Search Results (30)

The rapid increase in global data generation has intensified the demand for magnetic storage systems with substantially higher areal density. Double-layer bit-patterned media recording (DLBPMR), which integrates the benefits of bit-patterned media recording (BPMR) and double-layer magnetic recording (DLMR), provides a promising pathway by combining nanoscale patterned islands with multilayer recording structures. However, severe two-dimensional intersymbol interference (ISI) within each layer, together with interlayer interference (ILI) between stacked layers, continues to present significant challenges for reliable data detection. To address these issues, this work investigates and advances the structure of DLMR to improve signal separation and recovery. In particular, we emphasize that detection plays a crucial role in mitigating both ISI and ILI. Accordingly, we propose a maximum a posteriori (MAP) detection scheme derived for a newly developed generalized two-layer partial-response (PR) model that accurately characterizes intra-layer ISI and cross-layer interference coupling. A parallel detection architecture is designed and employed for the upper and lower layers of the DLMR system, enabling the exchange of extrinsic information and enhancing MAP detection performance. Simulation results demonstrate that the proposed PR modeling and MAP-based detection framework achieves significant bit error rate (BER) improvements over existing detection methods, highlighting its strong potential for next-generation ultra-high-density DLBPMR systems. Full article

A state-of-the-art tunnel magnetoresistance (TMR) sensor architecture, which is based on the perpendicularly magnetized magnetic tunnel junction (pMTJ), is introduced and engineered for ultrafast, high thermal stability, and linearity for magnetic field detection. Limitations in high-frequency environments, stemming from insufficient thermal stability and slow recovery times in conventional TMR sensors, are overcome by this approach. The standard MRAM structure is modified, and the Ruderman–Kittel–Kasuya–Yosida (RKKY) interaction is employed to give a strong, internal restoring torque to the storage layer magnetization. Sensor linearity is also ensured by this RKKY mechanism, and rapid relaxation to the initial spin state is observed when an external field is removed. The structural and magnetic properties of the multilayer stack are experimentally demonstrated. Robust synthetic antiferromagnetic (SAF) coupling is confirmed by using polar MOKE spectroscopy with an optimal Ru insertion layer thickness (0.6 nm), which is essential for high thermal stability. Subsequently, an ultrafast response of this TMR sensor architecture is probed by micromagnetic simulations. The storage layer magnetization rapidly recovers to the SAF state within an ultrashort time of 5.78 to 5.99 ns. This sub-6 ns recovery time scale suggests potential operation into the hundreds of MHz range. Full article

Topological magnetic textures—including skyrmions, Bloch points, and chiral bobbers—exhibit extraordinary properties with significant potential for advanced information technologies. However, achieving precise control over specific topological states requires an understanding of their formation mechanisms and stabilization criteria in nanoscale materials. Our work addresses this challenge by investigating how tailored interactions in ferromagnetic multilayers govern the emergence of specific topological configurations. In this study, we investigate topological magnetic structures in ferromagnetic multilayers, focusing on the interplay between magnetic anisotropy, the Dzyaloshinskii–Moriya interaction, and interlayer exchange coupling. We demonstrate how these interactions govern the formation and stability of diverse 3D topological configurations, including Bloch-point-like structures, conical skyrmions, chiral bobbers, and skyrmion tubes. Optimal conditions for stabilizing specific defect types have been identified and phase diagrams have been constructed as a function of material parameters. These findings provide insights into the controlled design of magnetic textures for advanced spintronic applications. Full article

The increasing shortage of drinking water, driven by reduced rainfall and the intensification of industrial and agricultural activities, has raised justified concerns about the quantity and quality of available water resources. These sectors not only demand high water consumption but also discharge large amounts of toxic substances such as organic matter, metal ions and inorganic anions, posing risks to both public health and the environment. This study evaluated the effectiveness of clay-based nanomaterials in the treatment of contaminated industrial wastewater from the mining sector. The materials tested included montmorillonite, high-loading expandable synthetic mica, and their organically functionalized forms (MMT, Mica-Na-4, C18-MMT, and C18-Mica-4). The experimental results show that these clays had minimal impact on the pH of the water, while a notable decrease in the chemical oxygen demand (COD) was observed. Ion chromatography indicated an increase in nitrogen and sulfur compounds with higher oxidation states. Inductively coupled plasma analysis revealed a significant reduction in the calcium concentration and an increase in the sodium concentration, likely due to cation exchange mechanisms. However, the removal of copper and iron was ineffective, possibly due to competitive interactions with other cations in the solution. Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) confirmed the structural modifications and interlayer spacing changes in the clay materials upon exposure to contaminated water. These findings demonstrate the potential of clay minerals as effective and low-cost materials for the remediation of industrial wastewater. Full article

