Search Results (268)

We have conducted a first-time investigation into the multiferroic properties and band gap behavior of ${\mathrm{CuFeO}}_2$ doped with Al, Ga, and In ions at the Fe site, employing a microscopic model and Green’s function formalism. The tunability of the band gap across a broad energy spectrum highlights the potential of perovskite materials for advanced applications, including photovoltaics, photodetectors, lasers, light-emitting diodes, and high-energy particle sensors. The disparity in ionic radii between the dopant and host ions introduces local lattice distortions, leading to modifications in the exchange interaction parameters. As a result, the influence of ion doping on various properties of ${\mathrm{CuFeO}}_2$ has been elucidated at microscopic level. Our findings indicate that Al doping enhances magnetization and reduces the band gap energy. In contrast, doping with Ga or In results in a decrease in magnetization and an increase in band gap energy. Additionally, it is demonstrated that ferroelectric polarization can be induced either via external magnetic fields or by Al substitution at the Fe site. The theoretical results show good qualitative agreement with experimental data, confirming the validity of the proposed model and method. Full article

The origin of homochirality by rotational magnetoelectrochemistry was theoretically examined. Electrochemical reductions in a rotating solution under a static vertical magnetic field were concluded to yield microscopic vortices with L-activity for enantiomeric reagents, whereas D-active vortices arise from electrochemical oxidation. The reduction case was experimentally verified by rotational magnetoelectrodeposition (RMED) of copper films using an electrolysis cell rotating in a magnetic field, where L-active screw dislocations were created by L-active microscopic vortices. In all the cases of the directions of magnetic polarity and system rotation, the RMED films exhibited L-activity for the enantiomeric reactions of amino acids. Full article

As a contactless physical field, a steady magnetic field (SMF) is capable of acting on substances, which leads to changes in physical and/or chemical properties and to further influencing thermodynamic and kinetic behaviors at macroscopic, mesoscopic, and microscopic scales. The application of the SMF to material science has evolved into an important interdisciplinary field—the Electromagnetic Processing of Materials (EPM). Therein, the implementation of the SMF for the solidification of metals and alloys has been increasingly given attention. The SMF was found to regulate nucleation, crystal growth, the distribution of solutes and structure morphology during alloy solidification via various magnetic effects, such as magnetic damping, the thermoelectric magnetic effect, magnetic orientation and magnetically controlled diffusion. In this review, we briefly summarize the main SMF effects and review recent progress in magnetic field-assisted solidification processing, including nucleation, dendritic growth, solute segregation and interfacial phenomena. Finally, future perspectives regarding controlling alloys’ solidification using an SMF are discussed. Full article

High oil content in breaded fried small yellow croaker (BFYC) was reduced using composite batter gels consisting of tapioca starch, wheat flour, and different concentrations of cassia gum (CG; 0%, 0.2%, 0.4%, 0.6%, 0.8%, 1%). The effects of CG on the oil absorption capacity of BFYC and potential mechanisms were investigated. Dynamic rheological analysis revealed that CG addition could enhance the viscoelasticity of the batter by increasing its storage modulus and loss modulus. Furthermore, FTIR and X-ray diffraction results demonstrated that CG interacts with starch through noncovalent interactions, increasing the relative crystallinity from 9.29% to 16.49%, which promoted the formation of a gel layer. This structural improvement effectively inhibited oil absorption. Differential scanning calorimetry analysis showed that within the 0–0.8% CG range, the batter’s denaturation temperature increased from 78.23 °C to 82.08 °C with higher CG concentrations, indicating prolonged gelatinization and enhanced thermal stability that further reduced oil penetration. Low-field nuclear magnetic resonance analysis revealed that CG increased the proportion of tightly bound and weakly bound water in the batter, thereby improving water retention capacity and reducing moisture loss during frying. Microscopic structural observations and Sudan Red-staining tests confirmed that at 0.8% CG concentration, the crust exhibited the lowest porosity with approximately 40% reduction in surface fat content compared to the control group. In conclusion, CG addition significantly improves batter properties and reduces oil content in fried products, providing theoretical support for the development of low-fat fried foods. Full article

