstructure arrays, while an increase in the roller speed decreased the filling height. Different embossing methods, including variations in speed, temperature, and force, are summarized to analyze the structural changes during embossing. This study provides a foundation and a basis for future research on the roller-to-plate hot embossing process. Full article

Hot embossing is a manufacturing technique used to create microchannels on polymer substrates. In recent years, microchannel fabrication technology based on hot embossing has attracted considerable attention due to its convenience and low cost. A new evaluation method of microchannels, as well as an approach to obtaining optimal hot embossing conditions based on the Taguchi method, is proposed in this paper to fabricate precise microchannels for a flexible proton-exchange membrane fuel cell (PEMFC). Our self-made hot embossing system can be used to fabricate assorted types of micro-channel structures on polymer substrates according to various applications, whose bottom width, top width, height and cross-sectional area vary in the aims of different situations. In order to obtain a high effective filling ratio, a new evaluation method is presented based on the four parameters of channel structures, and the Taguchi method is utilized to arrange three main factors (temperature, force and time) affecting the hot embossing in orthogonal arrays, quickly finding the optimal condition for the embossing process. The evaluation method for microchannels proposed in this paper, compared to traditional evaluation methods, incorporates the area factor, providing a more comprehensive assessment of the fabrication completeness of the microchannels. Additionally, it allows for the quick and simple identification of optimal conditions. The experimental results indicate that after determining the optimal embossing temperature, pressure and time using the Taguchi method, the effective filling rate remains above 95%, thereby enhancing the power density. Through variance analysis, it was found that temperature is the most significant factor affecting the hot embossing of microchannels. The high filling rate makes the process suitable for PEMFCs. The results demonstrate that under optimized process conditions, a self-made hot embossing system can effectively fabricate columnar structure microchannels for PEMFCs. Full article

The filling efficiency during the hot embossing process at micro scale is essential for micro-component replication. The presence of the unfilled area is often due to the inadequate behavior law applied to the embossed materials. This research consists of the identification of viscoplastic law (two-layer viscoplastic model) of polymers and the optimization of processing parameters. Mechanical tests have been performed for two polymers at 20 °C and 30 °C above their glass transition temperature. The viscoplastic parameters are characterized based on stress–strain curves from the compression tests. The influences of imposed displacement, temperature, and friction on mold filling are investigated. The processing parameters are optimized to achieving the complete filling of micro cavities. The replication of a micro-structured cavity has been effectuated using this process and the experimental observations validate the results in the simulation, which confirms the efficiency of the proposed numerical approach. Full article

Given the growing importance of lab-on-a-chip in a number of fields, such as medical diagnosis or environmental analysis, the fact that the current fabrication process relies mainly on oil-based polymers raises an ecological concern. As an eco-responsible alternative, we presented, in this article, a manufacturing process for microfluidic devices from chitosan, a bio-sourced, biodegradable, and biocompatible polysaccharide. From chitosan powder, we produced thick and rigid films. To prevent their dissolution and reduce their swelling when in contact with aqueous solutions, we investigated a film neutralization step and characterized the mechanical and physical properties of the resulting films. On these neutralized chitosan films, we compared two micropatterning methods, i.e., hot embossing and mechanical micro-drilling, based on the resolution of microchannels from 100 µm to 1000 µm wide. Then, chitosan films with micro-drilled channels were bonded using a biocompatible dry photoresist on a glass slide or another neutralized chitosan film. Thanks to this protocol, the first functional chitosan microfluidic devices were prepared. While some steps of the fabrication process remain to be improved, these preliminary results pave the way toward a sustainable fabrication of lab-on-a-chip. Full article

Polymethyl methacrylate (PMMA) is a material with good surface wettability and has unique and widespread applications in industrial fields. However, fabricating this material in an environmentally friendly way while maintaining its mechanical robustness remains a challenging task. One effective way is through the rational design of microstructure surfaces. The current study fabricated a pyramid microstructure array on a mold surface using offset-tool-servo flycutting, which was then combined with hot embossing to replicate an inverted pyramid microstructure array on a PMMA surface. Firstly, a toolpath compensation algorithm was developed to linearize the arc toolpath and reduce the cost of ultra-precision lathe. Then, the algorithm was further developed to achieve automatic linear toolpath intersection, aiming to ensure the machining accuracy and improve machining efficiency. An experiment testing the linear toolpath intersecting at 90° was conducted, fabricating a pyramid microstructure array with nanoscale roughness on the mold surface. This surface was then employed for replicating an inverted pyramid microstructure array on the PMMA surface using hot embossing. Furthermore, the accuracy of replication was evaluated, and the experimental results demonstrated excellent replication fidelity, exceeding 98%. The microstructural surface of the PMMA exhibited a change in surface wettability. The wettability test showed a water-droplet contact angle reduction from 84.8° ± 0.1° to 56.2° ± 0.1°, demonstrating a good hydrophilic effect. This study introduces a novel, environmentally friendly and high-precision method to fabricate a functional PMMA surface with an inverted pyramid microstructure array. The results of this study also provide strong technical support and theoretical guidance for micro-nanostructure functional surface machining and replicating. Full article

