Search Results (1,766)

We demonstrate Kerr-lens mode-locked operation of a Tm,Ho:Ca(Gd,Y)AlO₄ laser pumped by a narrow-linewidth, continuous-wave Ti:sapphire laser at 797 nm. Soliton pulses as short as 145 fs are generated at 2087.8 nm in σ-polarization via soft-aperture Kerr-lens mode-locking, with an average output power of 203 mW (0.5% output coupler) at ~80.5 MHz. To the best of our knowledge, this result represents the first demonstration of a Kerr-lens mode-locked laser based on a Tm,Ho:Ca(Gd,Y)AlO₄ crystal exhibiting both structural and compositional disorder. Full article

The interaction between laser irradiation and energetic materials is critically influenced by microstructural void defects that determine local energy deposition and initiation sensitivity. In this work, a three-dimensional finite-difference time-domain (3D-FDTD) method was employed to investigate the modulation effects of void defects on optical field distributions and hot spot formation in RDX energetic crystals. The influences of void geometry, spatial position, and void number on the modulation of the incident laser beam were systematically analyzed. It reveals that void defects exhibit strong focusing and scattering behavior, leading to localized high-intensity regions both inside RDX bulk crystals and in void defects. For a single void defect, increasing either the width or depth can significantly enhance the peak electric field and thus the laser sensitivity of RDX crystals. When two voids are present, the number of high-intensity spots first increases and then decreases with increasing separation distance, and the strongest modulation effects are obtained at separations of 0.75λ–3λ. Furthermore, as the number of void defects increases, the modulation effect intensifies, promoting the formation of more hot spots. These findings provide quantitative insight into how void structures govern laser–matter interactions in energetic crystals, offering guidance for understanding and controlling laser initiation behavior. Full article

The stimulated assembly/disassembly of particles is a technique allowing for precise spatial and temporal control over the resulting structures to be realized. The application of a photosensitive liquid crystal (LC) allows the use of a photo-initiated order–disorder transition for the ordering and redistribution of dispersed nanoparticles. The semiconductor quantum dots (QDs) among them are useful for the imaging of such redistribution through simple luminescent microscopy with excitation by laser radiation at a wavelength of 532 nm. Doping the LC matrix with azo-chromophore molecules allowed us to localize the light-driven phase transition of the LC from the organized to the isotropic phase inside the spot, illuminated by ultraviolet (UV) light through a slit. The phase transition leads to a redistribution of the QDs within the matrix, followed by QD-rich region formation. After the termination of UV illumination, the QDs were found to form droplets in the region where UV illumination resulted in a homogeneous distribution of the QDs. The translation of the sample through the UV-illuminated spot resulted in QD accumulation inside the isotropic phase at the borders of the isotropic phase. The results obtained provide a good agreement with the model calculations of nanoparticle diffusion at the LC phase–isotropic liquid interface. Full article

Ultra-precision single-point diamond turning (SPDT) remains the core process for fabricating optical-grade surfaces with nanometric roughness and sub-micrometer form accuracy. However, machining hard-to-cut or brittle materials such as high-entropy alloys, metals, ceramics, and semiconductors is limited by severe tool wear, high cutting forces, and brittle fracture. To overcome these challenges, a new generation of non-conventional assisted and hybrid SPDT platforms has emerged, integrating multiple physical fields, including mechanical, thermal, magnetic, chemical, or cryogenic methods, into the cutting zone. This review comprehensively summarizes recent advances in hybrid non-conventional assisted SPDT platforms that combine two or more assistive techniques such as ultrasonic vibration, laser heating, magnetic fields, plasma or gas shielding, ion implantation, and cryogenic cooling. The synergistic effects of these dual-field platforms markedly enhance machinability, suppress tool wear, and extend ductile-mode cutting windows, enabling direct ultra-precision machining of previously intractable materials. Recent key case studies are analyzed in terms of material response, surface integrity, tool life, and implementation complexity. Comparative analysis shows that hybrid SPDT can significantly reduce surface roughness, extend diamond tool life, and yield optical-quality finishes on hard-to-cut materials, including ferrous alloys, composites, and crystals. This review concludes by identifying major technical challenges and outlining future directions toward optimal hybrid SPDT platforms for next-generation ultra-precision manufacturing. Full article