Background: The main mechanism of optic nerve damage in patients with pituitary adenoma (PA) is the pressure of optic chiasm. The retinal nerve fiber layer (RNFL), the ganglion cell layer (GCL)+, and GCL++ thickness measurement by optical coherence tomography (OCT), visual function evaluation, and magnetic resonance imaging (MRI) can be used to predict visual function recovery. In our study, we investigated the associations between visual acuity (VA), visual field (VF), RNFL, GCL changes, and the findings of MRI in patients with PA. Methods: This study was conducted in the Departments of Ophthalmology and Neurosurgery of the Lithuanian University of Health Sciences Hospital. A total of 25 patients diagnosed with PA were included in the study group, and 27 healthy subjects were included in the control group. The thickness of the RNFL and ganglion cell layer (GCL+, GCL++) and optic nerve disc diameter was analysed with OCT. Moreover, an MRI was performed for patients with PA. Results: The RNFL thickness around the optic disk measured preoperatively was reduced significantly in the temporal quadrant in PA patients compared with the control group (median (min; max); mean rank: 73.5 (52; 109); 58.39 vs. 69.5 (16; 168); 46.14; p = 0.038). We found that it was reduced significantly only in the inferior quadrant of the macro-PA group compared to the micro-PA group (median (min; max); mean rank: 99.5 (61; 115); 21.07 vs. 106.5 (90; 121); 32.15), p = 0.008, respectively). The RNFL thickness was reduced significantly only in the inferior quadrant of the non-active PA group compared to the active PA group (median (min; max); mean rank: 118.5 (49; 144); 17.42 vs. 130.5 (77; 156); 28.05), p = 0.028, respectively). RNFL thickness was reduced significantly only in the temporal quadrant in the PA with suprasellar extension group compared to the PA without suprasellar extension group (median (min; max); mean rank: 67.5 (16; 99); 21.66 vs. 72 (58; 168); 30.39), p = 0.036, respectively). Furthermore, GCL++ thickness was reduced significantly in total and in superior and inferior sectors of the PA with suprasellar extension group compared to the PA without suprasellar extension group (median (min; max); mean rank: 98.5 (57; 113); 21.8; 101 (61; 121); 21.48 and 102.5 (59; 116); 21.71 vs. 103.5 (95; 115); 30.2; 106.5 (90; 115); 30.61 and 104.5 (95; 113); 30.32), p = 0.043; p = 0.028 and p = 0.038, respectively). In the control group, significant positive correlations were found between optic disc area and the total RNFL thickness (r = 0.440, p < 0.001). In the PA group, significant correlations were observed between optic rim area and total RNFL thickness (r = 0.493, p < 0.001) and all quadrants, with the strongest in the nasal quadrant (r = 0.503, p < 0.001). A moderate to strong negative correlation was found between visual field (VF) defects and RNFL thickness, with the strongest correlation observed in the superior quadrant. Conclusions: OCT offers a detailed insight into the microscopic structural and functional changes throughout the entire visual pathway in patients with PA. Our findings demonstrate a significant negative correlation between RNFL thickness and visual field defects, highlighting the clinical relevance of OCT measurements in visual function assessment. Moreover, the results suggest that optic rim area may be a more reliable indicator of RNFL thickness variations than optic disc area in patients with PA. Full article

In this study, the effect of aging heat treatment on the superelastic properties and microstructure of [001]-oriented Fe₄₁Ni₂₈Co₁₇Al_11.5Ti_1.25Nb_1.25 (at.%) single crystals was investigated using the cyclic superelastic strain test and a transmission electron microscope (TEM). The TEM results reveal that the average precipitate size is around 3–5 nm in the 600 °C/24 h samples, 6–8 nm in the 600 °C/48 h samples, and 10–12 nm in the 600 °C/72 h samples. The results indicate that precipitate size increases as aging time increases from 24 to 72 h. EDS analysis results show decreased Fe and increased Ni when the analyzed line crosses the precipitate region. The diffraction pattern results show that the precipitate has an L1₂ crystal structure. The thermo-magnetization curves of single crystals under the three aging conditions (600 °C/24 h, 600 °C/48 h, and 600 °C/72 h) show that the values of the transformation temperatures increased from 24 to 72 h. Magnetization was saturated at 140 emu/g under the magnetic field of 7 Tesla. When increasing the magnetic field from 0.05 to 7 Tesla, the transformation temperatures rose. The results indicate that magnetic fields can activate martensitic transformation. From the results of the superelasticity test at room temperature, [001]-oriented FeNiCoAlTiNb single crystals aged at 600 °C for 24, 48, and 72 h presented recoverable strains of 3%, 5.1%, and 2.6%, respectively. Digital image correlation (DIC) results of the aged samples show that two martensite variants were activated during the superelasticity test. The two variants form corresponding variant pairs (CVPs) and improve the recoverable strain of superelasticity. Although maximum recoverable strain was obtained for the 600 °C/48 h samples, the samples show poor cyclic stability at room temperature after applying the 6% strain. According to the DIC results, the retained martensite, which is pinned by dislocations, was observed after the test. The irrecoverable strain was attributed to the residual martensite. For the 600 °C/72 h samples, the large size of the precipitates poses an obstacle to dislocation transformation and formation. The dislocations increase the stress hysteresis width and stabilize the martensite, causing poor recoverability. Full article

