Search Results (69)

T-2 toxin, a type A trichothecene mycotoxin produced by Fusarium species, is widely present in cereals and their processed products, posing a significant contaminant in food safety. To address the food safety challenges caused by this toxin, we established a dual signal enhancement by magnetic separation and split aptamer for ultrasensitive T-2 toxin detection. In this method, the introduction of magnetic graphene oxide (MGO) enhanced signal and increased sensitivity by reducing background interference. The shortened split aptamer reduces non-specific binding to MGO via decreased steric hindrance, thereby facilitating rapid target-induced dissociation and signal generation. A FAM fluorophore-labeled split aptamer probe FAM-SpA1-1 was quenched by MGO. While the fluorescence intensity remained nearly unchanged when the unlabeled split aptamer probe SpA1-2 was introduced alone, a significant fluorescence recovery was observed upon simultaneous addition of SpA1-2 and T-2 toxin. This recovery resulted from the cooperative binding of SpA1-1 and SpA1-2 to T-2 toxin, which distanced the FAM-SpA1-1 probe from MGO. Therefore, the proposed biosensor demonstrated excellent stability, reproducibility, and specificity, with a linear response range of 10–500 pM and a limit of detection (LOD) of 0.83 pM. Satisfactory recovery rates were achieved in spiked wheat (86.0–114.2%) and beer (112.0–129.6%) samples, highlighting the biosensor’s potential for practical applications in real-sample detection. This study establishes the T-2 toxin split aptamer and demonstrates a novel dual-signal enhancement paradigm that pushes the sensitivity frontier of aptamer-based mycotoxin sensors. Full article

Materials with high electron transfer performance remain a key focus in photocatalytic research, as they can effectively promote the separation of photogenerated carriers and enhance the utilization efficiency of photogenerated electrons. To enhance the effective utilization of photogenerated electrons, the MSIG material was prepared by incorporating the iodine clusters and magnetic Fe₃O₄ into the as-synthesized crumpled graphene oxide (CGO) to construct Möbius-like electronic transmission pathways. The introduction of magnetic groups optimized the spin orientation of electrons, facilitating directional electron transport and thereby enhancing the photocatalytic efficiency of the material. Experimental results reveal that, in visible light-driven hydrogen production reactions, the eosin Y (EY)-sensitized Pt-Fe₃O₄-MSIG catalyst exhibits outstanding catalytic performance, with a hydrogen production rate of 1.48 mL/h, which is 15 times higher than that of the Pt-Fe₃O₄ catalyst. Photoelectrochemical analyses show a significant increase in the catalyst’s fluorescence lifetime, attributed to the Möbius strip-like electron transport channels within the material. Theoretical calculations further support this by demonstrating that the bandgap widening of the CGO reduces the recombination probability of photogenerated carriers, thereby improving their average lifetime. This study offers a novel approach for the design of visible-light-driven photocatalytic materials. Full article

Nanocomposites based on Fe₃O₄ and carbonaceous nanoparticles (CNPs), including carbon nanotubes (CNTs) and graphene derivatives (graphene oxide (GO) and reduced graphene oxide (RGO)), such as Fe₃O₄@GO, Fe₃O₄@RGO, and Fe₃O₄@CNT, have demonstrated considerable potential in a number of health applications, including tissue regeneration and innovative cancer treatments such as hyperthermia (HT). This is due to their ability to transport drugs and generate localized heat under the influence of an alternating magnetic field on Fe₃O₄. Despite the promising potential of CNTs and graphene derivatives as drug delivery systems, their use in biological applications is hindered by challenges related to dispersion in physiological media and particle agglomeration. Hence, a solid foundation has been established for the integration of various synthesis techniques for these nanocomposites, with the wet co-precipitation method being the most prevalent. Moreover, the dimensions and morphology of the composite nanoparticles are directly correlated with the value of magnetic saturation, thus influencing the efficiency of the composite in drug delivery and other significant biomedical applications. The current demand for this type of material is related to the loading of a larger quantity of drugs within the hybrid structure of the carrier, with the objective of releasing this amount into the tumor cells. A second demand refers to the biocompatibility of the drug carrier and its capacity to permeate cell membranes, as well as the processes occurring within the drug carriers. The main objective of this paper is to review the synthesis methods used to prepare hybrids based on Fe₃O₄ and CNPs, such as GO, RGO, and CNTs, and to examinate their role in the formation of hybrid nanoparticles and the correlation between their morphology, the dimensions, and optical/magnetic properties. Full article