V/Fe multilayers were prepared on naturally oxidized Si(100) substrates at room temperature (RT) by UHV magnetron sputtering. Mixing effects at the Fe–V interfaces were investigated in-situ, directly after deposition, by means of X-ray photoelectron spectroscopy (XPS). The results of systematic in-situ XPS studies of the integral intensity of the Fe-2p peak, as a function of the nominal thickness of the Fe sublayer deposited on vanadium, allowed us to estimate the thickness of the pure iron layer that forms the mixed layer at about 0.4 nm. Assuming the same thickness of the vanadium layer that forms the mixed layer, the estimated thickness of the mixed layer near the Fe–V interface was about 0.8 nm. In the analysis of magnetic hysteresis loops, in addition to the bilinear (J₁) and biquadratic (J₂) coupling constant, the contribution of the cubic exchange constant (J₃) was taken into account, which also contributed significantly to the total energy. Higher order interactions (J₂ and J₃) are particularly important for V spacer thicknesses greater than 7 atomic monolayers. Hydrogen absorption in V/Fe multilayers at RT and a pressure of about 1 bar causes an increase in the biquadratic coupling constant J₂, while the values of J₁ and J₃ are reduced. A comparison of the obtained experimental results and available theoretical models leads to the conclusion that the mechanism of “fluctuating thickness of the non-magnetic spacer” could be responsible for the biquadratic exchange coupling. On the other hand, the “loose spins” model can explain the cubic coupling in the V/Fe multilayers. The modification of the interlayer exchange coupling using hydrogen is fully reversible. Full article

During the coiling process of a hot-rolled strip, with the increasing layers the temperature and stress distribution inside the coil constantly change and interact with each other. Due to the contact with the sleeve and the transition of the heat exchange state, it is inaccurate to consider the temperature of the whole coil as the coiling temperature set by the process requirement. Meanwhile, due to the periodic interlayer contact in the radial direction, the relation between stress and deformation is nonlinear. For the coiling process, it is difficult to consider the above factors using conventional methods. Therefore, an incremental model has been established to couple the temperature and stress of the coil. In order to obtain the mechanical properties of the strip and radial elastic modulus of the coil, tensile tests and laminated compression experiments are conducted at different temperatures. The effects of changes in strip thickness, coiling tension, and initial temperature of the sleeve on the stress and the temperature inside the coil are studied. Finally, by comparing the model results with measurements and analytical solutions, the effectiveness of the incremental coupled model is verified and the errors caused by the analytical method are analyzed. Full article

Current-induced field-free magnetic switching using spin–orbit torque has been an important topic for decades due to both academic and industrial interest. Most research has focused on introducing symmetry breakers, such as geometrical and compositional variation, pinned layers, and symmetry-broken crystal structures, which add complexity to the magnetic structure and fabrication process. We designed a relatively simple magnetic structure, composed of a [Co/Pt] multilayer and a Co layer with perpendicular and in-plane magnetic anisotropy, respectively, with a Cu layer between them. Current-induced deterministic magnetic switching was observed in this magnetic system. The system is advantageous due to its easy control of the parameters to achieve the optimal condition for magnetic switching. The balance between magnetic anisotropic strength and interlayer coupling strength is found to provide the optimal condition. This simple design and easy adjustability open various possibilities for magnetic structures in spin-based electronics applications using spin–orbit torque. Full article

In advancing the study of magnetization dynamics in STT-MRAM devices, we employ the spin drift–diffusion model to address the back-hopping effect. This issue manifests as unwanted switching either in the composite free layer or in the reference layer in synthetic antiferromagnets—a challenge that becomes more pronounced with device miniaturization. Although this miniaturization aims to enhance memory density, it inadvertently compromises data integrity. Parallel to this examination, our investigation of the interface exchange coupling within multilayer structures unveils critical insights into the efficacy and dependability of spintronic devices. We particularly scrutinize how exchange coupling, mediated by non-magnetic layers, influences the magnetic interplay between adjacent ferromagnetic layers, thereby affecting their magnetic stability and domain wall movements. This investigation is crucial for understanding the switching behavior in multi-layered structures. Our integrated methodology, which uses both charge and spin currents, demonstrates a comprehensive understanding of MRAM dynamics. It emphasizes the strategic optimization of exchange coupling to improve the performance of multi-layered spintronic devices. Such enhancements are anticipated to encourage improvements in data retention and the write/read speeds of memory devices. This research, thus, marks a significant leap forward in the refinement of high-capacity, high-performance memory technologies. Full article