Magnetic toroidal multipoles have recently emerged as key descriptors of unconventional cross-correlation phenomena in antiferromagnetic systems. Among them, the rank-2 magnetic toroidal quadrupole, which is characterized as a time-reversal-odd polar tensor, has been theoretically associated with a variety of cross-correlation phenomena arising from the time-reversal symmetry breaking. In this study, we investigate the interplay between magnetic toroidal quadrupoles and electric toroidal dipoles in antiferromagnets, with a particular focus on magnetic field-induced ferroaxiality. Through symmetry analysis and microscopic model calculations, we demonstrate that ferroaxiality can be induced by an external magnetic field, depending on both the field direction and the type of the magnetic toroidal quadrupole. We classify all magnetic point groups that possess magnetic toroidal quadrupoles and identify various candidate materials based on the MAGNDATA database. Our findings reveal a route to coupling spin and lattice degrees of freedom via toroidal multipoles. Full article

Frustrated magnetic systems arising in geometrically constrained lattices represent rich platforms for exploring unconventional phases of matter, including fractional magnetization plateaus, incommensurate orders and complex domain dynamics. However, determining the microscopic spin configurations that stabilize such phases is a key challenge, especially when in-plane and out-of-plane spin components coexist and compete. Here, we combine neutron scattering and magnetic susceptibility experiments with simulations to investigate the emergence of field-induced fractional plateaus and the related criticality in a frustrated magnet holmium tetraboride (HoB₄) that represents the family of rare earth tetraborides that crystalize in a Shastry–Sutherland lattice in the $ab$ plane. We focus on the interplay between classical and quantum criticality near phase boundaries, as well as the role of material defects in the stabilization of the ordered phases. We find that simulations using classical annealing can explain certain observed features in the experimental Laue diffraction and the origin of multiple magnetization plateaus. Our results show that defects and out-of-plane interactions play an important role and can guide the route towards resolving microscopic spin textures in highly frustrated magnets. Full article

To solve the manufacturing problem of the efficient removal of multi-scale surface defects (wrinkles, cracks, scratches, etc.) on the inner wall of MP35N cobalt–chromium alloy vascular stents, this study proposes a collaborative optimization strategy of magnetic abrasive polishing (MAF) based on a new type of magnetic abrasive. In response to the unique requirements for the inner wall processing of high aspect ratio microtubes, metal-based Al₂O₃ magnetic abrasives with superior performance were prepared by the plasma melt powder spraying method. A special MAF system for the inner wall of the bracket was designed and constructed. The four-factor and three-level Box–Behnken response surface method was adopted to analyze the influences and interactions of tube rotational speed, magnetic pole feed rate, abrasive filling amount, and processing clearance on surface roughness (Ra). The significance order of each parameter for Ra is determined as follows: processing clearance > tube rotational speed > abrasive filling amount > magnetic pole feed rate. Using the established model and multiple regression equations, the optimal parameters were determined as follows: a tube rotational speed of 600 r/min, a magnetic pole feed rate of 150 mm/min, an abrasive filling amount of 0.50 g, and a processing clearance of 0.50 mm. The optimized model predicted an Ra value of 0.104 μm, while the average Ra value verified experimentally was 0.107 μm, with the minimum error being 2.9%. Compared with the initial Ra of 0.486 μm, directly measured by the ultra-depth-of-field 3D microscope of model DSX1000, the surface roughness was reduced by 77.98%. MAF effectively eliminates the surface defects and deteriorated layers on the inner wall of MP35N tubes, significantly improving the surface quality, which is of great significance for the subsequent preparation of high-quality vascular stents and their clinical applications. Full article