This study investigated the adsorption properties of graphene oxide in a magnetic-assisted adsorber for the depollution of water containing heavy metals. Two samples of graphene oxide with different surface chemistry were synthetized and assessed using the magnetic-assisted adsorption systems. One graphene oxide sample exhibited a dual magnetic behavior presenting both diamagnetic and ferromagnetic phases, while the other graphene oxide was diamagnetic. The adsorption properties of these graphene oxide samples for removing Pb²⁺ and Cu²⁺ were tested and compared with and without a magnetic field exposure. The results showed that the Pb²⁺ removal increased using both graphene oxide samples in the magnetic-assisted configuration, while Cu²⁺ adsorption was less sensitive to the application of the magnetic field. A monolayer model was used to simulate all the heavy metal adsorption isotherms quantified experimentally. It was concluded that the adsorption mechanism designed to remove Pb²⁺ and Cu²⁺ using tested graphene oxide samples was mainly multi-ionic where two metallic cations could interact with one active site (i.e., oxygenated functional groups) from the adsorbent surface. The oxygenated surface functionalities of graphene oxide samples played a relevant role in determining the impact of magnetic field exposure on the heavy metal removal efficacy. Magnetic-assisted adsorption using graphene oxide is an interesting alternative to reduce the concentration of Pb²⁺ in polluted effluents, and it can also be applied to improve the performance of adsorbents with a limited concentration of oxygenated functional groups, which usually show poor removal of challenging water pollutants such as toxic heavy metals. Full article

Integrating hyperthermia with conventional cancer therapies shows promise in improving treatment efficacy while mitigating their side effects. Nanotechnology-based hyperthermia, particularly using superparamagnetic iron oxide nanoparticles (SPIONs), offers a simplified solution for cancer treatment. In this study, we developed composites of SPION quantum dots (Fe₃O₄) with reduced graphene oxide (Fe₃O₄/RGO) using the coprecipitation method and investigated their potential application in magnetic hyperthermia. The size of Fe₃O₄ nanoparticles was controlled within the quantum dot range (≤10 nm) by varying the synthesis parameters, including reaction time as well as the concentration of ammonia and graphene oxide, where their biocompatibility was further improved with the inclusion of polyethylene glycol (PEG). These nanocomposites exhibited low cytotoxic effects on healthy cells (CHO-K1) over an incubation period of 24 h, though the inclusion of PEG enhanced their biocompatibility for longer incubation periods over 48 h. The Fe₃O₄/RGO composites dispersed in acidic pH buffer (pH 4.66) exhibited considerable heating effects, with the solution temperature increasing by ~10 °C within 5 min of exposure to pulsed magnetic fields, as compared to their dispersions in phosphate buffer and aqueous dimethylsulfoxide solutions. These results demonstrated the feasibility of using quantum dot Fe₃O₄/RGO composites for magnetic hyperthermia-based therapy to treat cancer, with further studies required to systematically optimize their magnetic properties and evaluate their efficacy for in vitro and in vivo applications. Full article

Graphene oxide (GO) nanosheets were functionalized with Schiff base and reduced Schiff base. Covalent and non-covalent functionalized GO nanostructures have been tested for the removal of pesticides with different chemical structures and properties (e.g., Epoxiconazole, Dimethomorph, Cyprodinil, Chlorothalonil, Acetochlor, Trifluralin) from aqueous solutions. The structure and morphology characteristics of the prepared structures were analyzed using techniques such as solid-state nuclear magnetic resonance (SSNMR), Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Results of the experiments showed that, although the non-covalent functionalization did not affect the adsorption properties of GO much, the covalent functionalization increased the adsorption capacity of GO against the mentioned pesticides. Full article

