Search Results (43)

Extreme surface winds and wave heights of tropical cyclones (TCs)—pose serious threats to coastal community, infrastructure and environments. In recent decades, progress in numerical wave modeling has significantly enhanced the ability to reconstruct and predict wave behavior. This review offers an in-depth overview of TC-related wave modeling utilizing different computational schemes, with a special attention to WAVEWATCH III (WW3) and Simulating Waves Nearshore (SWAN). Due to the complex air–sea interactions during TCs, it is challenging to obtain accurate wind input data and optimize the parameterizations. Substantial spatial and temporal variations in water levels and current patterns occurs when coastal circulation is modulated by varying underwater topography. To explore their influence on waves, this study employs a coupled SWAN and Finite-Volume Community Ocean Model (FVCOM) modeling approach. Additionally, the interplay between wave and sea surface temperature (SST) is investigated by incorporating four key wave-induced forcing through breaking and non-breaking waves, radiation stress, and Stokes drift from WW3 into the Stony Brook Parallel Ocean Model (sbPOM). 20 TC events were analyzed to evaluate the performance of the selected parameterizations of external forcings in WW3 and SWAN. Among different nonlinear wave interaction schemes, Generalized Multiple Discrete Interaction Approximation (GMD) Discrete Interaction Approximation (DIA) and the computationally expensive Wave-Ray Tracing (WRT) A refined drag coefficient (C_d) equation, applied within an upgraded ST6 configuration, reduce significant wave height (SWH) prediction errors and the root mean square error (RMSE) for both SWAN and WW3 wave models. Surface currents and sea level variations notably altered the wave energy and wave height distributions, especially in the area with strong TC-induced oceanic current. Finally, coupling four wave-induced forcings into sbPOM enhanced SST simulation by refining heat flux estimates and promoting vertical mixing. Validation against Argo data showed that the updated sbPOM model achieved an RMSE as low as 1.39 m, with correlation coefficients nearing 0.9881. Full article

Precise temperature control in high-temperature furnaces is challenged by nonlinearities, parameter drift, and high thermal inertia. This study proposes an adaptive control strategy combining a classical PID loop with real-time gain updates from a feed-forward artificial neural network (ANN). Implemented on an 18 kW retrofitted Blue-M furnace, the system was characterized by second-order transfer functions for heating and forced convection cooling. A dataset of 9702 samples was built from eight fixed PID configurations tested under a multi-ramp thermal profile. The selected 3-64-64-32-2 ANN, executed in Python and interfaced with LabVIEW, computes optimal gains in 0.054 ms while preserving real-time monitoring capabilities. Experimental results show that the ANN-assisted PID reduces the mean absolute error to 5.08 °C, limits overshoot to 41% (from 53%), and shortens settling time by 20% compared to the best fixed-gain loop. It also outperforms a fuzzy controller and remains stable under ±5% signal noise. Notably, gain reversals during cooling prevent temperature spikes, improving transient response. Relying on commodity hardware and open-source tools, this approach offers a cost-effective solution for legacy furnace upgrades and provides a replicable model for adaptive control in high-temperature, safety-critical environments like metal processing, battery cycling, and nuclear systems. Full article

This study examines the diffusion of spherical particles in a conical widening channel, with a focus on the effects of deterministic drift and entropic forces. Through numerical simulations, we analyze the motion of particles from a reflecting boundary to an absorbing one. Properties of diffusive motion are explored by inspection of mean squared displacement and mean first passage time. The results show that the diffusion type depends on the drift strength. Without the drift, entropic forces induce effective superdiffusion; however, the increasing drift strength can counterbalance entropic forces and shift the system to standard diffusion and then effective subdiffusion. The mean squared displacement exhibits bending points for high drift values, as predicted by one-dimensional theoretical considerations. The study underscores the importance of considering deterministic and entropic forces in confined geometries. Full article