The polar oxide Lithium Niobate Tantalate is probed using time-resolved luminescence spectroscopy with the goal of revealing an initial structural insight into the solid solution by analyzing the spectral properties and dynamics of radiatively decaying self-localization phenomena. A blue-green luminescence band can be induced by ultraviolet nanosecond laser pulses with a temperature-dependent intensity and spectral width, pointing to the radiative decay of optically generated self-trapped excitons as its origin, i.e., electron–hole pairs with strong coupling to either the NbO₆- or TaO₆-octahedra. The luminescence decay takes place in the microsecond time range and deviates significantly from a single exponential behavior, so the determined lifetime constants of up to ≈70 μs and stretching factors (1/3–1/5) are validated in more detail using alternative evaluation methods. We discuss our findings, considering the interplay of radiative and non-radiative decay channels, the transition from self-trapped to free excitons, and the presence of a structural disorder of the oxygen octahedra in the solid solutions. Overall, our results suggest self-trapped excitons as local probes for an initial structural elucidation and provide essential information about further experimental and theoretical studies on the atomic structure of Lithium Niobate Tantalate, but also for improving the crystal quality in the framework of applications in photonics and quantum optics. Full article

The Southwestern Fujian Region is one of the important Fe polymetallic metallogenic belts in China. The Makeng-Yangshan Fe skarn sub-belt within it contains several deposits that share a similar geological setting, mineralization age, and genetic type, yet exhibit significant differences in metal endowment. To investigate the poorly constrained factors responsible for these differences, this paper focused on the mineral chemistry of garnets associated with magnetite from the Makeng, Luoyang, and Yangshan Fe deposits within the sub-belt, employing in situ laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS) for trace element analysis. Our results reveal that garnet from all three deposits are andradite-dominated and features a chondrite-normalized REE fractionation pattern exhibiting enrichment in LREE relative to HREE, indicating crystallization from unified, mildly acidic fluids under high oxygen fugacity (f_O2) conditions. However, both the Makeng and Luoyang garnets showed a strong positive Eu anomaly, whereas the Yangshan garnets displayed the weakest Eu anomaly among the three deposits, which can likely be attributed to the highest f_O2 environment of the Yangshan deposit. Furthermore, garnet Y/Ho ratios and Y-ΣREE correlations demonstrate that the Makeng and Luoyang garnets crystallized in an open fluid system that were primarily of magmatic-hydrothermal origin with substantial external fluid (e.g., meteoric water) involvement, whereas the Yangshan garnet reflects a relatively closed fluid system that was predominantly of magmatic-hydrothermal origin with limited external fluid input. These geochemical differences have direct implications for exploration: the open-system Makeng deposit holds promise for Mo-W-Sn mineralization, as does the Luoyang deposit for W-Sn, whereas the closed-system Yangshan shows little potential for these metals. In addition, this study reveals that Pb and Zn concentrations in garnet are not reliable exploration indicators. Overall, these findings provide important mineralogical constraints on the factors controlling deposit scale and metal associations, thereby enhancing the understanding of regional metallogeny and guiding future mineral exploration. Full article

The effect of Mn-doped zinc ferrite nanoparticles at a low volume concentration (1 × 10⁻⁴) on structural changes in the nematic liquid crystals 6CHBT and 5CB, induced by weak magnetic fields, was investigated using surface acoustic wave (SAW) and light transmission (LT) techniques. Structural changes caused by the applied magnetic field, in both increasing and decreasing modes, as well as after pulsed changes, were examined by measuring the responses of SAW attenuation and LT using a linearly polarized laser beam. The influence of nanoparticle shape (rods, needles, and clusters) and temperature on the structural changes was investigated. A shift in the threshold field and the transition temperature was observed. In addition, the magnetic properties of the individual samples in powder form were examined using M–H curves, M–T curves, and XRD patterns. The results obtained from all measurements are compared, and the effectiveness of each technique, considering the influence of nanoparticle shape and suspension stability, was evaluated. Full article

