Search Results (48)

This study investigates the impact of sulphuric acid concentration (40% vs. 60%) on the extraction of cellulose nanocrystals (CNCs) from alkali-treated sugarcane bagasse (SCB) and their reinforcement in poly(furfuryl) alcohol (PFA) composites. Probing into the physicochemical changes through scanning electron microscopy (SEM) displayed drastic morphological changes, alkali removal of noncellulosic components followed by sulphuric acid hydrolysis further refined cellulose to nanoscale morphologies. The X-ray diffraction (XRD) study showed that after alkali treatment, the crystallinity was significantly higher (65%), and the crystallinity index of CNCs prepared from 40% H₂SO₄ was greater than the CNCs prepared from 60% H₂SO₄ (61%). Fourier transform infrared spectral and thermogravimetric analysis (TGA) suggested that improving the polymeric performance by the incorporation of a CNC resulted in a decrease in the thermal stability of the modified polyelectrolyte, which was largely attributed to higher sulphate esterification achieved at higher acid concentrations. It is possible to use CNCs to achieve higher mechanical performance while also indicating that optimizing thermal properties and mechanical performance of high-performance materials will require an improved understanding of the microstructural parameters governing the polymer–filler interface. This work demonstrates that acid concentration critically balances CNC crystallinity and thermal performance, offering insights for optimizing sustainable nanocomposites. Full article

Biocomposites, made from biobased polymers with natural fibre reinforcement, offer a feasible path towards environment friendly and sustainable materials. However, biocomposites have struggled to attract ta market that is mostly dominated by conventional fossil-based polymers. To increase the cost efficiency and extend the lifespan of biocomposites, the effects of mechanical recycling on their properties should be thoroughly explored. While there has been some research on recycling natural fibre-reinforced biocomposites, limited attention has been paid to biocomposites reinforced with softwood fibre. This study investigates the impact of mechanical recycling on poly-lactic acid (PLA) biocomposites reinforced with bleached and unbleached softwood kraft pulp fibres at 15 wt% and 30 wt%. The results show that single-stage mechanical recycling improves Young’s modulus by 11–13% while maintaining impact strength. Tensile strength remains stable for biocomposites with 15 wt% fibre but decreases by 6–8% for with 30 wt% biocomposites. Recycling improves fibre dispersion by reducing agglomeration but leads to PLA degradation, which could potentially be mitigated by adding virgin polymer or chain extenders. These findings highlight the potential for reusing PLA-softwood fibre biocomposites while emphasizing the need for further research into multiple recycling cycles. Full article

Bioresources have been gaining popularity due to their abundance, renewability, and recyclability. Nevertheless, given their diverse composition and complex hierarchical structures, these bio-based sources must be carefully processed to effectively extract valuable raw polymeric materials suitable for producing man-made organic fibres. This review will first highlight the most relevant bio-based sources, with a particular focus on promising unconventional biomass sources (terrestrial vegetables, aquatic vegetables, fungi, and insects), as well as agroforestry and industrial biowaste (food, paper/wood, and textile). For each source, typical applications and the biopolymers usually extracted will also be outlined. Furthermore, acknowledging the challenging lignocellulosic structure and composition of these sources, an overview of conventional and emerging pre-treatments and extraction methods, namely physical, chemical, physicochemical, and biological methodologies, will also be presented. Additionally, this review aims to explore the applications of the compounds obtained in the production of man-made organic fibres (MMOFs). A brief description of their evolution and their distinct properties will be described, as well as the most prominent commercial MMOFs currently available. Ultimately, this review concludes with future perspectives concerning the pursuit of greener and sustainable polymeric sources, as well as effective extraction processes. The potential and main challenges of implementing these sources in the production of alternative man-made organic fibres for diverse applications will also be highlighted. Full article

PLA biocomposites, incorporating 5% wt. of lignocellulosic fibres (LF) from Posidonia oceanica waste with different degrees of cellulose purification, were obtained by melt blending and compression moulding. The LF were obtained after removing part of the non-cellulosic components by subcritical water extraction at 150 and 170 °C and after bleaching the extracted residues with hydrogen peroxide or sodium chlorite. The non-bleached LF provided the composites with a brown colour and opacity, while the bleached LF impacted the optical properties of composites to a lower extent, depending on their whiteness. The LF composition had a noticeable effect on the composites’ mechanical and barrier properties. All LF reduced the water vapour barrier capacity while promoting the oxygen barrier of the films. Bleached LF enhanced the film stiffness and reduced extensibility and resistance to break, whereas non-bleached LF had lower impacts on the tensile parameters. Considering the mechanical and barrier performance of the composites, the fibres obtained at 170 °C and bleached with sodium chlorite exhibited the best behaviour. Nevertheless, if transparency and colour are not limiting for the use of the films, untreated LF allowed for good preservation of the water vapour permeability of PLA films and enhanced the oxygen barrier capacity, with a similar mechanical response as the other non-bleached fractions. Full article