Air-floating supports are the core component of precision gyroscopes. The precision of their assembly directly determines the degree of gyroscope drift and plays a decisive role in the device’s output precision and service life. Existing air-floating support assembly precision analysis techniques have not yet considered interface deformation, resulting in poor theoretical accuracy and large deviations in actual performance. To address the issue of imprecise predictions in assembly precision for air-floating supports under process loads, this study performs a predictive analysis and impact assessment of assembly precision with uncertainties in the connection process. Firstly, based on bolt elastic interactions, a method for calculating interface assembly deformations is proposed and integrated into a predictive model under process loads. Secondly, numerical computations and assembly deformation tests are carried out to confirm the model’s accuracy. Finally, the distribution law of gyroscope drift is analyzed, considering uncertainty in the connection process. The results show that the maximum deviation of the assembly accuracy prediction model for air-floating supports is less than 5%. Drift in air-floating supports under normally distributed loads shows a skewed normal distribution pattern; the mean drift value decreased sequentially from about 0.03023°/h/g to 0.01995°/h/g, which was reduced by 34% with variation in the dispersion of the pretension force (from 15% to 5%). These findings provide novel insights to enhance assembly precision processes and optimize the fabrication of high-end, complex equipment. Full article

Seismic isolation is a vital strategy for improving the earthquake resilience of structures, utilizing flexible components such as lead–rubber bearings (LRBs) and curved surface sliders (CSSs) to attenuate ground motion effects. This paper presents a comprehensive comparative analysis of seismic isolation design methodologies prescribed in the U.S. code (ASCE 7-22) and the European code (EC8). The focus is on the equivalent lateral force method, also known as the simplified linear method, renowned for its simplicity and efficiency in seismic design applications. A six-story steel building serves as a case study to examine the discrepancies between the two codes. The structure was modeled and subjected to nonlinear time-history analysis (NTHA) using 20 ground motion records, selected and scaled to match a conditional mean spectrum (CMS). Key performance indicators—including displacement at the isolation level, base shear forces, story shear forces, and story drifts—were compared to assess the reliability and effectiveness of each code’s design approach. The findings reveal notable differences between ASCE 7-22 and EC8, particularly in seismic hazard characterization and the calculation of design displacements. ASCE 7-22 generally adopts a more conservative stance, especially for CSSs, resulting in overestimations of design displacements and lateral seismic forces. In contrast, EC8’s simplified method aligns more closely with observed performance for LRBs. However, when applied to CSSs, simplified methods prove less reliable, underscoring the need for more precise analytical techniques. Full article

When a submarine moves near the free surface, the lift and drag characteristics that act on it are different compared to when in deep water; for example, waves on the free surface cause submarine motions that are not seen in deep water conditions and lead to changes in speed, fuel efficiency, safety, and maneuverability. To accurately predict the maneuverability of a submarine, it is necessary to consider how both maneuvering and seakeeping performance are affected by free-surface effects during the design stage. In this study, the unified maneuvering and seakeeping dynamic model is proposed. In the maneuvering performance analysis, hydrodynamic forces in the horizontal plane were calculated using STAR-CCM+. In the seakeeping performance analysis, the 6-DOF motions of the submarine and the mean wave drift forces in the horizontal plane were calculated using Ansys AQWA. Since the maneuvering motion component has a relatively long period and the seakeeping motion component has a relatively short period, the unified maneuvering and seakeeping dynamic model for a submarine moving near the surface was established using a two-time-scale approach. Using the established unified maneuvering and seakeeping dynamic model, turning circle simulations were performed in both calm water and in waves. In calm water, there were no significant differences as depth was varied. However, in irregular waves, significant differences were found in the trajectories and motion variables as depth varied. These findings underscore the necessity of accounting for sea surface conditions when operating near the free surface to ensure safety and avoid potentially hazardous scenarios during submarine operations. Full article