It is difficult to achieve ultra-precision machining (UPM) on semiconductor materials like single-crystal silicon because of their hardness and brittleness. To solve this issue, numerous field-assisted machining systems and their combinations have been suggested and developed. However, the difficulty in directly observing the physical variables limits our comprehension of the in-depth machining mechanisms of field-assisted machining. In this work, we investigated the machining mechanism of single-crystal silicon under the combination of laser heating and tool vibration using molecular dynamics (MD) simulations. The effect of tool vibration trajectory determined by different tool edge radii is discussed under the condition of raising temperature. The simulation results indicate that the surface morphology is closely related to vibration and heating parameters. Raising the cutting temperature causes a reversed relation between tool edge radius and surface roughness. While the subsurface damage and internal stress are also determined by the tool edge radius and cutting temperature. The findings in this simulation could help to improve the understanding of machining mechanics in multi-field-assisted machining. Full article

Quantum sensing with nitrogen vacancy (NV) defects in diamond enables detection of extremely small changes in temperature, host material strain, and magnetic and electric fields. Action potential detection has previously been demonstrated with cardiac tissue and whole organisms using NV defects in bulk diamond crystals. Nanodiamonds (NDs) with NV defects were previously used as effective fluorescent markers, as they do not bleach under laser illumination like conventional fluorescent dyes. Subcellular-level action potential recording with NDs is yet to be demonstrated. Here, we report our results on the confocal imaging of NDs and the feasibility of optically detected magnetic resonance (ODMR) experiments with Cath.-a-differentiated (CAD) mouse brain cells. 10 nm and 60 nm NDs were shown to diffuse into cells within 30 min with no additional surface modification, as confirmed with confocal imaging. In contrast, 100 nm and 140 nm NDs were observed to remain localized on the cell surface. ND photoluminescence (PL) signals did not bleach over the course of 5 h long imaging studies. ODMR technique was used to detect externally applied millitesla-level magnetic fields with NDs in cell solutions. In summary, NDs were shown to be effective, non-bleaching fluorescent markers in mouse brain cells, with further potential for use in action potential recording at the subcellular level. Full article

Laser slicing has emerged as a promising low-kerf and low-damage technique for SiC wafer fabrication; however, its effects on the crystal integrity, near-surface modification, and charge-transport properties require further clarification. Here, a heavily N-doped 4° off-axis 4H-SiC wafer was sliced using an ultraviolet (UV) picosecond laser, and both laser-irradiated and laser-sliced surfaces were comprehensively characterized. X-ray diffraction and pole figure measurements confirmed that the 4H stacking sequence and macroscopic crystal orientation were preserved after slicing. Raman spectroscopy, including analysis of the folded transverse-optical and longitudinal-optical phonon–plasmon coupled modes, enabled dielectric function fitting and determination of the plasmon frequency, yielding a free-carrier concentration of ~3.1 × 10¹⁸ cm⁻³. Hall measurements provided consistent carrier density, mobility, and resistivity, demonstrating that the laser slicing process did not degrade bulk electrical properties. Multi-scale Atomic Force Microscopy (AFM), Angle-Resolved X-Ray Photoelectron Spectroscopy (ARXPS), Secondary Ion Mass Spectrometry (SIMS), and Transmission Electron Microscopy (TEM)/Selected Area Electron Diffraction (SAED) analyses revealed the formation of a near-surface thin amorphous/polycrystalline modified layer and an oxygen-rich region, with significantly increased roughness and thicker modified layers on the hilly regions of the sliced surface. These results indicate that UV laser slicing maintains the intrinsic crystalline and electrical properties of 4H-SiC while introducing localized nanoscale surface damage that must be minimized by optimizing the slicing parameters and the subsequent surface-finishing processes. Full article