Nanoparticles have been widely applied to treat emulsion-containing wastewater in the form of chemical demulsifiers, such as SiO₂, Fe₃O₄, and graphene oxide (GO). Owing to their asymmetric structures and selective adsorption, Janus nanoparticles show greater application potential in many fields. In the present work, the novel magnetic Janus graphene oxide (MJGO) nanoparticle was successfully prepared by grafting magnetic Fe₃O₄ to the surface of the JGO, and its demulsifying ability to treat a crude oil-in-water emulsion was evaluated. The MJGO structure and its magnetic intensity were verified by Fourier-transform infrared spectra (FTIR), transmission electron microscopy (TEM), X-ray diffraction (XRD), and magnetization saturation (MS) tests. Compared with GO and JGO, MJGO displayed the superior efficiency (>96%) to demulsify the crude oil-in-water emulsion, which can be attributed to the reduced electrostatic repulsion between MJGO and the emulsion droplets. Furthermore, the effects of pH and temperature on the demulsification performance of MJGO were also studied. Lastly, the recyclability of MJGO largely reduced the cost of demulsifiers in separating crude oil and water. The current research presents an efficient and recyclable demulsifier, which provides a new perspective for the structural design of nanomaterials and their application in the field of demulsification. Full article

Core–shell micro/nanomotors have garnered significant interest in biomedicine owing to their versatile task-performing capabilities. However, their effectiveness for photothermal therapy (PTT) still faces challenges because of their poor tumor accumulation, lower light-to-heat conversion, and due to the limited penetration of near-infrared (NIR) light. In this study, we present a novel core–shell micromotor that combines magnetic and photothermal properties. It is synthesized via the template-assisted electrodeposition of iron (Fe) and reduced graphene oxide (rGO) on a microtubular pore-shaped membrane. The resulting Fe-rGO micromotor consists of a core of oval-shaped zero-valent iron nanoparticles with large magnetization. At the same time, the outer layer has a uniform reduced graphene oxide (rGO) topography. Combined, these Fe-rGO core–shell micromotors respond to magnetic forces and near-infrared (NIR) light (1064 nm), achieving a remarkable photothermal conversion efficiency of 78% at a concentration of 434 µg mL⁻¹. They can also carry doxorubicin (DOX) and rapidly release it upon NIR irradiation. Additionally, preliminary results regarding the biocompatibility of these micromotors through in vitro tests on a 3D breast cancer model demonstrate low cytotoxicity and strong accumulation. These promising results suggest that such Fe-rGO core–shell micromotors could hold great potential for combined photothermal therapy. Full article

Efficient thawing can preserve the quality of frozen hairtail (Trichiurus lepturus) close to that of fresh hairtail. In contrast to air thawing (AT) and radio-frequency thawing (RT), this study looked at how graphene oxide (GO) and graphene magnetic (GM) nanoparticles paired with RT affect the microstructure and protein conformation of hairtails after thawing. The results suggested that GM-RT can reduce the myofibrillar protein (MP) damage and be more effective than other thawing treatments, like AT, RT, and GO-RT, in maintaining the microstructure of hairtail. The particle size and zeta potential showed that GM-RT could reduce the aggregation of MP during the thawing process compared to other thawing methods. Moreover, the texture of the hairtail after GM-RT exhibited higher hardness (1185.25 g), elasticity (2.25 mm), and chewiness (5.75 mJ) values compared to other thawing treatments. Especially compared with RT, the GM-RT treatment displayed significant improvements in hardness (27.24%), a considerable increase in springiness (92.23%), and an increase in chewiness (57.96%). GO-RT and GM-RT significantly reduced the centrifugal loss. The scanning electron microscopy results demonstrated that the effect of GM-RT was more akin to that of a fresh sample (FS) and characterized by a well-organized microstructure. In conclusion, GM-RT effectively diminished the MP aggregation and improved the texture of thawed fish. It can be regarded as a viable alternative thawing technique to enhance MP stability, which is vital for preserving meat quality. Full article