This research focuses on the development, design, implementation, and testing (with complete hardware and software integration) of a 6D Electromagnetic Actuation (EMA) system for the precise control and navigation of micro/nanorobots (MNRs) in high-viscosity fluids, addressing critical challenges in targeted drug delivery within complex biological environments, such as blood vessels. The primary objective is to overcome limitations in the actuation efficiency, trajectory stability, and accurate path-tracking of MNRs. The EMA system utilizes three controllable orthogonal pairs of Helmholtz coils to generate uniform magnetic fields, which magnetize and steer MNRs in 3D for orientation. Another three controllable orthogonal pairs of Helmholtz coils generate uniform magnetic fields for the precise 3D orientation and steering of MNRs. Additionally, three orthogonal pairs of Maxwell coils generate uniform magnetic field gradients, enabling efficient propulsion in dynamic 3D fluidic environments in real time. This hardware configuration is complemented by three high-resolution digital microscopes that provide real-time visual feedback, enable the dynamic tracking of MNRs, and facilitate an effective closed-loop control mechanism. The implemented closed-loop control technique aimed to enhance trajectory accuracy, minimize deviations, and ensure the stable movement of MNRs along predefined paths. The system’s functionality, operation, and performance were tested and verified through various experiments, focusing on hardware, software integration, and the control algorithm. The experimental results show the developed system’s ability to activate MNRs of different sizes (1 mm and 0.5 mm) along selected desired trajectories. Additionally, the EMA system can stably position the MNR at any point within the 3D fluidic environment, effectively counteracting gravitational forces while adhering to established safety standards for electromagnetic exposure to ensure biocompatibility and regulatory compliance. Full article

Pore structure plays a critical role in evaluating shale “sweet spots”. Compared to marine shale, lacustrine shale has more diverse lithofacies types and greater heterogeneity in pore structure due to frequently changing environmental conditions. Using methods such as mercury intrusion porosimetry (MIP), field emission scanning electron microscopy (FE-SEM), nuclear magnetic resonance (NMR), and X-ray diffraction (XRD), this study investigates the micropore structures and heterogeneity of different lithofacies in the Jurassic Dongyuemiao Member lacustrine shale. Image processing and multifractal theory were employed to identify the controlling factors of pore structure heterogeneity. The key findings are as follows. (1) Based on mineral content and laminae types, the lithofacies types of Dongyuemiao lacustrine shale are classified into four types: shell–laminae mixed shale (SLMS), silty–laminae clay shale (SLCS), clast–laminae clay shale (CLCS), and clay shale (CS). (2) Based on genesis, shale reservoirs’ pore and permeability space are categorized into inorganic pores, organic pores, and micro-fractures. Inorganic pores consist of inter-particle pores and intra-particle pores. Pore size distribution curves for all four lithofacies exhibit two main peaks, with pore sizes concentrated in the ranges of 2–10 nm and 50–80 nm. Mesopores and macropores dominate, accounting for over 80% of the total pore volume. Mesopores are most developed in CLCS, representing 56.3%. (3) Quartz content is positively correlated with the multifractal dimension, while clay content shows a negative correlation. Higher quartz content, coupled with lower clay content, weakens pore structure heterogeneity. A negative correlation exists between total organic carbon (TOC) and the multifractal dimension, indicating that higher organic matter content enhances organic pore development and increases microscopic heterogeneity. (4) Porosity heterogeneity in SLMS is effectively characterized by D₀-D_max, while in the other three lithofacies, it is characterized by D_min-D₀. Permeability across all lithofacies correlates with D₀-D_max. In CS, SLMS, and SLCS, permeability is positively correlated with D₀-D_max, with higher values indicating greater permeability heterogeneity. In CLCS, permeability is negatively correlated with D₀-D_max, such that lower values reflect stronger heterogeneity. Full article

The pore structure of reservoir rocks was a crucial factor affecting hydrocarbon production. Accurately characterized the micropore structure of different types of rock reservoirs was of great significance for unconventional natural gas exploration. In this study, multiple observation methods (field emission scanning electron microscope (FESEM) and low-field nuclear magnetic resonance (LFNMR)) and physical tests (mercury injection capillary pressure (MICP)) were employed, and double logarithmic plots for fractal fitting were illustrated. The fractal dimension of 15 samples was calculated using fractal theory to systematically investigate the pore–fracture structure and fractal characteristics of hydrocarbon source rock (limestone, mudstone, and sandstone) samples from the Late Carboniferous Taiyuan Formation in the Huainan coalfield. MICP experiments revealed that sandstone reservoirs had larger and more uniformly distributed pore throats compared to mudstone and limestone, exhibiting superior connectivity and permeability. The T₂ spectrum characteristic maps obtained using LFNMR were also consistent with the pore distribution patterns derived from MICP experiments, particularly showed that sandstone types exhibited excellent signal intensity across different relaxation time periods and had a broader T₂ spectrum width, which fully indicated that sandstone types possess superior pore structures and higher connectivity. FESEM experiments demonstrated that sandstone pores were highly developed and uniform, with sandstone fractures dominated by large fractures above the micrometer scale. Meanwhile, the FESEM fractal dimension results indicated that sandstone exhibits good fractal characteristics, validating its certain oil storage capacity. Furthermore, the FESEM fractal dimension exhibited a good correlation with the porosity and permeability of the hydrocarbon source rock reservoirs, suggesting that the FESEM fractal dimension can serve as an important parameter for evaluating the physical properties of hydrocarbon source rock reservoirs. This study enriched the basic geological theories for unconventional natural gas exploration in deep coal-bearing strata in the Huainan coalfield. Full article