The fashion industry significantly impacts the environment, mainly through the substantial generation of waste textiles fostered by fast fashion business models. This study introduces an innovative approach to textile waste management by recycling waste textiles without the use of chemical or mechanical treatments. Herein, we developed a method adhering to the principles of circular economy to transform these textile wastes into high-quality construction panels using a papermaking process. This method not only provides a sustainable solution to reduce landfill dependency but also enhances resource efficiency in the construction industry. The fabricated panels, composed of a blend of 45% textile waste microfibres and 55% fire-retardant fibres, exhibit several advantageous properties. They feature a low apparent density ranging between 170–180 kg/m³ and a low thermal conductivity coefficient of 0.047 W/m∗K at 50 kPa. It revealed that phosphorylated fibres not only provide flame-retardant properties, but they also significantly improve the mechanical properties of the panels. For example, load at break increases from 12.4 to 81.1 N, stress at break from 0.44 to 3.59 MPa, and E-modulus from 29.2 to 198.8 MPa after the addition of these 55% fibres. Moreover, these panels successfully met the criteria set by international standards for construction products satisfying the fire test, EN ISO 11925-2. These characteristics make the panels superior options for sustainable construction materials, offering enhanced fire resistance and insulation properties, which are critical to meet modern building standards. They mark a pivotal step towards sustainable construction and waste reduction in the fashion industry. Full article

Grape stalks (GSs) from winemaking were submitted to a green process to valorise its lignocellulosic biomass that applied subcritical water extraction (SWE) at 170 °C and 180 °C to obtain active extracts and cellulose-enriched fractions. The sum of the total phenolic content of the soluble extract and the solid residue fractions from the SWE exceeded that of the GS, which suggests the generation of compounds with antioxidant properties through SWE. All SWE fractions showed high antioxidant power. The increased temperature promoted the extraction of polyphenolic compounds, enhancing the antioxidant power of both extracts and solid residues. These solid residue fractions were bleached with alkaline hydrogen peroxide solutions (4 and 8% v/v) to purify cellulose. After two bleaching cycles, no notable delignification progress was observed, as the bleaching yield or whiteness index did not significantly change in the further cycles. The first bleaching cycle led to a significant reduction in the lignin content at both SWE temperatures. The cellulose purity was higher in the samples obtained at 170 °C and bleached with 4% alkaline hydrogen peroxide. SWE at 180 °C led to greater cellulose oxidation during the bleaching step regardless of the hydrogen peroxide concentration. Full article

Wood–plastic composites (WPCs) combine the properties of plastics and lignocellulosic fillers. A particular limitation in their use is usually a hydrophobic, poorly wettable surface. The surface properties of materials can be modified using ion implantation. The research involved using composites based on polyethylene (PE) filled with sawdust or bark (40%, 50%, and 60%). Their surfaces were modified by argon ion implantation in three fluencies (1 × 10¹⁵, 1 × 10¹⁶, and 1 × 10¹⁷ cm⁻²) at an accelerating voltage of 60 kV. Changes in the wettability, surface energy, and surface colour of the WPCs were analysed. It was shown that argon ion implantation affects the distinct colour change in the WPC surface. The nature of the colour changes depends on the filler used. Implantation also affects the colour balance between the individual variants. Implantation of the WPC surface with argon ions resulted in a decrease in the wetting angle. In most of the variants tested, the most significant effect on the wetting angle changes was the ion fluence of 1 × 10¹⁷ cm⁻². Implantation of the WPC surface also increased the surface free energy of the composites. The highest surface free energy values were also recorded for the argon ion fluence of 1 × 10¹⁷ cm⁻². Full article

There has been a growing interest in recycling and upcycling different waste streams due to concerns for environmental protection. This has prompted the desire to develop circular economies and optimize the utilization of bioresources for different industrial sectors. Turning agricultural and forestry waste streams into high-performance materials is a promising and meaningful strategy for creating value-added materials. Lignocellulose fibres from plants are emerging as a potential candidate for eco-friendly feedstock in the textile industry. Nonwoven fabric is one of the most innovative and promising categories for the textile industry since it currently utilizes about 66% synthetic materials. In the upcoming wave of nonwoven products, we can expect an increased utilization of natural and renewable materials, particularly with a focus on incorporating lignocellulosic materials as both binders and fibre components. The introduction of low-cost fibres from waste residue materials to produce high-performance nonwoven fabrics represents a shift towards more environmentally sustainable paradigms in various applications and they represent ecological and inexpensive alternatives to conventional petroleum-derived materials. Here, we review potential technologies for using agricultural waste fibres in nonwoven products. Full article