This research aims to prepare different antioxidant intercalated layered double hydroxides (LDHs) and compare the thermal oxidation and ultraviolet (UV) aging resistances of different modified asphalts. The ion exchange technique was used to intercalate three different antioxidants: 3-(3,5-di-tert-butyl-4-carboxyphenyl) propionic acid, antioxidant 1222, and sodium dibutyl dithiocarbamate (rubber accelerator TP) into the interlayer of LDHs. The morphology, structures, UV blocking, and free radical scavenging properties of different antioxidant intercalated LDHs were characterized, respectively. The effects of the anti-aging agents on the physical properties (penetration, softening point, ductility, and viscosity); rheological behaviors (complex modulus and phase angle); and functional groups (C=O and S=O) of asphalt both before and after thermal oxidation aging and UV aging were systematically investigated. The results of the crystal structure and functional group analysis show that the three different antioxidants can be successfully inserted into the interlayer of LDHs without destroying their layered structures. Antioxidant intercalated LDHs exhibit a remarkable capacity for absorbing UV rays, coupled with a moderate ability to reflect UV light. Moreover, the inclusion of antioxidants into the interlayers of LDHs confers upon them the ability to scavenge free radicals. After 2 h of reaction, the free radical scavenging rates of LDHs-3, LDHs-1222, and LDHs-TP were 57.7%, 35.6%, and 17.1%, respectively. With an increase in the content of the antioxidant intercalated LDHs, the performance of the modified asphalt varies, and 4% is the optimal content of the anti-aging agents. Asphalts with the three antioxidant intercalated LDHs all had favorable storage stability, and their physical and rheological properties were improved after aging compared to LDHs-modified asphalt. The LDHs-3-modified asphalt showed the best anti-ultraviolet aging effect, while LDHs-1222-modified asphalt showed the best anti-thermal oxidation aging effect. This research lays the foundation for developing aging-resistant asphalt and improving the durability of asphalt pavement. Full article

Four new metal–organic frameworks based on cobalt(II) salts and 1,4-diazabicyclo[2.2.2]octane N,N’-dioxide (odabco) were obtained. Their crystallographic formulae are [Co₃(odabco)₂(OAc)₆] (1, OAc⁻ = acetate), [Co(H₂O)₂(HCOO)₂]·odabco (2), [Co₂(H₂O)(NO₃)(odabco)₅](NO₃)₃·3.65H₂O (3), and [Co₂(DMF)₂(odabco)₄](NO₃)₄·3H₂O (4; DMF = N,N-dimethylformamide). Crystal structures of 1–4 were determined by single-crystal X-ray crystallography. Coordination polymer 1 comprises binuclear and mononuclear metal–acetate blocks alternating within uncharged one-dimensional chains, in which odabco acts as a bridging ligand. A layered Co(II) formate 2 contains odabco only as guest molecules located in the interlayer space. Layered compound 3 and three-dimensional 4 have cationic coordination frameworks with 26% and 34% specific void volumes, respectively, unveiling high structural diversity of Co(II)-odabco MOFs based on quite a rare aliphatic moiety. Magnetization measurements were performed for 1, 3, and 4 and the obtained data were interpreted on the basis of their crystal structures. A strong (J/k_B~100 K) antiferromagnetic coupling was found within binuclear metal blocks in 1. Ion exchange experiments revealed a considerable iodide uptake by 3 resulting in an up to 75% guest nitrate substitution within the voids of a coordination framework, found by capillary zone electrophoresis data and confirmed by single-crystal XRD. A preservation of 3 crystallinity during the exchange allowed for the guest I⁻ positions within a new adduct with the formula [Co₂(H₂O)(NO₃)(odabco)₅]I₂(NO₃)·1.85H₂O (3-I) to be successfully determined and the odabco aliphatic core to be revealed as a main adsorption center for quite large and easily polarizable iodide anions. In summary, this work presents a comprehensive study for a series of 1,4-diazabicyclo[2.2.2]octane N,N’-dioxide-based MOFs of cobalt(II) within the framework of magnetic properties and reports the first example of anion exchange in odabco-based coordination networks, supported by direct X-ray structural data. The reported results unveil promising applications of such frameworks bearing ligands with an aliphatic core in the diverse structural design of selective adsorbents and other types of functional materials. Full article

Magnetic heterojunction structures with a suppressed interfacial Dzyaloshinskii–Moriya interaction and a sustainable long-range interlayer exchange coupling are achieved with an ultrathin platinum insertion layer. The systematic inelastic light scattering spectroscopy measurements indicate that the insertion layer restores the symmetry of the system and, then, the interfacial Dzyaloshinskii–Moriya interaction, which can prevent the identical magnetic domain wall motions, is obviously minimized. Nevertheless, the strong interlayer exchange coupling of the system is maintained. Consequently, synthetic ferromagnetic and antiferromagnetic exchange couplings as a function of the ruthenium layer thickness are observed as well. Therefore, these optimized magnetic multilayer stacks can avoid crucial issues, such as domain wall tilting and position problems, for next-generation spintronic logic applications. Moreover, the synthetic antiferromagnetic coupling can open a new path to develop a radically different NOT gate via current-induced magnetic domain wall motions and inversions. Full article