Mean and slowly varying wave loads on floating offshore wind turbines (FOWTs) need to be estimated accurately for the design of mooring systems. The low-frequency drift forces are underestimated by potential flow theory, especially in steep waves. Viscous forces on columns is an important contributor which could be included by adding the quadratic drag of Morison formulation to the potential flow solution. The drag coefficients in Morison equation can be determined based on an empirical formula, CFD study, or model testing. In the WINDMOOR project, a FOWT support structure, composed of three columns joined at the bottom by pontoons and at the top by deck beams, is studied using CFD. In order to extract the KC-dependent drag coefficients, a series of simulations for the fixed structure in regular waves is performed with the CFD code STAR-CCM+. In this study, the forces along each column of the FOWT are analyzed using the results of CFD as well as potential flow simulations. The hydrodynamic interactions between the columns are addressed. A methodology is proposed to process the CFD results of forces on the columns and extract the contribution of viscous effects. Limitations of the Morison drag model to represent extracted viscous forces in steep waves are investigated. The obtained drag coefficients are compared with the available data in the literature. It is shown that accounting for potential flow interactions and nonlinear flow kinematics could, to a large degree, explain the previously reported differences between drag coefficients for a column in waves. Moreover, it is shown that the proposed model can capture the contribution of viscous effects to mean drift forces for fixed columns in waves. Full article

In this work, the seismic response of a multi-story, multi-bay special truss moment frame (STMF) with Ni-Ti shape memory alloys (SMAs) incorporated in the form of X-diagonal braces in the special segment is investigated. The diameter of the SMAs per diagonal in each floor was initially determined, considering the expected ultimate strength of the special segment, developed when the frame reaches its target drift and the desirable collapse mechanism, i.e., the formation of plastic hinges, according to the performance-based plastic design procedure. To further investigate the response of the structure with the SMAs incorporated, half the calculated SMA diameters were introduced. Continuing, three more cases were investigated: the mean value of the SMA diameter was introduced at each floor (case DC1), half the SMA diameter of case DC1 (case DC2), and twice the SMA diameter of case DC1 (case CD3). Dynamic time history analyses under seven benchmark earthquakes were conducted using commercial nonlinear Finite Element software (SeismoStruct 2024). Results were presented in the form of top-displacement time histories, the SMAs force–displacement curves, and maximum inter-story drifts, calculating also maximum SMA displacements. The analysis outcomes highlight the potential of the SMAs to be considered as a novel material in the seismic retrofit of steel structures. Both design approaches presented exhibit a certain amount of effectiveness, depending on the distribution, with the placement of the SMA bars and the seismic excitation considered. Further research is suggested to fully understand the capabilities of the use of SMAs as dissipation devices in steel structures. Full article

Recently, there has been a huge increase in the different ways to manufacture polymer-based sensors. Methods like additive manufacturing, microfluidic preparation, and brush painting are just a few examples of new approaches designed to improve sensor features like self-healing, higher sensitivity, reduced drift over time, and lower hysteresis. That being said, we believe there is still a lot of potential to boost the performance of current sensors by applying modeling, classification, and machine learning techniques. With this approach, final sensor users may benefit from inexpensive computational methods instead of dealing with the already mentioned manufacturing routes. In this study, a total of 96 specimens of two commercial brands of Force Sensing Resistors (FSRs) were characterized under the error metrics of drift and hysteresis; the characterization was performed at multiple input voltages in a tailored test bench. It was found that the output voltage at null force (V_{o_null}) of a given specimen is inversely correlated with its drift error, and, consequently, it is possible to predict the sensor’s performance by performing inexpensive electrical measurements on the sensor before deploying it to the final application. Hysteresis error was also studied in regard to V_{o_null} readings; nonetheless, a relationship between V_{o_null} and hysteresis was not found. However, a classification rule base on k-means clustering method was implemented; the clustering allowed us to distinguish in advance between sensors with high and low hysteresis by relying solely on V_{o_null} readings; the method was successfully implemented on Peratech SP200 sensors, but it could be applied to Interlink FSR402 sensors. With the aim of providing a comprehensive insight of the experimental data, the theoretical foundations of FSRs are also presented and correlated with the introduced modeling/classification techniques. Full article