Biofibres’ wide application in mortar enhancement has thus far been restricted by factors related to their chemical composition and hygroscopic nature. Their hydrophilic behaviour increases the water demand of mortar mixtures and diminishes their affinity to the matrix, while further moisture-related fibre degradation issues may arise. Additionally, natural fibres seem to be susceptible to degradation caused by exposure to alkaline environmental conditions such as those experienced by cement mortars, restricting their utilisation in the construction industry. Therefore, the current study investigates the potential of fibre modification through treatments that would permanently alter their structure and chemical composition to improve their performance. In this study, wood fibres of black pine and beech species were exposed to mild thermal treatment (140 °C 2 h, under a steam atmosphere), characterised in terms of the physical and chemical properties and incorporated in cement mortars, applying the proportion of 1.5% v/v in the mortar, in order to assess their performance as reinforcement material. The mortars’ workability (at a fresh state) was examined, as well as other physical, hygroscopic, thermal, and mechanical characteristics of the mortars at the ages of 28, 90 and 365 days and weathering performance, by subjecting them to different artificial ageing environments (freeze–thaw cycles or outdoor exposure). The results revealed the beneficial role of the treated fibres in dimensional stability, flexural strength, thermal insulation properties and capillary absorption of the mortar specimens, especially during the ageing process, with the black pine fibres showing the greatest improvement. The hydrothermally treated wood fibres seem to help maintain the integrity of cement mortars under all ageing conditions, proving that they could provide low-cost and eco-friendly mortar enhancement pathways. Full article

Hemp (Cannabis sativa) stalk fibres from industry residues were incorporated into polybutylene adipate terephthalate, a synthetic biodegradable polyester, to produce films and paper coatings. The lignocellulosic components and the chemical composition of the fibres were analysed, and the results highlight the bioactivity due to cannabinoids, alkanoids, and lignin, among others, making the fibres attractive for active food packaging. The incorporation, without chemical modification, of 2% (w/w) hemp in the PBAT matrix increased the water vapour permeability of PBAT around 22%. The impact on mechanical properties was determined, and the results show that the PBAT/hemp film is less stretchable but stronger than the pure PBAT film. The incorporation of hemp enhanced significantly the compostability of PBAT. The PBAT/hemp films and paper coatings composted two times faster than those using pure PBAT. Full article

Cotton gin trash (CGT), a lignocellulosic waste generated during cotton fibre processing, has recently received significant attention for production of composite bio-plastics. However, earlier studies were limited to either with biodegradable polymers, through small-scale solution-casting method, or using industrially adaptable extrusion route, but with non-biodegradable polymers. In this study, a scale-up production of completely biodegradable CGT composite plastic film with adjustable biodegradation rate is proposed. First using a twin screw extruder, the prepared CGT powder was combined with polycaprolactone (PCL) to form pellets, and then using the compressing moulding, the pellets were transformed into bio-plastic composite films. Hydrophilic polyethylene glycol (PEG) was used as a plasticiser in the mixture and its impact on the biodegradation rate was analysed. The morphology of CGT bio-plastic composite films showed even distribution of CGT powder within the PCL matrix. The CGT incorporation improved the UV resistance, thermal stability, and Young’s modulus of PCL material. Further, the flexibility and mixing properties of the composites were improved by PEG. Overall, this study demonstrated a sustainable production method of CGT bio-plastic films using the whole CGT and without any waste residue produced, where the degradation of the produced composite films can be adjusted to minimise the environmental impact. Full article

Salt-tolerant plants, also known as halophytes, could provide a novel source of feedstock for biorefineries. After harvesting fresh shoots for food, the lignified fraction of Salicornia ramosissima J. Woods could be used to produce bioactive botanical extracts for high-value industries such as nutraceuticals, cosmetics, and biopharmaceuticals. The residual fraction after extraction can be further used for bioenergy or lignocellulose-derived platform chemicals. This work analysed S. ramosissima from different sources and growth stages. After pre-processing and extractions, the obtained fractions were analysed for their contents of fatty acids, pigments, and total phenolics. Extracts were also evaluated for their in vitro antioxidant properties and inhibitory effect towards enzymes related to diabetes, hyperpigmentation, obesity, and neurogenerative diseases. The ethanol extract from the fibre residue and the water extract from completely lignified plants showed the highest concentration of phenolic compounds along with the highest antioxidant potential and enzyme-inhibitory properties. Hence, they should be further explored in the context of biorefinery. Full article