Since the discovery of the low-temperature, long-range ferromagnetic order in monolayers Cr₂Ge₂Te₆ and CrI₃, many efforts have been made to achieve a room temperature (RT) ferromagnet. The outstanding deformation ability of two-dimensional (2D) materials provides an exciting way to mediate their intrinsic ferromagnetism (FM) with strain engineering. Here, we summarize the recent progress of strain engineering of intrinsic FM in 2D van der Waals materials. First, we introduce how to explain the strain-mediated intrinsic FM on Cr-based and Fe-based 2D van der Waals materials through ab initio Density functional theory (DFT), and how to calculate magnetic anisotropy energy (MAE) and Curie temperature (T_C) from the interlayer exchange coupling J. Subsequently, we focus on numerous attempts to apply strain to 2D materials in experiments, including wrinkle-induced strain, flexible substrate bending or stretching, lattice mismatch, electrostatic force and field-cooling. Last, we emphasize that this field is still in early stages, and there are many challenges that need to be overcome. More importantly, strengthening the guideline of strain-mediated FM in 2D van der Waals materials will promote the development of spintronics and straintronics. Full article

Domain wall mobility as a function of nonmagnetic interlayer thickness and temperature was studied in ultrathin exchange-coupled ferromagnetic layers using magneto-optic Kerr microscopy. The system under study is a Pt/Co/Pt/Co/Pt heterostructure having perpendicular magnetic anisotropy and a middle Pt layer with spatially variable thickness. The ferromagnetic interaction between the Co layers is observed when the Pt interlayer thickness varies from 5 to 6 nm in a temperature range of 200–300 K. There is a certain interval of Pt layer thickness where domain walls in both ferromagnetic layers move independently. Nonlinear dependence of the domain wall displacement on the applied field was measured. It is shown that an equilibrium position of the relaxed domain wall depends on field, temperature, and the nonmagnetic interlayer thickness. This position is determined by the energy balance: (i) domain wall displacement provided by the applied field, (ii) interlayer exchange interaction in the area swept by the domain wall, and (iii) domain wall coercivity. The mechanism of domain wall stabilization in terms of independent wall motion near critical thickness was considered. It is found that both the coercivity of the Co layer and the critical thickness decrease at higher temperature, while the interlayer exchange constant J is changed weakly. Full article

Skyrmions are promising for the next generation of spintronic devices, which involves the production and transfer of skyrmions. The creation of skyrmions can be realized by a magnetic field, electric field, or electric current while the controllable transfer of skyrmions is hindered by the skyrmion Hall effect. Here, we propose utilizing the interlayer exchange coupling induced by the Ruderman–Kittel–Kasuya–Yoshida interactions to create skyrmions through hybrid ferromagnet/synthetic antiferromagnet structures. An initial skyrmion in ferromagnetic regions could create a mirroring skyrmion with an opposite topological charge in antiferromagnetic regions driven by the current. Furthermore, the created skyrmions could be transferred in synthetic antiferromagnets without deviations away from the main trajectories due to the suppression of the skyrmion Hall effect in comparison to the transfer of the skyrmion in ferromagnets. The interlayer exchange coupling can be tuned, and the mirrored skyrmions can be separated when they reach the desired locations. Using this approach, the antiferromagnetic coupled skyrmions can be repeatedly created in hybrid ferromagnet/synthetic antiferromagnet structures. Our work not only supplies a highly efficient approach to create isolated skyrmions and correct the errors in the process of skyrmion transport, but also paves the way to a vital information writing technique based on the motion of skyrmions for skyrmion-based data storage and logic devices. Full article

Different amounts of sodium-alendronate (ALN) were loaded into layered zirconium phosphates of alpha and gamma type (αZP and γZP) by means of topotactic exchange reactions of phosphate with ALN. In order to extend the exchange process to the less accessible interlayer regions, ALN solutions were contacted with colloidal dispersions of the layered solids previously exfoliated in single sheets by means of intercalation reaction of propylamine (for αZP) or acetone (for γZP). The ALN loading degree was determined by liquid P-nuclear magnetic resonance (NMR) and inductively coupled plasma (ICP), and it was reported as ALN/Zr molar ratios (Rs). The maximum R obtained for γZP was 0.34, while αZP was able to load a higher amount of ALN, reaching Rs equal to 1. The synthesized compounds were characterized by X-ray powder diffractometry, scanning electron microscopy (SEM), solid-state NMR, and infrared spectroscopy. The way the grafted organo-phosphonate groups were bonded to the layers of the host structure was suggested. The effect of ZP derivatives was assessed on cell proliferation, and the results showed that after 7 days of incubation, none of the samples showed a decrease in cell proliferation. Full article