Metal-organic frameworks (MOFs)-derived microwave absorbers with tunable components and microstructures show great potential in microwave absorption. Herein, we report a facile thermal reduction approach for synthesizing CoNi alloy/reduced graphene oxide (CoNi/rGO) composites from bimetallic CoNi-MOFs. By tuning the ratio of graphene oxide (GO) in the precursors, the resulting CoNi/rGO-2 composite demonstrates optimal microwave absorption performance with a minimum reflection loss (RL_min) of −66.2 dB at 7.6 GHz in the C band. Moreover, the CoNi/rGO-2 with 50 wt% filler loading achieves a maximum effective absorption bandwidth (EAB) of 6.8 GHz (10.6–17.4 GHz) at a thickness of 2.5 mm, almost spanning the entire Ku band and a portion of the X band. The outstanding performance of CoNi/rGO-2 is ascribed to the high magnetic loss from the CoNi alloy and the incorporation of rGO, which induces interfacial polarization to enhance the dielectric loss and improve the impedance matching of composite. These favorable findings highlight the considerable potential and superiority of the CoNi/rGO-2 composite as an electromagnetic wave absorption material. This work sets forth a viable strategy for designing high-efficiency alloy/rGO absorbers. Full article

(1) Background: Safety problems associated with aflatoxin B₁ (AFB₁) contamination have always been a major threat to human health. Removing AFB₁ through adsorption is considered an attractive remediation technique. (2) Methods: To produce an adsorbent with a high AFB₁ adsorption efficiency, a magnetic reduced graphene oxide composite (Fe₃O₄@rGO) was synthesized using one-step hydrothermal fabrication. Then, the adsorbent was characterized using a series of techniques, such as SEM, TEM, XRD, FT-IR, VSM, and nitrogen adsorption–desorption analysis. Finally, the effects of this nanocomposite on the nutritional components of treated foods, such as vegetable oil and peanut milk, were also examined. (3) Results: The optimal synthesis conditions for Fe₃O₄@rGO were determined to be 200 °C for 6 h. The synthesis temperature significantly affected the adsorption properties of the prepared material due to its effect on the layered structure of graphene and the loading of Fe₃O₄ nanoparticles. The results of various characterizations illustrated that the surface of Fe₃O₄@rGO had a two-dimensional layered nanostructure with many folds and that Fe₃O₄ nanoparticles were distributed uniformly on the surface of the composite material. Moreover, the results of isotherm, kinetic, and thermodynamic analyses indicated that the adsorption of AFB₁ by Fe₃O₄@rGO conformed to the Langmuir model, with a maximum adsorption capacity of 82.64 mg·g⁻¹; the rapid and efficient adsorption of AFB₁ occurred mainly through chemical adsorption via a spontaneous endothermic process. When applied to treat vegetable oil and peanut milk, the prepared material minimized the loss of nutrients and thus preserved food quality. (4) Conclusions: The above findings reveal a promising adsorbent, Fe₃O₄@rGO, with favorable properties for AFB₁ adsorption and potential for food safety applications. Full article

Advanced oxidation processes stand as green alternatives for the decontamination of waste waters. Photocatalysis is an advanced oxidation process in which a semiconductor material absorbs photon energy and triggers redox reactions capable of degrading organic pollutants. Titanium dioxide (TiO₂, titania) represents one of the most popular choices of photocatalytic materials, however the UV-activation of its anatase phase and its high charge recombination rate decrease its photocatalytic activity and weaken its potential. Graphene oxide is a 2D carbon nanomaterial consisting of exfoliated sheets of hexagonally arranged carbons decorated with oxygen- and hydrogen- functional groups. Composite nanomaterials consisting of titania nanoparticles and graphene oxide have proven to enhance the photocatalytic activity of pure TiO₂. In this review, we present a thorough literature review of ternary nanocomposites based on synthesized or commercial titania nanoparticles and GO (or reduced GO) particularly used for the photodegradation of dyes. GO/TiO₂ has been enriched primarily with metals, semiconductors and magnetic nanomaterials, proving a superior dye degradation performance and reusability compared to bare TiO₂. Ongoing challenges and perspectives are outlined. Full article