Heterostructure (HS) refers to a class of structural materials composed of two or more different chemical components or crystal structures. Integration of Inconel 625 (IN625) nickel-based superalloy and Ti6Al4V (TC4) titanium alloy to a HS material offers a promising strategy to achieve graded thermo-mechanical properties, extended service temperature ranges, and significant weight reduction, which are highly desirable in aerospace applications. However, obtaining a better metallurgical bonding between the two alloys remains a critical challenge. In this study, laser directed energy deposition (L-DED) technology was employed to fabricate IN625/TC4 HS materials with a nonlinear gradient transition, following systematic investigations into the phase composition and crack sensitivity of IN625/TC4 gradient layers prepared from mixed powders of varying compositions. In addition, microstructure, phase distribution, and mechanical properties of HS materials at room temperature were characterized. The metallurgical defect-free IN625/TC4 HS material was successfully prepared, featuring a smooth transition of microstructure, reduced cracking sensitivity, and reliable metallurgical bonding. Furthermore, a novel design concept and illustrative reference for the L-DED fabrication of N625/TC4 HS material with excellent comprehensive performance was presented, while providing a theoretical metallurgical basis and data support for the potential applications of IN625/TC4 HS materials in the field of aerospace. Full article

The Yixingzhai deposit is a giant gold system containing four cryptovolcanic breccia pipes, several of which host significant porphyry-type gold orebodies at depth. A key exploration target is the Tietangdong cryptovolcanic breccia pipe, characterized by skarn alteration in its upper zones. However, the evolution of early hydrothermal fluids and their implications for gold enrichment potential remain poorly understood. This study employs an integrated approach—combining petrography, electron probe microanalysis, laser ablation-inductively coupled plasma–mass spectrometry (LA-ICP-MS), and LA-ICP-MS elemental mapping—to analyze zoned garnets within the Tietangdong skarn, with the aim of deciphering changes in magmatic–hydrothermal composition and physicochemical conditions, as well as their influence on gold enrichment. Textural and compositional data reveal three distinct generations of garnets. Garnets from generations I and III consist of a grossular–andradite solid solution and commonly exhibits optical anisotropy. In contrast, generation II garnet is predominantly andraditic and optically homogeneous. LA-ICP-MS elemental mapping of generations I and III indicates that both generations contain significant Al and Fe, with their optical anisotropy attributed to a high degree of Fe³⁺/Al³⁺ cationic ordering. Compared to generations I and III, generation II garnet displays distinct geochemical characteristics, including enrichment in Fe, As, Sn, W, and U, patterns enriched in light rare earth elements, a positive Eu anomaly, and a wide range of Y/Ho ratios. Garnets from generations I and III crystallized under relatively high-pressure, high-temperature, and low-oxygen fugacity conditions, whereas generation II garnets formed under lower pressure–temperature conditions and higher oxygen fugacity. Moreover, concentrations of Co, Ni, and Cu increase systematically from generation I to generation III. We interpret the sharp compositional break at generation II as recording of the pulsed injection of magmatic–hydrothermal fluids, which enhanced the potential for gold mineralization. The zoning patterns in garnet provide a robust record of the temporal evolution of physicochemical conditions and fluid composition in the hydrothermal system. Full article

In this study, we present a non-invasive and contactless method for estimating the internal temperature of Cr:LiCAF laser crystals using temperature-dependent shifts in fluorescence emission peaks. A high-resolution calibration dataset was created with 181 spectral points from 10 to 100 °C. Linear regression yielded a temperature estimation model with an R² of 0.73, which was validated under both lasing and non-lasing conditions. To further evaluate the reliability of this optical thermometry method, thermal imaging data from a FLIR E75 infrared camera were incorporated. Surface temperatures measured at various diode current levels closely matched the internal temperature predictions based on fluorescence shifts (MAE = 0.775 °C, R² = 0.993), confirming the robustness of the method. This dual-approach validation enhances confidence in using fluorescence-based diagnostics for real-time thermal monitoring in laser systems. The combined use of spectrometer-based and thermal camera measurements suggests potential for hybrid diagnostics in laser research and development, offering improved thermal feedback for optimizing high-power laser performance. Full article