The strategic recovery of buoys is a critical task in executing deep-sea research missions, as nations extend their exploration of marine territories. This study primarily investigates the dynamics of remotely operated vehicle (ROV)-assisted salvage operations for floating bodies during the recovery of dynamic maritime targets. It focuses on the hydrodynamic coefficients of dual floating bodies in this salvage process. The interaction dynamics of the twin floats are examined using parameters such as the kinematic response amplitude operator (RAO), added mass, damping coefficient, and mean drift force. During the “berthing stage”, when the double floats are at Fr = 0.15–0.18, their roll and yaw Response Amplitude Operators are diminished, resulting in smoother motion. Thus, the optimal berthing speed range for this stage is Fr = 0.15–0.18. During the “side-by-side phase”, the spacing between the ROV and FLOAT under wave action should be approximately 0.4 L to 0.5 L. The coupled motion of twin floating bodies under the influence of following waves can further enhance their stability. The ideal towing speed during the “towing phase” is Fr = 0.2. This research aims to analyze the mutual influence between two floating bodies under wave action. By simulating the coupled motion of dual dynamic targets, we more precisely assess the risks and challenges inherent in salvage operations, thus providing a scientific basis for the design and optimization of salvage strategies. Full article

In order to investigate the hydrodynamic performances of semi-submersible type floating offshore wind turbines (FOWTs), particularly the effect of body-wave-current interaction, the OC4 FOWT is considered in the presence of co-existing regular wave and uniform current fields. The wind loads are not considered at this stage. The problem is treated in the framework of potential-flow theory in the frequency domain, assuming waves of small steepness, and the solution is obtained by using a perturbation expansion method for the diffraction potential with respect to the normalized current speed. Analytical and numerical formulations have been used to treat the inhomogeneous free-surface boundary condition involved in the hydrodynamic problem formulation for the derivation of the associated perturbation potential. The hydrodynamic loads were obtained after evaluating the pressure field around the multi-body configuration using three different computer codes. The results from the three computer codes compare very well with each other and with the numerical predictions of other investigators. Finally, the mean second-order drift forces are calculated by superposing their zero-current values with the corresponding current-dependent first-order corrections, with the latter being evaluated using a ‘heuristic’ approach. Full article

As part of the strategy to achieve net-zero Greenhouse Gas (GHG) emissions in international maritime shipping, there is ongoing exploration into the use of wind propulsion systems as auxiliary ship propulsion devices. When considering a rigid sail as the wind propulsion system, evaluating the performance of a single sail is relatively simple. However, assessing the performance of multiple sails is more challenging due to the interference between the sails and between the sails and the hull. In this study, the thrust characteristics of two rigid sails attached to a ship are investigated by using Computational Fluid Dynamics (CFD). This includes considering the interference effects between the sails themselves and between the sails and the hull. The research reveals the innovative optimized angle of attack for maximizing thrust under tailwind conditions. At 150° in relative wind direction, the best performance is achieved with a low angle of attack on the fore side sail and a high angle of attack on the aft side sail. At 180° in relative wind direction, a high angle of attack on the fore side sail and a low angle of attack on the aft side sail yield the best results. Here, a “low” angle of attack means that the lift force is greater than the drag force, while a “high” angle of attack means the drag force is greater than the lift force. In this study, the force in the ship’s forward direction is only focused on optimizing the angles of attack of the two sails. However, the side forces caused by the sails are also significant for the ship’s sailing conditions. Therefore, future work will involve optimizing the angles of attack under drifting conditions. Full article

This research utilised an open-sourced smoothed particle hydrodynamics (SPH) tool to model and predict the change in wave-induced forces and motions of a free-floating bergy bits approaching a fixed structure in regular waves. Simulation parameters, including particle resolution, fluid viscosity, initial wave condition and boundary treatments, are varied, and their effect on the load imparted to the bergy bit and the structure are investigated. The predicted motions are compared with previously published physical measurements for corresponding scenarios. Both predictions and measurements showed that, in regular waves, the surge motion slowed as the bergy bit approached the structure, and the heave motion increased. For wave loading on bergy bits, the agreement with the experimental data for the root mean square (RMS) force was within 2%. The pressure and velocity fields of the wave–structure–bergy bit interactions are discussed in light of the SPH predictions. This work confirms that the SPH model can accurately capture viscosity–dominated interactions, hydrodynamic damping, and eccentric impact like phenomena and predict both the impact and hydrodynamic loads due to a bergy bit drifting in waves towards a fixed offshore structure. Full article