The growth and nutritional profile of the black soldier fly larvae (BSFL) is usually investigated and compared when the larvae feed on substrates that differ in the chemical composition as well as physical properties. This study compares BSFL growth on substrates that differ primarily in physical properties. This was achieved by using various fibres in the substrates. In the first experiment, two substrates with 20% or 14% chicken feed were mixed with three fibres (cellulose, lignocellulose, or straw). In the second experiment, the growth of BSFL was compared with a 17% chicken feed substrate that additionally contained straw with different particle sizes. We show that the substrate texture properties values did not influence the BSFL growth, but the bulk density of the fibre component did. The substrate mixed with cellulose led to higher larvae growth over time in comparison to substrates with higher bulk density fibres. BSFL grown on the substrate mixed with cellulose reached their maximum weight in 6 days instead of 7. Neither the fibres nor the nutrient level changed the crude protein content of BSFL and the values ranged between 33.5% and 38.3%, but an interaction between the fibre and nutrient level was observed. The size of straw particles in the substrates influenced the BSFL growth and led to a 26.78% difference in Ca concentration, a 12.04% difference in Mg concentration, and a 35.34% difference in P concentration. Our findings indicate that the BSFL-rearing substrates can be optimised by changing the fibre component or its particle size. This can improve the survival rate, reduce the cultivation time needed to reach the maximum weight, and alter the chemical composition of BSFL. Full article

Sansevieria trifasciata fibre (STF) is a lignocellulosic material which could be utilised for reinforcement composites. Surface modification is often needed to improve the compatibility of hydrophilic STF and hydrophobic resin. In this study, treatments for natural fibres to attain superhydrophobic properties were carried out using silica nanoparticles and fluorosilane. Sansevieria trifasciata fibres (STF) were subjected to treatment by deposition of silica (SiO₂) nanoparticles which were prepared by the sol-gel method, then followed by modification with fluorosilane, namely 1H, 1H, 2H, 2H-perfluorooctyltriethoxysilane (PFOTS). The presence of SiO₂ nanoparticles and PFOTS were evaluated using Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDX). The crystallisation properties and thermal behaviour of STF were studied through X-ray diffraction (XRD) and thermogravimetric (TGA) analysis, respectively. The hydrophobicity of STF was determined by water contact angle (WCA) measurement. The results show that nanoscale SiO₂ particles were deposited on the STF surface, and PFOTS were covalently linked to them. The SiO₂ nanoparticles provide surface roughness to the fibres, whereas the long-chain fluorine on PFOTS lowered the surface free energy, and their combination in these treatments has successfully modified the STF surface from hydrophilic into superhydrophobic with a WCA of 150° and sliding angle of less than 10°. Altogether, a non-toxic, simple, and promising method of imparting hydrophobicity on natural fibres was developed, opening new opportunities for these fibres as reinforcement for composite parts. Full article

Plant-derived fibres, called lignocellulosic fibres, are a natural alternative to synthetic fibres in polymer composite reinforcement. Utilizing renewable resources, such as fibre-reinforced polymeric composites made from plant and animal sources, has become a crucial design requirement for developing and producing parts for all industrial goods. Natural-fibre-based composites are used for door panels, trays, glove boxes, etc. This study involves developing and thermal analysing a flax fibre reinforced with phenol–formaldehyde resin hybridization with ramie fibre by way of a vacuum infusion process. As per ASTM Standard, eight different sequences were fabricated and thermally characterized. In the present study, three stages of weight loss (%) are shown by the thermogravimetric analysis (TGA). The sample loses less weight during the first stage, more during the second, and more during the third. The sample’s overall maximum temperature was recorded at 630 °C. It was discovered that sample D (80.1 °C) had the highest heat deflection temperature, and sample B had the lowest (86.0 °C). Sample C had a low thermal expansion coefficient, while sample G had a high thermal expansion coefficient. Sample E had the highest thermal conductivity, measured at 0.213 W/mK, whereas sample A had the lowest conductivity, at 0.182 W/mK. From the present study, it was found that sample H had better thermal characteristics. The result of the present investigation would generate thermal data regarding hybrid ramie and flax composites, which would be helpful for researchers and practitioners involved in the field of biocomposites. Full article