Nanocomposites based on ferromagnetic nickel nanoparticles and graphene-related materials are actively used in various practical applications such as catalysis, sensors, sorption, etc. Therefore, maintaining their dispersity and homogeneity during deposition onto the reduced graphene oxide substrate surface is of crucial importance to provide the required product characteristics. This paper demonstrates a new, reproducible method for preparing a tailored composite based on nickel nanoparticles on the reduced graphene oxide surface using supercritical isopropanol treatment. It has been shown that when a graphene oxide film with previously incorporated Ni²⁺ salt is treated with isopropanol at supercritical conditions, nickel (2+) is reduced to Ni (0), with simultaneous deoxygenation of the graphene oxide substrate. The resulting composite is a solid film exhibiting magnetic properties. XRD, FTIR, Raman, TEM, and HRTEM methods were used to study all the obtained materials. It was shown that nickel nanoparticles on the surface of the reduced graphene oxide had an average diameter of 27 nm and were gradually distributed on the surface of reduced graphene oxide sheets. The data obtained allowed us to conduct a reconnaissance discussion of the mechanism of composite fabrication in supercritical isopropanol. Full article

Timely diagnosis and appropriate antitumoral treatments remain of utmost importance, since cancer remains a leading cause of death worldwide. Within this context, nanotechnology offers specific benefits in terms of cancer therapy by reducing its adverse effects and guiding drugs to selectively target cancer cells. In this comprehensive review, we have summarized the most relevant novel outcomes in the range of 2010–2023, covering the design and application of nanosystems for cancer therapy. We have established the general requirements for nanoparticles to be used in drug delivery and strategies for their uptake in tumor microenvironment and vasculature, including the reticuloendothelial system uptake and surface functionalization with protein corona. After a brief review of the classes of nanovectors, we have covered different classes of nanoparticles used in cancer therapies. First, the advances in the encapsulation of drugs (such as paclitaxel and fisetin) into nanoliposomes and nanoemulsions are described, as well as their relevance in current clinical trials. Then, polymeric nanoparticles are presented, namely the ones comprising poly lactic-co-glycolic acid, polyethylene glycol (and PEG dilemma) and dendrimers. The relevance of quantum dots in bioimaging is also covered, namely the systems with zinc sulfide and indium phosphide. Afterwards, we have reviewed gold nanoparticles (spheres and anisotropic) and their application in plasmon-induced photothermal therapy. The clinical relevance of iron oxide nanoparticles, such as magnetite and maghemite, has been analyzed in different fields, namely for magnetic resonance imaging, immunotherapy, hyperthermia, and drug delivery. Lastly, we have covered the recent advances in the systems using carbon nanomaterials, namely graphene oxide, carbon nanotubes, fullerenes, and carbon dots. Finally, we have compared the strategies of passive and active targeting of nanoparticles and their relevance in cancer theranostics. This review aims to be a (nano)mark on the ongoing journey towards realizing the remarkable potential of different nanoparticles in the realm of cancer therapeutics. Full article

Wastewater treatment from oil, oil products and organic mixtures is a very relevant topic that can be successfully utilized to solve problems of severe environmental pollution, such as oil spills, industrial oily wastewater discharges and water treatment in the water treatment process. In this work, we have developed new superhydrophobic magnetic polyurethane (PU) sponges, functionalized with reduced graphene oxide (RGO), MgFe₂O₄ nanoparticles, and silicone oil AS 100 (SO), as a selective and reusable sorbent for the purification and separation of wastewater from oil and organic solvents. The surface morphology and wettability of the sponge surface were characterized by scanning electron microscopy (SEM) and a contact angle analysis system, respectively. The results showed that the obtained PU sponge PU/RGO/MgFe₂O₄/SO had excellent mechanical and water-repellent properties, good reusability (lasted more than 20 cycles), as well as fast (immersion time 20 s) and excellent absorption capacity (16.61–44.86 g/g), and additional good magnetic properties, which made it easy to separate the sponge from the water with a magnet. The presence of RGO in the composition of the nanomaterial improves the separating and cleaning properties of the materials and also leads to an increase in the absorption capacity of oil and various organic solvents. The synthesized PU sponge has great potential for practical applications due to its facile fabrication and excellent oil–water separation properties. Full article