Silicon carbide (SiC) single crystals are extensively utilized in various fields due to their exceptional properties, such as a wide bandgap and a high breakdown threshold. Nevertheless, the intrinsic high hardness of SiC creates significant challenges for contact machining. This study investigates the surface damage characteristics and underlying mechanisms involved in processing both high-purity silicon carbide (HP-SiC) and nitrogen-doped silicon carbide (N-SiC) crystals using fundamental-frequency nanosecond pulsed lasers. This study establishes a laser-induced damage threshold (LIDT) testing platform and employs the internationally standardized 1-ON-1 test method to evaluate the damage characteristics of HP-SiC and N-SiC crystals under single-pulse laser irradiation. Experimental results indicate that N-SiC crystals exhibit superior absorption characteristics and a lower LIDT compared with HP-SiC crystals. Subsequently, a defect analysis model was established to conduct a theoretical examination of defect information across various types of SiC. Under fundamental-frequency nanosecond pulsed laser irradiation, N-SiC crystals demonstrate a lower average damage threshold and a broader defect damage threshold distribution than their HP-SiC counterparts. By integrating multi-dimensional analytical methods—including photothermal weak absorption mechanisms and damage morphology analysis—the underlying damage mechanisms of the distinct SiC forms were comprehensively elucidated. Moreover, although N-SiC crystals show weaker photothermal absorption properties, they exhibit more pronounced absorption and damage response processes. These factors collectively account for the different laser damage resistances observed in the two types of silicon carbide crystals, implying that distinct processing methodologies should be employed for nanosecond pulsed laser treatment of different SiC crystals. This paper elucidates the damage characteristics of various SiC materials induced by near-infrared nanosecond pulsed lasers and explores their underlying physical mechanisms. Additionally, it provides reliable data and a comprehensive mechanistic explanation for the efficient removal of these materials in practical applications. Full article

Yuanjiang County is one of the most important gem-producing areas in China. The authors of this study discovered and collected gem-quality andradite Garnsts in the epidote amphibolite from the periphery of the ruby deposit in Shaku Village, Yuanjiang County. After careful observation of the collected andradite, it was found that these andradite samples appear green when the thickness is less than 2 mm and reddish-brown when the thickness is greater than 2 mm, exhibiting the typical Usambara effect. To investigate the gemological and spectroscopic characteristics of Yuanjiang andradite, this study conducted basic gemological tests, microscopic observation, electron probe microanalysis (EPMA), ultraviolet–visible (UV-Vis) absorption spectroscopy, Fourier transform infrared (FTIR) spectroscopy, and laser Raman spectroscopy on the collected samples. Tests show that Yuanjiang andradite has a lower specific gravity than typical andradite, which is due to the presence of epidote inclusions inside. EPMA results indicate that the samples contain a certain amount of Cr element. The crystal chemical formula of the samples calculated from the EPMA results is (Ca_2.89–2.93, Mn_0.01–0.02, Fe_0.15–0.10)(Fe_1.69–1.95, Al_0.00–0.23, Cr_0.00–0.23, Si_0.05–0.08)(SiO₄)₃. UV-Vis tests show that the samples have transmission windows in both the green- and red-light regions, with Fe³⁺ and Cr³⁺ acting as the main chromogenic ions, among which Cr³⁺ is crucial for the occurrence of the Usambara effect. The FTIR and Raman test results are basically the same as previous research results, but some peak positions related to metal cations differ from the theoretical values, which may be caused by the presence of a certain amount of Cr³⁺ in the samples. Full article