We improved a scanning magnetic microscope built previously by adding a new detection system and the capability of mapping samples applying magnetic fields from −500 mT to +500 mT. The mechanical structure was also enhanced to decrease vibrations of the system in the earth’s magnetic field. The microscope is based on a differential arrangement of two Hall effect elements. The overall system presented a sensitivity of about 850 $n{T}_{rms}\surd Hz$, and it was calibrated using a 99% pure nickel sphere. The system achieved a magnetic moment sensitivity of the order of 10 nAm². All equipment used for operating the magnetic microscope was controlled by using the LabVIEW^® platform. We also fabricated samples with controlled properties using iron oxide microparticles and epoxy resin with various densities. We obtained the magnetization curves of the composites using the assembled microscope and compared them with the iron oxide powder. Full article

The ionic soil stabilizer (ISS) can synergistically enhance the mechanical properties and improve the engineering characteristics of iron tailings soil in conjunction with cementitious materials such as cement. In this paper, the influence of ISS on the cement hydration process and the charge repulsion between iron tailings soil particles was studied. By means of Isothermal calorimetry, X-ray diffraction (XRD), Scanning electron microscope (SEM), and Low-field nuclear magnetic resonance microscopic analysis methods such as (LF-NMR), X-ray photoelectron spectroscopy (XPS), Non-evaporable water content and Zeta potential were used to clarify the mechanism of ISS-enhanced cement stabilization of the mechanical properties of iron tailings soil. The results show that in the cement system, ISS weakens the mechanical properties of cement mortar. When ISS content is 1.67%, the 7 d compressive strength of cement mortar decreases by 59.8% compared with the reference group. This retardation arises due to carboxyl in ISS forming complexes with Ca²⁺, creating a barrier on cement particle surfaces, hindering the hydration reaction of the cement. In the cement-stabilized iron tailings soil system, ISS has a positive modification effect. At 0.33% ISS, compared with the reference group, the maximum dry density of the samples increased by 6.5%, the 7 d unconfined compressive strength increased by 35.3%, and the porosity decreased from 13.58% to 11.85%. This is because ISS reduces the double electric layer structure on the surface of iron tailings soil particles, reduces the electrostatic repulsion between particles, and increases the compactness of cement-stabilized iron tailings soil. In addition, the contact area between cement particles increases, the reaction energy barrier height decreases, the formation of Ca(COOH)₂ reduces, and the retarding effect on hydration weakens. Consequently, ISS exerts a beneficial effect on augmenting the mechanical performance of cement-stabilized iron tailings soil. Full article

In recent decades, magnetic hyperthermia (MH) has gained considerable scientific interest in cancer treatment due to its ability to heat tumor tissues deeply localized inside the body. Functionalizing magnetic nanoparticles (MNPs) with vector molecules via specific organic molecules that coat the particle surface has enabled targeting particular tissues, thereby increasing the specificity of MH. MH relies on applying radiofrequency (RF) magnetic fields to a magnetic nanoparticle distribution injected in a tumor tissue. The RF field energy is converted into thermal energy through specific relaxation mechanisms and magnetic hysteresis-driven processes. This increases the tumor tissue temperature over the physiological threshold, triggering a series of cellular apoptosis processes. Additionally, the mechanical effects of low-frequency AC fields on anisotropic MNPs have been shown to be highly effective in disrupting the functional cellular components. From the macroscopic perspective, a crucial parameter measuring the efficiency of magnetic nanoparticle systems in MH is the specific absorption rate (SAR). This parameter is experimentally evaluated by different calorimetric and magnetic techniques and methodologies, which have specific drawbacks and may induce significant errors. From a microscopic perspective, MH relies on localized thermal and kinetic effects in the nanoparticle proximity environment. Studying MH at the cellular level has become a focused research topic in the last decade. In the context of these two perspectives, inevitable questions arise: could the thermal and kinetic effects exhibited at the cellular scale be linked by the macroscopic SAR parameter, or should we find new formulas for quantifying them? The present work offers a general perspective of MH, highlighting the experimental pitfalls encountered in SAR evaluation and motivating the necessity of standardizing the devices and protocols involved. It also discusses the challenges that arise in MH performance evaluation at the cellular level. Full article