The effects of four cycles of recurrent selection on the allele frequencies of simple sequence repeat (SSR) markers and population structure were examined in the Maksimir 3 Synthetic (M3S) maize population (Zea mays L.). Genotyping of 32 plants from each selection cycle at 38 SSR loci revealed that the mean number of alleles per locus and the mean expected heterozygosity were preserved across selection cycles, indicating the maintenance of sufficient genetic variability in the population required for future genetic gain. The Waples test of selective neutrality revealed that genetic drift was the main force in changing allele frequencies in the population. The proportion of selectively non-neutral loci in single cycles of selection varied between 16% and 37%. Some non-neutral loci shared the same genomic locations with previously published QTLs controlling important agronomic traits. An analysis of molecular variance revealed that 5.6% of the genetic variation occurred among and 94.4% within cycle populations. Between 5% and 29% of loci were found to be in a significant Hardy–Weinberg (HW) disequilibrium, with the majority showing an excess of homozygosity. The excess of homozygosity at several loci was highly consistent across cycle populations, suggesting positive assortative mating as a possible cause of the observed HW disequilibrium. Linkage disequilibrium (LD) tests revealed that the M3S population was essentially in linkage equilibrium. The proportion of pairs of loci in significant LD varied from 0.1% to 1.8% across selection cycles, probably due to the effects of genetic drift and epistatic selection. Full article

The strong wind-induced current and sea level have influences on the wave distribution in a tropical cyclone (TC). In particular, the wave–current interaction is significant in the period in which the TC passed the mesoscale eddy. In this study, the wave fields of Typhoon Chan-hom (2015) are hindcastly simulated using a coupled oceanic model that utilizes a nested triangle grid, i.e., the finite-volume community ocean model-simulating waves nearshore (FVCOM-SWAVE) model. The forcing wind field is composited from the European Centre for Medium-Range Weather Forecasts (ECMWF) reanalysis data and the simulation using a parametric Holland model, denoted as H-E. The open boundary fields include tide data from TPOX.5 and the hybrid coordinate ocean model (HYCOM) global datasets, including sea surface temperature (SST), sea surface salinity, sea surface current, and sea level data. The simulated oceanic parameters (e.g., the significant wave height, SWH) are validated against the measurements from the Jason-2 altimeter, yielding a root mean square error (RMSE) of 0.58 m for the SWH, a correlation (COR) coefficient of 0.94, and a scatter index (SI) of 0.23. Similarly, the simulated SSTs are compared with the remote sensing products of the remote sensing system (REMSS) and the measurements from Argos, yielding an RMSE of <0.8 °C, a COR of >0.95, and an SI of <0.04. The significant zonal asymmetry of the wave distribution along the typhoon track is observed. The Stokes drift is calculated from the FVCOM-SWAVE simulation results, and then the contribution of the Stokes transport is estimated using the Ekman–Stokes numbers. It is found that the ratio of the Stokes transport to the total net transport can reach >80% near the typhoon center, and the ratio is reduced to approximately <20% away from the typhoon center, indicating that Stokes transport is an essential aspect in the water mixing during a TC. The mesoscale eddies are detected by the sea level anomalies (SLA) fusion data from AVISO. It is found that the significant wave heights, Stokes drift, and Stokes transport inside the eddy area were higher than those outside the eddy area. These parameters inside the cold mesoscale eddies were higher than t inside the warm mesoscale eddies. Otherwise, the SST mainly increased within the cold mesoscale eddies area, while decreased within the warm mesoscale eddies area. The influence of mesoscale eddies on the SST was in proportion to the eddy radius and eddy EKE. Full article