The fabrication of high-performance microscale devices in substrates with optimal material properties while keeping costs low and maintaining the flexibility to rapidly prototype new designs remains an ongoing challenge in the microfluidics field. To this end, we have fabricated a micro free-flow electrophoresis (µFFE) device in cyclic olefin copolymer (COC) via hot embossing using a PolyJet 3D-printed master mold. A room-temperature cyclohexane vapor bath was used to clarify the device and facilitate solvent-assisted thermal bonding to fully enclose the channels. Device profiling showed 55 µm deep channels with no detectable feature degradation due to solvent exposure. Baseline separation of fluorescein, rhodamine 110, and rhodamine 123, was achieved at 150 V. Limits of detection for these fluorophores were 2 nM, 1 nM, and 10 nM, respectively, and were comparable to previously reported values for glass and 3D-printed devices. Using PolyJet 3D printing in conjunction with hot embossing, the full design cycle, from initial design to production of fully functional COC µFFE devices, could be completed in as little as 6 days without the need for specialized clean room facilities. Replicate COC µFFE devices could be produced from an existing embossing mold in as little as two hours. Full article

As a technology for polymer surface fabrication, roll-to-roll hot embossing has been widely used because of its advantages, such as its low cost and high efficiency. However, the metal micro-mold is a major factor that determines the hot embossing of the polymer. In this study, a new metal micro-mold manufacturing method is proposed. The metal micro-mold is produced using laser shock imprinting (LSI) on the surface of metal foil. It has the characteristics of good thermal stability and high strength. During our LSI experiment, the strength of the mold increased after laser shocking. In this study, copper foils of different thicknesses were selected for LSI experiments. Through the analysis of the profile and forming depth of the microstructure, combined with the numerical simulation of the forming mechanism of copper foils with different thicknesses using ABAQUS software(Abaqus 2021), a copper foil with a flat back was selected as the final metal micro-mold. On this basis, copper molds with different microstructure shapes were created. Then, the mold was used in the hot-embossing experiment to manufacture the microstructure on the surface of polyethylene terephthalate (PET) and to study the fidelity and integrity of the molded microstructure. The deformation resistance of the copper mold under hot-embossing conditions was verified through a nano-indentation experiment. The final results show that the metal micro-mold produced via LSI had a high accuracy and molding stability and has potential applications in the field of roll-to-roll hot embossing. Full article

Freestanding, flexible and open through-hole polymeric micro- and nanostructured membranes were successfully fabricated over large areas (>16 cm²) via solvent removal of sacrificial scaffolds filled with polymer resin by spontaneous capillary flow. Most of the polymeric membranes were obtained through a rapid UV curing processes via cationic or free radical UV polymerisation. Free standing microstructured membranes were fabricated across a range of curable polymer materials, including: EBECRYL3708 (radical UV polymerisation), CUVR1534 (cationic UV polymerisation) UV lacquer, fluorinated perfluoropolyether urethane methacrylate UV resin (MD700), optical adhesive UV resin with high refractive index (NOA84) and medical adhesive UV resin (1161-M). The present method was also extended to make a thermal set polydimethylsiloxane (PDMS) membranes. The pore sizes for the as-fabricated membranes ranged from 100 µm down to 200 nm and membrane thickness could be varied from 100 µm down to 10 µm. Aspect ratios as high as 16.7 were achieved for the 100 µm thick membranes for pore diameters of approximately 6 µm. Wide-area and uniform, open through-hole 30 µm thick membranes with 15 µm pore size were fabricated over 44 × 44 mm² areas. As an application example, arrays of Au nanodots and Pd nanodots, as small as 130 nm, were deposited on Si substrates using a nanoaperture polymer through-hole membrane as a stencil. Full article